Search Documents

By Muhammet Mustafa Kahraman

Despite technological advancements and organizational adjustments, lost time accidents are major issues in occupational safety. However, there is very limited work that focuses on variables influencing days lost as a result of occupational accidents. In this study, decision tree and artificial neural network methods were used as machine learning techniques to investigate the impact of factors on accident lost day duration. Degree of injury, worker age, and worker activity were found to be the top three variables impacting loss of time from work. It was also identified that the mining method, location, and nature of injury had a moderate influence on duration lost due to occupational accidents. However, worker experience and ore type did not have any significant impact on the duration, which is an unexpected result. These results confirmed that some accident factors that might have a large influence on the number of mine accidents can be less critical when it comes to accident lost day duration.

Feb 3, 2021

By J. Miller, B. Slaker, M. M. Sears, G. Rashed

Ground falls represent a significant hazard at underground mines in the stone, sand, and gravel (SSG) sector in the USA. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are currently conducting detailed investigations into the complex loading conditions at underground stone mines operating in challenging conditions. This paper presents the application of numerical modeling to analyze pillar and roof stability at a dipping underground limestone mine. A validated numerical model was used to explore the potential behavior of the pillars and roof as loading conditions change. The validated model was used to compare changes in mining sequence, overburden depth, and the in situ stress field. This will allow mine operators and engineers to have a better idea of the conditions that could be encountered as mining progresses. Results from the numerical modeling indicate that roof displacement more than doubles as the vertical stress increases from 10 MPa (1450 psi) to 19 MPa (2750 psi) when the maximum and minimum horizontal stresses were 41 MPa (5950 psi) and 22 MPa (3190 psi), respectively. Consequently, as the pillar load increases, the safety factor of the pillars is projected to decrease by about 25%. The impact of the practical application of numerical models can result in a reduction of ground-fall accidents and injuries as well as generally safer working conditions.

Feb 2, 2021

By J. Zhang, A. J. S. Spearing, L. Ma

Ore deposits are becoming more complex to mine as a result of the exhaustion of surface and other easily mined deposits. There is also increasing socio-political pressure to design more environmentally sound, sustainable, and safe mining practices. Wang and Ma designed a mining method for coal, similar to a modified drift and fill using a continuous miner to take sequential cuts (rooms) that are subsequently backfilled. The authors have modified the concept to make it more autonomous, safer, and less costly using highwall coal mining techniques, modified and adapted for underground applications. The method is more flexible than longwall mining and the percentage extraction would seem to be in the same range. In addition because of the backfilling, surface subsidence would not be a major issue and could be more effectively managed.

Feb 2, 2021

By J. S. Contreras, E. Córdova, I. Gottreux, A. Anani, A. Ferrada

Cave mining is an underground mass mining technique. The largest projects, which are known as ‘super caves’, produce hundreds of thousands of tons of ore per day, which involves large footprints with considerable column height, and have a life of mine of over 20-40 years. These operations are typically located deep, under high stresses and in competent rock masses, making initiation and propagation of the caving process harder to manage. These challenges must be confronted by optimizing the fragmentation of the orebody to achieve smaller size blocks that will result in consistent caving and improved flow of the ore from the drawpoints. To achieve better performance from the drawpoints, preconditioning is applied to fragment and damage the material required to cave. We present a proposed design for preconditioning in underground mines, considering the challenges that these large-scale mines are already facing, based on a comprehensive analysis of current design parameters, case studies, and sensitivity analyses using numerical models.

Feb 2, 2021

By S. Schutte, J. Pelders

Worker participation in equipment development can result in improved user acceptance and product quality. This paper focuses on worker engagement in equipment development processes in the South African minerals sector. Qualitative data was gathered during interviews with original equipment manufacturers (OEMs) and industry experts. A lack of inclusion in equipment design from workers from all organizational levels in mines was reported. Meanwhile, the historical context and workplace culture of the mining industry (including leadership, trust, training, performance, and remuneration factors) were evident barriers to the implementation of new technology. Worker engagement processes should include securing management commitment, creating multidisciplinary teams, effective facilitation, shared understanding of needs, training and development, and iterative design. Human-centred design approaches and independent platforms for engagement on equipment design requirements are recommended.

Feb 2, 2021

By A. M. Garbers-Craig, T. Coetsee, T. M. Nemavhola

Accretions often form in furnaces when slag and charge materials attach to the refractory wall and build up over time. Accretion formation is usually unwanted because it reduces the working volume of the reactor and hinders material flow through the reactor. However, in some instances a thin, stable accretion layer may be desirable to protect the underlying refractory material. In order to prevent and/or manage accretion formation, it is important to understand the underlying principles of this phenomenon in the particular reactor. Excessive accretion formation hampered production at the Exxaro FerroAlloys ferrosilicon melting and atomization plant. This plant uses induction furnaces in which a 15% silicon-iron alloy is produced by batch smelting a mixture of ferrosilicon of 75%Si grade and low-carbon steel. The molten ferrosilicon alloy is then gas-atomized to a powdered product for use as a dense medium in mineral processing plants. The objective of this study was to investigate the effect of different impurity levels in the ferrosilicon feed material on the extent of accretion formation as well as the effect on the accretion properties, which influence the ease of accretion removal upon furnace shut-down. Refractory and accretion samples were collected after a furnace shut-down and characterized using X-ray diffraction and scanning electron microscopy–energy dispersive spectroscopy. It was concluded that the trace elements in the FeSi-75 feed material (Al, Ca, Mn) were mostly responsible for accretion formation, but that rust on the low-carbon steel and oxidation of the steel contributed to accretion attachment to the lining. The total contaminant content, calcium to aluminium ratio in the FeSi-75 feed material, and thereby the liquid to solids ratio in the accretion at temperature determine the strength of attachment as well as growth of the accretion.

Feb 2, 2021

By L. Scott, M. A. Goncalves

Effective communication is a sought-after non-technical skill in the health, safety, and environmental (HSE) function and is fundamental in achieving an organization’s safety objectives. While different channels are used to communicate HSE matters, many organizations employ posters, videos, and/ or signs containing images to convey information. Communication through signage and graphical hazard symbols has been regulated in standards, but vast sections of HSE communication are bespoke communications and exist outside the sphere of standards. Effective HSE communication through images requires an understanding of the organizational culture in which the images will be used, as well as an understanding of the semiotics of the images themselves. Creative interpretation within HSE communication can create situations where the message that was received is not the message that was intended, leading to confusion and misinterpretation. This paper is aimed at elucidating the semiotics of South African HSE visual content. It was found that the indexical mode of images was most preferred in visual communication, and text-only designs the least preferred. Senders and receivers of messages differ in their opinions on the complexity of HSE communication.

Feb 2, 2021

By Margreth Tadie, Chalwe Chibwe

Physicochemical properties of copper electrolytes are a strong fundamental consideration in electrodeposition processes during electro-purification and recovery of copper. Their influence extends to mass transfer as well as energy consumption during the electrodeposition process. In this study, the influence of electrolyte composition on electrolyte physicochemical properties was investigated to review the existing literature data. This review of data is considered necessary as more and more electrowinning models are being developed for process prediction and optimisation and a need of such data is required for accurate prediction of physicochemical properties. The major components of importance to the formation of smooth high-quality and high-purity copper cathodes at optimum current efficiency are considered the species in solution. These include Cu ions, Fe ions (major impurity), H2SO4, and a smoothing agent additive. A 5-factor, 2- and 3-level experimental design was employed to determine the effect of copper (35 and 45 g/l), sulphuric acid (160 and 180 g/l), iron (1, 3, and 6 g/l), polyacrylamide additive (2, 5, and 10 mg/ l), and temperature (45 and 55 °C) on electrolyte density, conductivity, and the diffusion coefficient in synthetic copper electrowinning electrolytes. The major species in a copper electrowinning electrolyte are found to be the most relevant for prediction of physicochemical properties. These results indicate that relatively simple empirical models are sufficient for modelling of the electrolyte domain in electrowinning, without the need for the generation of vast amounts of complex experimental data.

Feb 1, 2021

By CAIJUN CHEN, MING ZHANG, ZHENWEI WU, FENG ZHOU, BOQUAN LI, XILIANG ZHANG, ZHOU PU

Traveling grate is a widely used process for iron ore pellet production; however, the thermal state of pellets in drying section is still unclear. In this study, the temperature distribution of drying section was investigated using computational fluid dynamics (CFD). Based on the calculated results of airflow velocity, space temperature distribution, and the temperature change of pellets, it concluded that there is a coupling effect in drying section in traveling grate. The gas with higher temperature in DDD transfers heat to UDD through the gap of the insulation board, and the temperature gradient of the pellet bed changed before reaching the insulation board. The characteristics of pellet bed expected to appear in DDD was displayed in UDD in advance. Moreover, a contrast experiment was conducted to verify the model.

Feb 1, 2021

By Cengiz Karagüzel, Ömer Canıeren

The mobility of gold and silver metals from refractory ores is very low due to free metal ions in their bodies that bind the transportable and free metal molecules or they are encapsulated in minerals such as sulfides, arsenosulfides, carbonaceous, and clayey materials which make it difficult to extract them. As known from the literature, the enrichment of oxide refractory gold, silver ores, Ag, and Au-rich flotation concentrated from sulfur refractory ores can be leached in the chloride-hypochlorite solutions. In this work, the leaching approach was studied to extract silver ions from refractory ores in the presence of hypochlorite media under high pressure. The mineralogical and scanning electron microscopy analysis of the sample indicated that the silver was encapsulated in barite and quartz minerals in fine sizes. In order to obtain the optimum leaching conditions for the silver ore, the effects of several parameters, namely, temperature, leaching time, NaCl and NaOCl concentration, solid ratio, and particle size on the leaching recovery were investigated in detail. The leaching experiments showed that the highest silver recovery of 62.35% was obtained under the following conditions: temperature of 150 °C, oxygen pressure of 1800 kPa, leaching time of 2 h, concentrations of 2 mol/dm3 and 0.4 mol/dm3 for NaCl and NaOCl, respectively, the solid ratio of 30%, and particle size (d80) 15 μm. The results obtained from this study indicated that the enrichment of refractory silver ores to extract the silver encapsulated in barite and quartz minerals could be possible in the chlorite-hypochlorite under high pressure, a relatively shorter leaching time compared to conventional cyanide leaching.

Jan 28, 2021

By LUIS ALBERTO TORRES-CRUZ

The assessment of liquefaction vulnerability is crucial to understanding the potential consequences of a tailings dam failure. The “Plewes method” is a relatively well-known and simple screening method to assess liquefaction potential based on results of cone penetration testing (CPT) which may be complemented with laboratory testing. The objective of the current work is to emphasise the screening nature of the method and its uncertainties when applied in tailings deposits. Specifically, the paper highlights the difficulties in assessing the intrinsic uncertainty of the method and the additional uncertainty that results from variations of the slope of the critical state line (λ10) along the depth of the CPT sounding. The results of the method are too uncertain for detailed characterisation of tailings even when a relatively low intrinsic uncertainty is assumed. However, the method characterises weaker soils with lower uncertainty (although still too high for detailed characterisation) than stronger soils. The uncertainty of the method is negatively affected by the relatively low λ10 values that are typical of nonplastic tailings. It is suggested that the results of the method should be presented in scatter plots in which the spread of the data is consistent with the uncertainty of the method.

Jan 28, 2021

By Yongjun Peng, Yufan Mu

Pyrite depression in the flotation of copper ores is difficult due to the activation of Cu2+ ions on pyrite surface. In this study, the radical chain reaction involving the redox cycling of Cu(I/II) induced by sodium metabisulphite (MBS) was exploited to selectively depress the flotation of copper-activated pyrite at pH 8.0. Electrochemical measurements revealed that the presence of Cu2+ and O2 was essential to the formation of SO•− 5 through sulphite oxidation, the main entity to convert the activating species Cu(I)S on pyrite to Cu(II)-hydroxide/sulphate, causing deactivation of pyrite. The depression role ofMBS on pyrite flotation was closely associated with the type of grinding media which affected the electrochemical conditions of flotation. When forged steel was used as the grinding media, a high dosage of MBS was required to depress pyrite, but a low dosage of MBS could almost completely depressed pyrite when high chrome steel grinding media was used. This is because high chrome steel produced a stronger oxidation condition with a higher amount of Cu2+ and O2 which promoted the formation of SO•− 5

Jan 26, 2021

By Harald Ulrik Sverdrup, Anna Hulda Olafsdottir

The long-term supply of nickel to society was assessed with theWORLD7 model for the global nickel cycle, using new estimates of nickel reserves and resources, indicating that the best estimate of the ultimately recoverable resources for nickel is in the range of 650–720 million ton. This is significantly larger than earlier estimates. The extractable amounts were stratified by extraction cost and ore grade in the model, making them extractable only after price increases and cost reductions. The model simulated extraction, supply, ore grades, and market prices. The assessment predicts future scarcity and supply problems after 2100 for nickel. The model reconstructs observed extraction, supply and market prices for the period 1850–2020, and is used to simulate development for the period 2020–2200. The quality of nickel ore has decreased significantly from 1850 to 2020 and will continue to do so in the future according to the simulated predictions from the WORLD7 model. For nickel, extraction rates are suggested to reach their maximum value in 2050, and that most primary nickel resources will have been exhausted by 2130. After 2100, the supply per capita for nickel will decline towards exhaustion if business-as-usual is continuing. This will be manifested as reduced supply and increased prices. The peak year can be delayed by a maximum of 100 years if recycling rates are improved significantly and long before scarcity is visible.

Jan 26, 2021

By Weiguo Xie, MARK LAPUTKA

The pyrometallurgical industry plays a vital role in producing metals for our modern life. With growing demand of metals and declining grade of mineable ore, innovations become critical for many mining companies. It is necessary to conduct a review of recent improvements to the pyrometallurgical industry on analytical measurement techniques, process and equipment improvements, and computer-based modeling/simulations. Many of those innovations tend to be applied to wider metals, and not be restricted by a specific metal. Therefore, we tried to cover the wide applications of many improvements to wider range of metals to reflect this trend. The challenge of a lack of robust measurement techniques under high-temperature conditions within a furnace hinders optimization of a pyrometallurgical process. Some future opportunities in the pyrometallurgical industry on analytical measurement techniques, computer modeling, and processes and equipment have also been outlined and discussed.

Jan 26, 2021

By Yi Luo, Jian Yang

Subsurface strata movements and deformations associated with longwall mining operations in underground coal mines could cause various disturbances to subsurface mine structures, ground water bodies, and coalbed methane reservoirs. In order to assess those disturbances correctly and to design effective and efficient mitigation measures, it is necessary to develop an accurate prediction model for subsurface strata movements and deformations. Decades of research have demonstrated that variations of stratification and lithology in the overburden have significant influence on the subsurface strata movements and deformations during ground subsidence process. The key strata theory states that the thick and hard key strata serve as the backbone of the overburden and control the movements of the thin and soft weak strata located above them. From an engineering standpoint, the overburden strata are subdivided into several individual groups by the key strata with each group consisting of a key layer at the bottom and weak layers overlying it. A new subsurface subsidence prediction model considering the key strata effects on subsurface strata movements and deformations has been proposed. In this method, elastic modulus, specific weight, tensile strength, and uniaxial compressive strength (UCS) of each layer are used to identify the key layers and to determine the needed subsurface subsidence parameters. The influence function method, proven to be accurate and versatile for surface subsidence prediction, was employed to predict the subsidence on each of the overburden layers from mining horizon progressively upward to ground surface with the assumption that the predicted subsidence on a given layer serves as the subsidence source for the layer immediately above. The enhanced subsurface subsidence prediction model has been demonstrated with an actual case to show its applicability and improvement.

Jan 25, 2021

By PETER ROBINSON, KEVIN BARBER, OLIVER WHATNALL

Investigation and uptake of filtered tailings continues to grow throughout the globe. This is driven by a wide range of site-specific considerations, which include such factors as tailings characteristics (e.g., amenability to filtration), production rates, climate, water availability, cost drivers, environmental requirements, and social factors. Despite the aforementioned technological growth, the currently available filtration technology is not able to meet the needs of many operations and projects that would otherwise adopt the technology. Experience with large-scale industrial filtration shows that vacuum belt filter systems meet the needs of many modern users, exceptions being the inability to effectively dewater tailings at altitude and/or with a fine particle size distribution: a potential fatal flaw. This paper presents a case study on the utilization of the patented Viper Filtration technology on gold tailings to overcome this challenge and shares the resultant full-scale plant design, highlighting the features designed to overcome cost and scalability deterrents. This technology is a novel mechanical process which complements the vacuum pressure in dewatering the filter cake as it travels along the belt filter. This project commenced with a pilot testing program, which successfully met the objective to rigorously test, measure and record any performance improvements achieved when engaging the Viper technology. Of the two tailings products tested, gross improvements of 4.2%w/w and 5.7%w/w were achieved when compared to the conventional vacuum belt filter operation. This pilot testing facilitated measurement of operating and design data, which forms the basis of the full-scale system design and resultant equipment supply of three vibration roller assemblies for retro-fitting on the existing vacuum belt filter.

Jan 25, 2021

By YUSONG MIAO, DI WU, XIANRONG YAN, YIPING ZHANG, JIE LIN, KEBIN LI

Rock fragmentation size distribution is often used as an important index to account for the blasting effect because it directly affects the subsequent loading, transportation, and secondary crushing. Due to the mismatching of explosive and rock wave impedance, high boulder yield often occurs which affects the blasting effect. In this study, methods of measuring rock acoustic impedance, rock strength point loading, and detonation wave velocity have been used to obtain more accurate input parameters. Then, in the watershed image segmentation technique, the Gates-Gaudin-Schuhmann and Rosin-Rammler distribution functions have been used to analyze and quantitatively describe the rock fragmentation size distribution in the existing muck-pile. Finally, taking the rock properties, explosive performance, blasting parameters, and system characteristic variable into consideration, support vector machine (SVM) regression model has been analyzed on the learning and prediction of samples. The results show that SVM has a good prediction accuracy, high precision, and strong generalization ability. The optimized matching coefficient of rock and explosive wave impedance K ranges from 2.50 to 2.58 times. This study has developed a series of simple, accurate methods for rock properties analysis, detonation wave velocity measurement, and muck-pile model image processing, and a basis for predicting and evaluating rock fragmentation size distribution and optimizing the matching coefficient before carrying out a blasting operation.

Jan 22, 2021

By S. K. Samal, B. Mishra, M. K. Mohanty, S. C. Mishra

Steelmaking industries consume the majority of chromium and manganese ferroalloys to impart several properties in steel and also for other purposes. The quality of ore governs the process kinetics as well as the process economy of the ferroalloy industry. The present study demonstrates the thermal transformation behavior of chromite and manganese ores with varying compositions. Simultaneous thermal analysis (DTA/TG) is employed for such ore samples where the transformation of mineral phases is correlated with the thermogram characteristics and quantified. Phase, microstructure, and compositional analysis results of individual ores corroborated with thermal analysis are in good agreement. Chromite samples are ferruginous with goethite and gibbsite contents, whereas manganese ores vary in composition and also exhibit multiple and/or overlapping transformations.

Jan 21, 2021

By Brenton Fletcher, Yongjun Peng, Wonder Chimonyo

As a cheap, renewable and non-toxic material, starch can contribute to the sustainability of the flotation process, albeit in a minor way as one type of reagent in systems involving materials with far greater impact. But the physical and chemical versatility of starch can help address another issue, namely, that of processing complex ores with decreasing grades of valuable minerals and increasing mixtures of gangue. This paper compares the results of two lab scale flotation studies where starches (native wheat starch (NWS), dextrin and two oxidised wheat starches) were used to depress two common gangue minerals, copper-activated pyrite and carbon (graphite), over a range of dosages. The oxidised starch with the larger molecular weight structures depressed copper-activated pyrite best, and the oxidised starch with lower molecular weight structures was better at depressing graphite. In both cases, the oxidised starches allowed greater recovery of chalcopyrite, pointing to selectivity potential. The extent to which the carbonyl and carboxyl moieties of the oxidised starches contribute to depressant performance is difficult to quantify, but it should not be discounted. Importantly, the results demonstrate relatively simple modifications of native starch by oxidation can yield structures suitable for depressing gangue minerals with diverse surface properties. The challenge remaining for greater application of modified starch depressants is being able to replicate the desired structures at scale in cold-water-soluble form.

Jan 18, 2021

By Viktor Lishchuk, Olof Martinsson, Tobias E. Bauer, Elena Haller

Freely accessible and non-confidential real-life geological data sets from mineral deposits are desirable for the wide range of applications in research and education. However, publicly available statistical data are limited in their number and quality—they contain reduced information about geological, geophysical, geotechnical, chemical, mineralogical, and other relevant properties of deposits. This makes such data insufficient for scientific purposes. However, the amount of geological knowledge obtained for a variety of deposits in the past allows the construction of an idealized synthetic ore body model using analytical approach. Such a model could be used for education purposes and testing basic scientific theories, e.g., visualization of deposit structure; teaching sampling strategies; testing new algorithms for mine planning; or comparing geostatistical modeling methods. This paper presents an analytical approach to simulate volcanic massive sulfide (VMS) deposits and shows how synthetic deposit model can be constructed and further used for studying sampling with drilling and simulating folding and faulting.

Jan 14, 2021