Search Documents

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

By F. Dehghani, B. Rezaie, T. Ghosh, A. Sachan

Comminution is an integral part of the mineral extraction process. However, the influence of the comminution method (ball and rod mills) on silica and magnetite particle shapes has not been substantially investigated. Shape parameters for fractions of -250+212, -150+125, and -106+75 μm sizes were examined utilizing a scanning electron microscope and a Clemex vision PE image analysis system. The silica particles displayed higher elongation and flatness parameter values for rod mill products, but roundness and relative width parameter values of rod mill products are less than that of the ball mill products. Magnetite particle elongation and flatness parameter values of ball mill products in fraction sizes of -250+212 and -106+75 μm are larger than rod mill products, but roundness and relative width parameter values of ball mill products are smaller than rod-mill products, but for the -150+125 μm size range the result is converse. Furthermore, particle elongation and flatness increased with decreasing particle sizes of silica, whereas, roundness and relative width decreased for both Ball and Rod Mills. In case of magnetite, ball mill products displayed an increase of flatness and particle elongations with decreasing particle sizes but flatness increased and roundness and relative width decreased. Similarly for rod mills, magnetite fractions of -150+125 μm were found to have the largest values of elongation and flatness. INTRODUCTION Comminution alters the size and shape, causes lattice distortion, changes chemical composition, surface area, surface-free energy, and polymorphic transformation of all materials. The quantity and quality of such changes depend on specifications of the material feedstock, the type of mill being utilized, the specific energy input, ambient temperature, and environmental pressure [1]. The shape difference between the milled products depends on different grinding mechanisms and the respective breakage principles that these mechanisms depend on [2, 3]. With decreasing particle sizes, the nature of the particle surface become crucial [1]. The influence of the breakage technique has been found to be non-trivial and heavily dependent on the type of grinding mill used for particle size reduction [4]. Shape is an important industrial parameter for predicting particle behavior in downstream processes. The shape parameter affects the way particles burn, compact, are recovered, flow in fluids, sinter, float, agglomerate, fluidize, interact with pulmonary tissue, cut, abrade, react with chemicals, form structural materials, and retain and permit fluids to flow [5, 6]. The distribution of particle sizes and shapes are important for mining, civil and chemical, pharmaceutical, and various other industries with interest in the population modeling of atmospheric dusts, smoke, and grit [1, 3, 6]. The shape parameter not only affects the chemical, physical, surface properties of particles but is also important for downstream processes [5, 6]. Image analysis has been found to provide detailed information about size and shape of the particles and can be used for the control of product quality [4].

Jan 1, 2019

Real time analysis of ore quality between the mine and mill provides major benefits to copper mining and processing operations. Prompt gamma neutron activation analysis (PGNAA) is a proven technique that has been successfully applied for real time conveyed flow multi-elemental measurement. The advantage of PGNAA is that it measures through the full conveyed cross section continuously and provides representative element measurement without the need to constantly sample coarse (primary crushed) conveyed flows. High specification PGNAA analyzers enable accurate measurement over time increments as short as thirty seconds. Elements such as copper can be measured to a precision of 0.02% copper which is sufficient for high confidence in decisions for bulk flow diversion. Increments of eight tonnes are being diverted through a bulk ore sorting application to remove batches of waste from mill feed as well as divert material to different stockpiles based on ore quality. Longer measurement increments of two to five minutes are suitable for blending control of ores to reduce feed quality variability and to control average ore quality within a target range. Feed blends can be adjusted as frequently as required but typically multiple measurement increments are composited to produce a rolling average ore quality. The paper details two case studies where analyzers have been successfully used to measure conveyed flows for blending and bulk diversion applications. The real time measurements of ore composition are also used for ore reconciliation, in metal accounting and providing process operators with advance warning of ore quality changes that may affect grinding performance and cause process upsets. Real time ore quality measurement has proven beneficial in improving copper processing performance through better utilising plant capacity in a leaching operation, optimising ore feed quality, and reducing unnecessary processing of waste. INTRODUCTION Representative real time elemental analysis of conveyed ore quality using fully penetrative technologies has been available to the minerals industry since the 1990s. The Prompt Gamma Neutron Activation Analysis (PGNAA) technique was developed into a conveyed material analyser and soon adopted by the cement and coal industries which recognised the benefits in real time quality management. These commodities were ideally suited to this measurement technique as operations generally involved conveying bulk material prior to processing. Measured quality was used to divert material to different destinations or used to control blending for improved quality consistency. Uptake in the minerals industry, however, has been slow until the last ten years, and particularly until the mid-2010s.

Jan 1, 2019

By F. F. Roberto

Sulfuric acid has been demonstrated to be an efficient lixiviant for in situ extraction of copper in the past. It has also been proposed that microbial production (by iron-oxidizing acidophilic bacteria) of acidic ferric solution either in situ or ex situ could provide an economic strategy to generate an effective lixiviant for secondary copper sulfides like chalcocite and covellite. Copper heap bioleaching also takes advantage of this approach. One of the major environmental challenges for in situ copper recovery projects is the containment of acidic solution within the ore deposit, and ultimate restoration of the depleted ore body to its original state. A perhaps overlooked aspect of projected site operations is the possibility that transient acidic conditions and pumping of solutions from surface reservoirs into the subsurface could stimulate the growth of iron- or sulfur-oxidizing species of acidophilic microbes in the ore body, leading to additional generation of sulfate, acid, and ferric iron. This outcome would benefit extraction of copper in mixed oxide/sulfide deposits in the near term, but could complicate restoration activities. Possible impacts of pumping acidic solutions into the subsurface on microbes resident in, or introduced into the extraction zone will be discussed in the context of our understanding of copper heap bioleaching and acid rock drainage. INTRODUCTION As high-grade deposits of metals such as copper continue to decline, conventional mining methods have evolved to mine and process larger and larger quantities of ore. What is currently defined as ore today often contains less metal than the tailings of past operations. The throughput of current-day mines also leads to tremendous amounts of waste rock and tailings that may threaten the environment and communities around the mines, as has recently been experienced by 3 major tailings disposal facility (TSF) dam failures in the past 5 years. Community acceptance of large mine operations thus becomes more difficult to achieve—loss of the social license to operate. In response, the mining industry urgently pursues innovations that can fundamentally change the way in which metals are mined. In situ recovery (ISR) of metals represents one approach to a more sustainable mining industry, by virtually eliminating the need for a pit or underground excavation, eliminating the excavation and transportation of ore to a process plant and the ensuing noise and dust that is generated, and any need for waste rock dumps or TSFs. An ISR mine could have very little visible footprint beyond a network of wells, pumps, and piping to transport pregnant solution to a recovery facility, such as a solvent extraction- electrowinning (SX-EW) plant for copper. Some solid waste streams and/or storage ponds may still be necessary to treat and store bleed streams, PLS and raffinate, or as part of groundwater restoration activities. Thus capital and operating investments would be potentially much lower than that required for a conventional mine. In theory production could also be controlled to adjust to subsurface ore grade and match market demand. A not insignificant challenge of in situ recovery is the requirement for an efficient, low-toxicity, and ideally selective lixiviant for the metal that is targeted.

Jan 1, 2019

By Arnfinn Prugger

"The construction of the new Scissors Creek shaft at the Rocanville mine, the first potash shaft successfully completed in Saskatchewan Canada since 1979, is summarized here. Located 15km from the existing Rocanville surface plant, this new 6 m inside-diameter, 1121 m deep service shaft was built for fresh-air ventilation and access. Shaft construction in the Saskatchewan sedimentary basin involves sinking through five different rock-types: glacial tills, shales, sandstones, carbonates and salts. The first four rock- types are all water-bearing, and the salts will dissolve in water. This results in five different sinking challenges and requires five different shaft lining designs. The upper 580 m of rock (the till – shale – sands sequence) was frozen before sinking, and grouting methods were used for water control through deeper carbonate levels. Challenges that were faced and overcome during shaft sinking are reviewed, and ideas that future operators working in sedimentary basin environments might consider in order to avoid these difficulties are discussed.INTRODUCTIONThe Nutrien Inc. (formerly Potash Corporation of Saskatchewan Inc. / PotashCorp) Rocanville potash mine in southeast Saskatchewan, Canada has been in continuous production since 1971. Devonian potash, formed approximately 380 Mybp, is mined in a sedimentary basin environment at approximately 1000 m depth below surface in this area of Saskatchewan. The predominant use for finished potash products is fertilizer: potash fertilizer is concentrated and nearly pure KCl (i.e. greater than 95% pure KCl). Currently 10 potash mines are in operation in Canada, all in Saskatchewan. In 2018 Saskatchewan mines produced ˜ 23 million tonnes of finished potash products, which is approximately 35% of World demand of ˜ 66 million tonnes for the year (e.g. Nutrien Inc., 2019).In November, 2007 it was announced that the Rocanville potash mine would be expanded to increase production from 3.0 Million tonnes per year (Mtpy) to approximately 6.0 Mtpy of finished potash products, requiring an increase in hoisting capability from approximately 9.0 Mtpy to over 18.0 Mtpy. The Rocanville potash mine has historically been accessed through two shafts: a production and ventilation exhaust shaft, and a service and ventilation fresh-air shaft located approximately 200 m from each other. All surface offices, processing facilities, etc. are situated near these original shafts.A very important part of the recent Rocanville expansion involved the construction of a new service shaft (6 m diameter, 1121 m deep) for fresh-air ventilation and access, approximately 15km west of the existing surface plant. Once this third shaft was completed in 2015, the historical service shaft was converted to a second exhaust and production shaft. Three shafts are now available for mine access, ventilation and ore hoisting at Rocanville. As of December 31, 2017, annual nameplate capacity for Rocanville was 6.5 million"

Jan 1, 2019

By B. D. H. Knights, N. B. du Preez

The recovery of the economy of the Democratic Republic of Congo has allowed for the rapid increase in production of copper from this region, while the increased price of cobalt continues to support the recovery of that country’s economy. This has enabled the modernization of the process technology used, particularly the change from direct electrowinning of copper to solvent extraction-electrowinning. With this change has come a variety of technical challenges in optimizing the recovery of cobalt from these sources. In this paper, we discuss aspects of the flowsheets for the production of cobalt from the ores of the DRC and Zambia, highlighting the technological improvements that have been made. Following this description of the practice, we assess the challenges of further improving the recovery and purity of cobalt from these sources. INTRODUCTION The African Copperbelt (Figure 1) is by far the biggest producer and holds the greatest reserves of cobalt (Sheed, 2015). However, the ores of this great mining region are extracted primarily for their copper content, and cobalt is a by-product. The ratio of copper-to-cobalt is between 6 and 20 to 1, with the ores from the DRC richer in cobalt than those from Zambia. The overall supply of cobalt, shown in Figure 2, is increasing due to an increase in demand for its use as a battery material. Cobalt is used in superalloys, hard metals, pigments, catalysts magnets, tyre adhesives, lithium-ion rechargeable batteries, and wear-resistant coatings, amongst others. Although these generic categories persist, Figure 3 shows how the relative usage of cobalt is changing due to the uptake of electric vehicles in China and Europe. Cobalt is a key element in lithium-ion batteries, and because it is widely anticipated that electric vehicles will be legislatively encouraged, it is anticipated that the demand for cobalt will rise. This anticipated increase in demand resulted in an increase in the price for cobalt, to which suppliers responded over-eagerly, and the price has dropped dramatically in the first few months of 2019, as shown in Figure 4. However, there is a clear cycle of price peaks in cobalt’s history.

Jan 1, 2019

By Euler De Souza, J. Daniel Stinnette, Julian Varaschin

"This paper outlines some of the factors that affect the airflow required for the ventilation of modern diesel-powered equipment and of electric equipment and examines how they can be applied in determining reasonable ventilation rates for Tier IV compliant diesel equipment and for electric equipment operating in mining environments. Airflow calculations for modern diesel-powered equipment and for electric equipment are more complex and must be based on a combination of factors that are unique to each mine. Methodologies for ventilation rate determinations for each case are proposed in this paper.INTRODUCTIONTraditionally, airflow requirements for production and support equipment operating in underground mines have been determined by multiplying the vehicle power by a ventilation rate that was either mandated by regulations or determined empirically from known quantities. However, in light of the drastic reductions to diesel equipment emissions mandated by the US EPA Tier IV and EURO Stage 4 regulations, there is still a great deal of uncertainty in the underground mining industry among those responsible for the ventilation of planned new mines or the expansion of current mines. The question remains, what ventilation rates should the ventilation system designer apply for modern diesel equipment?Also, given the ongoing development of grid/battery-electric equipment and active construction of fully electric mines, it has become critical to determine adequate airflow rates per brake kilowatt of electric engine power. One of the most important criteria for determining ventilation rates for electric equipment is the amount of heat they generate, as this is the most significant emission produced by electric equipment (which do not produce exhaust gases or particulates). Therefore, ventilation rates required to dissipate heat from electric equipment must be suitably determined for all electric vehicle fleets operating in underground mines."

Jan 1, 2019

By M. R. Shahan, W. R. Reed, P. Zhang, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3,000 cfm (1.42 m3/s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts; and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s). INTRODUCTION Roof bolting machines are used to drill bolt holes into the roof of an underground mine at specified patterns and to install roof bolts to secure the roof from falling. At times, the roof bolting machine is also used to install rib bolts; however, only the roof bolting operation was considered in this simulation. Though the roof bolting operation drastically improved the safety of miners from roof falls, some roof bolter operators are experiencing health problems associated with respirable dust. Based on recent statistics [1], following a low point in the late 1990s where the prevalence of coal workers’ pneumoconiosis (CWP) in miners with 25 years or more tenure was approximately 5%, CWP now exceeds 10% for miners with 25 years or more of tenure. In central Appalachia (Kentucky, Virginia, West Virginia), 20.6% of long-tenured miners have CWP and 4.5% have progressive massive fibrosis, the most severe form of CWP. CWP, also known as black lung, is an occupational respiratory disease that has no cure and can ultimately be fatal. The only way to prevent the incidence of black lung is to eliminate miners’ exposure to respirable coal mine dust. Current U.S. regulations require that the overall respirable dust concentration to be 1.5 mg/m3 or less for a full-shift sampling if respirable quartz is not present; otherwise, the standard is 10 divided by the percent quartz (not to exceed the 1.5 mg/m3 respirable dust standard) [2, 3].

Jan 1, 2019

By F. A. Auld

"Traditionally deep shaft sinking from the ground surface was carried out using drill and blast methods. Although large diameter blind shaft drilling has been carried out successfully on numerous occasions previously, including as early as 1852 in Germany (Auld, 1995), little attempt has been made until more recently to mechanise the shaft sinking excavation process using down-the-hole machines. This paper reviews the development of deep shaft sinking machines from the early 1970’s up to the present day. INTRODUCTION Mechanical excavation methods can significantly improve excavation performance, in order to access natural resources faster, and labour safety is increased compared to drill and blast operations. However, shaft sinking machines need to be capable of accommodating all the basic requirements for deep shaft sinking, namely: 1. Excavation and muck removal 2. Ground stability control 3. Groundwater ingress control 4. Temporary lining installation 5. Permanent lining installation and watertight sealing 6. Ventilation 7. Secondary means of egress for personnel In addition, how the machine operates in the shaft is an important factor, either slung on ropes from a surface headgear or on its own in the bottom of the shaft. An all-embracing machine which can deal with all of the above conditions is impossible but many of these requirements can be incorporated into a single machine. Deep shaft sinking also differs greatly from normal tunnel construction which employs the use of either a roadheader arm installed within a shield or a full-face tunnelling machine for excavation. Hydrostatic pressure and ground stability problems increase with depth, whereas in tunnelling the depth is normally relatively shallow and the aforementioned factors remain approximately constant along the tunnel length. DEEP SHAFT SINKING MACHINES All the shaft sinking carried out previously in the UK was by the traditional method of drill and blast. Elsewhere, in other parts of the world, attempts have been made to mechanise the process."

Jan 1, 2019

By T. Hidayat, D. Shishin, V. Prostakova, M. Shevchenko

The chemical compositions of copper feed streams are becoming increasingly complex following the growing demand for metals and corresponding shortages of primary sources. The optimisation of process conditions requires an accurate description of phase equilibria and thermodynamics. Integrated experimental and thermodynamic modelling research program on the characterisation of the complex, multi-component, multi-phase gas-slag-matte-speiss-metal-solids Cu2O-PbO-ZnO-Al2O3- CaO-MgO-FeO-Fe2O3-SiO2-S-(As-Bi-Ni-Sb-Sn-Ag-Au) system is being carried out to support companies undertaking the pyrometallurgical primary production and recycling of copper. The experiments involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of equilibrium phase compositions with quantitative microanalytical techniques, including electron probe X- ray microanalysis and Laser Ablation ICP-MS. The thermodynamic modelling is undertaken using FactSage computer package with advanced thermodynamic solution models. The continuing development of research methodologies has resulted in significant advances in research outcomes. Implementation of the results of these fundamental studies involves an ongoing collaboration of researchers and industry technologists. An overview of recent progress in research, implementation and applications in industrial practice are given in the paper. INTRODUCTION Rapidly developing technologies increase the demand for various metals in number and volumes. Modern technological devices such as mobile phones, computers, other electronic devices, have dozens of metals—all those metals have to be a) produced and b) recycled. The fast transition in mobility from fossil energy delivered through combustion to renewable energy first stored in bakeries and delivered through electric engines introduce a significant change in the metal demand in terms of both type and volume of metals. Pyrometallurgy is playing a key role in supporting these changes in our industrialised society.

Jan 1, 2019

By W. Dziurzynski, St. Wasilewski, T. Palka, A. Krach

"Air parameter monitoring systems, regardless of gasometrical protections, provide a significant number of measurement data. The obtained data broadens the knowledge on processes taking place in underground workings and shows the relationships and influence of machines and technological processes on the variability of ventilation parameters in the areas of longwalls. Nowadays, computer simulation methods are increasingly used to reproduce the flow of air and methane mixture in the area of longwalls equipped with shearers. The paper presents the results of a research experiment covering a long-term observation of a longwall area during mining with a shearer using sensors from the mine's monitoring system. Data from sensors for methane concentration, pressure and velocity were used and additional ventilation measurements were taken to determine the parameters characterising the air flow in the area. The influence of different machine cycles in the longwall on the changes of air parameters in the area of the longwall was shown. A numerical model of the ventilation area was developed and the computer program VentZroby was used for the calculations, which allows for the simulation of the process of ventilating the area of the active longwall during the extraction of coal with the use of a shearer and haulage of the run-of-mine. Computer simulation of the influence of the shearer's operation and the methane inflow associated with the distribution of the mixture of air and methane was carried out. The results of the simulation were compared with the data recorded by the monitoring system’s sensors during the measurement experiment. Comparison of the recorded methane concentration courses with the results of a computer simulation of the air and methane flow conditions in the mining area showed changes in the gassiness. INTRODUCTION Studies carried out in the Polish and global mining industry show that methane is an obvious factor in limiting mining production due to the loss of continuity in the operation of longwall complexes in hard coal mines under methane emission hazard (Schatzel et al., 2008). In addition, methane hazards have a significant impact on the safety of the operators of machinery in the longwall. The requirements of Polish regulations and the practice of safe operation of mining longwalls require correct determination of gas concentration, volume flow, as well as pressure and temperature of the flowing air. As part of the research undertaken in the Budryk (Wasilewski, 2010) and Bielszowice (Dziurzynski et al., 2009) mines to assess the methane hazard in the longwalls and workings in the vicinity of the longwall, research experiments were carried out, during which air parameters were recorded by the mine monitoring system and additional testing equipment in different cycles of shearer operation."

Jan 1, 2019

By Bradford C. Wesstrom, Ricardo Parra

The Freeport McMoRan El Paso Refinery uses co-generation to produce some of its electricity and all of its steam. This paper will cover the operation of the co-generation plant natural gas turbine at a fixed RPM for blade longevity and energy output. The by-product heat from the turbine passes through boilers with additional heat from a duct burner to produce steam for the Tank House and auxiliary operations. The steam demand varies dramatically throughout the day based on unloading activities in the Tank House. The use of an automated steam control system within the El Paso Refinery will help stabilize line pressure by incrementally controlling steam consumption based on electrolyte temperature. This will minimize steam line pressure fluctuations. INTRODUCTION In the mid 1920’s the Nichols Copper Company of Laurel Hill, New York recognized the need for a modern copper refining facility in the southwest. Due to the many railroad heads, affordable power and abundant labor supply, and the close proximity to regional copper smelters in Mexico, Arizona, and New Mexico, El Paso became the logical location. In December 1928, ground was broken for the joint venture refinery between the Nichols Copper Company, Phelps Dodge, and the Calumet and Arizona Mining Company. In September 1930, Nichols Copper Company became a part of Phelps Dodge Corporation after a stock exchange. In July 1938, Nichols Division officially became Phelps Dodge Refining Corporation. In March 2007, Freeport McMoRan Copper & Gold acquired Phelps Dodge. Energy costs (electrical and thermal) are critically important in the viability of modern copper electrorefineries. The El Paso Refinery produces electricity and steam through its cogeneration system. The El Paso cogeneration facility is a natural gas, 15-megawatt facility containing five turbine generators and associated waste heat recovery boilers. The facility is divided into two phases. Phase I consists of two Allison 2.2-megawatt turbine generators. Phase II consists of three Solar Taurus 3.5-megawatt turbine generators. Presently three units in Phase II are operated. The Phase I units were purchased and installed in 1986 and the Phase II units in 1992 (Solar 1991). The facility operated at full capacity until 2003 when steam demand was significantly reduced due to decrease in cathode production and closure of the copper sulfate and precious metal operations. Phase I units were taken out of service and put on care and maintenance status.

Jan 1, 2019

By Alastair Torrance, Italo Onederra, Do Sun Kim, Kush Patel, Gary Cavanough

Reactivity of ammonium nitrate-based explosives is associated with the presence of sulphide in the ground reacting with explosive products and in some instances causing spontaneous reactions which can lead to detonation. This paper explains the mechanism of these reactions, the potential cause of spontaneous detonation and how inhibited explosives prevent the reaction

Jan 1, 2019

By Victor Munoz, Jorge Oliva, Gonzalo Marias

Cerro Vanguardia is a known gold and silver deposit located in the province of Santa Cruz, Argentina. The mine has been in operation since 1998 and is thought to be one of the most important mines in Patagonia. More than 102 epithermal quartz veins have been identified in the area, with variable lengths, thicknesses, orientations and dips that constitute what is possibly one of the most extensive outcropping vein systems on earth.

Jan 1, 2019

By T. M. Klemetti, T. J. Batchler, T. Matthews

From 2013–2017, there were over 1,120 documented injuries, including fourteen fatalities, from ground falls in underground mines in the United States (MSHA 2017). The majority of these ground-fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely used in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded-wire screen as used in underground coal mines by conducting a laboratory testing program using the Mine Roof Simulator (MRS) in NIOSH’s Bruceton Research Center Laboratory in Pittsburgh, PA. The load-displacement characteristics of an 8-ft x 12-ft area of 8-gauge welded-wire screen were evaluated using a test frame designed for testing multiple load-pull locations. In previous tests, load-pull contact was always in the center of the bolted screen section. In this study, larger pull contact areas are used to simulate roof falls. The information obtained in this and similar studies can be used to better understand the loading behavior and surface control capability of roof screen in underground mines. INTRODUCTION AND BACKGROUND The large majority of ground-fall injuries are caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Compton et al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded-wire screen as used in underground coal mines by conducting a laboratory testing program in the Mine Roof Simulator (MRS) in NIOSH’s Bruceton Research Center Laboratory in Pittsburgh, PA. Previous tests to evaluate the performance characteristics of various types of screen have been conducted by the University of Alberta (Tannant, 2001). In this study, the load-displacement properties of welded-wire, chain-link, and expanded-metal mesh were measured by performing full-scale pull tests. A flat steel plate was pulled through a screen test sample that was bolted to a special test frame while the pulling force and mesh displacement were measured. These tests established the general load-displacement behavior of the screen. Peak load capacities and stiffness were determined for each screen type, showing how welded-wire mesh has a much stiffer initial loading response, whereas chain-link and expanded-metal mesh have large displacement capabilities and exhibit significant post-peak ductility.

Jan 1, 2019

By Thomas L. Barkley

My historic auditing of Underground Drilling and Blasting Practices has demonstrated to the author the need for reviews of many mines' procedures in these processes. Poor understanding of the basic principles and practices of the drilling and blasting science in Underground Development Mining has created significant costs to mining operations in many instances.

Jan 1, 2019

By Tristan Worsey, Nathan Rouse

Florida is one of the major limestone producing states in the United States. The state has unique regional geology and groundwater characteristics that require equally unique mining methods to extract limestone for construction materials. In many regions, aggregates quarries operate by drilling and blasting underwater limestone and then digging the muck with large draglines, while in others, mining operations are able to operate above the water table.

Jan 1, 2019

By M. Massinaei, S. Abasi, M. Oliazadeh

Reliable measurement and control of the pulp-froth interface (froth depth) in the flotation columns is critical to achieve the desired metallurgical performance. Shallow froths result in a reduction of grade because of particle entrainment and deep froths reduce recovery because of the drop back of entrained and weak hydrophobic particles to the pulp zone. The cleaner circuit at Miduk copper concentrator consists of three parallel MicrocelTM flotation columns 4 m in diameter and 12 m in height. The interface level of the flotation columns is measured by two pressure sensors located at 1.4 and 2.4 m from the cell lip (in the collection zone). In this study the performance of the level detection system at different operating conditions was evaluated. A calibrated float-ultrasonic location system was used for measuring the actual froth depth. The results indicated that the existing level control system was subject to considerable error. The absolute error was found to be 33.27 cm. This was mainly attributed to the constant set-point value assigned to the froth density (ρf=0.3 g/cm3), which actually varies with the operating conditions. The actual froth density at different conditions was calculated and its average value (ρf=0.12 g/cm3) was re-set in the control system. This resulted in substantial reduction in the level-detecting error. Recommendations for more accurate measurement of the interface level were presented. INTRODUCTION Froth flotation is a complicated process because of many involved variables. One of the most significant controlled variables in the flotation process is the pulp-froth interface (froth depth). The froth depth has a profound influence on the metallurgical performance parameters (i.e. grade and recovery). Shallow froths result in grade reduction because of particle entrainment and deep froths reduce recovery resulted from the drop back of entrained and weak hydrophobic particles to the pulp zone (Finch and Dobby, 1990). Various techniques have been developed for measuring the interface level of the flotation cells in the last few decades. These techniques can be classified as: Techniques based on hydrostatic pressure measurements (Finch & Dobby, 1990), Techniques based on the density gradient (float) (Moys & Finch, 1988), Techniques based on conductivity measurements (Uribe-Salas, 1991), Techniques based on temperature measurements (Moys & Finch, 1989).

Jan 1, 2019

By K. Scalise, M. Teixeira, K. C. Kocsis, J. Parrish

"This paper aims to introduce and discuss a newly developed algorithm, which can be uploaded on smart watches and other mobile devices to inform and protect underground personnel working in hot and humid environments. Using this algorithm, the metabolic rate (M) of a worker can be determined in “real-time”. In addition, besides warning signs and alarm signals emitted by the smart watch, the algorithm has the ability to determine work-rest time periods based on the worker’s physiological parameters (e.g. age, height, weight, gender) and the climatic parameters (Td, Tw, flow velocity). This paper also investigates whether a re-designed auxiliary ventilation system can provide appropriate work conditions in the production stopes. INTRODUCTION An underground environment with high temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to heat-related illnesses such as heat rash, heat cramps, heat exhaustion, and heat stroke. Heat stroke is a serious illness that carries a high risk of fatality, if the underground workers are not immediately treated and the climatic conditions are not corrected (McPherson, 1993). There are two methods used to control the climatic conditions in underground mines: (1) Using ventilation and cooling systems to reduce the thermal stress on the mine workers, and (2) Reducing the heat transferred to the ventilating air from major sources such as: strata, auto-compression, mining equipment, groundwater, blasting, etc. The heat from strata and auto-compression is transferred to the ventilating air at varying degrees, based on factors such as the virgin rock temperature (VRT), the thermal properties of the surrounding rock formations, and the surface air temperature. However, the use of mining equipment and blasting processes can be managed to reduce their contribution to the mines’ overall heat load. To provide appropriate work conditions, selecting the most suitable cooling method depends on the level of heat to be removed, the location of the problem areas, and economic constraints (Brake & Bates, 2002; McPherson, 1993). Because every mine is unique, it is essential to monitor the climatic conditions to select the most appropriate method of cooling. A majority of the time, simply adjusting or re-designing the auxiliary ventilation system can efficiently remove the heat and dilute the contaminants. This may involve moving the ducting system, changing the size of the duct, changing the size of the auxiliary fan, or switching from forcing to an exhausting fan arrangement. If the required air volumes are higher than the existing primary ventilation system can supply, other measures may need to be taken to increase the airflow delivery. This may include regulating the flow in some areas of the mine to increase airflow to the desired area, adding booster fans, or replacing the primary fans."

Jan 1, 2019

By Frank Hirthammer

Productivity, customer relations, and effectiveness of work depend to an ever-increasing extent on a functioning logistics system tailored to the needs of the user. Of course, it is not possible to cover and explain all aspects of the logistical requirements of even a small part of an industry, in a single article. The article speaks specifically about the particularities and differences in the logistical requirements in the explosives sector. Starting with questions of safety, handling and quality up to the legal basis, there are special requirements regarding the logistics in the explosives sector. The results of innovative logistics solutions are presented using three examples from daily work practice.

Jan 1, 2019