Search Documents

By A. McLean, M. Iwase, K. Wakimoto, K. Katogi

For many decades control strategies have been based upon samples taken from liquid steel, molten slag and gas phase as well as from solid products. Because of recent developments in the areas of dynamic control models, artificial intelligence and expert systems, there is an increasing incentive to develop diagnostic sensors, which permit in-situ rapid determinations of concentrations of various elements in molten steel. In this paper, an overview is given on recent developments in the areas of sensors for use in ferroalloy and steel production. Particular emphasis will be given on (i) innovative application of sensors for on-line determinations of dissolved elements, Si, P, N, H and Cr in molten iron and ferroalloys, (ii) evaluation of inclusions in liquid metal and (iii) rapid determinations of slag compositions.

Jan 1, 2004

By Jim Frazier

Tradition has often dictated low design load stresses on piles. Such traditions often developed prior to modern static or dynamic pile testing methods and perhaps result from a few limiting situations. These low stress limits were then broadly applied, even in cases where the piles could carry substantially higher loads. With sufficient testing to prove the design, higher design loads may present significant overall savings to the project owner. The cost of the testing then becomes an insignificant cost compared to the potentially great benefit of increased pile loadings. To confirm higher load possibilities for driven piles, the pile is tested either statically or dynamically. Further savings and increased testing efficiency result from remote dynamic pile testing. This paper presents a project where design stresses were considerably increased as a result of additional testing and use of remote dynamic pile testing equipment.

Jan 1, 2002

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Froth depth or interface level is an important control variable in column flotation which can influence both grade and recovery. A common method of locating the level is based on sensing the hydrostatic pressure at one or more points along the column. The level position is then calculated from these pressure readings using an equation which includes the bulk density in the froth and bubbling zones. The precision with which the level is detected depends on how well these density values represent both zones. The calculation of these bulk densities from theoretical considerations is not possible and, therefore, the practice is to estimate them by calibration. Unfortunately, the calibration parameters often do not report the level with an acceptable accuracy. A portable conductivity probe has been developed to detect the position of the interface from conductance measurements across the interface. The location of the interface corresponds to the position where a large change in conductance is observed, which is primarily a consequence of the difference in gas holdup between the bubbling and froth zones. This probe can be used to detect the position of the interface to an accuracy of± 5 cm. The probe can be used while the column is in operation, which allows the on-line calibration of the level detection system. Results obtained in its application in a pilot-scale column (0.91 min diameter) are described.

Jan 1, 1989

By Dale S. Preece, Lee M. Taylor

Accurate computer prediction of the muck pile produced by a conventional blast requires modeling of the physics that occurs during the rock motion phase of a blast. The ability to predict the motion and the subsequent muck pile can have a significant economic impact on the mining industry.

Jan 1, 1990

By A. M. Ramalho

In the synthesis and sintering processes to obtain superhard materials, such as diamond and cubic boron nitride, deformable ceramic capsule is used as gasket to transmit and support the required high pressures and high temperatures, HPHT. The ceramics materials for these capsules should have special physics and chemical characteristics such as refractoriness, shear strength and compressibility. In this work, Bridgman?s anvil made of hard metal or speed steel was used to characterize some ceramics materials in terms of their maximum compressible thickness. Tests were also performed with different resin polymers used as binding mixture with ceramics powder. Chemical analyses and investigations through scanning electronic microscopic (SEM), X-ray and real tests for the synthesis of diamond were also performed. The results showed that local Brazilian calcite can be successfully used in the manufacture of HPHT gaskets.

Jan 1, 2006

By Michel Fontaine, Bruno St-Cyr

"The mission of the CENTRE DE RECHERCHE INDUSTRIELLE DU QUEBEC (CRIQ) is to stimulate economic development by guiding businesses in their pursuit of innovation.With a comprehensive approach to their needs, CRIQ provides businesses with expertise based on the most recent developments and insights in the fields of:Research and Development ServicesAutomation and production processesDevelopment of industrial equipmentEnvironmental biotechnologiesTesting and Product Qualification Services Industrial and Technological Information ServicesConsultancy and competitive intelligence servicesIndustrial information bankStandardization ServicesElaboration of standards and product certificationSystems registrationEXPERTISE COMPETENCE, INNOVATIONSince its founding in 1969, CRIQ has been involved in over 100,000 projects. The results of its research and development services have enabled it to build over one hundred pieces of equipment, almost all still in operation today. CRIQ has been and remains the driving force of innovation and expertise on the industrial scene, offering highly competitive solutions to a clientele from numerous industrial sectors.CRIQ became a crown corporation operating on a commercial basis on June 30, 1997. This change in its corporate structure has enabled it to put a marked emphasis on trade and implement an array of new operational practices.The formation of marketing companies with private partners, the opening up to corporate business and international markets, the new directions for internal research and the strengthening of its marketing component are among the activities CRIQ has initiated over the last fiscal year to finally reach its cruising speed."

Jan 1, 2000

By A. M. Neale

Kriel Colliery has experienced some sub-standard blast results on the overburden. Blast results are considered poor when the fragmentation is too big, back break into the new highwall, capping is experienced and/or excess overburden material is thrown into the void. Poor blasting leads to lower productivity, equipment breakdowns, and poor drilling and blasting results on the adjacent blast, contamination of coal or loss of coal. A simulation was developed in Microsoft Excel to model blasting results while changing various parameters. From the simulation results, it could be seen that a change of blast design could be beneficial. As an example, smaller drilling patterns were simulated (10 m x10 m to 8 m x8 m, and 8 m x8 m to 7 m x7 m in Pit 5 and Pit 6 respectively) in combination with changes in explosives (P700 emulsion vs. ANFO) and drill bit diameter (311 mm vs. 251 mm). The results show that each of the options has a specific scenario that will be most beneficial to the mine. These results are quite specific and subject to variable inputs. The purpose of the example is to demonstrate how the simulation can be used as a tool to asses blast design variations.

Jan 1, 2010

By A. K. Majumder

The multi-gravity separator (MGS) is a novel piece of equipment for the separation of fine and ultra-fine minerals. However, the published literature does not demonstrate its use in the separation of coal fines. Therefore, an attempt was made to study the effects of different process variables on the performance of an MGS for the beneficiation of coal fines. The results obtained from this study revealed that among the parameters studied, drum rotation and feed solids concentration play dominating roles in controlling the yield and ash content of the clean coal. Mathematical modeling equations that correlate the variables studied and the yield and ash contents of the clean coal were developed to predict the performance of an MGS under different operating and design conditions. The entire exercise revealed that the MGS could produce a clean coal with an ash content of 14.67% and a yield of 71.23% from a feed coal having an ash content of 24.61%.

Jan 1, 2007

By A. E. Lewis

Particle morphology is a term that is used to describe the overall external shape and appearance of particulate solids. From the physical point of view, a precipitated solid is characterized primarily by the size and morphology of the particles (Sohnel andGarside, 1992). If the morphology of the crystal structures is to be related to the processing conditions, then the morphologies need to be quantified in some way. This can be achieved by using surface area measurements as well as fractal dimensions. The key idea is that rugged and indeterminate systems can be described by using a fractional number that describes the ruggedness of the system (Kaye, 1989). In other words, when the complexity of a structure, such as an agglomerate, increases with increasing magnification, it is useful to employ fractal dimensions to describe the structure. Fractal geometry proposes that, instead of attempting to measure the length of an irregular boundary, the rate at which the length of the boundary approaches infinity with increasing resolution should be calculated. Cross-sectional profiles of rugged particles can thus be quantified using the fractal dimension, and a measurement of the ruggedness of the morphology obtained. One of the additional uses of measuring the fractal dimension is that the measured value can be related to the physical properties and formation characteristics of the particle (Kaye and Trottier,1995). The morphology of nickel crystals was quantified with fractal dimension calculations of particle cross-sections. Particle cross-sections were obtained by mounting the particles in resin and polishing back. These were then photographed using Scanning Electron Microscopy and the resulting profiles analysed using the structured walk technique.

Jan 1, 2001

By J. Wagner, P. Eger

Although lifetime estimates for sulfate reduction based on total substrate carbon typically range from 20 to 30 years, field and laboratory experiments showed that rates of sulfate reduction decreased over time as readily available organic material was consumed. When the rate of acid input exceeded the rate of sulfate reduction, alkalinity was removed from the substrate, pH decreased and metals increased. Output pH increased from 4 to over 6 after the system was shut down for several weeks and the rate of acid input was reduced. Successful long term treatment requires a design based on the input pH and the long-term organic decomposition rate.

Jan 1, 2001

By Gregory J. Chekan

This Bureau of Mines report presents three methods for designing bulkheads to impound water underground: (1) thin and thick plate design; (2) South African plug design; and (3) single and double bulkhead seal design. Related areas critical to the long-term effectiveness of underground water impoundments are also addressed. These include bulk-head anchorage, concrete specifications and placement, the grouting of permeable strata, and the sizing of barrier pillars. A case study involving hydrostatic tests conducted on a single bulkhead seal constructed in the Safety Research Coal Mine of the Bureau's Pittsburgh Research Center is presented in an appendix.

Jan 1, 1985

By R. B. Alke

Request to Mine Beneath Bridge The Jabs Run Bridge is a reinforced portland concrete arch filled bridge located on WV Bouts 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Pig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old Wing been built in 1929 and is owned by the Department (WV Department of Highways).

Jan 1, 1984

By Nikhil Dhawan

Electronic waste (e-waste) is a collective name given to discarded electronic devices such as Television, Cellular Phones and Personal Computers. Among the heterogeneous metals present in the e-waste are the base metals: copper, aluminium, nickel, tin, zinc, iron and precious metals: gold, silver, palladium, platinum apart from several hazardous and halogens metals. Hence there is a need to recover these metals from electronic scrap by recycling and then re-use, which can meet large amount of metals demand. Hydrometallurgical processing was employed for the recovery of metals from television printed circuit board (TV PCB). Different lixiviants such as hydrochloric acid, Sulphuric acid, and nitric acid were used to understand the dissolution behavior of copper, iron and lead present in the TV PCB. Effect of increasing concentration of nitric acid was also studied. Selective recovery of tin over 95% in the form of tin oxide was precipitated. The precipitated tin oxide was identified by X-ray diffraction technique. Tin oxide of purity more than 99.9% was obtained.

Jan 1, 2009

By Russell R. McLellan

As part of an effort to develop new or improved placer mining technology in the Tertiary gold-bearing channel gravel of northern California, the Bureau of Mines conducted investigations at the old Badger Hill placer mine in Nevada County, Calif., to collect data and information regarding drilling and sampling methods and deposit characteristics. Sampling studies involved the collection and processing of 400 tons of large-and small-volume samples from drill holes, underground workings, surface pits, and blasthole rounds. A total of 355 samples averaging 2,296 pounds per sample provided reasonably accurate data for analysis of the gold distribution. These studies indicated that the bulk of the gold is within 40 feet of bedrock in stacked, lenticular zones of cemented gravel that are largely confined to the relatively narrow, meandering course of the deepest portion of the bedrock channel. Drilling studies involved the testing of truck-mounted rotary, buckett and vibratory drills, none of which proved to be a completely versatile tool for sampling quickly and reliably both consolidated and unconsolidated gravel..

Jan 1, 1974

By Hamid Maleki

Having developed a methodology for estimating mining-induced seismicity resulting from slip along geological discontinuities in 2003, in this paper, the importance of measurements are high-lighted in the study of caving and seismic source mechanisms as applied to mine designs. Geotechnical data is analyzed from four case studies to address cave condition, load transfer, and potential effects on stability and resource recovery in four Utah mines using measurements and observations conducted over the last three decades. Cave conditions are evaluated on the basis of measurements in the gob of a western U.S. operation mining under the massive Castlegate Sandstone and indirectly using the results of measurements and boundary-element modeling at panel boundaries at a mine where strata behave elastically. Together with subsidence measurements and microseismic monitoring, regional caving and load transfer in multiple-panel extractions are addressed while the effectiveness of barrier pillars in reducing stress and seismic response where mining under massive stratigraphic units is analyzed using measurements and three-dimensional computer modeling.

Jan 1, 2006

By J. Moore, D. Gault, R. V. Lugn

Impact of small projectiles with velocities between 0.9 and 7.3 km per sec on basalt produce craters chiefly by the ejection of fragments. Weight-size distributions of the ejecta are linear for part of the size range of the fragments. Cumulative weight-size distributions of the ejecta from different craters vary because of erratic formation of large fragments and a large percentage of ejecta below 0.1 mm. In the range of velocities studied, the crater depth is approximately proportional to the 0.75 power of velocity of the projectile. This relationship may represent a transition regime between the fluid impact regime and the undeformed projectile impact regime. The volumes per unit of projectile energy of the craters produced are comparable to those reported for lower speed projectile impact and drill bits. An experimental investigation of projectile impact on rock is being conducted jointly by the Ames Research Center of the National Aeronautics and Space Administration and the U.S. Geological Survey. Projectiles are launched with light-gas guns at the Ballistics Range of the Ames Research Center. The craters and ejecta produced in these experiments are being studied by the U.S. Geological Survey. Steel, aluminum and polyethylene projectiles weighing from 0.25 to 0.015 g were accelerated to velocities of 0.88 km per sec (2,900 fps) to 7.3 km per sec (24,000 fps) with a light-gas gun, using hydrogen as the propellant medium. Projectiles impacted the targets normal to plane rock surfaces in an atmosphere of air with a nominal pressure of 25 to 50 mm of mercury. The metal projectiles were mounted in supporting four-piece nylon sabots, which guided the projectiles down the launching tube. After launch, aerodynamic drag acted to separate the sabots from the projectiles. Impact velocities were determined with time measurements and spark photographs of the projectiles in flight. Ejecta were collected in lucite and aluminum containers placed around the target block. A small hole in the containers permitted projectile entry. Impact of projectiles of the size employed produced craters in the rock targets chiefly by ejection of fragments. The craters are small, roughly conical depressions with crushed and intensely fractured rock at the bottoms of the depressions. The ejecta are composed of pieces of the projectile and rock fragments ranging in size from a few tenths of a micron or less to several centimeters in maximum dimension. In this paper, the structural features of the craters, the weight-size distributions of the recovered ejecta, and crater depth and crater volume relationships are described. DESCRIPTION OF CRATERS Typical craters (Fig. 1) produced by experimental projectile impact in basalt are shallow, wide base

Jan 1, 1963

By A. K. Mukherjee

The roles of pulsating mechanisms such as the amplitude and frequency of the jig cycle are well established in jigging. Also well established are the roles of the size ratio and the volume fraction of the feed. In iron ore beneficiation plants, these process parameters are optimized to achieve the highest efficiency. However, the role of one of the more important feed characteristics, the liberation characteristic of the feed, has not been studied in detail. Evaluation of the liberation characteristics is difficult because the required washability test is not viable for iron ore feed. In this paper, a new method is proposed in which the liberation characteristics are measured through a separation efficiency value. In the new evaluation method, jigging parameters such as amplitude and frequency of the jig cycle are optimized from the fundamental understanding of the process dynamics and feed characteristics such as size distribution. Then, feeds with different liberation characteristics are tested to evaluate the liberation characteristics of feed in jigging.

Jan 1, 2008

By O. Acaroglu

Selection of the most suitable roadheaders (boom type tunnelling machines) for the galleries/tunnels to be excavated in certain rock and under known project conditions is important for avoiding problems during application. This research utilized a multiple attribute decision-making method and studied how this will be applied for the selection of boom-type excavation machines. The Cayirhan Coal Basin was used for selecting roadheaders using the analytical hierarchy process, which is one of the multiple attribute decision-making methods. To conclude, this study reveals that decision-making methods can be used in the process of selecting roadheaders for the excavation of galleries. Keywords: roadheaders, multiple attribute decision-making, analytical hierarchy process.

Jan 1, 2006

By B. B. Broms

Embankment piles are common in the Scandinavian countries (Kjellman, 1940) and in Southeast Asia as support of fills, light structures, bridge abutments and deep excavations (Eide, 1968) as described in the following. Untreated timber piles are often used for light structures and shallow fills when the ground water level is high since they are inexpensive and readily available. When the applied loads are relatively high precast concrete piles and steel piles are preferred. DESIGN CONSIDERATIONS Embankment piles carry the load from a fill or a struc-ture either through skin friction along the sides of the piles (Fig. 1a) or through a precast concrete slab or through pile caps at the top of the piles (Fig. 1b). When the load is carried by skin friction it is often economical to use small diameter timber piles because of the large surface area (Asplund, 1939). For precast concrete or steel piles concrete caps are used to transfer the load to the piles due to the relatively high capacity of the piles since the skin friction resistance alone is not sufficient to transfer the load to the piles.

Jan 1, 2010

By Charlie Wyche

The British Solomon Islands Protectorate continued developmental work on bauxite deposits on the Islands of Rennell and Vaghena. A feasibility study was completed by Mitsui Mining & Smelting Co., Ltd., and Pacific Aluminum Ltd. (a subsidiary of Conzinc Riotinto of Australia Ltd,), and negotiations with the Government were in progress. The Government will receive a 25% share if the project is realized. It was estimated that the Islands contain 60 million tons of bauxite with an alumina content of 45% to 50%.

Jan 1, 1980