Search Documents

By Brandon R. Ball

An investigation of the effects of ozone and ozone-induced hydroxyl radical on reducing whole effluent toxicity is described and discussed relative to the application of ozone for industrial water treatment. Results from operation of an ozone system treating industrial effluent from a lead and zinc mine in Colorado are presented. The mine discharges 1,000 gpm of wastewater into a tributary of the Arkansas River and has historically exceeded Whole Effluent Toxicity (WET) limits and on occasion has exceeded numeric limits for copper, ammonia, and cyanide. Based on results of a Toxicity Identification Evaluation (TIE) conducted on the effluent and individual process waste streams, the source of effluent toxicity is believed to be primarily associated with organic reagents used in the milling process. Based on test results, an applied ozone to COD ratio of 3: 1 by weight and a contact time of 30 minutes was found to be effective for reducing whole effluent toxicity at pH 11 but not at pH 7, indicating oxidation by hydroxyl radical to be the dominant mechanism responsible for toxic-ity reduction. At an applied ozone to COD ratio of 3:1 and a pH of 11, toxicity was improved from 0 percent survival to 100 percent survival for Ceriodaphnia dubia and fathead minnow (Pimephales promelas) based

Jan 1, 1996

By Yanhui Sun, Yanan Zeng, Kaike Cai

"Hot ductility of Nb-V-containing steel has been studied by theoretical calculation and thermal simulation experiment. Meanwhile, microsegregation and precipitates were analyzed. The results showed that segregation degree of elements S, P, 0 is greater in mushy zone, while, the hot ductility was deteriorated by inclusions of Fe(S,O), (Fe,Mn,Si,Al)(S,O) in the interdendritic region. At the temperature 1100°C, a few NbN particles, 60-70nm, have little effect on mechanical property. In the temperature range 1000°C to 975°C, R.A declined rapidly from 82.36% to 69.61% with the diameters decreasing from 20 to 10nm and quantity of particles increased 23 to 45inds/µm2, respectively. In the temperature range from 900°C to 850°C, R.A reduced unobviously from 34.27 % to 30.01 % with ferric films thickening gradually. The critical stress, 52.38MPa, was equal to tensile strength at 975°C. Intergranular fracture was easy to occur with higher critical stress below 975° C.IntroductionProductivity and product quality of slab are seriously affected by cracks during continuous casting and the influencing factors of cracks are various[l]. From microcosmic angle, resisting deformation ability of initial solidification shell decreases obviously with solute elements segregation which can urge the low melting point ofliquid film to form at grain boundaries[2, 3]. Meanwhile, with temperature decreasing, particles would precipitate as the practical solubility product is greater than equilibrium solubility product. The carbonitrides would lead to stress concentration at austenite grain boundaries. Therefore, the transverse cracks of microalloyed steel would form during the straightening operation in the continuous casting process. The hot ductility of steels in the temperature of mushy zone was characterized by microalloy elements segregation, zero strength temperature (ZST) and zero ductility temperature (ZDT). The nature, shape, and size of precipitates have been investigated by TEM (JEM2100). Hot tensile test with low strain rate was simulated by Gleeble-1500. The objective of present study is to provide reference for zero defect of microalloyed steel during continuous casting process."

Jan 1, 2013

By Takayuki Watanabe, Yoshiki Shimizu, Yusuke Moriyoshi

"B-C-N nanotubes prepared by a flush evaporation method using a de arc plasma were mainly characterized by transmission electron microscopy (TEM) and electron energy· loss spectroscopy (EELS). The nanotubes obtained· were divided into three types such as carbon boron nitride and carbon or carbon nanotubes surrounded with boron nitride nanotubes. These types of nanotubes were obtained at higher temperatures than about 3000 K, however, these were not formed at lower temperatures than about 3000K. On the other hand, 11anocapsules were· formed at all the experimental temperatures and nanocapsules with a homogeneous phase were obtained at lower temperatures than about 3000 K. The effect of additives on the formation of B-C-N nanotubes was not clear. Based on these experimental data depending on temperatures and corresponding microstructures, the formation mechanisms of both nanotubes and nanocapsules were briefly .discussed 1 Introduction As reported previously, nano tubes have unique electrical properties1, 3) The preparations of nallotupes have been usually carried out by flush evaporation methods using either a de arc plasma or a laser4 -5) By these methods the reaction rate is so rarid that we have no data of intermediate products between initial raw materials and. final products of nanotubes 6-9). So, the formation mechanisms of nanotubes have been mainly speculated only from the microstructures of resultant nanoiubes. In order to have more reliable formation mechanisms, it is particularly important to have the information of intermediate products at the corresponding temperatures. From the viewpoints, we have studied about the effects of temperatures on the preparation of nanolubes. Here we report mi firstly some problems on the preparation of B-C-N nanotubes 10), secondly the effects of temperatures on the preparation of B-C-N nanotubes, and finally the formation mechanisms of nanotubes."

Jan 1, 2000

By James L. Whitlock

Biological treatment of mining and industrial effluents reached full scale commercialization around 1980. These proven, low cost, technologies have been limited in application due to a number of factors, including extended periods of time and cost required for pilot testing as compared to chemical treatment technologies, lack of biological expertise in metallurgical personnel, longer treatment periods in some cases, and performance failures based on improper application. Renewed interest in biological treatment technologies is being driven by permits with lower effluent concentration criteria, permits with bioassay evaluation, the need to remove thiocyanate, nitrates, sulfates and? other parameters. Chemical treatment processes, in general, have not been able to meet these present requirements, or require elaborate? combinations of processes, in terms of effluent quality and treatment economics. This paper addresses biologieal treatment of mining and industrial waste waters and selected recent advances in these technologies. The future looks very bright for application of these low capital and operating cost technologies,

Jan 1, 1998

By R. E. Aune

In the present work, a critical assessment of the thermodynamic information available for the ternary system Ni-W-0 has been carried out; This was complemented by experimental measurements of the standard Gibbs energy of formation of the ternary compound NiWO, by solid state galvanic studies involving Zr02-CaO solid electrolyte. The assessed thermodynamic data, together with the phase diagram information available in literature, were employed to generate the ternary phase diagram for the system Ni-W-0 in the temperature range 1073-1273 K. The calculation of the phase diagram was carried out by computer optimization according to the "CALPHAD" method. The computed phase diagram has been confirmed at isothermal sections by identification of the phases present in samples equilibrated at defined temperatures.

Jan 1, 1994

By Harrison Hodge

In the Bayer process for alumina production, between 2–35% Al2O3 is lost with bauxite residue due primarily to incomplete dissolution of aluminiumbearing minerals during caustic leaching or the precipitation of sodium alumino-silicate solids. The recovery of sodium and aluminium from the residue, and particularly from the contained sodium alumino-silicates, is becoming an increasingly critical issue from both an environmental and economic standpoint. Lime-soda residue sintering followed by selective leaching has been proposed as a method to recover sodium and alumina. The factors influencing the sintering mechanisms and kinetics, and the subsequent leaching have not been well described to date. In this study, the physical and chemical changes taking place during isothermal sintering of bauxite residue in air, particularly at short reaction times are investigated using scanning electron microscope (SEM) and X-ray diffraction (XRD). The impacts of these changes on the recovery of valuable materials are reported.

By Berger. P.

The accepted definition of the function of an edge protector fails to specify adequately the several tasks which it must perform to be functionally effective: detailed analysis of these tasks leads to the reasoned conclusion that they cannot satisfactorily be fulfilled by the conventional types of "edge-strips". The true cost of edge protector failure is cumulative: renewal costs are dwarfed by the increased operating expenses and production losses which result from but partial or incipient failure of the edge-strip; yet, the several supposedly improved types, for use with starter-blanks, generally were "built down to a price", prolonging the agony, as it were. Clearly, a fresh appraisal of the problem was overdue, and more especially so with the advent of "permanent" cathodes. As a result, new methods of edge .protection have been developed, including the so-called "EDGEWISE" system in which the present author as patentee *) has a vested interest-which he hereby declares. Due mention is made of recent progress in protecting the edges of aluminium "Jumbo" cathodes in zinc electrowinning operations, although the present Paper is more concerned with edge protection of starter-blanks and permanent cathodes in copper ER/EW processes, where most of the "old" problems now may justifiably be claimed to have been overcome, Mention is also made - albeit at this time necessarily only briefly, and confined to edge protection - of "rigidized" metal blanks and permanent cathodes: a most recent development**) which may prove to represent a "breakthrough": time will tell.

Jan 1, 1987

By M. T. Ernett

Significant amounts of arsenic are often present in effluents arising from the mining of sulfide ores for the extraction of metals such as copper, gold, lead and zinc. The arsenic is usually removed from the process effluent by co-precipitation with iron because of its common occurence in the mined ore bodies and the excellent adsorptive property of the precipitated hydrous ferric oxide compound. There has been controversy, however, over the long-term stability of the arsenic-bearing ferrihydrite which is produced. This paper presents the results of laboratory studies which indicate that the cations of calcium, magnesium, zinc, cadmium and lead, increase the pH range of effective arsenic adsorption in the Fe-As precipitate from 4-7 to 4-9. The increase in the pH range is similar for all of the added cations investigated. Sulphate ions are shown to have a minimal effect on the residual dissolved arsenate concentration. Silicate ions reduce the adsorptive capacity of ferrihydrite if they are present before the arsenic is adsorbed.

Jan 1, 1994

By Patrick Clark

As part of the Mine Waste Technology Program (MWTP), a large-scale column test using bacteria and a sulfide ore was conducted at McClelland Laboratories, Inc., in Sparks, Nevada. Four technology providers participated in this demonstration. A mining company in Nevada provided the sulfide ore, process effluent and make-up water. A process effluent column, a chemical oxidation column, and the four biological treatment columns were set side by side on a test pad outside the laboratory building. The process effluent and chemical oxidation columns were used for experimental control. The goal of this project was to evaluate the viability and feasibility of using these biodegradation technologies to reduce the cyanide to the regulatory level of 0.2 parts per million (ppm) within an acceptable timeframe and with low operational costs. The column testing began on December 3, 1998 and operated until May 17, 1999. One technology provider reached the regulatory level within the 158 days. The remaining three biotechnology columns were approaching the regulatory limit at completion of the demonstration. The MWTP is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered through an interagency agreement with the U.S. Department of Energy (DOE).

Jan 1, 1998

By David G. C. Robertson

A new approach is described for the calculation of the kinetics of metal/slag, metal/slag/gas, and metal/matte/slag/gas reactions. The algorithm assumes that equilibrium is achieved at the interface between phases, and uses an equilibrium solver (such as SOLGASMIX) to compute the equilibrium state at the interface at each time step during the reaction. For multiple phase systems a number of unit operations, representing the different phases and interfaces, must be connected together in a reasonalbly complex manner, and the METSIM software package has been utilized for this purpose. The new approach is superior to the SMAK software developed by the author and his co-workers over the past decade, for the reasons discussed in this paper.

Jan 1, 1995

By Brian G. Thomas

Quality problems in continuous casting of steel can be identified as they occur by monitoring mold signals (level sensor, thermocouples in the mold walls, friction etc.) and taking appropriate action (such as slowing casting speed, changing taper, changing a clogged nozzle, or later visual inspection of the surface for possible downgrading. Surface depressions and groups of deep oscillation marks form at meniscus and reduce local heat transfer as they move down the mold at the casting speed. This slows shell growth, increases shell surface temperature, and causes characteristic dips in mold thermocouple signals. More importantly, they are also associated with longitudinal cracks. Characteristic thermocouple signatures have been identified for many defects, including sticker breakouts, transverse depressions and deep oscillation marks, narrow-face bleeds, transverse comer cracks, longitudinal cracks, mold level fluctuation defects, and other problems. With the help of computational models, these mold signals should be used to troubleshoot defects, and to take appropriate corrective action. Keywords: Continuous casting, defect detection, thermocouple signals, on-line control

Jan 1, 2003

By Cody Burcher-Jones

The recovery of rare earth elements (REEs) through heap leach/in situ techniques from so-called ion adsorption clays (IACs) is attractive due to their inherent simplicity. However, the underlying mechanisms of these processes are poorly understood. In this study, the deportment of REEs in a typical IAC material has been investigated and was found to concentrate in the phyllo-layers of the clays, especially hallyosite, and was readily desorbed by various ion-exchange reagents indicating various potential routes to liberate them. Here we are reporting the use of seawater (0.5 M NaCl), spiked with various amounts of (NH4)2SO4, and found better extraction using a reagent mixture than NaCl on its own. Further, the leaching of REEs from a bed of clay material was investigated over time to understand the rate of transport through the stagnant material. Results indicate that REE release is likely to be controlled by diffusion through the clay material, while desorption in agitated systems is rapid. A degree of fractionation between different REEs can be observed during diffusion. Nonetheless, the successful operation of in situ leach operations for this type of material would depend primarily on how easily solution cocktails can be made to flow through the bed material.

By Brian Lightfoot

Ausmelt technology is a versatile bath smelting technology with application in many waste treatment fields at low capital and operating cost. Heavy metals extracted from wastes may be recycled to mainstream use and the slags produced will be inert and suitable for use as aggregate, shotblasting grit or other applications.

Jan 1, 1994

By Dale A. Zuck

Recovery of aluminum metal from drosses? is a major factor in the recyclability success story enjoyed by the United States aluminum industry. Today's modern dross processor uses the latest technology to maximize metal recovery at the lowest cost while complying with all environmental laws and regulations. Most dross processors, however, pay little attention to the resulting saltcake, the end residual of dross recyCling, and rely on landfills for .disposition of this material.. The alternative is to recycle the saltcake, but the success of this technology is dependent on the development of reliable outlets for each of the saltcake constituents. This paper discusses the evolution of an aluminum dross oxide processing technology that ,produces an economically attractive source of alumina for the production of portland cement.

Jan 1, 1995

By Michael J. Nicol

This paper summarizes some of the results of a study of the reactions involved in the Caron leaching process and identifies the roles of the major dissolved species in the kinetics of dissolution of iron alloy particles formed during reductive roasting. Using rotating disk electrodes and synthetic leach solutions, the reduction of water with the evolution of hydrogen was found not to occur on a dissolving iron surface under typical leach conditions. It has been established that the oxidative dissolution is governed primarily by a reaction involving reduction of Co(III) to Co(II) ions. The reduction of oxygen was also found to make a significant but largely indirect contribution to the kinetics of the dissolution process. The dissolution rates of various iron-nickel-cobalt-copper alloys which simulate the dissolving alloy particles in a Caron plant were measured in synthetic leach solutions under aerobic and anaerobic conditions. The initial dissolution rates of iron, nickel and the iron alloys were found to increase in the presence of thiosulphate, whereas the thiosulphate had a negative effect on the dissolution rates of cobalt and copper. It is shown that the eventual passivation of the iron occurs sooner in solutions rich in Co(II) ions. Whilst these conditions are present in the quench slurry, on-site measurements have shown that due to the very high concentration of reduced dissolved species, passivation does not occur until the slurry is strongly aerated. In the light of these fundamental findings, options for optimizing the rate of dissolution and minimizing the extent of passivation of the iron and iron alloys are discussed. Keywords: Ammonia, leaching, alloy, kinetics, passivation.

Jan 1, 2004

By K. Gao, R. Dry

"Carbon boil, which results in excessive spitting and even complete destruction of a metal drop, could significantly influence the efficiency of direct smelting processes. Carbon boil has been studied as a function of some key parameters such as melt sulfur content, oxygen partial pressure, and melt area/volume ratio. The time of carbon boil was determined using a CCO camera coupled with a time/date generator connected in parallel to a video recorder and a computer. The time of carbon boil was in the range ~5 - 15 seconds under the conditions in this study. A mechanism for carbon boil has been proposed.IntroductionThe occurrence of carbon boil in molten iron drops can result in excessive spitting and sometimes even complete destruction of a metal drop. In direct iron smelting processes, this could significantly influence the decarburisation of liquid metal and the post combustion and hence may influence the efficiency of smelting processes. The generation and consequent ejection of metal droplets into the gas phase occurs due to the intense turbulence in the bath which results from the injection of gases and coal. The aim of this investigation is to understand the fundamentals governing the carbon boil phenomenon under direct iron smelting conditions to assist control of process efficiency.Carbon boil phenomenon has been studied as a function of some key parameters such as melt sulfur content, oxygen partial pressure and melt area/volume ratio. The time for the occurrence of carbon boil has been determined in this study at 1440 °C using a novel approach which includes utilisation of a CCD camera coupled with a time/date generator connected in parallel to a video recorder and a computer. This arrangement permits the capture of the entire sequence of events leading up to carbon boil and therefore the determination of time of boil which is in the range -5 - 15 seconds under the conditions in this study."

Jan 1, 1996

By Enrico Cerilli, Bryan Salt

Xstrata Nickel’s Sudbury Smelter has systematically developed its converting aisle from a single stage to a counter current multi stage converting process. This has required the development of two unique converters; the Slag Cleaning Vessel (SCV) and the Slag Make Converter (SMC). This has resulted in a unique three stage converting process that enables treatment of secondary materials and producing a slag that can be discharged without further treatment. The paper will also discuss future changes currently being considered to further improve environmental, plant hygiene and productivity performance.

Jan 1, 2009

By H. Sieber

Multilayer samples of tantalum and aluminum with the composition of Al-25Ta were prepared by cold rolling of elemental foils. The microstructure and phases were characterized by XRD, SEM and TEMISAED and the reactive phase formation was examined by DSC and DTA measurements in multilayer foils rolled for different deformation levels. The rolling procedure yields a decrease of the Ta particle size in the Al matrix and also results in the formation of a multilayer structure with a thickness of the elemental foils down to 200 nm in average. No phase formation is observed during the cold rolling procedure. While XRD and DSC measurements show no phase formation up to the melting of aluminum for samples rolled up to 40 F&R (fold and rolling) passes, in samples rolled for 50 or more F&R passes a first phase formation reaction yield an interfacial layer of TaAl3. Contrary to former studies in the investigated cold rolled Al- 25Ta multilayers the reaction starts at temperatures as low as about 340°C. The first stages of the reaction are associated with two exothermic maxima, that increase in amplitude and shift to lower temperatures with increasing number of F&R passes. At higher temperature the TaA13 reaction layer thickens very sluggishly and yields a third exothermic maxima at about 600°C. Isothermal DSC scans show the reaction is not finished for samples containing elemental particles larger than 1 pm after annealing at 550°C for 5h. In all the investigated samples no Al- Ta phase other than Tad3 was observed to grow for heat treatments up to 800°C. Multilayer samples heated up to 1400°C show a morphology consisting of small AITa2 particles embedded in a single phase TaA13 matrix. The multilayer microstructure and reaction product morphology are characterized by SEM and TEM investigations in cross-section and plan view geometry.

Jan 1, 1998

By K. R. Robilliard

An outline is given of the problems facing tlile lead and zinc industry from the viewpoint of the range of residues currently produced from electrolytic zinc, blast furnace and other processes. Smelting approaches available using top submerged lancing technology are discussed and analysed. Pilot plant results for a range of lead and zinc-bearing materials are presented.

Jan 1, 1992

By E. Kuzeci, R. Kammel

"Lately various voltametric methods have gained increased attention as an analytic tool in hydrometallurgy. Voltammograms with mercury drop electrodes or glassy carbon electrodes provide information about the electrocrystallization of cathodic deposits and allow calculation of kinetic data by means of characteristic parameters like the peak potential and peak current and their variation with the voltage scanning rate.Cyclic voltammograms are also suitable for identification of reaction sequences. Voltammograms with carbon paste electroactive electrodes containing metal sulphide additions reveal information about the dissolution behavior. The stripping voltammetry can be applied to analyze metal ions and organic additives (e. g., thiourea) in extreme low concentration. Typical application of the various methods studied with microcomputer controlled measurement system are explained by examples selected from copper hydrometallurgy.IntroductionThe use of electroanalytical methods in metallurgical process control can be dated back to the starting period of industrial copper refining, when the deposition of the metal ions was followed electro-gravimetrically by weighing the electrode with deposits (1). The principles of metal deposition and dissolution have not changed but the methods to follow these phenomena were subjected to noticeable developments and especially the introduction of polarographic investigations by Heyrowsky (2) has greatly contributed to the progress in electro-analysis. A review about the fundamental work on the electrochemical kinetics in earlier time is compiled in a monograph of Vetter (2). With the steady improvements in the instrumental techniques, it is nowadays possible to apply several current and potential modulations for measurements with improved selectivity and sensibility. There is however, still a lack in theoretical interpretation of the data obtained. More theoretical information are already available for linear voltametric methods for systems where reduced as well as oxidized species are dissolved in the electrolyte (4, 5). Some recent investigations have also shown the reliability of these techniques to study electro-crystallization (6, 7). Main fields of the application in the hydro - and electro-metallurgy are:"

Jan 1, 1989