Search Documents

By Immo H. Redeker

This is a final progress report on a cooperative project conducted by three private feldspar companies,** North Carolina State University, and the federal Bureau of Mines. The object of the project was to reduce the feldspar tailings disposal problems at the flotation plants in the Spruce Pine area of North Carolina. The initial phase of the project revealed that high tonnages of saleable feldspar and quartz were lost in the tailings and the three feldspar companies are now concentrating their efforts on feldspar recovery, either by reclamation from the tailings as suggested by the Asheville Minerals Research Laboratory or by improvements in metallurgy in the existing plants.

Jan 1, 1970

By Frank C. Appleyard

As the environmental movement gained force during the past few years, it was inevitable that attention would be focused on surface mining, and we have seen this method of extracting minerals from the ground come under heavy attack by conservation groups, the press and television, legislators at all levels of government,, and the public at large. It is difficult, and in some situations, perhaps impossible, to measure either the need for, or the results of, land reclamation in absolute terms. Therefore, much of the criticism of surface mining has been based upon subjective analysis rather than hard data, with the result that discussion of the subject often includes a fair amount of emotional response. To be fair, this reaction is not limited to just our critics; even we hard headed engineers sometimes respond in the same way, an observation with which you may agree when I finish this talk. This leads to the thought that whether you are for it, or against it, land reclamation in many respects is a state of mind. That is, our reaction to it can vary considerably, depending on how far we have thought it through. And think it through we must, because the pressures being brought to bear need to be met with positive actions if the problem is to be brought under control, and in the next few minutes I would like to discuss from a management point of view some ideas which might aid in this thinking process. It would be a mistake, I believe, to think that the current energy crisis will suddenly bring the environmental movement to a stop, and therefore, we can relax and go back to running our busi¬ness the way we used to. This is not realistic; on the contrary the energy crisis is focusing attention on the limitations of our natural resources as nothing else could, and with respect to land

Jan 1, 1974

By Edward J. Budill

One of the most dramatic innovations in the materials handling industry has been the development of stacker cranes and automated material handling systems. The stacker crane with its many capabilities and the development of reliable industrial automation controls have combined to produce dramatic achievements in an area once characterized by inefficiency lack of management attention, and capital investment. In many areas of application however, stacker cranes and high rise storage systems have been designed and installed with insufficient thought given to their integration into the overall operations of the plant or distribution facility. This paper will look at some new and interesting breakthroughs in the integration of stacker cranes and high rise storage systems into the total manufacturing plant system. In this paper we will refer to both bridge type stacker cranes and aisle stackers. The bridge type stacker crane was developed first and was initially developed with forks or other handling devices hoisted up and down a rigid or telescopic mast. This mast system was suspended from a trolley mounted on an overhead crane bridge. Today, the primary application of the bridge type stacker is in warehousing systems for handling basic metal products such as coils, bars, sheets and plates. There is no question that the bridge type stacker has achieved notable results in storage and handling of these commodities. However, a new area for stacker crane application has been developing which in many cases over-shadows the accomplishments in the storage area. This is the application of the bridge stacker as an integral part of the manufacturing processes, or in other terms the production applications of stacker cranes. The stacker crane has a number of attributes which makes these applications very important. First, the crane bridge provides the stable platform for the mounting of machinery which can accommodate the hoisting and lateral movement of large capacity loads. Today stacker cranes are being built with capacities of up to 30 - 40 tons. The bridge cranes can easily accomplish accommodation Of these large tonnages. Secondly, the mast system provides a stable platform for the mounting of a wide variety of manipulating devices which can be used for the placement of material into manufacturing processes, the extraction of this material from these processes, and movement to other points in the process area. These attributes combined with excellent operator control and safety have led to development of the stacker crane as a production tool.

Jan 1, 1973

By Gerald W. Cormick

In a complex society such as ours, the range of "negotiating" relationships is constantly increasing. These negotiating relationships have emerged as a direct result of the diffusion of power or influence to new sectors and emerging concerns. Even within organizations, the myth of the authority-based heirarchical structure has given way to the reality of constant negotiations between superior and subordinate and with peers in the organizational structure. In the broader context, the corporate organization finds it necessary to reckon and often negotiate with organized employees, suppliers, buyers, government agencies and a range of organized private interests ranging from minority groups to environmental organizations. In response to this diffusion of power and the conflicts which it has engendered, a variety of conflict avoidance, conflict managing or conflict resolution techniques has developed. The purpose of this paper is to attempt to differentiate between some of the conflict intervention approaches which have appeared "on the market", and to suggest three bases for selecting among them: 1. The "role" of the conflict intervenor; 2. How far the conflict has developed; and 3. The breadth and impact of the issues involved.

Jan 1, 1979

By Arthur R. MacPherson

Primary autogenous grinding has been in general use for somewhat over 20 years. During this period there have been many highly successful plants built on this principle, while some others have had problems such as: 1. Not performing as predicted from test work. 2. Highly fluctuating tonnage rates. 3. Mechanical problems. 4. High liner wear. Many of the problems with commercial autogenous mills have resulted from improper sampling and testing of the ore during the development period. It is recognized that the fully autogenous mill is very sensitive to any changes in grindability which may occur in the feed to such a mill. The semi-autogenous mill is somewhat less sensitive, but large swings in grindability of the feed require adjustment of ball charge and this cannot be easily accomplished in a short period of time.

Jan 1, 1976

By R. B. Hawkins

The discovery of the gold deposits of the Jerritt Canyon district and the construction of the E. R. Bell Mine is one of the significant mining developments in the United States during the past ten years. This mine will exploit one of the larger deposits of disseminated gold presently known, with proven, recoverable reserves in excess of 67.6 million grams of gold. Interest generated by the success of this project has contributed greatly to the tremendous resurgence in exploration for disseminated gold deposits in Nevada and throughout the west. The Jerritt Canyon project, including the Bell Mine, is a 70/30 joint venture between Freeport Gold Company and FMC Gold Incorporated, both of which are wholly owned affiliates of the respective parent companies, Freeport-McMoRan, Inc. and FMC Incorporated. Under the terms of the joint venture agreement, Freeport Exploration Company, another Freeport-McMoRan affiliate, manages the exploration and pre-mine development. Drilling, design, construction and management of the Bell Mine are provided by Freeport Gold Company.

Jan 1, 1982

By Brij M. Moudgil

Florida produced more than eighty percent of domestic phosphate during 1974. This amounted to more than thirty-five million short tons. Ninety percent of this production was used in the production of fertilizers. Other uses of phosphate include food preservatives, fabric dyes, optical glass, photographic films, soaps, plastics, pharmaceuticals and animal feed ingredients. Marketable phosphate rock projections for the nest decade forecast a very healthy growth for the Florida phosphate industry. Associated with the expansion, however, are the corresponding problems of water conservation, air and water pollution and land reclamation. Recognizing mining as an interim land use, the industry is presently engaged in a very active reclamation program. The proximity of the central Florida deposits to rapidly developing urban areas makes it important to undertake successful and well planned reclamation programs. Water use and conservation is of vitil importance to the industry. Water withdrawal from existing aquifers and discharges into drainage systems are closely regulated by state agencies. Water is stored and recycled to maximize usage. In some instances water is even returned to major aquifers through a series of recharge or connector wells. The phosphate industry has spent over 200 million dollars in the past decade for research, development and implementation of pollution abatement and water conservation systems.1 The following discussion outlines various phases of phosphate mining in central Florida today, with emphasis on research in waste disposal techniques and progressive land reclamation programs.

Jan 1, 1975

By Ray E. Harris

A resource of 134,400,000,000 tons of minable trona and mixed trona and halite underlies an area of about 1,300 square miles vest of Green River, Wyoming (Culbertson, in preparation)(Figure 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6,667,000 short tons (Kostick, 1983), approximately 90 percent of which came from Wyoming trona. This enormous resource occurs in the Wilkins Peak Member of the Creen River Formation (Eocene). The Green River Formation is derived from sediments deposited in a large lake (Lake Gosiute) that occupied the Green River Basin in south-western Wyoming 38-54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition during which time the trona deposits were formed. A total of 42 trona beds are known, of which 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation).

Jan 1, 1984

By William J. Shampine

The Floridan aquifer, which underlies all of Florida, yields water with a sulfate content of less than 50 parts per million in the north-western part and throughout most of the center of the State. In the southern part of Florida and along the most of the east coast, the sulfate concentration generally exceeds 100 parts per million and is as much as 1,700 parts per million. The sulfate concentration tends to be higher in the deeper zones of the aquifer. This map shows the sulfate concentration in the upper part of the aquifer. Sulfate is found in almost all natural water. Sulfate in rainwater is dissolved from impurities and gases in the atmosphere. Rankama and Sahama (1955, p. 314) report that the average sulfate content of rainwater is two parts per million; however, concentrations have been as high as 283 parts per million. Much of the sulfate in rainwater comes from hydrogen sulfide gas which is generated in shallow water on the continental shelves. The combustion of bituminous coal used for heating and industrial purposes seems to be an important local source of sulfate.

Jan 1, 1966

By David A. Campbell

There has been a long history of ironmaking on the North East coast of England centered around the River Tees. The industry developed here because of the availability of good coking coals to the North in Co. Durham, and the discovery in 1851 of ironstone in the nearby Cleveland Hills, South of the .River. Cleveland ironstone is relatively poor in quality, with an iron content not exceeding h% and high proportion of sulphur and phosphorous. The iron exists in chemical association with alumina and silica, and physical beneficiation processes involve a serious loss in iron unless the upgrading is limited, when the economics of the process become doubtful. Over the years, richer foreign ores have replaced the local ironstone, and the last operating mine was closed in 1964.

Jan 1, 1982

By S. S. Peng

Since the introduction of shield supports in 1975, safety and production in U.S. longwall faces have improved considerably. Many faces had a daily production of up to 8,000-10,000 tons and productivity reached 600 tons per man-shift. But a longwall face requires expensive equipment which slows down the growth rate of the percentage of longwall production. Among the equipment cost the shield support accounts for 50-60%, a very large proportion. Therefore, it will have a large impact on the growth of longwall mining in the U.S. to reduce the support cost (1).

Jan 1, 1988

By J. C. Draper

This subject was introduced last April in a paper presented in Birmingham, Alabama, by James E. Elkin, General Superintendent of Duquesne's Coal Department. This paper will cover some of the same data and in addition it will update and further describe our experience. Our Portal No. 3 was started in June 1965 with battery tractor-trailer face haulage. This mine is operating in the Sewickley seam in Dunkard Township, Greene County, in Southwestern Pennsylvania as shown on Fig. 1. The Warwick group of mines fronts on the Monongahela River and extends westward for some ten miles as shown on Fig. 2.

Jan 1, 1968

By A. W. Laughlin

Analytical costs are a major part of exploration programs in developing nations which may lack adequate laboratories. Laser-Induced Breakdown Spectroscopy (LIBS), a variant of atomic emission spectroscopy, can reduce exploration analytical costs and can provide the analytical results in <1 minute. CPI is now marketing battery-powered, backpack mounted analyzers, using LIBS to analyze for many elements of interest to the explorationist. LIBS is well suited to the analysis of elements in industrial minerals. Limits of detection in ppm for some of these are: Li-1, Be-2, Na-100, B-33, Sr-10, Ba-300, Cs-1, K-500, Fe-500, Mg-500, and Ti-500.

Jan 1, 1999

By J. Duran

Mining at Phoenix is currently done by surface operation in the Fortitude and Bonanza Pits, at a combined rate of approximately 110,000 tons per day. A portion of the ore bodies targeted by these pits was mined previously by underground mining methods, dating back to the mid to late 1800?s. Most of the underground workings (voids) are located in the west central area of the Bonanza Pit. The surface operation requires excavation through voids, and there is a risk of pit floor subsidence that has to be addressed. This paper presents a review of the risk mitigation measures that were implemented to reduce risks to people and equipment working in the area.

Feb 23, 2014

By W. E. Lamont

As part of its program to minimize mineral and metal needs, the Federal Bureau of Mines conducted investigations to determine the feasibility of producing foundry-sand-grade olivine concentrates from low-grade sources. Using a Bureau-patented attrition-grinding technique, concentrates meeting Steel Founder&apos;s Society of America (SFSA) specifications for loss on ignition (LOI) were prepared. Studies showed that green strengths and tensile strengths of the attrition-ground olivine were equivalent or superior to those of commercial materials. Metal-casting studies showed that molds of attrition-ground olivine produced better surface finishes. The improved surface finishes were attributed in part to increased grain sphericity.

Jan 1, 1977

By T. S. McGahey

The southeastern region of the United States has long been a major market area for coarse and medium particle size natural ground calcium carbonate fillers. The primary market for calcium carbonate in the southeast traditionally has been as fillers in building materials such as carpeting, joint cement and roof shingles. In these applications the economic value of the calcium carbonate in the final product is weighted more toward lessening the cost of the final product, as opposed to contributing any desirable physical characteristics. For example, in carpet backing applications the calcium carbonate filler does little more from a physical standpoint than add weight and body to the backing adhesive. The important factor in the use of calcium carbonate in carpet backing is that it can be used at high loading levels to replace the more expensive latex binder, thus lessening the cost of the final product. It is estimated that calcium carbonate producers in the southeast sell in excess of 200,000 tons (181,436,000 kg) annually for use in latex compounds for carpet backing applications.

Jan 1, 1986

By S. K. Kawatra, J. A. Halt

"INTRODUCTION Iron ore beneficiation needs advances in areas such as process control, automation, burner and furnace designs, silica-free binders, and even alternative iron making routes. While some – like new binders – are only step-changes, all are tools that can help make the ironmaking industry more sustainable. This paper focuses on binders. Binders are added to iron ore fines before they are agglomerated. Binders are used to control the balling process and increase the mechanical quality (e.g. strength) of green-balls and pellets. Agglomeration usually follows thickening and filtration. Good-grade ores, which don't require upgrading, are wet ground to decrease particle size and increase specific surface area. Low-grade ores are often extensively upgraded through wet operations (flotation, dispersion and selective flocculation, magnetic separation, etc.). For both types of ores, thickening and filtration conclude the circuits so that moisture contents are lowered and the ores can be agglomerated. It's been known for a long time that thickening and filtration behaviors are influenced by zeta potential (Sandvik, 1979). Highly-negative zeta potential is good for dispersion while low zeta potential is good for filtration. So, the zeta potentials of iron ore particles are lowered with additions of acid or carbon dioxide, for example, to increase filtration rates and throughputs (Eisele et al., 2005). What happens to particles as their zeta potentials are lowered? Particles aggregate together, effectively forming larger particles. How stable then, are those aggregates during mixing and balling? Are they easily broken up during mixing (if mixers are even used)? Are they broken up during balling? Or, do the aggregates resist breakage so that the availability of ultra-fines, which are so beneficial for agglomeration (Stone, 1968), is decreased? For plants where high doses of bentonite are used as binder, the above questions may be of no concern. The bentonite adds the necessary amount of fines; however, even at those plants, the calcium and magnesium contents in the water affect bentonite's effectiveness (more magnesium and calcium means less effective bentonite). (Engesser, 2003) For plants where new silica-free organic binders are being developed and used, the above questions may need to be considered. The binder is only amongst the iron ore particles for a short period of time – until it burns away or thermally decomposes in the induration furnace – so the liberation, availability and distribution of fine particulates is very critical for the quality of balls and pellets. It was hypothesized that high zeta potential conditions would lead to good pellets, while low zeta potential conditions would lead to relatively bad pellets."

Jan 1, 2018

By D. Shuck

Incorporation of a 2,727 mtpd, $5.7 million flotation circuit into the Mclaughlin flowsheet was completed in November 1991. This capital addition reduced overall operating costs and improved the gold recovery of the low grade refractory reserves over that expected for direct cyanidation. In addition, flotation provided a means to generate a sulfide concentrate which is utilized to supplement feed to the pressure oxidation circuit.

Jan 1, 1994

By John W. Leonard

The typical tunnel boring machine in use on today&apos;s tunnel project uses 15&apos;2-inch diameter cutters at a nominal load of 45 kips per cutter. The cutterhead rotates at a speed of 120 over D revolutions per minute where D is the cutterhead diameter in feet. The typical machine operates about 50 percent of the time. Delivery of a new machine takes 12 to 15 months. The TBM is a specialized tool and not applicable to all jobs. There is a range of job conditions that limit the economic use of a TBM. The machine should provide a thrust per cutter at least twice the compressive strength of rock in psi and up to three times the rock strength is required if in "granitic rocks." The rock strength in psi must be at least three times the cover above the tunnel in feet or the machine may stick. For example, 2,500 feet of cover requires at least 7,500 psi rock to avoid problems. When the RQD&apos;s over a significant distance of the project are less than 50, the TBM becomes support-bound. When a large percentage of the time is spent waiting while the ground is supported, the TBM cannot perform well (See Figure 1). This problem increased inversely with tunnel diameter. We are finding that increasing the RPM&apos;s does not significantly increase progress. The increased RPM results in a substantial decrease in cutter penetration. The explanation for this decrease appears to be vibration, cutterhead drag, or lack of stiffness in the cutterhead (See Figure 2).

Jan 1, 1981

By P. G. Irwin

Natural resins, those derived from coal and those mined in the Uintah basin, face challenges from synthetic resins that are derived from petroleum sources and rosin or wood sources. In the past, fossil resins from coal were produced by various companies, the last one being Hercules, Inc., which sold BLACKHAWK resin until a fire destroyed the plant in the mid 1970&apos;s. Approximately four to fjve million pounds of BLACKHAWK were produced and sold mostly to the printing ink industry. Uintaite, more commonly known as Gilsonite® resin, was widely used by various industries, notably in printing inks, coatings, stains, adhesives, foundry, asphalt paving, and oil well drilling muds. Gilsonite has lost market share over the last thirty years to various synthetic resins particularly hydrocarbon resins that are derived from petroleum sources.

Jan 1, 1990