Search Documents

By W. C. Hellyer

In an autogenous grinding circuit in which feed at approximately nine inches top size is reduced to a size suitable for subsequent processing, the build- up of a "critical size" fraction in the media causes problems. A "critical size" fraction has been defined as, "media too small to effect reduction by impact grinding of ore coarser than a quarter of an inch and too large to be broken by the largest size of media in the charge. 9, (1) The buildup of a "critical size" fraction reduces the capacity of the mill, increases the grinding power requirements per ton of finished product, and generally produces a finer grind than is desired. It is general practice to overcome this problem by the addition of large diameter steel balls to the grinding charge. This has certain disadvantages, such as; (i) an increase in mill liner wear; (ii) wear on the steel balls, and; (iii) some loss in flexibility in grinding circuit operations resulting from difficulties in removing the steel balls by means other than by grinding out.

Jan 1, 1970

By C. C. Graham

In this paper, the problems which occurred on introduction of dense medium cyclone coal washing in Australia are reviewed together with the subsequent measures taken to obtain a satisfactory magnetite. Specification and testing of magnetite for exploration, quality control and in-plant check purposes is discussed. The disposition of Australian magnetite deposits in relation to the main coal producing areas is examined, and comments are made on the economics of mining, milling and beneficiating magnetite for coal preparation uses alone. Future trends in the Australian Coal Industry are predicted, and the need for a planned approach for the future is demons traced.

Jan 1, 1982

By James M. Barker

The occurrence of borates and zeolites at Mesa del Alamo is well documented by McAnulty and Hoffer (1) and Lefond and Barker (2). Further investigation indicates the presence of priceite and meyerhofferite in addition to the howlite (1) and colemanite (2). Analcime occurs in addition to the clinoptilolite and phillipsite (2). The Mesa del Alamo area is about 200 !a south of Tucson, Arizona, and 13 km southeast of Magdalena, Sonora, Mexico, just south of the unpaved road to Cucurpe (Figure 1). The geology and mineralogy of northcentral Sonora is known only on a regional basis except for small areas mapped in detail during copper exploration. The study area is within the Basin and Range province of North America from which borates and zeolites are now produced in California. The borates and zeolites at Mesa del Alamo occur in geological environments similar to those of the Mojave and Death Valley regions of California (3, 4). Thus, a detailed exploration pro- gram in the Magdalena area could result in the discovery of economic borate and/or zeolite deposits.

Jan 1, 1979

By Yuanhong Qi, Xun Fu Wang, Tao Fu, Kunkun Cui, Yingyi Zhang, Jie Wang, Junmao Qie

With the sharp decrease of sulfide nickel resources, the nickel laterite is becoming more attractive as nickel oxide, nickel matte, and nickel-iron. This study investigated the mineral phase structure, chemical analysis, thermal properties, and element distribution characteristics of the rotten rock layer deposited in the Southeast Sulawesi Ophiolite Belt. The results show that the nickel laterite deposited in Southeast Sulawesi Island, Indonesia, belongs to the typical high-nickel and low-iron garnierite-type laterite. The concentrations of nickel and iron of the nickel laterite are 1.99 wt% and 17.55 wt%, respectively. The serpentine, olivine, clay, chlorite, hematite, and magnetite are the major minerals, and the pyroxene, actinolite, limonite, and chromite are the minor minerals in the nickel laterite in Southeast Sulawesi, Indonesia. Serpentine and olivine are the main nickel minerals with an average nickel concentration of 3.65 wt% and 1.73 wt%, respectively. The Fe and Ni have homogeneity and symbiosis in the serpentine and olivine, and their concentrations are often positively correlated.

By G. J. Karabin

The Boundary Element Method of Numerical Modeling has become an increasingly popular rock mechanics -mine design tool. It has been used by the Roof Control Division, Pittsburgh Safety and Health Technology Center, MSHA, to aid in the resolution of complex ground control problems since 1985. This paper will present an overview of an evolving simulation process and details of methods utilized to generate necessary coal, rock and gob input properties. Also included is a description of a Deterioration Index System that is used to link model output to observed mine conditions and two case studies to illustrate that process.

Jan 1, 1995

By Leon D. Keller

Fine screening, as discussed in this paper, pertains to the use of the Rapifine DSM Screen to make a 65 to 325-mesh separation at production tonnages. The greatest number of Rapifine Screen installations are in magnetic taconite plants where the unusual relationship between the grinding mill, cyclone classifier, magnetic separators, and fine screens makes the Rapifine Screen application unique. Since the initial fine screening installation on magnetite in 1961, (1) additional installations and further testwork have contributed to the fund of information which is the basis of this paper. The addition of fine screens to the grinding-classifying circuit of a magnetic taconite plant creates a change that effects all components of the circuit. Pine screens in a non-magnetic plant have also been investigated, but here the benefits have not' been as clearly defined. Screens classify according to the particle size. Hydrocyclones classify by a combination of particle size and particle weight. The change in the type of classification minimizes overgrinding of the mineral. The resultant savings in grinding power can be used to increase the throughput, upgrade the product, or increase recovery.

Jan 1, 1971

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Jan 1, 1997

By A. L. Coello Velázquez

The subject of this paper is particle population balance models (PBM) that describe mineral impact crushing behavior; it is mainly concerned with the selection and fragmentation distribution function due to their importance in this context. The data obtained by Datta (1999) by applying impact pendulum testing to single limestone particles, used by Austin (2002, 2004a and 2004b) to obtain the principal parity of fragmentation functions, were processed in order to compare them with the results of other authors, such as Nikolov (2002 and 2004) and Vogel and Peukert (2003 and 2005) so as to increase knowledge of impact crushing. From this data it has been possible to obtain the performance models of the principal parameters of fragmentation function, thereby reducing the number of experiments necessary to model the impact crushing process. The authors also propose a simplification of the selection function model posited by Austin (2002).

Jan 1, 2011

By C. Bazin

The fundamental error associated to the sampling of heterogeneous ore particles is unavoidable and can only be minimized by an adequate selection of the sample mass and/or size reduction of the sample before division into sub samples for testing or assaying. The preparation of ore batches to carry out the mineral processing evaluation of an ore is a sampling process. The fundamental error associated with the division of the ore into batches is responsible for the differences in the composition of the batches. This paper attempts by various means to assess the reproducibility of the gold content of test batches prepared from a gold ore sample. The results of the investigation shows that for fine gold grain sizes the variability in the composition of the batches is less than that predicted by Gy?s formula and that the gold grain size is a strategic information in the assessment of the gold content variability of test batches.

Feb 23, 2014

By B. J. Arnold

During the past three years, coal samples covering a range of coal rank, ash content, size consist, grindability, and moisture content have been tested for their flow properties using a triaxial shear tester that measures the unconfined yield strength in a compressed sample of coal. The ratio of this unconfined yield strength to the sample bulk density is part of the equation used by handling system manufacturers to calculate the critical arching or critical ratholing diameter needed to ensure that coal will flow from bunkers or bins. This ratio also serves as an index to compare the flow tested. To test the applicability of the index to predicting problems with coal flow, a series of tests were conducted at CO Inc.'s Coal Quality Development Center (CQDC) in Homer City, Pennsylvania. Tests covering ranges in size consist, moisture content, and ash content were conducted by first filling a small two-ton bin with coal and then emptying the bin at a pre-set discharge rate. The actual discharge rate from the bin under the various conditions tested was measured. Samples of the coal discharging from the bin were collected. One sample was analyzed for ash, moisture, and size consist; another sample was sent to the Iowa state University for trivial shear tests (supplying an index measurement). Actual flowability results from the bin were then compared to the measured index to determine the applicability of the handleability index in actually predicting coal flow problems. This paper describes the correlation between handleability index and bin flow and explains the next stages of the project.

Jan 1, 1992

By Ottmar Burghardt

Sintering of iron ore has undergone a dramatic development world-wide. Today, the annual world production amounts to approximately 600 million tons. At present, the sintering process in competition with pelletizing, seems to offer certain advantages inasmuch as it allows the use of solid fuels. Also, its charging behaviour in the blast furnace is, in general, considered as being better than that of pellets. This is true, in particular, for the charging behaviour and the gas permeability in relation to the grain size. Moreover, instead of charging limestone into the blast furnace, for instance, the basic components which are necessary for the burden materials can generally be supplied in a simpler and more cost-effective way by using basic sinter instead of basic pellets. While in sintering, with basicity rising to the range of 1.6 to 1.8 CaO : SiO2, the capacity increases and the sinter quality shows improvements in most of its characteristics, the pro¬duction of basic pellets generally requires a higher fuel rate, when compared to acid pellets, while production capacity decreases and some of the quality characteristics deteriorate.

Jan 1, 1982

By W. K. Wedge

The chemical composition of the Pennsylvanian Bethany Falls Limestone Member of the Swope Formation was investigated using optical emission spectroscopy and both flame and flameless atomic absorption spectroscopy. Elements determined were Ca, Mg, Fe, Mn, AI, Si, Na, K, P, Ti, Zn, Cd, Ni, Co, Cu, Pb, Cr, V, and Mo. Over 100 samples were collected from active quarries along a 320-km-long (200-mile) outcrop in northwestern Missouri. Intervals were sampled representing uniform lithology to determine vertical and lateral geochemical variation. The Bethany Falls Limestone is the most extensively quarried Pennsylvanian limestone in Missouri. In 1975, 42 active quarries produced almost 5.4 million tons (6 million st) of stone valued at over 15 million dollars.

Jan 1, 1977

By C. M. Goodall

Solids and liquid phase residence time distribution data is reported for a laboratory column flotation cell. The effects of various physical flotation parameters on residence time distributions are reported and analyzed. A plug flow model with recycle is proposed for the froth phase and a tanks in series model for the pulp. By comparison of two and three phase residence time -distribution data it has been shown that the use of liquid residence time distribution data to predict the residence time distribution of the solids in a column is not valid.

Jan 1, 1990

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy's program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997

By X. X. Shao

Dewatering of ultra-fine clean coal slurry to a low moisture level of20 percent is difficult using the conventional techniques. A novel approach, which utilized mixing of fibrous waste material, such as paper, carpet and wood, with coal slurry prior to dewatering was developed. It was found that addition of about 10 Kg/t of carpet fibers or 5 Kg/t of raw paper pulp lowered the filter cake moisture from 22.5 to 18 percent. The compressive strength of the filter cake improved from 0 to 4.5 Kglcm2 and impact resistance from 0 to 4. The experimental data indicated that the handling character of the dewatered fine coal was improved significantly.

Jan 1, 1998

By S. A. Elmquist

Research activities performed by Cleveland-Cliffs Research and Hibbing Taconite plant personnel during the last decade have resulted in the development of an improved autogenous mill grinding circuit. Minus one (1) inch autogenous mill trommel oversize material, con-sidered to be a critical size, is magnetically cobbed and then crushed to 100% minus 3/8" prior to reentry into the feed end of the mill. Autogenous mill capacity increases, up to 25%, have been measured in pilot plant tests using this approach and are also anticipated for the Hibbing Taconite concentrator which presently has reached a 15.5% improvement.

Jan 1, 1994

By J. P. McKinney

A mathematical model is presented for the electrokinetic dewatering of suspensions of phosphatic clays. The modeling approach couples a boundary-element model for solution of Laplace?s equation to a recently developed constitutive equation that relates the change in solids content with applied electric field and time. The observation that the electric field controls both the maximum solids content achievable and the time required to reach that value is shown to severely constrain the application of electrokinetic dewatering strategies to an entire clay settling area. The approach, however, may be feasible for implementation as part of a continuous plant process.

Jan 1, 2011

By S. K. Kawatra

In many mining operations, particularly northern open-pit mines, large seasonal variations in grinding slurry temperature can occur. It is shown in this paper that this temperature shift can cause a winter-time loss in autogenous grinding efficiency of as much as 20Y. if it is not controlled. Laboratory experimentation indicates that much of this effect is due to increases in slurry viscosity as the temperature is decreased. An additional effect may result from changes in rock strength upon freezing, for which possible mechanisms are discussed. However, no effect clearly resulting from rock strength changes has been definitely confirmed.

Jan 1, 1990

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By B. E. Davis

A technique was devised by the Bureau of Nines to recover coarse (plus 1.7 m) North Carolina phosphate now discarded as waste. Concentration utilizes the difference in particle sphericity between the relatively flat calcite and the rounded phosphate pebbles. Sizing, treatment in a continuous hydraulic classification system, and grinding upgraded a 17.0-pct-P205 reject to 24.5 pct P205 with a phosphate recovery of 63 pct.

Jan 1, 1985