Search Documents

By Gobbs C., J. Lam

"The Eagle East project, accessed from the existing and operating Eagle Mine in the Upper Peninsula of Michigan, is an underground base metal project currently in execution by Lundin. This paper will provide an update on several aspects of ventilation including use of a twin-decline access, innovative airflow crossover arrangement and construction ventilation methodology. Integration into existing mine ventilation systems including construction methodology will also be covered. Performance benchmarks and lessons learned are discussed across these topics.INTRODUCTIONLundin has owned and operated the Eagle Mine since 2013. This hard rock underground mine is located in the upper peninsula of Michigan, USA. High-grade nickel ore is mined using sublevel open stoping mining methods and trucked to surface via haul ramp. The mine, having been in production for four years, is nearing the completion of the initial orebody. A satellite orebody 2,000 meters East of the current workings and approximately 900 meters below surface, was identified that could extend operations until 2023. In 2016, Lundin approved the Eagle East project and construction began in 2017 (Lundin Mining Corporation, 2017).Due to proximity to the existing mine, Eagle East will be both accessed and serviced from the existing Eagle Mine. Ventilation at the Eagle Mine uses two fresh air intakes with direct fired combustion heaters; one at the mine portal feeding fresh air into the ramp and one at a fresh air raise located near the Eagle deposit. The primary ventilation circuit is powered on the exhaust air side, with two 700 hp exhaust fans located at a single return air raise. Underground, fresh air is distributed through the main access decline and fresh air raise (FAR) to the production levels and controlled with mechanical regulators on the exhaust side. The exhaust air is collected through return air raises with a collector/transfer drift on 250 Level and then to the surface through a return air raise (RAR)."

Jan 1, 2019

By S. Litke

Elemental sulfur was stockpiled at the Mount Polley Mine for use as a source of sulfuric acid as part of research into leaching copper from oxide ores, but the project did not proceed beyond an initial pilot- scale evaluation. Since placement, the sulfur has oxidized and some sulfuric acid leached into the underlying rock. The reaction of the acid with these underlying materials has been studied as part of an evaluation of the effects of leachate from the pile. The rock underneath the sulfur pile is composed dominantly of primary and secondary alumino-silicates with less than 1% carbonate (calcite) and iron sulfide (pyrite). In its unaltered condition, the rock is classified as non-acid generating. Conceptually, it was expected the sulfuric acid would be neutralized by the rock to varying degrees resulting in a series of pH-controlled weathering fronts progressing from leached near the contact with the sulfur pile (pH <3), to active neutralization by silicates (pH 4–5), to active neutralization by carbonates (pH >7). The rocks underneath the pile were sampled to determine the extent to which the rocks had reacted and their long-term stability after removal of the acid source. INTRODUCTION When rock is blasted and excavated to facilitate mining ore, it is typically placed and stored on the surface in piles. The resulting drainage may have a neutral to basic pH (i.e., non-acidic drainage) or a low pH (i.e., acid rock drainage, ARD) depending on the mineralogy of the rock being stored in the piles. Acid- base accounting (ABA) can be used to characterise the two types of rock: potentially acidic drainage generating (PAG) and not potentially acidic drainage generating (NAG) (Price, 2009). According to Price (2009), NAG is defined as having an excess of neutralization potential (NP) in the rock in the form of calcium carbonate-like minerals when compared to acid potential (AP), i.e., a Neutralization Potential Ratio (NP/AP = NPR) greater than 2.0, whereas PAG is classified as having an excess of AP (i.e., an NPR less than 1.0). This is a conservative estimate and may be slightly modified depending on the mineralogy at specific mine sites. Rock with an NPR of 1–2 is also capable of generating acid (Price, 2009) and, depending on the mineralogy, may also be classified as PAG. Drainage from PAG material can generate acid immediately, or many years after it has been exposed to surface conditions. Disposal techniques depend on the category (i.e., NAG or PAG) and reactivity of the rock stored in the piles.

Jan 1, 2019

By Huilan Yang, Feng He

This paper intends to introduce the development of copper smelting and converting technologies in China in recent years, with a particular emphasis on the introduction of various continuous converting technologies, and moreover, it analyzes the advantages and disadvantages of those technologies, including their impact on the downstream anode refining from different points of view. INTRODUCTION At present, many converting technologies are used in copper pyro-metallurgical plants in China, including Peirce-Smith (PS) converter, flash converting furnace, multi-lance based top blowing, bottom blowing and so on. These technologies have spanned a wide range of time. PS converter technology has been applied in copper smelters for many years and most of the blister copper have been produced by this technology; flash converting technology has been developed since 1990s and been maturely applied in several plants up until now; top blowing and bottom blowing technologies have been revived in China in the past decade and boast good environmental protection performance, energy efficiency, throughput capacity and short process flow. All of the said technologies have reference operations in treating high-grade matte. As more and more attention is paid to environmental protection globally and copper smelters continuously seek for cost reduction, it is necessary to share those converting technologies, especially those new converting technologies derived in China, with copper smelting practitioners in the world. This paper aims to analyze the advantages and disadvantages of various technologies from a macroscopic view and discuss their actual application effects, current developments and future improvements. BRIEF INTRODUCTION OF VARIOUS CONVERTING TECHNOLOGIES IN CHINA China has seen a rapid development in copper smelting industry in the past 30 years and has become the largest gathering place of copper smelters in the world, most of which are operating with PS converting furnace technology, however, with the increasingly strict environmental requirements of the Chinese government in recent years, the low-level pollution issue and the disadvantage of large gas exhaust amount per unit of copper of converting furnaces are particularly prominent.

Jan 1, 2019

By R. Bryce, T. J. Doughty, K. Stoll

Sulfate-impacted mine waters are under regulatory scrutiny to reduce total dissolved solids (TDS). There are several options to reduce TDS. One option is transforming the soluble sulfate into insoluble ettringite. The Water Company LLC (TWC) patented a process for sulfate removal through ettringite formation by reacting directly with metallic aluminum. Freeport-McMoRan (FMI) and TWC have collaborated to design, build and operate a 10-gallon-per-minute (gpm) ettringite pilot plant to establish reagent consumption, plant availability and full-scale design criteria. Using metallic aluminum as the primary aluminum source for ettringite precipitation eliminates the addition of other ions, resulting in significant demineralization. The pilot plant achieved greater than 98% water recovery, greater than 90% reagent efficiencies and maintained reactor sulfate levels below 250ppm. BACKGROUND Ettringite is a hydrated calcium, aluminum, sulfate mineral with the following formula: Sulfate-impacted mine waters are under regulatory scrutiny to reduce total dissolved solids (TDS). There are several options to reduce TDS. One option is transforming the soluble sulfate into insoluble ettringite. The Water Company LLC (TWC) patented a process for sulfate removal through ettringite formation by reacting directly with metallic aluminum. Freeport-McMoRan (FMI) and TWC have collaborated to design, build and operate a 10-gallon-per-minute (gpm) ettringite pilot plant to establish reagent consumption, plant availability and full-scale design criteria. Using metallic aluminum as the primary aluminum source for ettringite precipitation eliminates the addition of other ions, resulting in significant demineralization. The pilot plant achieved greater than 98% water recovery, greater than 90% reagent efficiencies and maintained reactor sulfate levels below 250ppm. BACKGROUND Ettringite is a hydrated calcium, aluminum, sulfate mineral with the following formula: Ca6Al2(SO4)3(OH)12•26H2O Ettringite readily precipitates in high pH water and by doing so, removes sulfate from impacted waters. The SAVMIN process, piloted in South Africa, is one method to produce ettringite. In this process, aluminum hydroxide is the aluminum source. The Cost Effective Sulfate Removal (CESR) process is similar to SAVMIN, but uses a proprietary aluminum source instead of aluminum hydroxide. Outotec and Veolia also have their own versions of the process using their specialized process equipment. TWC patented a version of ettringite precipitation using metallic aluminum as the aluminum source for ettringite formation. The benefit of using aluminum metal is that no additional ions are added to the process. At high pH, the raw aluminum corrodes in water causing hydrogen gas generation as the water is chemically reduced. This reaction is shown below:

Jan 1, 2019

By T. Lux, H. -J. Krassnig, I. Filzwieser, E. Hecker, R. Degel, A. Filzwieser

Non-ferrous metals find their applications in smartphones, tablets and computers. These materials with their particular properties are the basis of our modern life. SMS group is well prepared for this huge market and for growing future challenges. A large contribution here is the new joint venture PolyMet Solutions that was founded by SMS group and Mettop, an Austrian engineering company, with the objective to develop new technical solutions for the primary copper production lines as well as for non-ferrous metals starting with the primary smelting of concentrate and ending with the electrolysis. PolyMet Solutions provides the process know-how whereas SMS group supplies the plants and equipment and Mettop the key components. SMS group and Mettop also cooperate in the field of tankhouse technology. Together with Montanwerke Brixlegg AG, Mettop has developed together with a parallel flow technology (METTOP-BRX Technology), allowing a current efficiency of above 98 % at a current density of 420 A/m², which is a milestone in copper electrolysis. For the secondary copper production route, SMS group and PolyMet Solutions developed an innovative refining furnace (PolyRefine) for the smelting and refining of copper scrap. The refined copper is directly charged to the Contirod line to produce copper rods and wires. The innovative cooling solutions of SMS and PolyMet Solutions come into play where furnaces have to stand the highest loads and stresses, for instance in areas of very high temperatures or temperature fluctuations, aggressive exhaust gases and slags, or at critical spots such as taphole areas. Custom-tailored cooling systems for furnace vessels make sure varying loads are compensated in a targeted and effective manner. The solutions include air cooling, spray cooling, cooling technologies with integrated copper elements such as CFM (Composite Furnace Modular) cooling systems, plate and finger coolers. The major innovation in the field of furnace cooling is the ILTEC (Ionic Liquid Cooling) Technology which paves the way for increased plant safety. This revolutionary, patented cooling technology is jointly marketed by Mettop and SMS group. It permits water-free cooling to be implemented and thus makes operation safe wherever it is applied. INTRODUCTION Non-ferrous metals or NF metals are changing the world. There is no modern industrial sector that can do without these valuable metals. Non-ferrous metals find their applications in smartphones, tablets and computers. These materials with their particular properties are the basis of our modern life. The importance of the non-ferrous metals market is reflected by two figures. In 2018, the production of non-ferrous metals was worth more than 237 billion Euros. This contrasts with 255 billion Euros of the value of iron and ferro- alloy production in the same year (International Organizing Comittee for the World Mining Congresses, 2018). Hence, the NF metal industry is almost as important as the iron and steel industry. SMS group is well prepared for this huge market and for growing future challenges. A large contribution here is the new joint venture PolyMet Solutions that was founded by SMS group and Mettop, an Austrian engineering company, with the objective to develop new technical solutions and to enhance customer value. The prices of nearly all metals have come under pressure during the past few years. Therefore, competitive technologies are regarded a crucial factor to achieve success in this critical market situation respectively to stabilize the market position.

Jan 1, 2019

By Remi Proulx, Ruilin Yang

The effectiveness of presplit in soft or fractured ground is hard to visualize or quantify. There have been many attempts by the blasting community to measure and quantify the effectiveness of presplit blasts. Various methods have been adapted by different researchers, and the results are debatable.

Jan 1, 2019

By D. Runnels, A. Allaire, J. Torrealba-Vargas

Data mining and modelling of operational data involves the discovery of patterns in large datasets for future use in benchmarking and plant optimization. The modern pattern of discovery in large data sets involves statistical techniques, machine learning and new visualization tools. Former examples of data mining are revisited and presented in this document. INTRODUCTION A network of enthusiastic and active professionals is currently developing and maintaining several open source statistical software tools (packages) for data analysis (example Rstudio, Orange, Spyder, etc.). The advantages of the open source software philosophy are the fast development and testing of the solutions presented to the community. Books and support are available for each software application. Since each modern work activity generates massive amounts of data, it is attractive to learn and test those available tools considering that we are at the door of the new work revolution coined as “Mine 4.0”. Data mining involves collecting large datasets, the preparation and cleaning of a dataset (term named data wrangling), the uploading of the data to a database program capable of handling big datasets, the development of prediction models and the presentation of the results. Machine learning techniques help to develop mathematical models and algorithms that could be used to improve the performance on a specific task. Mine operations are producing an incredible amount of data each day and the need to analyze those results seems to be impossible due to the lack of time, as well as the lack of skills to investigate the data collected. If we add to this the traditional habit of working in silos, an additional challenge is to consolidate databases from different departments in search of trends that could help to optimize production.

Jan 1, 2019

By David Hanson, Sean Warren, Chaparral Berry

"Coal bumps, also referred to as dynamic failure events or coal bursts (Lawson, Weakley, and Miller, 2016), continue to be a hazard in underground coal mines. While current design methods have significantly reduced the occurrence of coal bumps, they have not been completely eliminated. This paper investigates a correlation between coal compositional components, coal molecular structure, and probability of coal bumps in an effort to deepen understanding of coal behavior in an effort to reduce hazards in underground coal mines.Samples from the Penn State Office of Coal (PSOC) Department of Energy Coal Samples (DECS) were obtained for Fourier Transform Infrared Spectroscopy (FTIR) analysis using the KBr pellet method. Peaks indicative of the coal molecular structures were obtained using spectral integration software. These data, combined with published elemental data, were compared to historic bump occurrence in order to establish a possible correlation. Finally, results based on multivariate analysis of the elemental and FTIR data with bump status as the dependent variable suggest that elemental sulfur and molecular structure can be used as an indicator of bump susceptibility within the sample set considered.INTRODUCTIONThe study of coal requires consideration of multiple variables: percentages of organic and inorganic components, organic component origins, coal age, pore structure, cleat density, elemental composition, etc. Examining coal in situ increases the number of variables, such as coal depth, seam thickness, surrounding stratigraphy, and so forth. This collection of variables influences the subsequent behavior of coal simultaneously, and weighing their relative impact is a challenge for researchers. “A problem never exists in isolation; it is surrounded by other problems in space and time” (Ackoff, 1956). Having a substance such as coal that we know so much about, and yet so little, we have to ask what can be learned.An experimental study using Fourier Transform Infrared Spectroscopy (FTIR) was undertaken to determine if the chemical structure of coal contains information which may lead to a better understanding of triggers or attributes which may, in turn, lead to an increased probability of a dynamic failure event. While a full analysis of the factors driving dynamic failure are beyond the scope of this study, it is possible that a better understanding of the chemical structure of coal will lead to an increased knowledge of its inherent behavior, including its propensity to burst."

Jan 1, 2019

By B. McHenry, A. E. Wraith, P. J. Mackey

The Wallaroo smelter on the Yorke Peninsula, South Australia commenced smelting operations in 1861 treating ores from the nearby Moonta and Kadina mines. The plant expanded and modernized on several occasions and was a leader in the successful introduction of new technology to improve operations. It operated continuously until 1923 when local mines became exhausted; in the closing stages of the 19th century it was the largest copper smelter in the world outside of those in Swansea, Wales. In 1892 a small electrolytic refinery was established at Wallaroo, the first in Australia, based on principles developed by Elkington at Pembrey, Wales in 1869. The Wallaroo refinery was specifically built to recover gold and silver from copper produced by smelting gold-containing feed materials shipped from Western Australia. This first venture into electrolytic refining was replaced in 1903 by a somewhat larger refinery which, although modest in size for its time, with a capacity of about 1000 tonnes of cathode copper per year, was very productive in precious metals. Anode copper was produced by an updated version of the reverberatory-based Welsh process until 1910 when barrel-type pneumatic converters were introduced based on American practice; subsequently, anodes were cast by tapping the precious-metals rich "bottoms" portion of converter copper as produced at about one-fifth into the copper blow. The present paper describes the Wallaroo refinery, its anode supply and products, supported by initial observations on a sample of a Wallaroo cathode held in the collection of the South Australia Museum, Adelaide SA, Australia. INTRODUCTION Australia ranked 6th in the world for copper mine production in 2018, with an output of 918,000 tonnes of mined copper, after Chile, Peru, Congo, China and the USA; about 40% of Australian mined copper was smelted in the country. Interestingly, the world ranking of Australia in mined copper has, with a few variations, remained about the same for more than 100 years – of interest, it was also the 6th largest country for copper production at 21,089 tonnes in 1899. At that time, all or most of the copper was smelted in the country (Mackey, 2016). Copper was first discovered in Australia in 1842 in South Australia not far from Adelaide; additional copper discoveries in the region soon followed. At first, copper ore was shipped to Swansea, Wales for smelting (Bampton, 2003). However, in addition to the long, 150 day one-way sea passage, it seems Welsh smelters preferred higher grade of ores – these aspects and likely a mood in the new colony to be independent of Swansea (Evans, 2014) evidently encouraged local smelting at the mine sites using small, Welsh-type reverberatory furnaces fired with hardwood as fuel and operated by Welsh and Cornish migrants. The first large copper smelter in Australia commenced in 1848 at Bremer, near Callington some 60 km east of Adelaide. With larger discoveries on Yorke Peninsula, the Wallaroo copper smelter at Wallaroo Bay on the west coast of the peninsula commenced operations in 1861 (Bell & McCarthy, 2008). Thus began one of the most successful, and in its day, one of the most advanced and innovative plants in Australia if not the world. In the late 1860s, it was considered one of the largest copper smelters in the world (Bell & McCarthy, 2008)

Jan 1, 2019

By Michel Ruel

Most plants do not track how their systems perform. Optimization is the easiest way to benefit from your control systems. We suggest an approach in four phases. The first phase is to assess all equipment to determine the performances for instruments, valves, variable speed drives, and other equipment. The second phase is to remediate instrumentation problems, including the ones pertaining to valves, variable speed drives, analyzers, transmitters. When equipment is in order, loops are put back in automatic mode. If a loop oscillates, use standard default values for this type of loop. The third phase consists in validating the control strategies, properly configuring the systems (control system, programs and parameters, HMI, alarms), and then tuning the loops and control strategies. The fourth phase consists in analyzing the process and expected performances in order to optimize the control loops and control strategies. If performance is not sufficient, a decision tree will be presented to determine the right approach: advanced regulatory control, model predictive control, or fuzzy logic control. Once all steps have been completed, control performance monitoring software is used to sustain the results and pinpoint equipment or loops not performing as stated. Alarm management and rationalization could also be performed after auditing the alarm system, if needed. Examples from plants will be used to demonstrate how this step-by-step method is applied and produces results. INTRODUCTION Maximizing what you already have is the best investment to remain competitive. This article aims to show the benefits of a systematic approach using modern tools to improve plant performance. We at BBA suggest dividing the work in four phases, and a subsequent phase can begin when the previous one has progressed: Assess, Remediate, Stabilize, Optimize, or add advanced control. This approach has been successfully applied to several sites. Examples and illustrations from these plants demonstrate how this step-by-step method is applied and produces results. Under the BBA method, there are four questions to answer before proceeding to the next step. For each control strategy, you should ask the following questions: Assessment: Does it work? Remediation: Do you use it? Stabilization: Is it stable? Optimization: Does it perform? Do you need advanced control?

Jan 1, 2019

By J-N. Oyourou, R. McCrindle, C. J. S. Fourie

"Many mines in South Africa were inappropriately closed and left unattended during the last century. These old mines are potential sources of environmental pollution and may pose a health risk to local populations, since the surrounds contain elevated levels of toxic elements. Soil from the old Edendale lead mine property in Mamelodi Extension 11, east of Pretoria, which was suspected to be contaminated with lead, was analysed. The mine, which primarily extracted galena, was decommissioned in 1938. During this study, the old mine property and surrounds were screened for zinc and lead using a field-portable X-ray fluorescence (pXRF) spectrometer. The metal concentrations, which ranged from 18 to 7 300 mg/kg for zinc and from 50 to 21 000 mg/kg, for lead, were plotted together with the GPS coordinates to produce a concentration distribution map for lead and zinc. This map revealed three anomalies of unacceptably high concentrations, possibly corresponding to areas where ore had been piled or dumped to waste from the old mine. Thirty-six of the soil samples that were analysed by pXRF on site were selected and analysed in the laboratory using inductively coupled plasmaoptical emission spectrometry (ICP-OES) for verification purposes. The zinc and lead concentrations obtained from the two analytical methods were compared using linear regression analysis. Excellent correlation was obtained between the results from the two methods (r2 = 0.99 for zinc and r2 = 0.95 for lead). IntroductionEarly economic development in South Africa was based mainly on mining. However, these activities left a legacy of approximately 6 000 improperly closed mines scattered throughout the country (SAI, 2009; van Schie, 2012). Due to their proximity to settlements, these abandoned mines may pose a potential health risk to humans and an environmental hazard. Mining activities generate large amounts of waste, mostly in the form of overburden and process tailings, which often contain high concentrations of toxic elements. Bioavailable toxic elements can contaminate crops growing in the polluted area (Kala, 2010; Marwa, Meharg, and Rice, 2012) or eventually migrate and detrimentally affect the groundwater (Rösner and van Schalkwyk, 2000). Moreover, sulfides accumulated in mine waste generate acid minewater (Rösner and van Schalkwyk 2000). Unfortunately, owners of mines, closed before the promulgation of the Minerals Act more than twenty years ago (Act 50 of 1991), avoided the compulsory rehabilitation of the environment enforced by this legislation. Toxic elements, such as lead, which were confined within ores, may become exposed through mining and are therefore more easily mobilized within the environment. Elements essential to human and plant metabolism, such as zinc, when exposed by mining activities, may become hazardous due to elevated concentrations (Aslibekan and Moles, 2003; Wuana and Okiemen, 2011). Humans exposed to potentially toxic metals may experience harmful effects as discussed elsewhere (Nriagu and Pacynar, 1988; Wayne and Ming-Ho, 2005)."

Jan 1, 2019

By Mehmet Canbazoglu, Kaarlo Haavanlammi, Hannu Laitala

Cobalt is currently a critical metal because of the increasing number of electrical vehicles forecast for production. Copper and zinc are base metals that are used in many everyday applications, including vehicle production. Eti Bakir Co. Mazidagi Phosphate Plants in the Mazidagi district of Mardin, Turkey is a multi-product facility that produces cobalt, copper, and zinc, as well as fertilizers, from the roaster calcine. Roaster off gas is treated in a sulfuric acid plant (SAP) and the acid itself is utilized in fertilizer production. The comminution circuit, roaster, SAP, and calcine leaching process were developed by Outotec and integrated with the fertilizer production process implemented by Eti Bakir A.Ş. This paper describes the hydrometallurgical calcine leaching process used at the plant, with a focus on the oxidative pressure leaching of the cobalt, zinc, and copper-containing calcine. The cold and hot commissioning phases of the pressure leaching autoclave start-up are discussed together with experiences from the ramp-up period. The production processes of the copper cathode and cobalt and zinc-containing salts are also presented together with some of the plant’s operating parameters. INTRODUCTION The ETI Bakir A.S. fertilizer plant, Turkey, is located in Mardin Province near the border with Syria, (Figure 1). The leaching plant project was started in 2012. The purpose of the plant is to separate the valuable metals from the calcine produced by the pyrite roasters, which are used to produce a SO2 containing gas for the new sulfuric acid plant. Fertilizer production requires sulfuric acid, and for this reason a sulfuric acid plant was built; customer already had access to pyrite concentrate, which is used as the roaster feed. During the engineering phase of the roaster and acid plants it was noticed that the roasted calcine contained considerable amounts of valuable metals like cobalt, copper, and zinc. To recover these metals, a calcine leaching process was developed at the Outotec Research Center in Pori, Finland. The main process connections of the Mazidagi site are shown in Figure 2.

Jan 1, 2019

By L. Van Wyk, J. Fernandez, J. Suarez, L. J. Diaz, A. Uria, D. Breeuwer

"Ventilation is an essential component of any underground mine, playing a vital role in ensuring the health and safety of workers, and a mine’s continuous operation. At a time when mining companies are increasingly having to move to deeper underground operations in pursuit of high-grade ore-bodies, the search is on for more efficient ventilation systems that will allow mining to be carried out at even deeper levels whilst ensuring the protection of workers and the maximisation of productivity through temperature management and the lowering of energy costs. Mining companies today are looking for innovative ways to deliver new technologies and procedures to enhance their mine’s profitability. Energy consumption by mine ventilation systems is higher than ever due to stringent specifications of underground equipment (primarily combustion engine emissions), air quality standards and mining at deeper levels which all require more powerful ventilation systems. With energy costs associated with operating ventilation systems being a mine’s second-highest cost of production after labour, finding the optimal ventilation solution is critical to a mine’s performance. Proper fan design remains a major factor in reducing capital expenditures (CAPEX) and operational expenditures (OPEX), which means that there are compelling reasons for making use of comprehensive factory testing at full power before fans are dispatched to site to simulate the mine’s current and future design requirements, and thus verify the fan’s effectiveness in ‘real’ conditions.INTRODUCTION A primary mine fan is considered the heartbeat of the entire mine ventilation system, drawing fresh air from the surface and providing a safe environment for miners. A ventilation system’s lack of performance often leads to a reduction in acceptable air quality levels for underground working operations and can potentially have an adverse impact on production rates."

Jan 1, 2019

By C. Matthews, A. Vo

"Australia is one of the world’s leading exporters of bulk commodities and the extensive use of sampling equipment is key to the successful management of each mining operation. At the process plant, without a full understanding of the feed, product and tails, it is impossible to fully optimise the performance of the plant, such that the metallurgical balance is often open to error. At the port, a statistically correct, bias free and compliant sampling system is crucial to ensuring exported minerals are reflective of their true value and to avoid penalties. Over the last decade, as a result of the iron ore boom, there has been high demand for reliable, representative and standard compliant solids sample systems in Australia. This paper reviews several solids sampling applications at Australian mine sites, the challenges and experience gained and how the implementation of reliable representative sampling systems has provided better understanding of plant process performance, improved plant control and overall benefits to the operations.INTRODUCTION Mining is the primary contributor to the Australian economy with Australia ranking in the top 4 in economic resources for 21 primary industrial minerals in 2016 (Britt, et al., 2017). Australia is one of the world leaders in the export of the majority of its commodities including gold, copper and iron ore (Britt, et al., 2017). Therefore, a suitable and standard compliant sampling system is essential for evaluating plant performance and content verification. At the mine and at the port, the larger iron ore miners in Australia have developed stockpile models to predict the grade of their ore down to individual blocks of the stockpile. This allows the miner to create the right blend of material for sale to their customers and ensures they are not underselling their product or at risk of penalties for impurities or low grade. As an example, the average difference between the benchmark 62% Fe and low grade 58% Fe fines at the time of this report averaged US $30/tonne according to the Metal Bulletin Iron Ore Index. At a shipload of 180kt this would be a variation of US $5.4M. Whilst this is an extreme example, it highlights the economic importance of producing the correct grade product and a recognised representative sample of said product."

Jan 1, 2019

By A. Romero

"Most underground mines require heating or cooling systems to meet health and safety standards in the working areas. In regions where daily or seasonal fluctuations of environmental conditions exist, these systems tend to be over-sized and operate at low average load factors, which increase both investment and operating costs. One possible approach to reduce the temperature variations of the fresh air supplied to the mine, and so reducing the investment in large heating or cooling systems, is to use rock as a thermal regenerator or thermal storage system. Packed rock beds act as thermal inertial units, damping the atmospheric temperature oscillations to provide a more constant fresh air temperature. However, although regenerators exist in some mines, and packed bed rocks have been studied in detail in solar thermal power applications, there is a lack of tools to design new and sufficiently large storage systems of this kind. This work fills the existing gap by presenting a methodology to design and evaluate the impact on the ventilation systems of these regenerators. The method is validated using existing rock bed systems found in the literature and illustrates possible designs for small and large size regenerators in both hot and cold climates.1 INTRODUCTION “ It is quite amazing how often answers to extremely complicated problems can be obtained in this way, by using greatly simplified models of the real situation for the purpose of calculation.” Whiller, A. in private communication to J. S. Stachulak (1989). Motivation Most underground mines located in regions with extreme climatic conditions require the thermal pre-treatment of the fresh ventilation airflows, whether for heating or cooling. Heating commonly is needed in sites with sub-zero temperatures and is usually effected by direct or indirect burning of natural gas or propane. Alternatively, cooling is required in areas with hot temperatures, or in mines with high underground thermal loads where the fresh air at ambient temperature cannot provide enough refrigeration. Thus, when the ambient air conditions cannot provide by itself enough thermal power to ensure safe underground working conditions, a heating or cooling plant is required, which involves a considerable equipment and operation cost."

Jan 1, 2019

By P. Nayak

"Comminution is an energy intensive and expensive process consuming approximately 40-50% of the total processing costs in a mining operation. This process poses an even greater challenge with gold ores due to their low elemental concentration and small particle size. Over 99.9% of the ore fed to the mill is waste which must be removed during the ore processing stage. Preconcentrating the Run of Mine (ROM) ore before feeding the mill will result in significant cost savings. In partnership with Sacré-Davey Engineering, Agnico Eagle Mines Limited identified this opportunity and is currently evaluating the implementation of sorting technology to preconcentrate the ore or upgrade the waste material at its operations. This paper will discuss the steps adopted by Agnico Eagle in the evaluation and installation of sorting technology at its operations. Since the Company has a large portfolio of operations, the first step in the project was to shortlist the operations that had the highest probability for successful application of the technology. Following this, the top three operations were selected for bench scale evaluation. The projects which showed the most economic potential were then considered for detailed evaluation and pilot plant installations. This paper provides an insight into the methodology followed by Agnico Eagle and Sacré-Davey in the evaluation of the technology.INTRODUCTION The benefits of ore sorting technology are being increasingly understood by the mining industry today. The application of ore sorting in gold mining is attractive due to the nature of the mineral distribution. The presence of high value minerals distributed in an extremely small mass of the ROM ore creates a tremendous opportunity for preconcentration with ore sorting. Since Agnico Eagle currently has a portfolio of eight operating mines and numerous development projects and exploration properties, the challenge was to identify the deposits which had the most favourable mineralogy and grade distribution for successful ore sorting. The success of ore sorting is mostly based on the minerals present in the deposit and the grade distribution. The minerals signify the amenability of the deposit for ore sorting and the kind of sensing technology to be used. On the other hand, the grade distribution demonstrates the amount of material that can be rejected without losing value. In order to understand a deposit’s characteristics, it is important to examine the sample’s behaviour with various sensors and then assay it to know its actual value. It is a common practice in the mining industry to document assay value of drill cores and/or material feeding in and out of the mill. However, those VALUES (are insufficient to understand the grade variability on a granular basis. To capture the ore variability in very high resolution and significantly improve the selectivity of the material feeding the mill, it is vital to assay the samples on a rock-by-rock basis, as this is the level of resolution which will be examined by the ore sorter during sorting. A careful and elaborate procedure was followed in evaluating the technology at Agnico Eagle’s operations which is discussed in this paper."

Jan 1, 2019

By Thomas. Lisa, Mark Coleman

Schenck Process is an established customer-driven solutions provider, utilising its knowledge, expertise and technologies to transform production processes. Operating across several industries Schenck Process have developed quality solutions from their range of equipment to solve problems and fill holes in other people’s processes. In the non-ferrous metals industries Schenck Process have been using their Clyde Brand solutions in Pneumatic Transport to solve problems on smelter sites for a number of years, handling of concentrates, additives and metallurgical dusts. Working alongside clients around the world they have developed a number of dust handling systems for flash furnaces from New Boliden, through Codelco to PASAR. Solving handling issues in dust collection has proved to suit Schenck Process range of equipment well and now a series of solutions are available. Solutions have been developed to handle materials up to 600°C and can convey over 1 km. Conveying to remote location for disposal, injecting directly into a furnace through lances, return to furnace burner feed, or deliver and dose into leaching reactors, Schenck Process are ready to ‘make processes work’. Historic solutions at New Boliden and Codelco demonstrate a range of material application and the long term performance of the equipment. Recent installations at Pasar utilise the Schenck new ProPhaseTM equipment and handle the Waste Heat Boiler and ESP dusts directly and simplify the dust train. The paper will seek to show how this equipment can bring benefit in handling high temperature materials directly and eliminate several traditional steps that are often unreliable. The systems can be paired with Schenck Process new PHASiQTM and STREAMiQTM control systems which are complete PC, HMI, PLC, Interface system with full SCADA, Data Storage and IoT ready remote interrogation and support available. Installed in this challenging environment the systems are ready for smelter use. The systems can be also joined to our new E-nizingTM web portal. A perfect partnership to deliver the trend in ‘Big Data’ while providing visibility and off site support. The paper will show how these systems can deliver reliable equipment and remote support for these often isolated sites as well as delivering rapid return on investment. This paper discusses a step change in simplifying Flash Furnace Dust handling which Schenck believes shows the truth of Schenck Process Solutions claim that ‘we make processes work’.

Jan 1, 2019

By J. L. Bellanca, L. R. Swanson

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not constitute endorsement by NIOSH. ABSTRACT Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which presents an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders' evaluations. The study includes considerations for safe technology integration. INTRODUCTION Striking, pinning, and crushing accidents related to mobile machines continue to be a major concern in underground coal mining. The National Institute for Occupational Safety and Health (NIOSH) linked 22 of the 75 underground mine fatalities reported between 2011 and 2015 to power haulage [1]. The Mine Safety and Health Administration (MSHA) asserts that proximity detection systems for mobile machines (mobile PDSs) could help to prevent these types of fatal injuries [2]. Mobile PDSs use a collision avoidance technology that allows the mine to establish hazard zones and employ electromagnetic sensors to detect workers equipped with a miner-wearable component (MWC) working near these mining machines. The authors characterize a mobile PDS as an automated technology, because—in line with Lee & See’s [3] definition of automation—a mobile PDS actively “selects data, transforms information, makes decisions, or controls processes” (p. 50). When the system detects workers in the established hazard zones, it issues alerts and slows or stops the mobile machine. Even though a mobile PDS may be a viable and promising safety solution, there are still a number of questions regarding how well this automated technology will fit with mining tasks and conditions. Using a mixed-methods approach, the current study explored factors that influence the fit of mobile PDSs in the underground mining environment.

Jan 1, 2019

By J. L. Wilson

"Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. To assist the new operators, the SAG Mill at B2Gold’s Fekola Mine in Mali needed a robust control that could handle load changes and unmeasured disturbances with minimal operator intervention. With modern Distributed Control Systems (DCS) powerful enough to run advanced control, they often have Model Predictive Control (MPC) blocks built in or available as an “add-on” license, and thus MPC can be readily implemented within the modern concentrator with a relatively low added capital cost. This paper discusses an implementation of two single output MPC controllers to control the SAG Mill at Fekola. This was implemented using the existing signals and advanced control blocks available to the installed DCS.INTRODUCTION Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is that by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. The next step the operator may take may be to cut back the feed rate, or production until the SAG is once again stable. With this sudden reaction comes an abrupt change in SAG rotational speed and power consumption that sends a surge of material down the circuit as the mill suddenly ejects more pulp. Furthermore, choosing a higher rotational speed can lead to higher than normal liner wear as the cataract overshoots the toe of the charge and impacts the liners. After start-up at B2Gold’s Fekola Gold Mine in 2017, the SAG mill was being controlled manually. The SAG rotational speed was adjusted manually by the operator in step changes depending on whether the SAG bearing pressure was increasing, decreasing or stable. During this time of manual control, the SAG fresh feed rate was also adjusted to a tonnage setpoint with a PID controller. Generally, the SAG fresh feed rate setpoint was kept at a target value, but then the feed rate was throttled back if the SAG mill or grinding circuit showed signs of overloading. The extra challenges were that the operators had limited experience and were concurrently learning how the plant operated. Also, they were also occupied with managing situations in the rest of the plant. Often their attention was drawn away from the SAG mill and during that time, the SAG Mill would load up before they could react."

Jan 1, 2019

By D. Beneteau, L. Feldman, D. Milne, A. Hyett, G. Snell

"Behaviour of rebar bolts subjected to combined shear and bending in underground potash mining applications is not well understood. An experimental investigation compared load applied to resin-grouted No. 25 metric rebar to theoretical load, calculated using elastic bending theory. Distributed optical sensing (fibre optic) technology allowed axial strain measurements at 1.25 mm increments along the length of rebar. Experimental procedure, data processing methods, and equipment improvements are needed for field applications of optical sensing technology. Goals were to adopt procedures for instrumenting rebar bolts, conduct tests, and develop data interpretation methods to measure field deformations and loads. ¦ KEYWORDS Fibre optic, Potash mine, Rebar bolts, Transverse load testing RÉSUMÉ On appréhende encore mal le comportement des boulons d’ancrage pour barres d’armature soumis au cisaillement et au cintrage pour un usage dans des mines de potasse souterraines. Une étude expérimentale compare la charge appliquée aux barres d’armature de diamètre n° 25 (25 mm en mesure métrique) enduites de résine époxy à la charge théorique, calculée à l’aide de la théorie de la flexion élastique. La technologie de détection optique distribuée (fibre optique) a permis d’effectuer des mesures de la contrainte axiale à des différentielles de 1,25 mm sur toute la longueur de la barre d’armature. Pour des applications sur le terrain de la technologie de détection optique, il faut envisager une procédure expérimentale, des méthodes de traitement de données et une amélioration de l’équipement. Les objectifs établis consistent à adopter des procédures d’instrumentation des boulons d’ancrage pour barres d’armature, à effectuer des essais et à mettre au point des méthodes d’interprétation des données pour mesurer les déformations et les charges sur le site. ¦ MOTS CLÉS boulons d’ancrage pour barres d’armature, essai par charge transversale, fibre optique, mine de potasseINTRODUCTION Resin grouted rebar bolts are commonly used in potash mines in the province of Saskatchewan, Canada, in areas where shear deformation is observed in the rock, or where potentially unstable ground is present, including locations such as clay seams. Opportunities to observe deformations of rebar, as shown in Figure 1, are rare because it is unusual in underground potash mining to excavate supported ground. In this situation, a block of potash containing a rebar bolt had failed."

Jan 1, 2019