Search Documents

By L. J. Drew

The plate tectonic setting, regional geology, and certain aspects of the economic geology of the iron-rare-earth-nio-bium ore bodies at Bayan Obo, Inner Mongolia, China, were studied by a team of geologists from the Tianjin Geologic Research Academy and the U.s. Geological Survey between 1987 and 1989. These ore bodies were formed by hydrothermal replacement of Middle Proterozoic dolomite in an intracontinental rift setting. A variety of veins and/or dikes that have a carbonatite-like mineralogy cut the footwall clastic rocks and migmatites. A stockwork of veins occurs at several locations in the footwall. The hanging wall is a shale that has been converted to a K-metasomatite and has microcrystalline potassium feldspar as its principal constituent. This shale served as a sealing caprock that contained the chemical solutions that reacted with the dolomite and that created the enormous concentration of mineralized rock in an 18-kilometer-long syncline. The rocks that host these ore bodies and the associated mineralized areas occur today as roof pendants in granitoid rocks of Pennian age that were emplaced during a continent-to-continent collision during that period.

Jan 1, 1991

By G. J. Joy, J. P. Rider

"Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 100 ft./min. This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the National Institute for Occupational Safety and Health [NIOSH] is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research [OMSHR] Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities (500, 700, and 900 fpm) and at water pressures of 100, 150, and 200 psi. Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer a spray manifold was fabricated and evaluated at an underground operation. INTRODUCTION In 2012, underground coal mining in the United States produced a total of 342 million short tons, with longwall mining accounting for over 53% of this production [EIA 2013]. The longwall mining industry continues to see remarkable and significant improvements in longwall mining equipment and mining practices. Average shift production during compliance dust sampling has increased from 3,500 tons per shift in 1994 to approximately 6,000 tons per shift in 2012. A dramatic decrease in working longwall faces from 80 to 49 has occurred over the same period [Fiscor 2013]. Factors specific to longwall mines that supported productivity improvement include: higher capacity shearers, improved shield hydraulics and control, higher horsepower for equipment, wider face conveyors, and larger faces. Today, the average face width has increased to 1,188 ft., with one longwall operation reporting a face width of 1,650 ft. compared to an average of 750 ft. in 1994 [Fiscor 2009, 2014]. Panel lengths in 2013 averaged 11,307 ft. compared to 7,000 ft. in 1994. Overall production from U.S. longwalls has increased by nearly four percent from 2007 to 2012 with over 182 million tons mined annually [EIA 2013]. Given the volume and rate of coal produced on longwall faces, the potential to generate large quantities of respirable coal mine dust also exists."

Jan 1, 2015

By J. Richard Lucas

Today, the future of the coal industry is extremely bright because coal can be produced at a cost which makes it competitive with other energy sources. However, the industry has been forewarned that further cost reductions must be made if it expects to remain a serious contender in the growing energy market. Surface as well as underground operations must be improved. The very same elements which affected production a. few years ago still exist today and will continue to be present in the future. Improvement's in production mining equipment, mining methods, and auxiliary equipment have resulted in reduced costs over the past few years. Efforts must be continued toward further reducing costs in areas which have been improved previously, and new areas should be investigated for possible improvements. Therefore, new techniques must be developed which will enable the industry to augment its current efforts in reducing the cost of mining. The logical place to begin evaluating the factors affecting production and cost is in the immediate face area where a substantial part of the total cost of mining is incurred. The coal industry stands to gain much through the development of new techniques for analyzing the numerous variables affecting production and by establishing methods for eliminating or minimizing the adverse effect of those variables which can be controlled. Intuition and trial-and-error methods have been the standard means used to resolve many of the factors which influence production. As a result, many elements are overlooked or ignored because their effect on production is not pronounced and cannot be readily resolved. The need for a method of analyzing such factors was recognized by the Office of Coal Research. Therefore, in April 1962, under OCR sponsorship, a. research project was initiated at Virginia Polytechnic Institute (VPI). The objective of the project was to identify the factors which influence mining costs in the immediate production area, and to develop methods and techniques which will enable the coal operator to minimize production costs. The objective of the research at VPI has been successful, and techniques have been developed for establishing quantitative facts concerning the interrelationships of production activities.

Jan 1, 1965

By Jack V. Hill

A unique type of grinding mill liner has been developed by Waagner-Biro A.G. of Austria. This liner system, termed an angular spiral lining (.ESL), was, successfully tested by Magma Copper Company's San Manuel concentrator in both their 10 Ft x 10 Ft (3.05m x 3.05m) and 12 Ft, 6 In x 14 Ft (3.81m x 4.27m) grate discharge wet grinding ball mills. Magma Copper's savings in power and grinding balls justified conversion of more than half of their twenty-six ball mills to the ESL system.1,2 The ASL system was provided by the Capitol Castings Division of Midland Ross Corporation, the exclusive licensee for such conversions. Capitol Castings proposed the following as expected benefits from installation of an ASL system in an 18 Ft x 21 Ft (5.49m x 6.40m) overflow discharge wet grinding ball mill at the Pinto Valley Operation of Cities Service Company: "(a) Reduction of power consumption per ton of ore milled = 12%, (b) Increased throughput = 6%, (c) Reduction of ball consumption = 6%."

Jan 1, 1982

By P. A. Rittenhouse

Reserves of potash are more than adequate to meet future world demand for this primary fertilizer nutrient. The bulk of both reserves and current production is located in only a few countries. Recent attention has focused on potential development of smaller reserves to supply local markets in developing areas of the world. However, most new capacity in the next decade will be built in countries with large current production and reserves. The paper reviews current and future projects that will add to the world supply of potash.

Jan 1, 1985

By Ronald W. Marrs

Kimberlite contains a unique assemblage of minerals and exhibits a characteristic pattern of spectral reflectance in the visible and near-infrared wavelength region. This spectral pattern is readily discerned in well-exposed kimberlite outcrops, but becomes increasingly difficult to identify when outcrops are partially covered by vegetation or soils derived from non-kiaberlitic materials. Detection of poorly exposed kimberlite diatremes is possible using multispectral imaging techniques in which spectral bands are chosen to optimize contrast between he kimberlitic soils, non-kimberlitic soils and vegetation. Careful processing of the multi-spectral data is also essential in order to separate the spectral signature of kimberlite from the signatures of other components of the scene.

Jan 1, 1984

By Susanne Pignolet

Ore microscopy has been applied to the complex lead-zinc-copper-cobalt-nickel ores from the Madison Mire in the Fredericktown subdistrict of the Southeast Missouri Lead District to predict potential beneficiation problems. It has been found that in some portions of the ore deposits, textures are present which may result in metal losses. In ores from the Bonneterre Transition Zone the intimate association of siegenite with chalcopyrite may result in cobalt and nickel losses to the copper concentrate. In ores from higher stratigraphic horizons, this association is relatively uncommon, and siegenite is commonly associated with bravoite. This latter association will increase the recovery of the cobalt and nickel in bravoite, even though some of the fine-grained bravoite will not be recoverable. Other textures which may result in potential beneficiation problems include coatings of covellite on chalcopyrite and inclusions of sphalerite in galena.

Jan 1, 1983

By D. N. Hillhouse

The economics of exploration target selection can be measured ultimately only against a company's success at developing mines. In the following brief history of the mine acquisitions of one company, Placer Development Limited, I try to identify the principal targeting parameters and the principal skills that came into play for each property and examine how these have changed with time. The process of target selection in exploration is directed: - first by corporate investment criteria which define objectives and acceptable levels of risk for pursuit of those objectives; - second by experience and skills which permit us to minimize risk; and - third by anticipation of future events relating to ore discoveries and changes in external risk factors.

Jan 1, 1984

By Ernest Hucke

This paper will cover basic pneumatic and electronic sensors, transducers, transmitters and their application in the Mining Industry.

Jan 1, 1965

By T. S. Spicer

Inflammability and crossing point apparatuses were used to study the influence of increasing amounts of such inerts as ash, fly-ash, pyrite, limestone and Portland cement with several pulverized bituminous coals. The results indicate that it requires large proportions of inerts to substantially suppress the ease of ignition.

Jan 1, 1962

By Thon T. Gin

The lithologic, mineralogic, and magnetic beneficiation characteristics of the iron formation at U. S. Steel's Atlantic City Ore Mine, Fremont County, Wyoming, have been determined. The iron formation averages about 30 percent Fe content, and varies from 125 feet to about 500 feet in thickness. It is composed of interbedded magnetite-rich quartzites, magnetite-quartz-amphibole schists, and amphibole-chlorite schists. Quartz, actinolite-tremolite, chlorite, and magnetite are the essential mineral constituents. These rocks are differentiated into four major ore types on the basis of their relative quartz and amphibole content. The iron content of the magnetic concentrate decreases and the silica content increases with decreasing grain size and increasing amphibole content in each ore type at the same fineness of grind. Criteria were developed to enable the mine operator to recognize the ore types and to blend them to produce a more uniform concentrator feed. This results in less variation in product quality and requires fewer changes in operating conditions-in the concentrator.

Jan 1, 1965

A significant technological development is discussed for the processing of certain problem power plant flyashes which contain a high water soluble mineral content and which are known to yield inferior flyash based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash based structures. Favorable changes are evident in (1) sodium silicate consumption, where often approximately one-half of the amount used for making brick from normal flyash is required; (2) processing costs; and (3) strength and appearance of the resulting freshly formed green and fired structural products. In some high cost instances-(above the cost of 30 dollars or less per thousand brick estimated for normal flyashes) hydrochloric acid additions can replace or reduce other costly additives required with problem flyashes to result in a savings of as much as nine dollars per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble, sulfur as a result of the eventual application of certain experimental air pollution control processes.

Jan 1, 1968

By Pramod C. Thakur

Coal is a major source of energy in the world today and will, undoubtedly, continue to be so for the next few centuries. Naturally, a great number of studies has been made of its physical and chemical properties. Unfortunately, the work on technical properties which influence the mining of coal and the consequent yield of inflammable gases and respirable dust particles has not progressed at a comparable pace. Coal is a brittle material. Irrespective of the mechanism of breaking coal, some dust is always produced. In mining parlance dust is defined as solid particle, smaller than 100 microns (micron = 10-6 meter), in size Coal dust, when raised into a cloud, creates two well known hazards in mines, namely, the coal dust explosion and Coal Workers' Pneumoconiosis (CMP). The latter is, perhaps, the greatest environmental hazard in U.S. coal mines today. In this context it is not only natural but also necessary to investigate the proneness of a coal seam to respirable dust production. It has been established that the amount of dust produced is a function of two groups of variables (1), (2), viz. (1) Material dependent variables, e.g., moisture content, compressive strength, hardness, etc. (ii) Breaking mechanism dependent variables, e.g., type of machine, depth of cut, etc.

Jan 1, 1973

By G. Davis

Mineral properties and mineral firms often trade at a market value that is significantly greater than the value indicated by discounted cash flow (DCF) techniques. A possible explanation is that DCF analysis does not consider the value derived from managerial flexibility. Presumably, then, at least some of the difference between DCF value and market value is due to managerial flexibility. This paper surveys the recent attempts to empirically quantify the value of managerial flexibility using option pricing theory. The results indicate that managerial flexibility, at least as measured by the option pricing methodology, falls well short of explaining the gap between DCF value and market value.

Jan 1, 1995

By W. A. Haley

As far back as 1939 state laws have required reclamation of mined lands. Reclamation has been the topic of many discussions and presentations, especially since the late 1960's. In the past ten years many states have added legislation concerning the reclamation of coal-mined lands. In the near future, it seems certain that some federal regulations will be passed that will set minimum guidelines for the states to regulate. Besides the requirement of returning the land to the approximate original contour, future regulations will more than likely demand replacing topsoil from one to five feet thick. As regulations become more stringent, costs will rise accordingly. Since no one has developed a machine that can do all reclamation work by itself, it is necessary to review in detail the tools available and to select the most economical means.

Jan 1, 1976

By David A. Zegeer

It's a pleasure to be here, and an honor to be invited to address this distinguished group of professionals. Today, I'd like to begin with an overview of progress in coal mine safety and health. I'll discuss some current areas of concern. And I'll make some suggestions as to where we may be headed in the future. This year marks the coal industry's 15th anniversary under the Coal Mine Safety and Health Act, which took effect in 1970. We have come a long way in those 15 years. As a coal mining man from way back, I remember the era when the Coal Mine Safety and Health Act first was passed. Some of you may remember it, too. At that time, the safety and health of coal miners was in the public eye even more than it is at present. One reason was a mine explosion that killed 78 miners when it occurred in a large underground coal mine in November 1968. That disaster raised tremendous public concern about protecting the safety of miners.

Jan 1, 1985

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC, and was installed on a shuttle car in a conventional room and pillar mining section. The purpose of presenting the information is to prepare mine operators for proposed legislation that will require shielding on low-voltage trailing cables. Specifically, machine modifications are required to cable reels, packing glands, and couplers. Cable splicing is not as complex as expected but additional materials are needed in the kit and splice training is necessary. Even though shielding will cause some problems for the mine operator, it can reduce the hazard of electrical shock to mine workers. This paper will present information that mine operators can use to solve most of the problems that will be encountered if they are required to install shielded cables. The in-mine evaluation was funded by the U.S. Bureau of Mines.

Jan 1, 1980

By A. V. Castelli

Since the record year of 1981 through 1985 the tonnage of weighting materials (barite and other heavy minerals) used in drilling fluids has decreased an estimated 49%. As in the past, barite still makes up over 90% of the minerals used for weighting materials in drilling fluid. Domestic production of barite has decreased 69% since 1981 and imported barite has made up over 50% of the total barite consumed since 1982. See Figure 1 for usage of barite. The number of operating grinding plants has decreased from 69 in 1982 to 39 at the end of 1985. With the decrease in demand of weighting materials for drilling fluids and an over capacity of grinding existing, prices for weighting materials have decreased dramatically. Although the American Petroleum Institute has not changed any of the specifications for barite, some users have initiated their own new specifications and have proposed to have them included in the API specifications. The exploration for and development of oil and gas dictates the level of weighting material used in the drilling fluids industry. Most forecasters do not foresee (or predict) increases in the level of drilling until the 90's. The primary or unground barite produced in the U.S. mines has a difficult time competing with imported barite due to the location of the mines. These mines are located in North Central Nevada, with small tonnages being produced in California, Missouri, Illinois, Montana and Washington. The major reason, is the difference in transportation costs from the mines versus ocean freight rates from the foreign ports to the major area of use, the U.S. Gulf. Since 1981, the production of primary barite has decreased from 2,849,000/ST (2,584,596/MT) in 1981 to an estimated 890,000/ ST (807,403/MT) in 1985(1). If it were not for the use of unit trains by some producers the production of primary barite in the U.S. would have probably declined another 20% in 1985. During the same period, of the total amount of barite consumed in the U.S., imported barite ore increased from 417, in 1981 to 65% in 1985. The major exporting countries to the U.S. during this period were China 46.27, Morocco 15.27., Chile 10%, Peru 8.4%, India 7.9%, Mexico 5.4%, Thailand 3.9% and Ireland 2.3%.

Jan 1, 1986

By James Wm. White

Calculation of consistent steady-state mass balances in operating metallurgical plants and pilot plants is of interest for many reasons. In general, enough data can - and should - be collected to overdefine the system, i.e., permit calculation of nonmeasured quantities via more than one path. In such cases, resulting steady-state metallurgical mass balances rarely close due to sampling, analysis and/ or instrument error. Indeed, determination of a valid calculational sequence for complicated process flowsheets with multiple recycle streams can prove quite difficult. Here we present and discuss a method that has proven useful in analysis of numerous grinding circuit flowsheets of varying-degrees of complexity our technique requires only a consistent process flowsheet with appropriate associated data and arbitrary numbering of streams and equipments. Process topology and user data are decoded to yield a set of "search" or base variables and a set of "calculated" variables in solids, water, particle size and splitter parameter space. This procedure greatly speeds subsequent actual mass balance adjustment calculations since perturing certain variables (e.g., a solids value) does not require recalculation of other variables (e.g., the water balance). Finally, internal search and calculated variables are back converted to User units and used in a Sum-of-Squares criterion. Global minimization of this performance functional then yields a consistent mass balance in a least, squares sense. Weighting factors of choice can be used. Examples illustrate application of these methods.

Jan 1, 1979

By G. J. Joy, J. P. Rider

Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 30 m/min (100 fpm). This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the U.S. National Institute for Occupational Safety and Health (NIOSH) is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research (OMSHR) Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities — 152, 213 and 274 m/min (500, 700 and 900 fpm)— and at water pressures of 689, 1,034 and 1,379 kPa (100, 150 and 200 psi). Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Average reduction efficiencies of at least 90 percent were seen at the three sampling locations closest to the shearer for all three manifold systems at nozzle spray pressures greater than 689 kPa (100 psi). Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer, a spray manifold was fabricated and evaluated at an underground operation.

Jan 1, 2016