Search Documents

By T. M. Williams, P. M. Green

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The sediment geochemistry of streams draining Southern Uplands and Lake District turbidites was compared with lithogeochemical data for the source greywackes, using stratigraphically defined catchments. Several systematic trends in element abundance variation between source and stream sediment can probably be applied more widely to interpretation of drainage geochemistry. Pb and Zr increase markedly from source rock to sediment, by adsorption on clay and zircon grain concentration. Variation of feldspar-related elements Rb, Sr, K and Ba appears to be controlled by source grain size and compositional maturity. Ni shows surprisingly little change and Fe and Co are only slightly raised. Cr is particularly useful, with variations superimposed in anomalously high regional levels. Abrupt changes in Cr distribution in stream sediment coincide with stratigraphical boundaries, allowing drainage data to be used as a surrogate for whole-rock values

Jun 19, 1905

By Khamis Y. Haramy

Quality assurance and quality control of drilled shafts has become a concern due to difficulties in accurately locating construction anomalies and determining load bearing capacity of defected drilled shafts. Various non-destructive evaluation techniques have been developed to estimate the integrity of the concrete in drilled shafts. While these techniques have been widely accepted, variables and unknowns can affect the measurement results. Results are typically difficult to interpret, leading to unnecessary construction delays and possible litigation over shaft integrity. In addition, influences of surrounding ground materials, stress states under different load conditions, and crack and residual stress development during concrete curing further complicate determination of shaft performance. This paper focuses on the evaluation of load bearing capacity of defected drilled shafts under various conditions by numerical analysis and modeling.

Jan 1, 2007

By J Lyall Workman, Peter N. Calder

"Large hole rotary drilling is one of the most common methods of producing blastholes in open pitmining. Large hole drilling generally refers to diameters from 9 to 17 inch (229 to 432 mm), however aconsiderable amount of rotary drilling is done in diameters from. 6% to 9 inch (165 to 229 mm). Thesesmaller diameters are especially prevalent in gold mining and quarrying."

Jan 1, 1996

By O. Gunaydin

Performance measurements of large-diameter circular saws were conducted on eight different carbonate rocks in marble factories located in some areas of Turkey. Rock samples were collected from these factories for laboratory tests. Uniaxial compressive strength, tensile strength and impact strength were determined in the laboratory. The brittleness of B3 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), the brittleness of B5 (the product of percentage fines in the impact strength test and compressive strength) and the brittleness of B8 (half of the product of compressive strength and tensile strength) were calculated from the test results. Hourly slab productions were correlated with brittleness indexes. It was concluded that sawability of carbonate rocks can best be predicted from the brittleness of B8.

Jan 1, 2004

By S. Hoskins, S. Chiovelli

"The annual budget for the repair and maintenance of equipment at Syncrude Canada Ltd. is in excess of $450 million. Of this amount, a significant portion can be attributed to the loss of material on various pieces of equipment throughout the operation. In order to effectively battle the different wear and corrosion mechanisms that lead to material loss, it is important to understand how materials behave in the environments in which they are used. Through the work carried out at Syncrude, and work conducted with various external collaborators, significant improvements in both equipment reliability and productivity have been achieved. This paper will review some recent field trials where materials research has demonstrated the potential for significant improvements in equipment run life and reduced maintenance costs. These field trials will demonstrate the need for understanding the interaction between various damage mechanisms and the materials used in different services. The paper will also discuss current areas of focus along with future directions for further work. IntroductionSyncrude Canada Ltd, located in northern Alberta, Canada, operates a mining, extraction, and upgrading facility that removes bitumen from oil sand to produce synthetic crude oil. Oil sand is mined from the orebody using conventional open pit mining techniques. Recently, the mining scheme has changed from a dragline/bucketwheel/conveyor system to a shovel/truck/crusher/hydrotransport operation as depicted in Figure 1. Since the start of production in 1978, the identification, development and application of wear protection has been an ongoing challenge due to the abrasive nature of the oil sands and the massive volumes of materials that are moved. The use of various materials and application processes along with component design modifications has resulted in significant improvements in both productivity and reliability (Adamic et al., 1995; Llewellyn, 1996, 1997; Anderson et al., 1998; Chiovelli et al., 1998).In an effort to continuously improve the operation, Syncrude has been quick to adopt new wear technologies. As seen in Figure 2, since the start of operation, a variety of materials have been used to increase wear performance and ultimately equipment reliability and availability. Although Figure 2 does not show a time axis, the bottom axis may also be used to represent a time progression for the predominate use of these materials at Syncrude. Tungsten carbide metal matrix composite (WC-MMC) overlays are currently the materials of choice for most of Syncrude’s critical production applications. Metal matrix composite overlay technology has potential for significant improvements and Syncrude is actively working with powder consumable manufacturers to advance this technology."

Jan 1, 2004

By W. C. Peters, M. W. Pullen, C. A. Bays

During the past three and a half years considerable improvement in the techniques of solution extraction of salt has been made by the use of wells which are cross-connected by hydraulic fracture at the base of the salt. Fracture is initiated by the application of hydraulic pressure. Underreaming and perforating techniques are used to control initiation. The fracture is then extended by continuous pumping until a pressure communication is obtained. Pressure communication is followed by washing-through to obtain a low-pressure connection. Well construction using non-shrinking cements that will bond with the salt and with associated strata is essential to the process. The connecting procedure described permits solution to attack the salt deposit from its base upward, thereby permitting greater recovery, fewer well repairs, better saturation of brine, and overall economy of development and operation. The fracture method of cross-connection requires special pumping of the fluid and is limited by present experience to initial well spacings up to about 1200 feet. The method has been used in bedded salts and is applicable for wells in salt domes. Since spring of 1956, new developnents in salt extraction wells have followed procedures substantially different from those in prior use. Although multiple well systems, connected either by the natural consequence of the solution process or by undercutting under protective pads, have been used previously, the past three and a half years have brought about new designs and new operation procedures based on cross-connection of the wells using hydraulic fracture. To date these techniques have been applied largely in the bedded salt deposits of Michigan, Ontario, Ohio, West Virginia, and New York. To the writers' knowledge they have not been used in salt dome wells. The methods have not yet been in use for a sufficient period to permit any statistical comparison with the older methods. It is evident from experience to date that the methods result in higher recoveries, lower capital and operating costs, better saturation of produced brine, reduced well maintenance and repair, and in considerably fewer production units to insure

Jan 1, 1961

By Richard Manrique

"La implementación del proyecto de modernización de la fundición de cobre de Southern Peru Copper Corporation requiere cambiar la metodología de funcionamiento de los sopladores para la etapa de conversión. En este sentido, el presente texto señala los aspectos del Sistema de control maestro de reparto de carga implementado en la Fundición de Ilo con excelentes resultados, logrando mejorar el rendimiento de los equipos con una antigüedad de mas de 30 años e invirtiendo tan solo en nuevos controladores en una etapa ligada directamente a la línea de producción. Mantener la variable primaria presión en la red de sopladores, compartiendoóptimamente la carga entre los sopladores en la red, mientras que, se minimiza el riesgo de surge, consumo de energía y los disturbios en el arranque y el paro de sopladores individuales, el sistema deberá ser lo suficientemente flexible que no deberá de perturbarse ante la salida frecuente de los convertidores, es decir deberá de mantener las presiones y flujos a la descarga del manifold ante las variaciones en el consumo de aire todo esto con un mínimo de venteos al ambiente."

Sep 19, 2006

By C. M. Badeen, J. Paige, W. Evans, L. McCauley, A. Caddies, I. Alilovic, R. Turcotte, C. O. Lyogun, C. Bonner

Gear pumps are very commonly used for the pumping of AN-water based emulsion products for both handling and blast loading applications. The potential major hazardous problems likely to be encountered with these pumps are: (i) high probability of friction; (ii) possibility of product confinement in the area of the bushings; (iii); high bearing failure rate; (iv) pump running dry; (v) presence of foreign material; (vi) deadheading of pump; (vii) delamination of elastomer from steel gears. Of all these possible scenarios, the no-flow situations where the pump is running dry or deadheaded have always been recognized as the most serious ones.

Jan 1, 2015

By Tripathy A. K, Satapathy B. K, Nayak B, Mohanty J. N, Dey D. N

The paper deals with the metallographic tudy of heat treated chromite and chromite-coke composite briquettes. The briquettes, prepared from chromite concentrate of Orissa Mines using molasses-lime, dextrinelime and tamarind seed as binders, were subjected to different temperatures and examined metallographically. The change of phase with temperature was analysed by X-ray diffraction.

Jan 1, 1987

Characterizing coal mine roof rock is extremely important for hazard assessment, reinforcement, and entry design. The Coal Mine Roof Rating (CMRR) is an innovative rock mass classification that has found acceptance in the coal mining industry. A disadvantage of the original CMRR is that it cannot be determined in advance of mining, because it requires underground observations. An entirely new set of procedures have now been developed to determine the CMRR from exploratory drill core, as described in this paper. The new procedures employ Point Load Tests (PLT) to determine strength parameters that account for approximately 60% of the rating. Both diametral (parallel to bedding) and axial (perpendicular to bedding) PLT are conducted. The diametral tests allow estimates of bedding plane cohesion and rock anisotropy, both of which are critical to estimating susceptibility to horizontal stress. Traditional core logging procedures are used to determine discontinuity spacing and roughness. To ensure compatibility with the original CMRR, the new rating scales were verified by comparing drill core results with nearby underground exposures. To assist mine planners in using the new CMRR procedures, a large database of strength ratings of roof rocks was assembled through extensive point load testing and logging. Over 2000 point load tests (both axial and diametral) have been made on 30 common coal measure rock types from mines representing most U.S. coalfields. This database has been merged with the popular core rating system of J.C. Ferm into a field guide for geologists and engineers. By using the pictorial classification system of Ferm to identify the rock, typical CMRR can be compared with values calculated using the new CMRR procedures.

Jan 1, 1996

By Krogerus. H., P. Jokinen, T. Lintumaa

Keywords: Pyrometallurgy, furnace, coke, smelting charge, optimization, ferrochrome The main consumer of ferrochrome is stainless steel production. Stainless steel must maintain a reasonable price against other competitive materials. Therefore, the ferrochrome price must be low enough and profitable for the producers of stainless steel. The investment and operational costs of ferrochrome production are greatly dependent on the availability of the process and the production rate. Thus the furnace size and production rate in submerged electric arc furnaces will be greatly increased in the near future. The ferrochrome production per furnace, e.g. at Outokumpu?s Tornio Works, increased from 30 000 t/a to 165 000 t/a in about 35 years. The same trend will continue globally but now much more quickly. The Outokumpu ferrochrome process at Tornio Works uses sintered chromite pellets and upgraded lumpy ore as a chromite source. Metallurgical coke is used as a reductant. Reliable smelting in a large furnace demands the correct charge composition and well-known characteristics of the charge components. The quality and electrical conductivity of cokes (normally used) has the most important role for the electrical conductivity of the smelting charge. The results of the measured electrical conductivity of different cokes and the smelting charge with many controlling factors are presented here. These measurements were performed over the years for our own purposes at the laboratory of Outokumpu Research Oy (ORC), in Pori, Finland.

Jan 1, 2006

By Roberto Bria

El presente texto describe el módulo prefabricado para las salidas de emergencia. En este sentido, el sistema modular prefabricado busca facilitar y agilizar la instalación de salidas de emergencia desde el interior de mina hasta superficie mediante RB entubados con módulos armados fuera de la Unidad Minera, mejorando la seguridad mediante un sistema confiable de fácil colocación, reutilizable, y de gran robustez. De ese modo cumplir con el objetivo primordial de las salidas de emergencia de 200 m hasta la superficie, en terrenos de calidad de roca regular a mala.

Sep 21, 2013

By Douglas Rudenko

Have you ever had a neighbor complain about a blast one day, but says the next day’s blast was better, even though the Peak Particle Velocity (PPV) increased? How about neighbors that complain about a small trimming shot, but don’t complain about a big production shot? Have you ever reduced the pounds/delay and gotten more complaints ? Mine operators are often bewildered when trying to correlate blast design parameters to homeowner complaints. When complaints come, standard practice is to set up a seismograph in the neighbor’s yard to monitor the blast. Immediately after the blast, the neighbor usually reappears from the house wanting to know the seismograph reading. When told that the PPV was 0.1 in/set, well below damage levels, the homeowner explodes saying “Your machine is wrong”. Perhaps he is right. Understanding why people complain about blasting is not about PPV, it’s all about structural response. People could care less about how much the ground vibrates; they only care about how much their house vibrates. In this paper we will examine the primary factors that control structural response. Through the use of a large array of digital seismographs, the effects of two production blasts on a community surrounding a quarry are studied. The predicted structural response resulting from each blast is calculated at 175 seismograph locations. The predicted response is then correlated to previous research on human perceptibility to vibrations. The results of this analysis and correlation give a better understanding of what the residents actually feel in their homes. The detonations of two single-hole signature blasts are also recorded by the array of seismographs revealing the dynamic characteristics of the geology ‘surrounding the quarry. Once the influence of the geology was understood, blasts were configured to disrupt the natural rhythm of the site through the use of millisecond delays.

Jan 1, 2000

At the Orieco mine quartz veins carrying sulphides were localized in parts of an extensive fault zone in the Mathinna Beds during late Middle Palaeozoic mineralization.These deposits were subsequently exposed, and oxidation of the sulphides by percolating groundwaters resulted in the formation of gossans at the surface, and replacement close to the permanent water table of the more soluble sulphides by copper sulphides (chalcocite, coveIlite). A restricted zone containing copper oxides (cuprite, tenorite), copper carbonates (malachite, azurite), iron arsenates (scorodite, pharmacosiderite) and possibly rare copper sulphates occurred above the water table.The renewed oxidation of these deposits following mine development has been facilitated by the ready circulation of air and water combined with the formation of large free surfaces ideal for evaporation of aqueous solutions. Under these new conditions of high initial sulphate concentration, low pH, and relatively high Eh, the previously formed mineral assemblage is unstable and numerous Cu (Fe,Zn)-sulphates and Fe (Cu,Pb)-arsenates are presently forming in fractures in the fault zone and on the adit and stope surfaces for some considerable distance from the Sulphide-rich ore shoots. The observed spatial sequence of the major sulphates with respect to the sulphide-rich zones (Le. chalcanthite-antleritebrochantite and langite) is consistent with decreasing sulphate concentration and increasing pH away from the oxidizing sulphides.

Jan 1, 1970

By David Chapman, Glen Frank

Due to the transport mechanics of the depositional environment, glacial soils display a very wide range of grain sizes and behavior. Several nonstandard drilling, sampling, and analytical techniques are therefore required to characterize the subsurface. The paper summarizes the geotechnical investigation for the design of a large project in glacial geology, which will include both large and small diameter pressure balance tunneling. The paper focuses on the challenges presented by the glacial environment and the techniques required to identify and characterize it for design and contract document preparation.

Jan 1, 2001

By C. McCall, J. T. Knight, J. R. Ridley

Gold mineralisation in the gabbro sills is mainly stratabound to quartz- and Fe-rich, granophyric-textured units and is sited in undeformed, brittle quartz vein sets, which form pipe-like orebodies. Hydrothermal wallrock alteration consists of hornblende-plagioclase-calcite-quartz with minor biotite, garnet and chlorite and with arsenopyrite and pyrrhotite as the dominant sulphides. Geothermobarometric data suggest that gold was deposited at around 520 degrees C at 2.8-3.8 bar. Mineralisation is thought to have occurred during amphibolite-facies metamorphism. Fluid inclusion and isotope data indicate that gold mineralisation was the result of deposition from a low-salinity H2O-CO2-CH4 fluid of either metamorphic or magmatic origin. Although the Three Mile Hill deposit differs from others in the area in its wallrock-alteration assemblages, peak-metamorphic timing of gold deposition and distinct geochemical associations it forms a brittle stratabound ore body which suggests structural and gold-depositional mechanisms in common with those of the other gabbro-hosted gold deposits

Jun 18, 1905

Some form of technical library is a necessity for every metallurgical plant, but its form and scope will vary with the conditions of each case. In its simplest form, it may consist of one or two mining journals and a few text books distributed amongst the staff. Again, it may be a separate establishment controlled by a clerk, the technical staff necessarily making its own research into the literature available. A still more elaborate organisation may be established both to supply information when requested and to keep the operating staff in touch with current matters of interest, and the library service of the Electrolytic Zinc Co. of Australasia is of this character.The necessity for such a service is due to several facts. The Company's interests are scattered over three States. Most of its staff members are remote from: good public library facilities and they have few opportunities for exchanging ideas verbally with other metallurgists and engineers. Then, too, the process of recovering zinc by electrolysis, is a young art of which the physical and chemical bases were far from fully known at the time the: Risdon plant was established. Most of the zinc produced is sold abroad, and this unsheltered industry can afford to miss no technical or economic development which may promote its efficiency. Add to these facts the geographical isolation of the Commonwealth and the case for an adequate library is complete.

Jan 1, 1934

By Mark S. Sanders

This report presents recommended visibility requirements for continuous miner, shuttle car and scoop operations and details the methodology used to generate them. A task analytic approach was used to define information requirements and visual features which served as sources of information. Information requirements were prioritized and the location of visual features determined. From this analysis, visual attention locations, containing one or more important visual features, were identified. A total of 71 locations-were identified for continuous miners, 54 for shuttle-cars and 54 for scoops. A procedure was developed for assessing whether operators in existing machines could be expected to see the visual attention locations. The procedure makes use of a Human Eye Reference Measurement Instrument (HERMI) designed for this project and an outside-in photographic procedure for documenting compliance with the recommendations. A sample of continuous miners, shuttle cars, and scoops were used to test the procedure. Results are presented in the report.

Jan 1, 1981

Measurement of densities, susceptibilities, permanent magnetization, and calculation of demagnetization factors has allowed computer modelling of gravity and magnetic data over the Middleback Range iron formations of South Australia. As well as providing structural information, the study emphasizes the effects of weathering on the interpretation of magnetic data.

Jan 1, 1975

By Za-Chieh Moh

This paper presents a summary of the current pile foundation practice in Taiwan. Constructions of driven piles, drilled shafts, and barrette foundations are reviewed. This paper also briefly summarizes the pile works of four major construction projects in Taiwan, namely, Hsin-Ta Power Plant, Taichung Power Plant, Taipei Transit Systems, and Taiwan High Speed Rail.

Jan 1, 1996