Search Documents

By T. Hadley, E. Catovic

"Northern Minerals Limited’s (ASX: NTU) flagship project is the Browns Range Rare Earth Project (the Project) located in Western Australia, consisting of a number of deposits with high value, heavy rare earth elements, in particular yttrium, terbium, and dysprosium. The deposits are dominated by xenotime mineralisation, which occurs within hydrothermal silicified and hematitic breccias. The Company delivered an initial JORC compliant resource estimate for the Project at the end of 2012 of 10,500 t of contained total rare earth oxides (TREO), which was increased to 28,084t of contained TREO in October 2013 and further enlarged to 47,997 t of contained TREO in February 2014. Concurrent with the growth of the Project resource base, significant progress has been made in developing the metallurgical process for the beneficiation and extraction of rare earth elements (REE’s) from the xenotime mineralisation. Development of the beneficiation circuit evaluated several process options and selected whole-ore flotation and magnetic separation, followed by flotation (hybrid circuit) as the two preferred flowsheets to pilot, following encouraging results on the bench of 83% and 86% recovery to a 20% TREO mineral concentrate respectively. Several downstream hydrometallurgical extraction flowsheets were evaluated. However, the following two preferred process flowsheets were ultimately selected for further detailed investigation during the prefeasibility study: 1. Sulphation bake, water leach, purification, oxalate precipitation, and/or calcination to produce a mixed RE oxide; 2. Sulphation bake, water leach, phosphate precipitation, caustic conversion, HCl leach, and oxalate precipitation to produce a mixed RE oxalate. Excellent heavy rare earth oxide (HREO) extractions (~ 90%) from beneficiation concentrates were achieved on the bench for both circuits, however flowsheet 1 was ultimately selected as the preferred flowsheet to pilot due to lower capital and operating cost. A mixed rare earth oxalate (42% TREO) or oxide (92% TREO) can be produced with low levels of Th and U of 3 ppm and 6 ppm respectively."

Jan 1, 2014

By E. S. Schubert

Keywords: co-generation, furnace CO-gas cleaning, disintegrator scrubber, Theisen In a closed, electric, reduction furnace, no oxygen enters the furnace from the surrounding environment. The off-gases are thus not ?burnt? and therefore contain a considerable amount of CO and H2. Traditionally these gases have been captured and burnt in a flare stack. Recent developments have led operators of such furnaces to revise this strategy and to consider utilising these gases as a fuel for gas-fired generator sets to produce electricity, thus becoming more energy efficient. On 31 March 2010 the new emission standards, in accordance with the Air Quality Act, Act 39 of 2004, were promulgated. The minimum emission standards according to the act require that the particulate matter emissions from the primary fume-capture systems on closed furnaces for ?new plants? in ferroalloy and calcium carbide production not exceed 50 mg/Nm³ and 25 mg/Nm³, respectively. By implementing co-generation, the producer automatically complies with the new environmental emission standards for an off-gas. As much as 30% of the electrical power cost, which is set to double in the near future, can be saved by partly generating one?s own electrical power. In December 2010, the National Treasury published a discussion paper for public comment, one entitled ?Reducing greenhouse gas emissions: The carbon tax option?. Irrespective of how the tax is finally implemented, it will result in an increase of production costs in affected industries. This paper focuses on the characteristics of a furnace-off-gas cleaning system for closed ferroalloy smelters, characteristics that meet the requirements of both reducing solid-matter emissions and operating a safe and reliable gas plant.

Jan 1, 2011

By Jarrell C. Grout

The Bureau of Mines has developed a computer program for use in solving nonlinear regression problems. The program is written in a general form so that, regardless of the functional relationship, the unknown parameters may be evaluated by either the Gauss-Newton or the Newton-Raphson methods of iteration. Variances and covariances of the parameters, as derived from the law for the propagation of errors, are also determined.

Jan 1, 1969

By W. A. Selvig

EQUIREMENTS of montan wax for industrial use in the United States before World War II were met by imports, nearly all of which came from Germany. An important industry for extraction and refinement of this wax from certain brown coals had developed in Germany. At the beginning of the war, montan-wax imports were shut oft, and American industry was forced to rely largely on substitutes. Since the war, relatively small amounts have been imported from Czechoslovakia. Because of the shortage of montan wax at the close of the war and the fact that industry in the United States had to rely on foreign sources in the past, this investigation was started in 1945 to determine probable yields of wax from domestic lignite. Results of the investigation and the properties of extracted waxes are described in this report. Also included in the report are discussions of the occurrence and geology of lignite deposits of the United States from which samples were obtained for wax extraction and the petrographic composition of lignites, particularly in respect to those components that contribute to wax yields.

Jan 1, 1950

By Adrian Brown

Pilot Hole ?X? was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. Five permeability tests were performed at various stratigraphic levels within this hole. The test method used was that of pumping fluids out of the hole for three hours, using the air lift method, followed by a three-hour period where the recharge was observed. Transmissivity and permeability results were determined from these test data. The test procedure used is described and supporting data for the hydrologic tests are provided.

Jan 1, 1977

By Paul Clark

Generation - Profile l 9,726 megawatts (MW) of capacity l 46,877 gigawatt hours (GWh) produced at an average plant availability of 88.4% l 47 facilities in four geographies: Canada; the U.S.; Mexico; and Australia l Fuel mix of coal (62%), gas (26%), hydro and renewables (12%) l 23.2 million tonnes of coal mined l 47.0 million gigajoules (GJ) of gas consumed

May 1, 2004

By Robert A. Bauer, Paul B. DuMontelle

In 1985, participants of the multi-year Illinois Mine Subsidence Research Program conducted surveys of subsidence effects on crop production from current high-extraction mining methods, selected a site to characterize the profile, strain, fracture development in overburden materials and changes in aquifers produced by subsidence from high-extraction mining, characterized floor materia1 s in three mines, and established bibliographic reference and data base files. The Illinois State Geological Survey, University of Illinois at Urbana-Champaign, Southern Illinois University at Carbondale, Illinois Department of Mines and Minerals and Twin Cities Research Center of the U. S. Bureau of Mines are coordinating State and Federally funded research.

Jan 1, 1986

By L. E. Djingheuzian

"IntroductionDURING the past two decades an enormous amount of empirical data has been accumulating on grinding. These data have been obtained by mill operators on grinding ores with a diversity of characteristics, and generally they have been published. However, whenever an operator, who has started milling on a new ore, has tried to find a case in literature which would exactly fit his particular grinding problem, he has failed. Evidently, something fundamental has been lacking in all these empirical data, and, as a consequence, each new operator has had to undertake his own experimenting, get the best results he can, maybe publish these results, and let it go at that. This, in the writer's opinion, has been• due to the fact that even the ablest and most inquisitive millman has been forced to look on grinding as an art, and so, except very rarely, has not been able to find the time to stop and think; if he did so, it was rather in a philosophic way, that grinding is a fundamental process, a process that takes place in river beds, on the sea shore, etc.Nevertheless, when all the data so far published are correlated and examined as a whole, one is struck with the advances that have been made in grinding. The writer (7) had made such a study in 1949, and, when the correlation was completed, it showed that there was nothing heterogeneous about the accumulated data and that when brought together they were in harmony with each other. The writer's conclusion was that, if grinding criteria were defined and were expressed in such a way as to make integration of any data into basic formulae possible, grinding would be established as a mathematically exact science, and grinding worries of the harassed mill operator would be at an end!The first attempts to rationalize comminution were made by Rittinger and Kick. However, their theories led to endless disputes which did not accomplish much, except possibly clearing the path for subsequent investigators."

Jan 1, 1952

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By R Stimpson, B Johnson, B Hesse

During a period of twelve months between FY18-19, a series of trials were conducted to compare production drilling accuracy using two different methodologies, and the subsequent impact this had on stope performance (dilution and recovery). Testing was conducted at a series of underground mines in Australia. The drill rig’s existing alignment processes were compared to a new technology system, with the following observations: • The new technology was proven to limit rig alignment error, thereby reducing average blasthole deviation, resulting in an increase in the number of holes drilled within tolerance by up to 160%. • The increased accuracy reduced stope dilution significantly by reducing over-break of subgrade ore, whilst also increasing drilled meters (faster stope-cycle time), reducing the bridged tonnes ratio, and facilitating the capture of previously uneconomical stopes. A cost-benefit analysis extrapolated from each of the trials showed the extent to which the new technology, when applied to production data, reduced average dilution, increased ore recovery as well as general drill and blast productivity. In one such trial, the new technology was proven to have reduced average dilution by net 45.4%, which if applied to a full year’s production data, would result in AUD8.2M additional ore recovered, with AUD4.5M less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 to AUD106. This improvement was maintained over the following 12 months – reducing average dilution from 22% in FY17 to 12.1% in FY19.

Mar 15, 2021

By S. q. Honingh, G. Van Weert

Currently produced zinc-enriched blast furnace dust is stored on site at CORUS IJmuiden. To end this practise, a research program was started in 1996. Four technologies were studied: oxidative autoclave leaching in a chloride medium, fluid bed pyrohydrochloridisation (pyrohydrolysis) to yield lead-zinc-free (hematite) calcine, EAF (plasma) smelting/zinc fuming, and incorporation of the dust in 'iron foundry cupola charges. All aim to remove zinc and lead, recycle the iron residue internally, and produce a saleable zinc-lead product.

Jan 1, 2000

By F. Calizaya

The PT Freeport Indonesia‘s Deep Ore Zone(DOZ) copper deposit is located in the province of Irian-Jaya, Indonesia. Currently, a block cave mine is being developed around this deposit. Production is scheduled to start in year 2000 and to ramp up to25,000 tpd by year 2003. The air quantity requirement for this mine is equal to 780 m3/s. To supply this quantity, the mine will require five centrifugal fans (one 450 and four 750 kW fans). This study summarizes the technical aspects related to the installation and commissioning of one of these fans. The fan was installed on the surface in a parallel arrangement with two others. It has a design capacity of 240 m3/s of air at 2.2 kPa of static pressure. The study presents the installation details from the underground shaft excavation and portal development through fan testing and commissioning. It also presents the results of a monitoring system that was installed to determine the fan duties.

Jan 1, 2000

The mine surveillance and communication system hereafter described provides continuous local and remote monitoring of several parameters critical to normal mine operation at each of ten underground sites in the Bruceton Research Mine. The techniques employed are well proven and have been care-fully chosen to provide the best solution to the technical problems involved while giving special attention to economic considerations.

Jan 1, 1973

By Alastair Grogan, Ron Elliott, Dale MacLean

Blasting for armour stone presents many unique challenges. Often, blasters get themselves into trouble when they assume that they can simply modify a production blast design to produce the required fragmentation size. They bid on the project using typical production blasting costs, and then find that they cannot produce the required fragmentation size and quantity with an acceptable waste factor. This paper outlines industry best practice guidelines for the production of riprap or armour stone. The paper examines the importance of initial geological mapping to determine the average in-situ block size, and the advantages to be gained from working with the geology to maximize production of the required block sizes. The paper also outlines the importance of proper explosives selection as well as blast designs that are unique to the production of riprap. The paper reviews challenges and experiences realized from multiple projects in differing rock types.

By Joseph Coffman

There are 14 operations that supply 97% of the Market Economy Country (MEC) manganese and contain nearly all of its resources. Six mines account for about 70% of the production and 85% of the resources; there are no known resources that are economically close to those that are currently being mined. Costs (January 1989 dollars) of producing manganese concentrates from the operations evaluated are estimated to range from $ 0.96 to $ 1.86 per long ton unit (ltu or 22.4 lb) of contained manganese. Total MEC demonstrated resources evaluated amount to about 1.2 billion tons of in situ ore containing 474 million tons of manganese. Identified resources amount to about 1.8 billion tons of in situ material. Key results of the study indicate the following: 1. The MEC supply of manganese will be from the currently mined resources well into the next century. 2. Centrally Planned Economy Countries (CPEC's) will be increasingly dependent on MEC manganese ore and concentrate in the future. 3. At the 1976 to 1987 demand increase rate, total MEC resource needed through the year 2000 would be about 282 million tons of in situ material. 4. Transportation and infrastructure support will continue to be major elements of production costs.

Jan 1, 1992

By Sanjeeva Latchireddi

The effective utilization of the energy in comminution devices depend on how efficiently the broken particles leave the breakage field as soon as they reach product size. In crushers the transport of broken particles smaller than CSS is done by gravity (vertical) thus allowing the energy to be applied to new particles. However, in AG/SAG mills, gravity becomes the energy field and the transport of particles is horizontal which needs a suitable discharge mechanism and has been found to have significant effect on grinding efficiency. The material transport in AG/SAG mills depend on how efficiently the discharge system (grate and pulp lifters) operates. Material transport plays a significant role on efficiency of horizontal grinding mills ? AG/SAG/Ball mills. The magnitude of benefits that can be achieved with efficient material transport in AG/SAG mills has been demonstrated in a Greenfield milling operation at Mirabela Mineração?s SantaRita Nickel operation located in northeastern part of Bahia in Brazil. This grinding circuit was commissioned in October 2009, which was designed as a typical SABC circuit to grind 4.6 mtpa (575tph) to produce a P80 of 125um with 10-12% ball charge in SAG mill. However, it has been operating as ABC circuit without any grinding media in SAG mill. The nameplate design capacity has been achieved in few days and has gradually increased to an average of +800 tph and still it is operating in ABC mode. The milling circuit commissioning resulted in small and relatively simple measures to rectify, which was reflected in the rapid commissioning of the milling circuit and it achieved the nameplate capacity within days. The Santa Rita grinding circuit consists of one 30?x 15.4? 8.5MW SAG Mill fitted with Outotec patented Turbo Pulp Lifters (TPL TM ) in close circuit with HP400 short head pebble crusher and one 20? x 28.4? 5.5MW Ball Mill in closed circuit with Warman cyclone cluster fitted with 10 x 26? CAVEX cyclones. This paper examines the comminution design process, operating philosophies, experiences, post commissioning optimization, and future development works. Evaluation of the milling circuit performance relative to the design criteria is also discussed. Keywords: Autogenous Grate (AG), Semi-Autogenous Grate (SAG, Turbo Pulp Lifter (TPL)

Sep 1, 2012

By Edwards A. B

A table concentrate obtained experimentally by the New Occidental Gold Mines N.L. has unusual interest on account of the presence in it of abundant coated or "black" gold. The concentrate was obtained from ore from the New Cobar mine, Cobar, New South Wales, by feeding the oversize product from a "Dorr Bowl classifier to a Card table.Its assay value was 129 oz. of gold and 52 oz. of silver per ton, yet practically no free gold could be seen on panning.When, however, the concentrate was digested in hydrochloric acid fine rusty gold could be obtained by panning.The following chemical analysis was carried out by the mining company on a similar sample of concentrate.

Jan 1, 1941

By G. G. Eichholz

SUMMARY RADIOACTIVE dynamite has been prepared by introducing a small amount of antimony-124 into the explosive. Test work is described on the effectiveness of this tracer, on radiation levels in its neighbourhood, and on different methods of .application. Factors determining the choice of isotope, amount of activity, and overall cost of this process are discussed. INTRODUCTION Instances are known in which dynamite remains unexploded in drill holes in mining operations. Usually such 'bootlegs' are easily located by inspection of the face and the powder is removed before subsequent drilling is started. Occasionally, however, serious accidents occur because workmen drill into an undetected piece of dynamite. In order to avoid such accidents it was suggested that a different method of location might be tied, such as that afforded by the use of radioactive tracers. This paper describes some experiments that were carried out under the auspices of the Department of Mines and Technical Surveys, with the active co-operation of Canadian Industries Ltd. and Canadian Refractories Ltd., to test the feasibility of such a scheme.

Jan 1, 1957

By Miguel Angel Banuet Rodriquez, Hector Conceso Aragon

"Construction of the longest road tunnel in Mexico is part of Acapulco’s alternate roadway to the scenic roadway project. This article provides a brief summary regarding details of the construction since the project began. Work was done by skilled engineers and Mexican workers that includes outstanding execution of the work in an urban and tourist area. This project will have a strong impact on the steady development of the port of Acapulco.Project locationAcapulco’s Alternate Roadway Project is currently under construction in the city of Acapulco, located in the Guerrero state of Mexico. It is an 8-km (5-mile) long roadway that starts at the Icacos neighborhood, heading toward Acapulco’s airport, crossing a drill-and-blast tunnel that is 3,160 m (10,350 ft) long under Veladero Park, a mountainous area. The tunnel overburden reaches a depth of 380 m (1,250 ft) approximately at the central point of the horizontal alignment, and continues with a 4-km (2.5-mile) long elevated road to connect to the existing Viaducto Diamante toll road (Fig. 1).Tunnel construction has already been finished using two portals for drilling and blasting operations; Brisamar Portal on the west side and Cayaco Portal on the east side (Fig. 2).Geometric dataOnly two main excavation cross-sections were considered in the executive design. The first one corresponds to the running tunnel for a three-lane vehicle section, with crosssection areas between 120 and 130 m2 (1,290 and 1,400 sq ft) taking into consideration different geological and geotechnical conditions to be encountered (Fig. 3).The second one corresponds to eight emergency bays, each one 50 m (164 ft) long, laid down within the tunnel outline, located at 400 m (1,312 ft) from each one with excavation cross-sections between 156 to 169 m2 (1,680 to 1,820 sq ft), in accordance to geological and geotechnical conditions to be encountered (Fig. 4).The tunnel’s horizontal alignment is completely straight, having a small curve within the vertical alignment on Cayaco portal, because there were some differences in levels when tunnel excavation started. Tunnel slopes were designed in such a way that rainwater does not run down into the tunnel at any time."

Jan 3, 2018

By L. F. Reinartz

ANOTHER year has rolled by. We are twelve months further away from the start of the depression and. therefore that much nearer to recovery. The accumulated needs and wants 'of our lame, virile population are ready to burst their bonds as soon as confidence returns and credit is stabilized. The steel industry has been harassed by uncertainty of the Government's attitude toward organized labor's de¬mands, and irregularity in volume of production. Steel labor, if left to its own devices, would in most instances, march shoulder to shoulder with the management of steel plants in their effort to pull the industry nut of the ?red.? Cooperation between management and men has improved considerably during; the year.

Jan 1, 1935