Search Documents

By P. S. B. STEWART

As part of a continuing study of mechanisms of breakage, the grinding at Nairne Pyrites Pty. Ltd. was traced by the addition of barytes and the results compared with parallel small scale laboratory tests. It was confirmed that the same basic mathematical functions described the behaviour of the full scale ball mill as those established in the small scale mill. However, an additional classification function was required to define the behaviour for the rod mill and was evaluated as a function of size from the experimental data. The classification and grinding of the pyrites ore was assessed from steady state size distributions around the circuit.

Jan 1, 1971

By Guillermo Velarde

Dado que la flotación seguida por la fundición/ refinación es la única vía de procesamiento del cobre, se buscó una alternativa que trate con suficiencia los sulfuros de leyes marginales dentro del CUT-OFF de una concentradora. En ese sentido, el presente texto señala que la energía solar se convierte en una herramienta que ayuda a lixiviar minerales con poca pirita y obtener una temperatura de proceso que magnifica la recuperación del cobre en especial de la calcopirita, etc. Asimismo, la influencia cuantitativa de la temperatura en la recuperación de los sulfuros primarios, transicionales y secundarios de cobre, la velocidad de calentamiento de la pila, las temperaturas de proceso que puede alcanzarse, las pérdidas de calor en el periodo no soleado del día, el balance térmico de la pila y otros indicadores económicos de viabilidad, etc. son presentados como resultados de pruebas diversas a nivel de laboratorio e industrial.

Oct 21, 2015

By M. Tangstad

Keywords: Pyrometallurgy, ROMA, Norway, furnace, fines The ROMA project is a competence project on optimizing the usage of raw materials and energy in the ferromanganese, silicon, and aluminium industries. One of the items investigated in this project is the effect of fines on the furnace, and the usage of agglomerates versus lumpy ore. From lab-scale experiments it is shown, that for the charge to agglomerate in the furnace, the charge has to be exposed to a temperature higher than about 1200°C, independent of fines content. The fines less than 1 mm also showed higher agglomeration properties, compared to 2?4 mm, which showed no agglomeration property at all. The properties of agglomerates are very dependent on the pre-treatment of the agglomerate. Sinter and pellets, which have been heated to high temperatures, show a better strength, but also a lower CO reactivity. Sinter also shows a lower melting temperature compared to the ore.

Jan 1, 2011

By D. M. Wyslouzil

"This paper was prepared for presentation at the 16th Canadian Mineral Processor's Annual Meeting, Ottawa, Ontario, Jan. 17 to Jan. 19, 1984.This paper gives an account of the development of treatment procedures for the differential flotation of refractory copper-zinc ores. Special references are made to the effectiveness of various zinc depressants and their combinations.Studies carried out on refractory copper-zinc ores demonstrated that conventional zinc depressants such as cyanide and zinc sulphate were not particularly effective when secondary copper minerals were present in the ore; the flotation activity of sphalerite was enhanced in the presence of cyanide.Among the various zinc depressants evaluated, the following depressant combinations were found most effective: Zn(OH) 2-S02 , 802-CaO, Na2S-Na2S03-S02, Na 2 S-S02 and Na 2S-S0rDS22.The practical application of any of these systems depends on the type of ore treated and other conditions such as pH, levels and points of collector and depressant additions.In this paper the effect of each depressant combination on different ores is described with reference to the selection of collectors."

Jan 1, 1984

By Victor C. Bryan

One of the most sought after answers in any consideration of blasting activities relative to mines and quarries is how to safely and efficiently use explosives. While that discussion might be relatively straightfonvard in a “site specific” situation. it becomes more complex when viewed from a broad geographic perspective. Such is the case in considering the operations of one United States producer of crushed stone with surface and underground mines spread over a thirteen state area. Differing geologic environments set conditions that dictate to the blaster as now specifically to get optimum results from the blast hole. This treatise is a discussion of the various methods, materials, and principles used in conducting such blasting operations.

Jan 1, 1991

By T. Güyagüler, A. Güngör

Labour protection, that is prevention of occupational disease and reduction in the frequency of accident, has always been a matter of major concern of mining industry. Management and the government should promote and maintain high safety standards through some measures to reduce accident frequency and occupational disease. This can be achieved by using the science and technology for improving the working conditions, educating workers and managers about accidents and prevention techniques. The detailed analysis of an accident requires knowledge of many factors such as location, time, type, cost of accident, victim, nature of the injury, personal and environmental factors etc. that can be obtained from the standard coded accident report form. There is a need to prepare safety data in a common format to produce a common safety reporting system and ‘Occupational Health and Safety Management Tool’ is being designed to manage this by using database and Internet technology. Precautions should be taken according to results from database queries by providing comprehensive and accurate national data. To have an accident is unfortunate, however, to have an accident and learn nothing from it is unforgivable. Keywords: Occupational health and safety, Accident report form, Accident database, Occupational diseases and accidents, Safety reporting system.

Jan 1, 2003

Peñasquito is Mexico's largest gold producer, consisting of two open pits - Peñasco and Chile Colorado - containing gold, silver, lead and zinc. Over the next three years, mining activities in the pit are expected to be focused on lower grade ore in the upper parts of the Peñasco pit while stripping is emphasized to ensure an economically optimal pit shell design to maximize the net asset value of the operation. By 2019, Peñasquito’s gold production is expected to benefit from an improvement in mined grades as it recommences mining higher grades at the bottom of the Peñasco pit and significantly enhanced metallurgical recoveries with the planned completion of the Pyrite Leach Project ("PLP").

Jan 1, 2017

By J. Kempken, R. Degel, J. Kunze, R. König

The FeNi technology is currently dominated by high-power submerged arc furnaces, often designed as smelter as "two-inline-solution". To achieve the intended high efficiency, state-of-the-art design in good correlation with ores and reductants and an integrated layout of the whole plant is of great importance. An introduction will be given to general aspects in the production FeNi, plus a detailed overview of design principles for large FeNi smelters and finally some examples of innovations and research projects concerning Fe-Ni.

Jan 1, 2007

By J. R. Ross

A reconnaissance for sources of scandium and a metallurgical investigation of recovery methods for byproduct scandium from uranium mill solutions were conducted by the Bureau of Mines. The work on scandium was undertaken to obtain information on domestic resources and to explore and develop recovery procedures in consonance with the Bureau's long-range program for conservation and wise utilization of mineral resources. The element scandium is widely distributed in the earth's crust in trace amounts, but it seldom occurs as an important constituent in any mineral. An exception is thortveitite, (Sc,Y)2 Si207) a rare mineral that contains various amounts of scandium and yttrium and may contain up to 42 percent scandium oxide (SC203). Knowledge of the chemistry of scandium has expanded rapidly in recent years (1, 4, 9)4 but only fragmentary information is available about the metal because it is still largely a laboratory curiosity without established uses (2, 3). A recent study shows some of the physical proper-ties of the metal are (1) density of 3.05 grams per cubic centimeter) (2) melting point of 1,540° C, (3) hexagonal close-packed structure) (4) hardness of about 50 Brinell (500-kilogram load), and (5) an alloy behavior similar to yttrium and rare-earth metals (2). The price of $2,850 a pound for scandium oxide of 99.9 percent purity and $2,700 a pound for oxide of 99 percent purity reflects the scarcity and complex chemistry of the element.

Jan 1, 1962

By H. Ogasawara

Information on rock stress is important for safe mining in seismically active ground. On a major gold mine, a few tens of crews are continuously conducting geological drilling with small pneumatic machines. However, stress measurements are not often carried out in South African deep-level gold mines. One of the reasons is the drilling diameter that overcoring requires, which is much larger than the diameters used in regular geological drilling, e.g. Boart Longyear Metre Eater, which drills A[O] or B[O] holes. Larger diameter holes result in slower drilling advance, more load in transportation and handling at sites, and higher cost. In order to enable overcoring in BX size (60 mm diameter), we modified the compact conical-ended borehole overcoring (CCBO) technique that has been suggested by International Society for Rock Mechanics (ISRM) and was originally designed for NX drilling (76 mm diameter). With a single overcoring, the 3-D stress tensor can be determined. We tested this modified method at a depth of about 3 km at Moab Khotsong mine in South Africa. We worked with drilling crew who usually work at geological drilling with the Metre Eater. In January 2011, we tried using regular geological drilling tools (a sequence of a normal BX bit, reamer, and rod) without success. In August and September 2011, introducing stabilizers and thin BX bits, we succeeded. We could complete a cycle of procedures necessary for an overcoring, including shaping the borehole-end conically, glueing a 16-element strain cell, and overcoring, within 2.5 hours. Only 10 cm overcoring is needed, which increases the chance of successful overcoring in heavily fractured conditions. This modified method is suitable for up-dip holes to depths of 10-15 m from tunnels, and has the potential to be widely used at the initial stage of geological exploration drilling at many localities.

Jan 1, 2012

By Donald E. Ralston

The Huntsville study area in northeastern Alabama consists of Jackson, Limestone, Madison, and Marshall Counties. Major emphasis was placed on the Huntsville urban area in Madison County to analyze the relationship of urban growth and the minerals industry. Huntsville was delineated into its component urban, suburban, and rural parts for 1964, and the primary area of growth was predicted for 1990. Population estimates were made for the four-county area as a unit and Madison County separately, and projected to 1990. Demand estimates for crushed stone and sand and gravel were made for the same area units and projected to 1990. Analysis of quarry sites in the Huntsville area was made for the present and for the future. The mineral operations of the study area are all located in rural areas; in the case of Huntsville, the mineral sites are located in areas defined as "rural" in the component urban-suburban-rural system. The operations outside Madison County can expect to have minor problems with urban encroachment, while those operations in Madison County can expect major problems associated with urban growth and development. Some of the problems associated with limes tone production can be reduced if producers invest in capital equipment that will reduce the nuisances inherent in this activity. Although urban expansion endangers some quarry operations in Huntsville, topographic and political restrictions which prevent urban expansion can effectively shield quarry operations for some time.

Jan 1, 1970

By A. Noble, R. Q. Honaker, J. Werner

Recovery of rare earth elements (REE) from coal-related resources has recently received significant interest due to supply concerns and their key roles in critical industries and defense-related technologies. An integrated flowsheet consisting of sorting, crushing/grinding, physical separation, acid leaching, solvent extraction, and selective precipitation was designed to achieve continuous production of rare earth products from various coal-related resources such as coarse refuse and acid mine drainage. A pilot plant was constructed that enabled continuous testing of the circuitry on a range of different coal-based feedstocks. Despite achieving significant success in producing high-grade rare earth oxide products, low REE recovery values and high operational costs necessitated a re-evaluation of the process flowsheet. This article describes the circuitry improvements that were based on both laboratory and pilot plant test results. Roasting as a pre-leach treatment was found to significantly improve the leaching rate and overall REE recovery values. After roasting West Kentucky No. 13 and Fire Clay coal refuse materials at 600 °C, REE recovery increased by 60 and 40 absolute percentage points, respectively. Rare earth concentration in the pregnant leachate solution (PLS) was increased to around 700 ppm prior to solvent extraction using a staged precipitation method. REEs in the precipitate were re-dissolved, purified, and extracted from the PLS using solvent extraction and selective precipitation to values of around 80%. As a result of the improvements, chemical consumption in the acid leaching and solvent extraction processes was significantly reduced. A techno-economical assessment of the improved flowsheet indicated significant commercialization potential.

By Roy McKinstry, Mark Rantapaa, Thomas Bolles

"More efficient drilling and blasting techniques have shown measurable improvements in throughput at the Barrick Goldstrike wet grinding mill.A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas participated closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of improving throughput in future years, despite the projected harder ores. Plant studies were conducted to determine if adjustments to drilling and blasting could positively influence throughput. At the Goldstrike mill the greatest opportunity from the D2M initiative is realized on the hardest ore. Grinding throughput for softer ore, <15 kWh/st, can meet or exceed the downstream pressure oxidation requirements. Grinding throughput for harder ore, >15 kWh/st, is limited by the SAG milling capacity. Better fragmentation in the D2M ore, as demonstrated by image analysis, increased throughput 5% to 10% (25 to 50 stph) compared to the standard mining methods.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of:1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots.2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy.3) Improved distribution of the explosives by decreasing pattern spacing.INTRODUCTIONThe Barrick Goldstrike Open-Pit group, along with the Process division, began experimenting with novel blasting technology and techniques to improve mill throughput in the spring of 2001. A series of tests were developed to determine if fragmentation and ultimately mill throughput could be influenced by optimizing the drilling and blasting program in known"

Jan 1, 2004

By R. Simkus, J. K. Gowans

Polaris Operations, a Cominco Ltd. lead-zinc mine, is located on Little Cornwallis Island, Northwest Territories, at Latitude 75°23' N and Longitude 96°75' w. When the Polaris Mine went into operation in late 1981, it became the world's most northerly base metal mine.The Polaris Concentrator, housed in a unique process barge, is a basic lead-zinc concentrator where flotation is used to produce the lead and zinc concentrates.The paper describes the ""coarse lead"" flotation feature incorporated in the concentrator flowsheet and describes the start-up problems and continuing operation of this circuit.

Jan 1, 1984

By P. A. Mahanwar

Flyash were melt mixed with nylon 6 at a 30wt% concentration. TYZOR® TPT, a coupling agent, was used to facilitate the link between filler and matrix. The morphological characterization, using SEM, revealed sufficient matrix residue on the filler surfaces thus confirming the strong interfacial bonding between the filler and the matrix on treating. Tensile, impact and the flexural properties of the composites were also improved with the incorporation of coupling agent. As flyash particles tend to impart a grayish color to the plastic, TiO2 pigment was employed to make the formulations aesthetic. The pigment was added to the filled system in 0.1, 0.5, 1.0, 1.5, 2.0 wt/wt ratios. Scattering of incident light and spectral reflectance was higher for smaller particle size flyash. Moreover an increase in the scattering with increase in pigment concentration indicates better dispersion of the pigment, which again is due to the presence of coupling agent.

Jan 1, 2006

DESCRIPTION OF OREThe ore consists, in general, of a very finely grained mixture of sphalerite, galena, and pyrite, with a gangue of quartz and schistose material, and contains about one ounce of silver to the unit of lead.Minor minerals are chalcopyrite, tetrahedrite, and ruby silver. The amount of gangue within the ore-bodies themselves is usually less than 20% of the weight of the whole. The ore is banded in a way that corresponds to the structure of the original schists, and is by no means uniform in composition-at one point, for example, blende may predominate, and a few feet farther on the body may become highly pyritic.Owing to the intimate association of the mineral constituents of the ore, it is very difficult to separate them from one another.Although this remark applies to ore from all parts of the field, the difficulty is particularly noticeable with Rosebery ore, the minerals of which are more intimately mixed, and are of smaller grain size than are the minerals of the Hercules ore.To effect a reasonably clean separation, it is necessary to grind the ore so that 90% passes a 200-mesh I.M.M. screen. Microscopic examination of the crushed product shows that 85% of the minus 200-mesh material is less than 30 microns in diameter, or, in terms of screen sizing, is minus 400 mesh. Particles under 30 microns are found to consist, of one mineral only, but in particles over this size separation has not always been effected. For instance, it is known that part of the galena and of the pyrite in the zinc concentrate is associated with sphalerite, and that part of the galena in the mill residue is associated with pyrite. There is only slight association between the minerals in the lead concentrate.

Jan 1, 1927

By Reid K. J, Restarick C. J

The breakage and flow characteristics of quartz, ground as a minor constituent with calcite in a continuous wet ball mill, have been determined by carefully controlled grinding tests.A mathematical model, combining the simple functions which describe these characteristics, has been used to predict both steady state and non steady state results.The calculated results are compared with experimental data.

Jan 1, 1966

The purpose of this paper is to describe briefly the clean-up procedure adopted at the treatment plant of Paringa Mining &amp; Exploration Co. Ltd. at Kalgoorlie, Western Australia.A clean-up is carried out at the end of each four-weekly period, and all figures subsequently quoted are taken from a summary of the results of the eight periods ending 8th April, 1941.STRAKING AND AMALGAMATIONOf the total gold won 22&#183; 77 per cent. is recovered by straking and amalgamation.The discharges of both the primary and secondary ball mills are pumped over a common set of five ten feet long by three feet wide straking tables, set at an angle of 10 degrees, before passing to the 14 ft. diameter by 30 ft. by 8 ft. Dorr bowl classifier.This classifier is in closed circuit with both of the ball mills, hence the whole of the circulating load of the fine grinding circuit, which approximates to 800 per cent., is required to pass over the straking tables. For convenience in handling, corduroy cloths are used in lengths of 5 feet, and are picked up and replaced by clean cloths at four-hourly intervals. The avaHable straking area provided is, therefore, 900 square feet, or approximately 3&#183;30 square feet per original ton per 24 hours. The density of the pulp passing over the tables is about 54 per cent. solids, the area provided per ton of pulp per 24 hours being approximately o&#183; 2() square feet. Washing of the corduroy cloths is carried out on the day shift only, about 800 lb. of strake concentrate being obtained daily.This concentrate is sluiced from the washing trough on the elevated straking floor to the 4 ft. by 2 ft. diameter amalgamating barrel located in the gold room below.The barrel is of standard design and is rotated at 25 r.p.m. It is charged each day at 4 p.m., and grinding of the strake concentrate at approximately 70 per cent. solids is continued until 8 a.m. the following day. The barrel is then stopped, and the contents generously diluted with water, and after a few minutes rotation some of the slime is carefully poured off through the small discharge hole. This dilution and decantation is repeated until a good deal of the valueless slime has been removed.A further quantity of strake concentrate is then charged to the barrel, which is allowed a further 16 hours grinding period. After again diluting and decanting, approximately 25 lb. of mercury and 15 lb. of lime are added to the charge, which is then given an amalgamation period of 2 hours before cleaning up.By the process of grinding, diluting and removal of slime by decanting...

Jan 1, 1941

By A. Noble, R. Q. Honaker, J. Werner

Recovery of rare earth elements (REE) from coal-related resources has recently received significant interest due to supply concerns and their key roles in critical industries and defense-related technologies. An integrated flowsheet consisting of sorting, crushing/grinding, physical separation, acid leaching, solvent extraction, and selective precipitation was designed to achieve continuous production of rare earth products from various coal-related resources such as coarse refuse and acid mine drainage. A pilot plant was constructed that enabled continuous testing of the circuitry on a range of different coal-based feedstocks. Despite achieving significant success in producing high-grade rare earth oxide products, low REE recovery values and high operational costs necessitated a re-evaluation of the process flowsheet. This article describes the circuitry improvements that were based on both laboratory and pilot plant test results. Roasting as a pre-leach treatment was found to significantly improve the leaching rate and overall REE recovery values. After roasting West Kentucky No. 13 and Fire Clay coal refuse materials at 600 °C, REE recovery increased by 60 and 40 absolute percentage points, respectively. Rare earth concentration in the pregnant leachate solution (PLS) was increased to around 700 ppm prior to solvent extraction using a staged precipitation method. REEs in the precipitate were re-dissolved, purified, and extracted from the PLS using solvent extraction and selective precipitation to values of around 80%. As a result of the improvements, chemical consumption in the acid leaching and solvent extraction processes was significantly reduced. A techno-economical assessment of the improved flowsheet indicated significant commercialization potential.

By Peter L. Sheehan, David A. Fawcett, Dennis C. Martin

"Smoky River Coal Limited has successfully completed a major program involving the pattern rock anchoring of a high, steeply dipping footwall slope. The slope dips at approximately 65 to 70 degrees to the north, is benched for the upper 200 feet, is supported with rock anchors for another 240feet, and is unsupported at the pit bottom. In addition to the height and steepness, several structural features including shears, rolls and stratigraphic pinch- outs complicate footwall stability.This paper presents an overview of the project with descriptions of the engineering geology and footwall design, anchor installation, instrumentation and monitoring and a cost summary.IntroductionSmoky River Coal&apos;s mines are located in the foothills of the Rocky Mountains near Grande Cache, Alberta, approximately 200 miles west of Edmonton. The Smoky River coal leases were initially developed in the late 1960s and, except for minor shutdowns, have been in continuous operation since 1969 producing a low volatile metallurgical coal, mainly for the export market. Initial coal production was from underground mines; sur face mining started in 1971, and a large surface mine, No.9 Mine, was opened in 1974. Since that time, a number of open pits have been mined within the No.9 Mine area. Surface mining is by conventional shovel-truck method s with the use of a backhoe for mining the narrow pit bottoms.Coal recovery is mainly from the No.4 seam, which has a typical unstructured thickness of 20 feet. The most attractive opportunities for open-pit mining exist in areas of over thickening of the coal seam in the hinge zones of synclines and anticlines and in dip-slope situations. The mining of the more structurally complex pits and steeply-dipping footwall slopes requires that consideration be given to footwall stability."

Jan 1, 1988