Search Documents

Australian underground coal mines predominately use the longwall method for coal extraction. In longwall mining at least two parallel roadways known as gateroads are mined to delineate the sides of the longwall block, a longwall installation face is then driven connecting the gateroads to enable the longwall mining equipment to be installed. Roadway development should ideally be ahead of the longwall so that the longwall equipment can be installed into the newly developed panel with minimal delay to coal production. A discrete event model of roadway development can help assess how a particular configuration may perform with high levels of variability and uncertainty in operations. One of the major delays associated with roadway development is caused by the shuttle car due to its cyclic stop-start nature. Shuttle car travelling paths and machine interactions are normally constraint by the mine?s roadway layout and mine safety issues. This paper presents simulations of shuttle car route options which can be considered at the design stage to minimize the cycle time of a shuttle car as part of a general roadway development simulation model developed using 3D Flexsim.

Feb 23, 2014

By J. G. Groppo

In 1992, 48 million tons of fly ash (not including bottom ash, boiler slag and FGD material) was produced in the United States, according to the American Coal Ash Association. Of this amount, 27.2% was utilized; although the percentage of fly ash utilized increased from 20% in 1980, there is significant potential to increase utilization. One of the primary driving forces behind increased utilization is increased disposal costs due to more stringent environmental controls and regulation. Fly ash is classified as a natural pozzolan and finds significant use as a cement additive. It has been found to increase the plasticity of the cement mixture while lowering the amount of mix water needed. In addition to improving leveling and finishing properties, fly ash improves pumpability as well as decreases the heat of hydration of the concrete mix which is particularly important in massive concrete structures such as dams where the concrete needs to cool as quickly as possible. The Loss on Ignition (LOI) of fly ash is an important quality when considering utilization. The LOI is primarily due to the presence of unburned carbon and the standard specifications for the use of fly ash as a mineral admixture in Portland cement concrete are given in ASTM C618-89a. which sets an LOI limit of 6%. However, many states have set a more stringent limit of 3%. The primary reason for the lower LOI specification is that carbon adsorbs air entraining agents which limits freeze-thaw resistance. This is particularly important in climates such as the midwestern US where multiple cycles of freezing and thawing are typical in winter.

Jan 1, 1995

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994

By A. Z. Dimitroff

Immediate detection of methane buildup or of sudden liberation of large quantities of methane in the face area is essential to avert disasters in coal mines. Proper timely detection and handling of methane have always presented problems in extremely gassy mines, and these problems have been magnified by present accelerated mining methods. Strict rules and regulations have been established by coal-mining companies, States, and the Federal Government, which provide for periodic inspections for methane in face areas when electrical equipment is working. Other provisions require the operator' to shut down electrical face equipment and change or adjust ventilation when more than 1.0 percent of methane is detected. Nevertheless, human failure to detect such conditions has been responsible for numerous ignitions arid explosions Recognizing this fact, Marling J. Ankeny, former Director of the Bureau of Mines, proposed in 1958 the development of an automatic methane-monitoring device. He envisioned such a device as being entirely dependable, capable of giving a warning when a predetermined concentration of methane in air is reached, and capable of deenergizing the equipment and rendering it inoperative when a dangerous concentration of methane is present in the air. Such a device has been developed by the Bureau of Mines Health and Safety Research and Testing Center in Pittsburgh, Pa.

Jan 1, 1967

"The use of gas, temperature and airflow sensors to monitor mine ventilation atmospheres offers numerous safety and operational bene-fits to mines. Detection of dangerous gases, changes to airflows and temperature variations are some of the obvious benefits of using at-mospheric sensors in mines. The prediction of atmospheric conditions between sensors however is potentially difficult, and gaining full cover-age a mine will require either many sensors or a method of extrapolat-ing and predicting atmospheric conditions between and downstream from a sparser array of sensors. A dynamic simulation computer model technique is demonstrated to predict time based changes to atmosphere conditions downstream from sensors. The dynamic model predicts the time based changes to conditions throughout a mine model by simulating the mixing, addition and dilution of gases and airflow changes in incremental time steps. The advantages of this method is that a real time overview of full mine atmospheric conditions can be viewed at all locations, even areas without sensors. In addition, with careful planning and consideration of potential contaminant sources, the number of required sensors can be minimized. INTRODUCTIONMine Ventilation Sensors The importance of continuously monitoring mine atmospheres has been recognised since mining underground began and the effects of harmful gases on human health were discovered. Through the 19th and early 20th centuries, coal miners would take canaries underground with them as an early detection system against life threatening gases such as carbon dioxide, carbon monoxide and methane (Figure 1). The canary, normally a very songful bird, would become agitated, stop singing and eventually die if not removed from these gases, signalling the miners to quickly exit the mine (Davalle, 2011)."

Jan 1, 2016

By Dennis S. Kostick

Soda ash is produced in over 39 countries by the Solvay ammonia-soda process or by mining natural sodium carbonate deposits. The total production of soda ash in 1980 is estimated at slightly over 29 million metric tons. Synthetic production accounted for over 75% of this amount with the balance of production originating from natural sources (either trona or sodium carbonate-rich brines) found primarily in the United States, Mexico, Kenya, and Chad.

Jan 1, 1981

By Wi11iam I. Rau

In the recent past, there have been numerous projections of the capital requirements for additional mine and processing capacities required to meet projected non-Communist World demand for minerals during the next 15 years. A consensus judgment would place this currently at $14 billion per year, with the largest expenditures required for increases in aluminum and copper production. Until the early 1960's, internally-generated funds were used to finance nearly all of the large mining companies' capital requirements. Since that time, however, the enormous rise in capital costs per ton of capacity, accompanied by a relative stagnation in the financial condition of many of the major mining companies, have caused the industry to begin to rely on external sources for financing expansion, most notably, project financing from commercial banks and institutional lenders. Seven years ago, it was estimated that, in the five-year period 1972-1976,75% of the total capital requirements of $10 billion per year would come from internally-generated funds, with the balance to be provided by external sources. l There is little doubt that, in the coming decade, the percentage provided by external sources will increase. There should be little difficulty in attracting the necessary investment within the U.S., particularly in view of the expected continuation of companies in diverse industries seeking mineral investment opportunities. The more serious question lies in the availability of internal and external sources of funds for the expansion of mine and smelting capacity in the developing countries. Recently, R. F. Mikesell projected an average annual investment of $4.7 billion (in 1977 prices) over the 1977-1990 period would be required from foreign sources to expand metal producing capacity in developing countries. Mikesell concluded that external financing of mining projects in the developing world has averaged less than $1 billion per year over the past five years, thereby requiring more than a quadru1ling of this financing over the next decade.

Jan 1, 1978

By James K. Kindig

Solvent extraction as a method of purifying and concentrating metal values from solution has become a standard hydrometallurgical operation for recovery of both uranium and vanadium, and within the past two years it has been put into operation in a commercial plant for recovery of copper from leach solutions. In this first full scale solvent extraction plant for recovery of copper operated by Ranchers Exploration and Development Corporation near Miami, Arizona, a kerosene solution of an organic compound, LIX-64® is used to selectively extract the copper from the dilute acidic copper sulfate leach liquor obtained from heap leach operations. The copper is back extracted from the solvent into a stripping solution which is fed to an electrolysis circuit producing cathode copper for sale.

Jan 1, 1970

By R. Zins

During the past few years, a completely new concept has been applied to the design of drives for operating at very low speeds. In this, the motor is supplied by a variable-frequency thyristor cyclo-converter. Today, frequency converters with practically unlimited power ratings can be constructed. The system frequency of 50 or 60 Hz is reduced to about 10 % of these values. This makes it possible to operate the synchronous motor, which has a correspondingly high number of poles, at the extremely low speed of the driven mill, i.e, without interposed gearing. The first motors of this type were built to drive ball mills in the cement industry, which are very similar to those employed for ore processing. Here, too, the tendency is to build units of ever increasing capacity. In the case of conventional drives with mechanical gearing, this involves correspondingly increasing difficulties. These difficulties have prompted various studies of the possibility of applying the new type of drive to ore mills as well, but a gearless drive has not yet been built for this application. However, gearless drives for ore mills will certainly materialize soon and it was therefore considered a logical step to report at the A.I.M.E. Conference on the experience gained with these drives in the cement industry, and on the present state of development.

Jan 1, 1973

By C. H. Lee

The world-famous Sang Dong Mine in the Republic of Korea has long been one of the world's greatest tungsten ore deposits. Over the years, the development of the Sang Dong deposit has steadily increased to a point where it now exerts a great influence on the world tungsten market. The mine is located in the mountains of the province of Kang Won Do, approximately 150 miles by road due east of Seoul, the capital of the Republic of Korea. In recent years the transportation system in Korea has greatly improved and the mine is now serviced by an excellent secondary type road from the new railroad line which is 20 miles away. The Sang Dong operation is made up of the underground mining, beneficiation mill, chemical refinery, tungsten metal plant, bismuth refinery, acid plant, foundry and machine shops. The bismuthinite production from the Sang Dong Mine is also of considerable importance, The output accounts for nearly 10 per cent of the world production of bismuth. A small amount of molybdenite concentrate is also recovered from the flotation operation.

Jan 1, 1962

The rheological behavior of high concentrated coal -water slurry (cws), a new liquid fuel, is an important factor in the preparation, transportation and combustion. The conventional viscosimeters designed for Use with true fluids are not suitable to the measurement of the rheological behavior of cws. So that a special viscosimeter of tube type for cws was designed and set up in .laboratory. Experiments using two kinds of cws from two provinces from P. R. Olfna were conducted. It is found from test results that the experimental cws possess the rheological character of Bingham fluid and there is the existence of the wall effects which causes the measurement errors. In our former paper published the wall effects were discussed III the light of methods of Odroyd and Jastrzerbsiki to make the correction of the experimental results. But a number of tests are necessary to meet the need of determining the slip coefficient. In this paper the models of the wall slip velocity and the thickness of the slip layer of Bingham fluid were proposed III in theoretical approach which were satisfactorily used in the correction of the measured results of the rheological character of cws.

Jan 1, 1994

By R. D. Coursen

Tin has been one of the very few commodities which has been covered by an international commodity agreement. It is the only metal so covered. The reason behind tin's prediliction for an agreement has been the inconsistency of the price pattern for tin during the entire 20th century. It is not surprising in view - of the wide and wild fluctuations in its price that tin has been called the Cinderella metal. An examination, for example, of prices in 1977 alone attests to the erratic behavior of the tin markets. The high was recorded on October 27 at M$1,895 per picul and the low on January 3 at M$l,314 3/8, on the Penang market, a spread in Malaysian dollars of $581 for a picul weighing 133 1/3 pounds. The first steps in international cooperation on tin were taken after the price bonanza of the First World War. Despite a lack of increased consumption, and in spite of the fact there was no shortage of mining production during the war, prices boomed. Shipping shortages and thinning stocks brought about a situation where in the U.S., industrial stocks were only 1/6 of what they had been in 1914. The boom busted early. In 1921 the tinplate industry of the world had cut its output in half and total world consumption of tin fell by 1/3. Tin producers became so concerned that they created what was called the Bandoeng Pool. It accumulated stocks held by countries now known as Indonesia and Malaysia, amounting to 28 percent of the combined production of the two countries and about 15 percent of the total world for 1921. The pool holdings were shortly exhausted and thereafter in the years 1924 to 1928, general boom conditions existed for tin.

Jan 1, 1978

By Bruce Congleton

One year ago this month, we in Central Florida witnessed the beginning of a most exciting and glamorous attraction. After three years of construction and anticipation, Walt Disney World opened its gates near Orlando and during its first year of operation received a flood of over 10 million visitors---half of all who came to Florida last year! The side effects of this newest addition to Florida have been phenomenal. Traffic on heavy days has been backed up for 30 miles from the amusement park along a major interstate highway. Hotels and motels have been jammed packed for months, and reservations are still difficult to make. Gasoline stations, restaurants and souvenir shops are doing a booming business. Everywhere you look as you ride the highways of Central Florida you see the signs of growth. New hotels spring up almost overnight. Golf courses galore. New housing projects and apartments sprawl where orange groves used to be. New roads criss-cross areas which were once deserted. There seems to be no end to the steady influx of tourists and new residents to the Sunshine State. And it's mainly because that we are the Sunshine State that they come. Air and water pollution is and has been at a minimum in Florida. Pollution and emissions are fighting words among some groups dedicated to preserving the bountiful environment we share in Florida. Little wonder then that some of these people display concern when they learn that just 50 miles from the entrance to the Magic Kingdom of Disney, phosphate draglines strip away thousands of acres of land each year to extract one of our nation's most precious

Jan 1, 1972

By D. W. Tuckwiller

Electroplating is a widely utilized but little understood process. The fact that the average person is in contact with dozens of plated items daily without even being aware that they are electroplated is evidence of the success of the process. Although a complete explanation of electrodeposition involves thermodynamics and modern theories of bonding and catalytic reactions, in its simplest form the process conforms to the following description. A metal salt dissolved in water partially dissociates into negatively charged and positively charged ions. In the case of nickel sulfate dissolved in water, for example, a portion of the salt dissociates into positively charged nickel ions and negatively charged sulfate ions. If an electrical potential is applied between two electrodes in this solution, the nickel ions migrate toward the cathode and the sulfate ions toward the anode. The negatively charged cathode has a high concentration of electrons, which combine with the positively charged metal ions to form neutral metal atoms with a stable electron configuration. These insoluble atoms thus form a deposit on the cathode.

Jan 1, 1970

By Gerald Zink

The work described in this paper is sponsored by the Bureau of Mines for the purpose of accelerating the drilling of roof bolt holes and reducing the quantity of materials needed to fill each hole. A high-speed small-hole drill has been fabricated and tested in the laboratory. High priority has been given to safety, reliability, and compatibility with underground coal mining practice. The combination of drag bits and erosion jets is designed for high penetration rate, long wear life, and uniform hole size in a variety of sedimentary strata. A reliable high-pressure high-speed swivel feeds water to the bit at about 4 1/min (1 gpm). The duplex hydraulic intensifier which drives the jets has a 40 kw capacity (30hhp) Results of recent full-scale laboratory testing are presented.

Jan 1, 1978

By E. Lee

The behavior of As bioleaching using Acidithiobacillus thiooxidans (A. thiooxidans) in mine tailings containing highly concentrated As contents (i.e., As=33877 mg/kg) was systematically evaluated according to the changes in temperature (25?40°C, pulp density=0.5%, pH=1.8), pulp density (0.5?4%, temp=30°C, pH=1.8), and initial pH(1.8?2.2, temp=30°C, pulp density=0.5%). The changes in temperature and pulp density affected the As leaching behavior more than the change in initial pH did. Based on the pH and oxidation-reduction potential (ORP) results, the As leaching was attributed to solution acidification. In particular, As leaching was accelerated with increasing sulfate production in the reacting solution. After bioleaching, surface of tailings examined that many pores which dissolved As were formed by a chemical reaction due to bacteria. The As bioleaching efficiency by A. thiooxidans was enhanced by the oxidation of both the added elemental sulfur and the sulfur compounds in the mine tailings. The As bioleaching efficiency was maximized at 50.5% under conditions of an initial pH of 2.2, reaction temperature of 30°C, and pulp density of 0.5%.

Feb 23, 2014

By L. Yuan, J. Soles, W. Tang, R. Thomas

Lithium-ion battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12V, 24V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicated that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

Feb 1, 2023

By E. H. Cho

An acid mine drainage sludge sample containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn was obtained from the central part of West Virginia and leached with sulfuric acid at pH 3 and at room temperature. Air was bubbled through the leach solution to precipitate the iron content from the solution at pH 4.5. The leach solution contained 258ppm Zn, 105ppm Ni, 90ppm Co and 2050ppm Mn. Three distinctive solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA, Cyanex 272, and then Lix 84. The AIO ratio was 1 and the extractants were diluted 10 times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to pH 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1993

By M. A. Boucher

The purpose of my presentation is threefold: a) to make you aware of what is available in Canada in terms of refractory minerals. b) indicate the mineral deposits that have potential for development. c) show the advantages of Canada as a supplier of electrical energy necessary for the production of electrofused minerals. Canada is a producer of natural refractory minerals, electrofused minerals, and synthetic refractory minerals. Several deposits also have good potential for development. The natural refractory minerals produced in Canada are shown in Table 1. The major minerals by decreasing order of importance in terms of tonnage and values are: dolomite, graphite and magnesite.

Jan 1, 1992

By Abb Raymond

Finely processed industrial minerals in "powdered" form have long been utilized by the plastics, paint, rubber, paper, ceramics, and adhesives industries as fillers, extenders, coatings and special additives. These minerals, primarily calcium carbonate, talc, kaolin, titanium dioxide, and the like, have provided economic, uniform and consistent base materials which have, in turn, been used by the referenced industries to manufacture quality products. The focus of this paper will be the development of equipment and systems at ABB Raymond for the dry processing of such non-metallic minerals in order to meet what have become increasingly stringent requirements of the producers of these minerals. Changes in these requirements seem to have been accelerating rapidly during the last ten years, and it is expected this process will continue into the 1990's.

Jan 1, 1990