Search Documents

The height of permanent slopes at the Panguna mine of Bougainville Copper Limited will vary from 350 to 950 metres. A few degrees difference in slope angle has a large effect on the ore/waste stripping ratio. Optimum slopes can be achieved if longer batter slopes (exceeding 45m height) are excavated using bulldozers to trim parallel to controlling fracture surfaces. Unnecessary slope flattening by incorporating benches can cost millions of dollars in lost ore. Faults and other major weaknesses, which can result in wedge failure or erodible zones have been treated successfully with shotcrete, rockbolts and cable dowels. To minimize support effort and interference with mine production, early identification and treatment of unstable areas is important.

Jan 1, 1987

By R. Perez

The consumption of grinding media forms a significant part of the operating cost of a mineral processing plant. An estimated half billion pounds of steel in the USA and over one billion pounds in the world are consumed each year in wet grinding alone. However, there is some conjecture as to the interacting roles of abrasion and corrosion. In order to provide a more complete picture of the conjoint action of abrasion and corrosion, marked ball tests were conducted on different grinding ball compositions in a laboratory ball mill and the metal losses were measured on varying the conditions, i.e., pH, PO2, in wet grinding a Cu-Ni gabbroic rock and compared with taconite grinding. Ball wear rates ere discussed with respect to ball composition and microstructure and the varying conditions used in the grinding tests.

Jan 1, 1984

By R. D. Lopez

The concept of "heat recuperation" for the grate-kiln pelletizing system was first implemented at the Sydvaranger plant in Norway in 1974. Essentially, heat recuperation involves bringing hot air from the second stage of the pellet cooler to the drying zone to increase drying-air temperature to the maximum limit. 'Burner-fuel savings result from a lower kiln secondary-air mass flow at a higher temperature. Because of the fuel benefits achieved at Sydvaranger, heat recuperation has been included innumerous new grate-kiln plants built since then, and some older plants have been retrofitted for heat recuperation. In recent years there has been much confusion about the fuel benefits of heat recuperation. To answer some of the questions, a mathematical model was developed and plant tests were conducted at Minntac Phase 111. Minntac is a magnetite taconite concentrating and pelletizing plant, and Phase III has two indurating lines. This paper presents the results of the studies and plant tests.

Jan 1, 1980

It was shown previously that chalcopyrite could be floated without using a collector when the ore samples were treated with small amounts of sodium sulfide (Na2S). The role of this reducing agent was considered to be one of a cleaning agent to remove the hydrophilic surface oxidation products. It was later found, however, that the collectorless flotation could be obtained only under slightly oxidizing conditions. This might suggest that collectorless flotation is not due to the clean surface but to the elemental sulfur which may be present as an incipient oxidation product. Therefore, a search for the presence of elemental sulfur has been made by means of ESCA, mass spectrometry, and solvent extraction followed by W spectrophotometric analysis. On the basis of these results, the mechanisms of collectorless flotation are discussed.

Jan 1, 1983

By William L. Carter

Through your presence here this morning and your membership in the Society of Mining Engineers, you have shown that you are interested in keeping abreast of the latest technology and mining procedures, want to be part of the continuing progress made by those in your profession, and are looking for ways to participate in expanding your professional and personal experiences and skills. All of these factors are part of your continuing education, the need for peer identification or recognition, and the desire to make a specific contribution to strengthening your profession. However, you may be here with or without your company support and financial backing, unless you are self-employed. Whether you are here for the above reasons, or for many others, your presence reflects a recognition of the importance of participating in the organizational structure of your profession.

Jan 1, 1981

By V. J. Hucka

A 0.5 m (20 in) diameter high pressure natural gas pipeline crosses over a coal mine located in Central Utah. Ground movement induced by the mining operation could possibly place excessive strain on the pipeline causing it to rupture. The mining operation extracts coal from two seams using the room and pillar method. The seams are situated one on top of the other and both lie directly under the pipeline. At present, only the upper seam is being mined beneath the pipeline. However, in the future, the mining operation of the lower seam will also affect the pipeline. As would be expected, mining of both coal seams causes surface subsidence. This is especially true when the pillars are extracted during retreat.

Jan 1, 1983

A conventional paddle-type mixer and a gravity flow mixing device were evaluated for conditioning of phosphate ore with fatty acid and fuel oil, and for acid scrubbing prior to cationic flotation. Gravity flow mixing required less residence-time, but slightly higher reagent concentrations to achieve recovery levels similar to conventional conditioning. Grade was less sensitive to reagent concentration using the gravity flow mixer. For acid scrubbing, the gravity flow mixer proved equally effective. In this paper, the effect of time, pulp density, reagent concentration, and emulsification on conditioning and acid scrubbing efficiency of the two devices will be discussed.

Jan 1, 1987

By J. H. Elledge

Hydraulic Transportation of Phosphate Ore from, a 40,000 Cubic Yard per Day Strip Mine IMC is transporting 1500 yards per hour of phosphate ore in a water slurry a distance of approximately five miles from a strip mine to a flotation beneficiation plant at their Noralyn Operation. in Barrow, Florida. This ore, which consists of approximately 1/4 phosphate, 1/2 silica sand, and 1/4 clay slimes, is being pumped through a 20 inch O. D. pipeline using seven 20 and 18 inch GIW metal pumps direct connected to electric, motors. This paper details some of the problems involved and the specific methods used to accomplish this bulk material handling requirement.

Jan 1, 1966

By William E. Horst

Ore grindability data based on various techniques to measure comminution characteristics are used to evaluate the crushing and grinding efficiency in mineral processing operations. The importance of achieving improved comminution efficiency, in terms of energy consumption, has been emphasized by recent increases in the cost of electricity. From a theoretical standpoint, the objective of a grinding operation might be expressed as maximizing the production rate at a given grind size while minimizing the energy consumption per ton of material ground. To achieve this objective in an industrial operation presents a challenge especially in view of changes in the raw material which are normally encountered. Various procedures1-5 used to determine energy-size parameters and grindability measurements have been reported. The proposed relationships between particle size and energy consumed have much in common between many of the techniques for measuring grindability. Probably the most widely used parameter to measure ore grindability in recent years is the Bond work index6, Wi, which is defined as the kw-hr per ton required to break from infinite size to a product size of 80 percent passing 100 microns. If the breakage characteristics of a material remain constant over all size ranges, then the calculated work index would be expected to remain-constant since it expresses the resistance of material to breakage. However for most naturally occurring raw materials differences exist in the breakage characteristics depending on particle size, which can result in variations in the work index depending on grind size. Consequently work index values are generally obtained for some specified grind size which typifies the comminution operation being designed or evaluated.

Jan 1, 1975

By Brig M. Moudgil

It was reported earlier that francolite and dolomite from the South Florida deposits cannot be selectively floated using conventional conditioning with sodium oleate as the collector. However, dolomite could be separated from francolite if the minerals were first conditioned at pH 10 followed by reconditioning at a lower pH. An optimum separation was achieved at a reconditioning pH below 4.5. Reconditioning pH and collector concentration were determined to exert a major influence on the selectivity. Flotation, adsorption and transmission infrared spectroscopic results are presented to elucidate the mechanisms underlying the observed selectivity.

Jan 1, 1984

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., under contract to the Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1986

By C. Hosten

This paper presents the results from an extensive research program on the vacuum filtration of iron ore slurries. Experiments were conducted with the addition of several types of flocculants and surfactants. The filtration response of the slurries was studied in terms of the cake formation rate and the residual cake moisture. An analysis of the results is presented in ascertaining the role of flocculants and surfactants during filtration

Jan 1, 1983

By W. L. Staker

The Bureau of Mines investigated selective extraction of Au and Ag from a low-grade Au ore containing Hg. Gold and silver were extracted from the ore in cyanide slurries, and Hg extraction was suppressed with sodium or calcium sulfide. Maximum Au extraction and minimum Hg extraction were obtained using solutions containing 0.34 lb NaCN/ton of solution. Increasing the cyanide concentration increased Hg extraction without increasing Au extraction. Mercury extraction from the ore was suppressed with 0-5 to 2.9 Pb CaS/lb Kg in the ore. Gold-to-mercury ratios of 100:1 to 400:1 were obtained in the leach solution, and on the activated carbon in a CIP circuit.

Jan 1, 1983

By J. H. Bassarear

Conventional crushing and grinding circuits are compared to semiautogenous circuits. Recent installations of each circuit are reviewed and seven methods of using autogenous or semi- autogenous techniques are described. Steel and power consmption data are reported and benefits of a dedicated digital computer are discussed.

Jan 1, 1981

By Kenneth S. Johnson

Large reserves of high-purity Permian gypsum crop out and are at shallow depth in three regions of western Oklahoma, Gypsum beds in the Blaine Formation are 10 to 30 feet thick and are generally 95 to 99 percent pure, whereas the massive Cloud Chief Gypsum is 20 to 100 feet thick and is 92 to 97 percent pure. Reserves are estimated at 48 billion short tons. Eight companies in the State currently mine about 1 million tons of gypsum each year for wall- board, for plaster, as a retarder in portland cement, and as a soil conditioner. Future uses, under more favorable market conditions, may be in the chemical industries, largely because of gypsum's potential as a source of sulfur. Three thick sequences of Permian rock salt underlie most of western Oklahoma at depths of 30 to 3,000 feet. Individual salt beds 5 to 30 feet thick are interbedded with thinner layers of shale and anhydrite. Five large salt plains, fed by natural springs of saturated brine constitute additional resources of salt. Reserves, estimated at 20 trillion short tons, are virtually untapped, and, ironically, about 90 percent of the salt used in Oklahoma is imported. Chemical data on the rock salt are lacking, but evaporated salt produced from brines is generally 97 to 99 percent pure. Current production from three solar-evaporation plants is used mainly for stockfeed, recharging water softeners, and deicing roads. Potential uses are in the chemical industries, where salt or brine is a necessary raw material.

Jan 1, 1973

By Takashi Goto

In 1968 three historical rockbursts had occurred at Bibai Coal Mine in Hokkaido. At the time they had been observed by several seismic observatories as natural earthquakes away more than 100km from Bibai City. These facts taught us that the occuerrence of failure yielded in underground opening that was accompanied with seismic wave could be observed by seismometer on the surface. After two years from this desaster, the study concerning to microseismic events generated from underground mining panels has been begun by researchers with heart-throb.

Jan 1, 1982

By Jerry W. Owens

Current steel consumption for grinding media, mill liners and rods in North America runs in excess of 400,000 tpy in the mineral processing industries. Steel consumption ranks as one of the major consumables along with energy in most operations with total annual industry expenditures in excess of $275 million. It is generally agreed that there are 3 main categories of wear responsible for this metal loss. These three main types can be loosely defined as follows; 1) Abrasion. The cutting, rubbing, scrapping and gouging of the metal surface by the ore with which it is in contact; 2) Impact. Spalling on both micro and macro scale, breakage, and deformation due to metal to metal contact; 3) Corrosion. The oxidation losses of the metal due to electrochemical interaction between the grinding media and the slurry

Jan 1, 1984

By Joseph Cervik

The mined coal bed and surrounding strata are both sources of methane which must be control led during mining. During developmental mining, the mined coalbed is the primary methane source; during retreat longwall mining, the primary methane source is the overlying strata. Underground technology is being developed to control both sources. This technology involves drilling long horizontal drainage holes into the mined coal bed and relatively short holes (less than 152 m or 500 feet) into the overlying strata. Because of the large volumes of methane that flow from such drainage holes and the limited ventilation available for in-mine dilution, underground pipelines are used to transport the drained gas to the surface. Large- scale in-mine degasification demonstrations showed reductions in methane flow of up to 70% during developmental mining.

Jan 1, 1981

By L. A. Wasselle

The Israel Mining Industries Institute for Research and Development has developed, during recent years, a number of new processes for fertilizer materials. Their phosphoric acid processes, however, are capable of producing an acid of far higher quality than that normally associated with fertilizer grade acid. This paper will discuss two of these processes showing the quality attainable and the capital and operating costs for, U. S. conditions. The Standard IMI Process is based on the acidulation of phosphate rock with hydrochloric acid and involves solvent extraction for the separation of high quality, phosphoric acid from the resulting solution. The IMI Purification Process applies the same solvent extraction technique to the purification of a wet process phosphoric acid from sulfuric acidulated rock. IMI has built and operated a semi-works scale demonstration plant for the standard process. The first commercial plant was started up in; Japan in 1962. This small seven metric ton per day plant is currently producing a furnace quality acid. A larger 50 metric ton per day plant is nearing completion in Brazil. Another 50 metric ton per day plant is under design while a large plant with a capacity in excess of 150 metric ton per day is in the planning stage. Both of the latter facilities are for Israel.

Jan 1, 1966

By Leons Kovisars

Two-thirds of the world copper produced in 1979 incurred cash costs between $0.35 and $0.89 per lb, averaging $0.62 per lb. North American costs are higher at $0.48, $0.88, and $0.68 per lb, respectively. Variable cash costs are $0.20, $0.58, and $0.39 per lb for the world; $0.29, $0.63, and $0.46 per lb for North America. Cash costs are relevant for comparing existing operations and evaluating market pricing during periods of excess supply. Analysis of full costs of production (cash costs plus income taxes, profit, and non-cash items) becomes relevant in evaluating the incentive price required to develop new production plants. In mid-1979 this cost (incentive price) was about $1.10 per lb; it is expected to approach $2.00 per lb by 1985.

Jan 1, 1979