Search Documents

By Carl Erickson, James Hislop

INTRODUCTION As practiced today, longwall mining is a mechanical version of an established mining system. The equipment for longwall mining consists of four basic units: roof supports, face conveyor, winning or mineral-getting ma¬chine, and stage-loader conveyor. The system mines relatively thin slices of mineral across a predetermined face length in a virtually continuous sequence. As the winning machine cuts, the mineral is loaded automatically onto the face conveyor. In turn, the face conveyor is pushed over into the newly cut track by hydraulic rams attached to the conveyor and the roof supports. The roof supports then are lowered individu¬ally from the roof, advanced to the repositioned con¬veyor, and reset to the roof. At the end of the pass, the longwall cutter is pushed over, and a slice is taken in the opposite direction, so the system repeats itself. Fig. I illustrates a typical longwall mining system. The principle behind the longwall mining system is that the roof is supported only immediately adjacent to the worked seam, keeping the blocks of immediate roof clamped securely from the face to the rear of the sup¬ports. At the rear of the supports, the roof is allowed to fall and break up, with the swell of the broken material eventually establishing an equilibrium in the strata be¬hind the mined area. Fig. 2 illustrates the principle of longwall support. There are two distinct types of longwall mining. The longwall retreating system is the most common in the United States, South Africa, and Australia. The longwall advancing system is the most common in the re¬maining industrialized countries such as Britain, Ger¬many, Poland, and the Soviet Union. The longwall retreating system comprises a mining panel, where the roadways that form the head entry (end at which mineral is delivered from the face con¬veyor to a stage-loader conveyor) and the tail entry are predriven before the longwall units starts production. In the longwall advancing system, the longwall unit makes the head and tail entries as the face advances, utilizing various techniques to prevent the entries from being destroyed as they are left in a consolidating gob area. Fig. 3 illustrates the comparative approaches of the longwall retreating and advancing operations. As with most other underground mining systems, there are many variations on these two basic systems, using combinations of the systems that are dictated by

Jan 1, 1982

By B. J. K. Sullivan, Brian Hornsby

INTRODUCTION Mount Isa Mines Ltd. operates a copper and silver- lead-zinc property at Mount Isa in northwest Queens- land, Australia. Mount Isa is located in the tropics at latitude 20°43'S and longitude 139°30’E (Fig. 1). It is on the upper watershed of the Leichhardt River and at an elevation of 365 m above sea level. The average rain- fall is 360 mm/y, the greater part of which falls in January to March (the hot summer months). The mean summer temperature for these months is 30°C (dry bulb), with a maximum temperature of 43°C; the mean wet bulb temperature is 25°C with a maximum of 28°C. Mount Isa is located geologically towards the western edge of the Precambrian Shield of northwestern Queensland. This complex forms a north-tilting dissected peneplain which extends in the north-south direction for 640 km, with widths varying from 32 km to 190 km. The combination of differential erosion, regional strike, and steep dips has produced a corrugated topography of low north-south orientated hills and valleys. The field was first discovered in 1923 as a silver- lead-zinc field. Mount Isa Mines Ltd. was formed the following year and subsequently became the sole operating company on the field. Lead and copper ore have been mined and treated separately and simultaneously at Mount Isa since 1953. Intensive exploration commenced in 1954 and an active exploration program provided the justification for a series of production expansion programs in both silver- lead-zinc and copper (see Table 1 ). The most recent and largest production expansion program at Mount Isa commenced when a decision was reached in December 1969 calling for an increase in copper production from 100 000 to 150 000 t/y of blister copper. A major factor which influenced this decision was the substantial additions to the ore reserves in the so-called 1100 ore body which is a massive copper sulfide ore body with a known strike length of approximately 2500 m, a height which is variable up to 300 m, and a width of generally 300 m up to a maximum of 370 m (see Figs. 2 and 3). Host to the copper mineralization is a complex and variable rock generally called "silica dolomite." The ore body strikes 6.02 to 6.1 rad (345° to 350°), dips west between 0.78 and 1.13 rad (45° and 65°), and is truncated at depth by fault implaced basement rocks. It first occurs some 600 m below the surface and bottoms at about 1000 m below the surface. The unconfined compressive strength of the silica dolomite ore varies from 150 to 250 MPa, whereas the basement rocks, carbonaceous mylonite, slaty shale, buck quartz, and greenstone (a chloritic schist) are considerably weaker, varying in strength from 20 to 80 MPa. The distribution of mineralization within the ore body is variable, but can be considered as generally high grade at or just above the basement contact and diminishing towards the upper reaches of the ore body. The current

Jan 1, 1982

By S. C. Westerfeld

The original patent for the gyratory crusher was granted to Philetus W. Gates in 1881. This first crusher was used by the Buffalo Cement Co. At the time these early gyratory crushers were developed all mining and quarrying, either underground or open pit, was done by hand; tonnages generally were small and product specifications simple and liberal. Likewise plants were small and demands for small product sizes practically nonexistent. In addition to substantial amounts of hand labor, the available material handling equipment was small, simple, and not suited to handling large run of mine ore. Mine can, cable ways, or belt conveyon transporting crushed material to the mill had limited capacity per hour. At the turn of the century the largest Gates crusher, the No. 9, had a receiving opening of 21 x 48 in. with a three-arm spider and a 21 x 80-in. opening with a two-arm spider. The steam shovel began to change the entire picture of open pit quarrying. As a result of the use of steam shovels around 1910 crushers with 48-in. receiving openings were built; thus it can be seen that the basic gyratory crusher was developed prior to World War I. The improvement of the internal combustion engine and the use of pneumatic tires created a new set of operating conditions. Early mines were small, using shrinkage stoping and small mine can. The capacity of material handling was small, limiting the size of the largest piece and the feed rate. Improved material handling resulted in more and more large open pit mines with large shovels and a tremendous increase in the size of off road or mine haul trucks or rail can. Primary gyratory crushers also increased with receiving openings as large as 60 in. and connected hp of 1,000.

Jan 1, 1985

By Stephen Slot Odgaard, Simon D. Taylor

Phase One of Copenhagen Metro opened on October 19th, 2002 and is already a great success. 11 stations are open and Phase Two with 6 additional stations will open during 2003. Phases One and Two include 21 km dual track, whereof 10 km is in tunnel. 17 stations (six deep, three shallow, and eight above ground) will service passengers with trains running at 90 seconds intervals. This paper will discuss the various aspects of the Metro, where construction methods include TBM bored, NATM, Cut & Cover, Secant Piles and Diaphragm Walls.

Jan 1, 2003

By N. Djordjevic

Introduction The vibration energy that travels beyond the zone of rock breakage is wasted - all it does is cause damage and annoyance. Under favorable geologic conditions, this energy may travel many kilometers before it finally drops bellow the background noise level. This has forced the introduction of more restrictive limits to the allowable vibration levels. To maintain the profitability of a mine or quarry and to comply with environmental protection legislation, blasting needs to be performed in a more predictable way that will ensure that the final results are optimal in both mining and environmental terms. Minimization of ground and induced structural vibration is, therefore, a matter of good blasting practice -not just an attempt to avoid complaints from neighbors. A new approach to blast vibration minimization is presented. The method utilizes the existence of the local minimums in the frequency spectrum of single-hole blast vibration. The results are presented as a delay map showing maximum ground or structural vibration velocity for many combinations of interhole and interrow delays. A blast engineer can use this map to select an optimal combination of delays that will produce a low vibration velocity at a selected location and, at the same time, will be acceptable from the point of view fragmentation or muck pile shape. Response of structures A typical single-story building has two distinctive forms of vibration. The first form is a translatory vibration of the building superstructure (frame), and the second form is a flexural-bending vibration of the structural elements such as walls and floors (Siskind et al., 1980). Walls and floors will have several modes of oscillation. The most important is the fundamental mode of the vibration, as this mode will have the lowest frequency, the largest amplitude and will cause the largest deformations. The vibration of walls and floors is also a source of secondary vibration within a building, due to the movement of loose objects, e.g., furniture and wall fittings (Dowding, 1985). The subjective estimate of the amplitude of a vibration by the occupants of a house will be unrealistically high due to the effect of the secondary vibrations. It is now well recognized that human perception of ground vibration begins at levels that are far below those that will produce minor damage to the most fragile structures. In mining and quarrying operations, complaints regarding vibration levels tend to be determined more by human perception or annoyance rather than by observations of damage. Ground vibrations on the order of 0.08 mm/s (0.0032 ips) (Walter and Walter, 1979; Murray, 1987) can be felt, and they are often subjectively estimated to be about 100 times greater. Amplification of ground vibration in the structure depends on the amount of energy in the ground vibration spectrum that is in the vicinity of the structure's resonant frequencies together with the damping ratio of the structure at these particular frequencies. One way to avoid significant vibration amplification in a structure is to shift the dominant part of the ground vibration away from the resonant frequency range of the structure. The presented method allows for the selection of the optimum blast timing (interhole and interrow delay times) to minimize the resultant ground vibration amplitudes in a given frequency range. It also allows the selection of suboptimal, but still acceptable, blast delay times, which may be preferable from the point of view of overall blast performance. Determining frequency ranges of importance in structures In attempting to avoid amplification of vibrations in the structure, ground vibration amplitude of frequencies close to the resonant frequencies of the building needs to be minimized. The width of the frequency-minimization region is determined by the value of damping in the building. If the damping ratio is low, then the frequency-minimization region around the resonant frequency will be relatively broad. By shifting the dominant part of the ground-vibration energy into the frequency region much higher than the resonant frequency of the building (1.5 to 2 times), it is possible to achieve efficient vibration isolation of the building. In such cases, the structural dynamic amplification of ground vibration will be less than unity. The first step in this minimization process is the determination of the structural resonant frequency. From the frequency spectrum, it is possible to determine the resonant frequency of the structure. Sometimes the

Jan 1, 1998

By James J. Scott

I am indeed honored to be the 1991 recipient of the Daniel C. Jackling Award. To be voted this honor by my peers in the Society for Mining, Metallurgy, and Exploration and AIME means more to me than I can truly express. Daniel Jackling's position and prominence in the mining industry first came to my attention in the fall of 1949 when I transferred from Wisconsin Institute of Technology, then a three-year school, to the Missouri School of Mines to complete my last year for a bachelor's degree in mining engineering. I played basketball in the Jackling gym and ran track on the Jackling field. I didn't know a lot about Jackling then, except he was an honored graduate of the school and, obviously, supported the school financially. Over the years, Jackling's name kept coming up. He was a man with a reputation for being a doer, a mining leader who was always a step ahead, a mining engineer who knew how to motivate men in the working place, to organize mining systems, to finance and organize corporations. to open up new, low-grade ore bodies for exploitation. If Jackling were alive today, I would expect he would bean excellent candidate to apply practical rock mechanics to his projects. Looking over the list of Jackling Award recipients, I have known many, have met many personally and had a few who were dear friends that affected my own professional life. Ab Shoemaker, '58, and I consulted at the White Pine Copper Co. on mining problems in the 1960s. We arranged for our visits to the mine to coincide so that we could collaborate on our ideas. I would rent an auto and drive for Ab. He said he was the only mining engineer in the country that had a PhD for a chauffeur. James Boyd, '67, was my mentor as regards the White Pine Rock Mechanics Program that we organized in 1963. Only through Boyd's forsight. leadership, dedication and willingness to spend money on research and development did the Practical Rock Mechnics Program at White Pine succeed. He never wavered in his support to that program or to me personally. Tom Howard, '75, was my predecessor in 1970 as Director of Mining Research for the US Bureau of Mines. When I joined the Bureau in August 1970, he had the research centers up and running. Any successes I may have had with the Bureau of Mines were due in great part to Tom's leadership and organization throughout the 1960s. Gene Cameron, '68, was my teacher at the University of Wisconsin and I remember him fondly. He was the one professor who lectured in a manner that made me welcome going to his classes each day, a truly remarkable educator. If you have come today to listen to me talk about instrumentation, rock properties, stress-strain relationships, rock mechanics theory, etc., you will be disappointed. Large volumes of data have been collected by well qualified theoreticians to define stress-strain conditions in mines. Unfortunately, very little of this data has been used by industry due to the lack of initiative and understanding by the researchers to the true problems of implementation in the industry. I hope my remarks will assist future investigators to work through the maze of operational problems so they will experience the satisfaction of seeing their research used. I fully realize that the Jackling Award is given by the Society for Mining, Metallurgy, and Exploration and is primarily offered for accomplishments in hardrock mining. I have found it impossible to separate hardrock and coal mining when I talk about "Applied Rock Mechanics." There is too much overlap and the same mechanics principles are applied to both. For example, coal mine designs have been applied to salt, trona and potash. Also, the original layout and design of White Pine Copper Mine was based on coal mine designs. Any developments to apply rock mechanics ideas must

Jan 1, 1992

By Bernard L. Cohen

INTRODUCTION The most serious occupational radiation episode in U.S. history was the exposure of uranium miners to radon daughters in the 1945-1968 time period. Although the maximum permissible dose at that time was 12 WLM (working level months) per year, average exposures were several times that figure, and ten times higher exposures were not uncommon. Starting in the early 1960s, mounting epidemiological evidence appeared for an excess incidence of lung cancer among these miners; up to 1974, there was an excess of 134 cases (159 observed vs 25 expected) among the 4000 in the group under study (NAS-1980). When this excess became apparent, the Federal Government took jurisdiction, greatly tightened enforcement, and in 1969 lowered the maximum permissible exposure to 4 WLM per year. These standards were met largely by a great improvement in ventilation. As a result of these measures, average miner exposures were reduced 5-fold from 1965 to 1968 and by another factor of 3 by 1970. In 1978, the 4 WLM/year maximum permissible exposure was exceeded by only 37 of 7500 underground miners, for only 16 wars it exceeded by more than 25%, and for only 8 was it exceeded by 502 (AIF-1980). The average exposures to the various groups are listed in Table 1. We see that the average exposure for all miners was 1.03 WLM, and for those who worked essentially full time underground it was 1.45 WLM. For purpose of later discussion, it will be convenient to choose a single value for average exposures. In view of the fact that employment situations and job categories are bound to vary over a lifetime of work, we take this to be 1.3 WLM/year. The purpose of this paper is not to dwell on history, but rather to address the question of whether or not this present situation is satisfactory. This question was considered recently by a study group under the auspices of National Institue of Occupational Safety and Health (NIOSH-1980) and it answered the question in the negative, concluding that the maximum permissible exposure should be substantially reduced. However, their arguments were incomplete and were lacking in perspective. The principal thrust of this paper is to provide some of the material overlooked. RISK TO URANIUM MINERS FROM RADON EXPOSURE In order to quantify the risk to uranium miners under present working conditions, it is first necessary to estimate the risk of lung cancer per WLM of exposure. The most straightforward way of doing this is to use the data on the group of uranium miners under study. These are listed in Table 2 for 8 exposure ranges and for the total group (NAS-1980). If all data are given equal weight, the risk is seen to be 3.5 x 10-6 per year per WLM. Much can be said in favor of using this value for the risk as dose independent; it is within one standard deviation (SD) of the observations in 5 of the 8 dose categories (as expected from the definition of SD), and within 2 SD for all 8, and for the three cases differing from the mean by more than one SD, two are above and one is below. However, the uranium miner exposures in the present situation will be far below those covered in Table 2, so it is worth considering the possibility that the risk differs from this at low doses. From the last column of Table 2 we see that the experience from all exposures below 600 WLM indicates a risk higher than the mean for the entire group by more than two standard deviations (the value 600 WLM in this comparison was deliberately chosen to maximize this deviation; for exposures below 360 WLM and 840 WLM, the excess is only 1.0 and 1.6 standard deviations respectively). In view of this tendency for the risk to be higher at lower dose, we will take the risk to be 5.0 x 10-6 per year per WLM in what we will refer to as model A. This risk estimate is based entirely on exposures much [higher] than those that will be experienced by

Jan 1, 1981

By I. Meliadis

This study presents the methodology and proposals for the restoration of an abandoned quarry in the Greek island of Milos. The local data (soil, vegetation etc.) of the island were collected, analysed and compiled into thematic maps using Geographical Information Systems. The restoration plan was based on the G.I.S. database and suggested the revegetation of the disturbed lands with herbaceous (grasses and legumes) or woody (shrubs and trees) plants. Plants should be indigenous or from other areas with the same vegetation type. Herbaceous plants establish and grow easily protecting the soil from surface erosion. The revegetation success depends on the seed quality, planting season and methods as well as local environmental conditions. Our proposals aim to restore the abandoned quarry with methods that follow the natural succession of vegetation, have minimal environmental impact, low cost and the expected result will be similar to the surrounding undisturbed land.

Jan 1, 2002

By Brain W. Lawrence

Sublevel stoping generally is a large-scale open stoping method. It sometimes is referred to as long-hole or blasthole stoping. This method usually is applied to strong ore bodies that require minimal support and are surrounded by strong country rock. The ore body should be fairly regular in shape and well-defined. The dip of the footwall normally should be sufficient to allow broken ore to gravitate freely, although the method has been adapted successfully to mine some of the flatter ore bodies. Sublevel stoping is not dependent on the width of the ore body. Widths of less than 6 m (20 ft), however, make the utilization of long-hole drilling techniques more difficult. The main criteria for sublevel open stoping are competent ore and stable host rock, regular ore boundaries, and a footwall dip that exceeds the angle of repose of broken ore. Basically, the method entails providing access to the ore body at various subintervals between the main haul- age levels in order to drill and blast the intervening ore. Stope drilling is carried out from drilling drifts on the sublevels, and the ore is blasted in slices towards an open face, which generally is vertical on the downholes and may be inclined towards the open face for the up holes. The blasted ore gravitates to the bottom of the stope and is collqcted through drawpoints. Fig. 1 illustrates a typical sublevel stoping mine. The method requires extensive ore body development with relatively high capital expenditures. How- ever, much of the development is in ore, and production costs are comparatively low. Productivity rates are in the 13.6 to 27.2 t (15 to 30 st)/manshift range. The drilling, blasting, and loading operations are performed independently, and equipment utilization is high. Large outputs can be obtained with few units and limited personnel. Dilution with waste rock may occur if ore boundaries are irregular or if caving occurs, but 100% of the ore within the stope usually is recovered. Pillar recovery sometimes is a problem. It is at this point that most of the waste dilution occurs. At the time data was gathered for this report (1973), the sublevel open stoping method was used by more than 21% of the metallic ore mines in the US (9 out of 42 mines producing 1088 + t/day (1200 + stpd) and provided more than 12% of the total metallic ore production from these mines. DEVELOPMENT Access to a sublevel open stope mine is gained by a slope or shaft that is normally sunk in the footwall of the ore zone, away from any possible effects from blasting or other production operations in the stoping process. Main level interval is selected and usually varies from 45.7 to 121.9 m (150 to 400 ft), depending on the vertical extent of the ore body, the number of drawpoints required to maintain output, and the eventual stope height. The main haulage drifts are located at the bottom of the stope horizon, either directly in ore or in the footwall, with access crosscuts at intervals. Raises are driven up through the ore to connect to the level above and provide access and ventilation to the sublevel drilling drifts, which are driven horizontally in the ore for the length of the stope. Depending on the drawpoint system to be used, the stope is either undercut by a raise-and-cone system, from a scram or slusher drift, or simply provided with a drilling drift from which access is made at intervals to the main haulage level. A raise driven either at the end or in the middle of the stope (if stope access is from both ends) provides a start for opening up a vertical slot across the stope to establish a free or open face for long-hole drilling and blasting. Sublevel stoping has proved to be a relatively safe and economical system.

Jan 1, 1982

By Byron C. Hardinge, E. R. Palowitch, Albert W. Deurbrouck, David J. Akers, Edward R. Torak

During 1983, 42.2% of the 686.0 (624.3 Mt) million tons of coal reported, 289.6 (263.5 Mt) million tons were mechanically cleaned, of which 107 (97.4 Mt) million tons were cleaned by dense media (magnetite and sand) processes.' The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 38% between 1938 and 1983. The Electric Power Research Institute estimates that 150 million tons (137 Mt) of coal were cleaned by heavy-media processes in 1986, and that this number may increase to 265 million tons (241 Mt) by 1990.2 Dense medium separations include those coal preparation processes that clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes generally offer the following advantages over other coal cleaning processes: • Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of raw coal whose specific gravity is near the specific gravity of separation. • Ability to maintain a separating gravity that can be controlled within + 0.005 sp gr units. • Ability to handle a wide range of coal sizes. • Ability to change specific gravity of separation to meet varying market requirements. • Ability to handle fluctuations in feed, in terms of both quantity and quality. Unfortunately, dense medium processes can have the following disadvantages: • Relatively high capital costs caused primarily by the need for equipment to collect and recycle the medium. Relatively high operating costs caused primarily by operation of medium recycle equipment and loss of medium.

Jan 1, 1991

By Charles G. Frush

The function of the mine surveyor is to (a) provide a network of points of accurately known position, covering the entire mine property, (b) obtain the required data for the preparation of useful maps and sections! (c) provide position and directional control for the guidance of the operations, (d) measure the progress of the work, (e) measure the movement of rock masses, and (f) make miscellaneous surveys as needed. Mining properties range from the very small to the extremely large, and from those which involve only surface operations to those involving extensive underground workings. Active mines undergo constant change, necessitating continual updating of the surveys. The differences in the character of the deposits, the scale of mining and the mining methods result in large differences in the surveyor's activities and techniques, but many of the problems involved are common to most mines. The surface work of the mine surveyor is very similar to that, of the plane surveyor in that control points are established by triangulation, trilateration and traversing. Detail is taken by direct measurement, by stadia and by aerial photography. The equipment used, the techniques and the methods of processing the resulting data are likewise very similar. However, the underground work is quite different : A. The lines of sight frequently must be carried through constricted openings, often involving short lines of sight and awkward setups. B. The lighting often is poor, requiring illumination of the backsights and foresights, and the crosshairs. C. The ambient conditions often are difficult, involving falling water, high tem- peratures, poor visibi 'kv and heavy traffic through the area being suneyed. D. The surrounding rock map be unstable, resulting in movement or loss of the surveying stations, as well as hazard to the surveyors. E. The points to be measured often are difficult or impossible to reach. F. Steep vertical sights often are necessary, requiring the use of special equipment. G. Many working levels commonly are involved, requiring the transfer of position and orientation to each with a high level of precision. This section therefore will concentrate on surveying problems peculiar to the mine surveyor, chiefly underground work. 22.1-THE MINE COORDINATE SYSTEM A system of coordinates is essential for all permanent mining operations It is very desirable that all mining operations in a ,given area b~ tied into the same system, as this minimizes problems of boundaries and connections Whenever possible this system should be tied into and made part of the state or regional grid system. It is desirable to orient the coordinate grid on a true-north line and to position the origin of the coordinates so that all of the work will be in the "northeast" quadrant, making the north and east coordinates always positive. This can be done by subtracting suitable constant values from the north and east coordinates of the regional system The residual values are of more convenient magnitude and can be used as the local mine coordinates. If the long axis of the mineralization is not generally north-south or east-west.

Jan 1, 1973

By B. T. Stanley

Traditional methods of creating a water tight shaft liner involve the use of segmented or welded steel. When shafts are located in ground that exhibits extremely difficult conditions of high water inflow and hydraulic pressure, composite liners are often combined with ground freezing during construction. The authors were searching for a cost effective and more flexible solution to hydrostatic liners design than the traditional concrete/steel composite design used so far. Searching through new technologies developed for tunneling applications, sprayed on membranes systems seemed very promising but were not developed for the specific circumstances encountered in shaft sinking applications where ground freezing is involved. Even though freezing is a very effective technique, it creates adverse temperature conditions for the application of spray on membranes. In addition, application and hydrating cure times for those membranes products ranged between six to twenty-four hours under ideal conditions (usually temperatures well above freezing point), which eliminated them from consideration in a shaft sinking cycle. While researching different spray on membrane materials, it was discovered that Stirling Lloyd Polychem Ltd. has developed and proven a different membrane material for waterproofing liners in different tunneling applications. The characteristics of the membrane exceeds the pressure parameters encountered in frozen shaft sinking operations, and the chemical cure times were reduced to one hour per layer which worked well into the shaft sinking cycle times. More over their system included a quality control procedure that allowed insuring integrity of the membrane at application time, a very desirable feature for shaft liner construction. However, the frozen rock surface still presented an unknown in the cure time and stability equation. As all membrane products a shotcrete substrate is usually required prior to application. The hypothesis used by the author was to use this shotcrete layer, not only as a substrate, but also as a thermal insulation against the frozen rock and the membrane during both application and curing time. The authors knew from experience that shotcrete could be applied successfully over frozen rock. But the shotcrete temperature curve over time was unknown and no information were found in the available literature. Testing was required to determine whether a suitable mix of shotcrete could be applied to the frozen shaft wall to provide enough heat of hydration for a suitable period of time to create conditions suitable for membrane application and curing.

Jan 1, 2012

By Robert J. Henning

The term olivine was first used in 1790 by J. Werner, and the corresponding mineral was so named because of its olive-green color (Hunter, 1941). Olivine is the principal component of the rock known as dunite. While by classic definition dunite is composed of 90% or more olivine, commercial use of these terms has resulted in more specific definitions. Commercially, the term olivine is used to designate a material that consists of 85% or more forsterite and contains 45 to 50% MgO, 39 to 42% SiO2, 5 to 8% Fe2O3, and has an ignition loss (LOI) of 1 to 2%. The term dunite designates a rock that contains 36 to 45% MgO, 36 to 39% SiO2, and has an ignition loss of as much as 10% (Teague, 1983). GEOLOGY Olivine is found in basic igneous and basic metamorphic rocks whose age varies from pre-Ordovician to Tertiary. Economic deposits are of magmatic origin and are restricted to the dunite variety of the peridotite group of ultrabasic igneous rocks. Olivine also occurs in basic igneous rocks such as gabbro, basalt, and diabase and more rarely as an accessory mineral in granite and metamorphosed crystalline limestones. Mineralogy The term olivine refers to a group of orthosilicate minerals in isomorphous series with magnesium-rich forsterite (Mg2Si04) as one end member and iron-rich fayalite (Fe,SiO,) as the other. In most olivines the ratio of magnesium to iron varies from 16: 1 to 2: 1. Commercial olivine deposits contain a mixture of forsterite and fayalite with the fayalite content restricted to less than 15% (Reed, 1959; Teague, 1983). Accessory constituents may include primary minerals such as ilmenite, magnetite, diopside, chromite, and garnet and secondary minerals such as chlorite, serpentine, talc, and vermiculite as alteration products. Chemical and Physical Properties The chemical composition of olivine can be expressed as either (Mg, Fe), SiO, or 2(Mg, Fe)O.SiO,. Table 1 presents chemical analyses for some commercial olivines. The physical properties of olivine are shown in Table 2. Distribution of Major Deposits Commercial olivine and dunite deposits are found in Norway, Japan, Spain, India, Italy, the United States, Sweden, Austria, Pakistan, and Mexico. Noncommercial deposits have been reported in New Zealand, Zimbabwe, South Africa, New Caledonia, Greece, Brazil, and Canada (Teague, 1983). The present markets for olivine are characterized by low unit value, high volume, and high sensitivity to freight costs, so few deposits are commercially viable. Literature from the USSR indicates that considerable research on olivine refractories is being done. (Afansa'ev, 1988), lending credibility to the conjecture that commercial deposits are being mined there. In eastern Canada synthetic olivine is being produced by calcining chrysotile asbestos mine tailings. In the United States numerous lenses of olivine extend in a belt from northeast Georgia northeastward across western North Carolina. Total reserves in North Carolina and Georgia are estimated at between 125 and 200 Mt. The largest US deposit is Twin Sisters Mountain, located in Whatcom and Skagit Counties in the state of Washington. This deposit, which has an outcrop area of 93 km2 and a relief of about 1 525 m. is estimated to contain 1 800 Mt of fresh, unaltered olivine (Teague, 1983). In addition, the US Bureau of Mines reports reserves of 50 Mt on Cypress Island in the state of Washington, and the literature reports eight complexes in southeastern Alaska, some containing cores of olivine as large as 1.6 km in diameter (Taylor, Jr., 1967). The world's largest deposit of olivine occurs in the Aaheim area of Norway, where reserves are estimated at a 2 000 Mt. Several other Norwegian deposits contain as much as 5 Mt each. In Japan the production of ultrabasic rocks is currently about 6 Mtpy, but the bulk of this output is serpentinite. Olivineldunite accounts for only 17% of this production. The major olivine deposit in Japan is located at Horoman Hill on the northern island of Hokkaido. Reserves at this deposit are estimated at 100 Mt (Anon., 1990). Spain is one of the largest producers of dunite. Reserves in the La Coruna District in northwestern Spain are estimated at 100 Mt. India, also a major dunite producer, has a large deposit at Salem in Tamil Nadu. In Italy olivine/dunite is mined from a deposit near Turin. In Sweden the largest deposit is at Arutats and is reported to be comparable in size to the Twin Sisters deposit in the United States. At present the only production in Sweden is from a deposit 30 km south of the town of Gallivare. Reserves at this deposit are reported to be between 1 and 2 Mt. Other significant deposits are: 1) in Austria at St. Stefan near Leoben, 2) in the Swat District of the North West Frontier Province in Pakistan, and 3) in Mexico at Cuidad Victoria in Tamaulipas (Anon., 1990).

Jan 1, 1994

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.

By A. Cecala, J. Noll, J. Hummer

"NIOSH has observed that many control rooms and operator compartments in the US mining industry do not have filtration systems capable of maintaining low dust concentrations in these areas. In this study at a mineral processing plant, to reduce respirable dust concentrations in a control room which had no cleaning system for intake air, a filtration/pressurization system originally designed for enclosed cabs was modified and installed. Eighty-seven percent of submicron particles were reduced by the system at static conditions, meaning that greater than eighty-seven percent of respirable dust particles should be reduced. The particle size distribution for respirable dust particles are greater than for submicron particles, and filtration systems usually are more efficient in capturing the larger particles. A positive pressure near 0.02 inches of water gauge was produced which is an important component for an effective system and minimizes particles (e.g. dust) from entering into the room. The intake airflow was around 118 cfm, which is greater than the airflow suggested by ASHRAE for acceptable indoor air quality. INTRODUCTION Chronic overexposure to respirable silica dust (particle diameter < 10 microns) leads to a progressive lung disease known as silicosis. Workers who develop silicosis have an increased incidence of lung cancer and pulmonary disorders. In June 1997, the International Agency for Research on Cancer (1) found sufficient evidence to declare that inhaled crystalline silica in the form of quartz and cristobalite is carcinogenic. Mining is one of the leading industries for occupational exposure to silica dust (2-7). Control rooms located in dusty areas in some mines are of particular concern (8). Many mineral processing operations utilize operator’s compartments and/or control rooms to house workers who are performing particular job functions. Most industrial processing mills have rooms where a worker looks out over the facility and has direct control over the product flow throughout the entire building. In addition, primary crusher operators are often located in a compartment from which they are able to view the primary crushing function. Their job is to control when trucks dump into the primary jaw crusher and the rate of feed of the ore from the hopper into the crusher. Many of these control rooms and operator booths do not have filtration systems capable of cleaning air entering the control room or booth, which can result in elevated concentrations of dust in the room or booth. To reduce the dust concentrations in these rooms, it would make sense to clean the entering air with filtration/pressurization units similar to those proven to provide a clean environment in enclosed cabs."

Jan 1, 2016

Thermal pretreatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The effect of pretreatment using conventional and dielectric heating followed by quenching on the fracture properties of a number single and multiphase brittle materials has been investigated. The reduction in the impact fracture energies and particle strengths with and without pretreatment has been measured in precise single-particle experiments using the Ultrafast Load Cell. Variations in the fragmentation pattern caused by different pretreatments were assessed by measurements of the progeny size distributions. The differences in the effect of thermal treatment on single and multiphase materials are discussed based on the experimental results.

Jan 1, 1995

By S. A. Jeric

In-pit crushing and conveying of waste has been utilized in the mining industry for over 30 years. In recent years, innovations in crushing, conveying, and particularly waste and leach stacking technology have sparked a renewed interest in continuous haulage systems for large-scale open pit applications. A review of the advantages/disadvantages and operating techniques of crushers, feeders, conveyors, and stacking systems currently available is made. The paper examines some operations that are currently using large scale continuous haulage systems. Finally, a case study is presented that evaluates the application of a continuous waste haulage system in a large open pit mine in the Western United States, The case study includes a economic comparison with the existing truck haulage system.

Jan 1, 1997

By F. J. Sotillo

Mineral processing requires good classification of particles to attain an adequate separation of minerals. This is of utmost importance in the case of sulfide minerals. An ideal classification is obtained when particles are separated at a given mesh, which is fixed according to the characteristics of each sulfide ore. Under these ideal conditions, particles coarser than the mesh of separation are recovered in the underflow, whereas particles finer than the mesh of separation are recovered in the overflow. This paper presents the results of pilot plant tests that were performed on Ag-Pb-Zn and on Ag-Au Peruvian sulfide ores using a Density Separator, and the comparison of these results with those obtained using hydrocyclones, under similar operating conditions. The results show that the ratio of circulating load is reduced by 50% by using a Density Separator with respect to that obtained by using hydrocyclones. Moreover, the effect of the improvement in the separation efficiency obtained by using the Density Separator on the kinetics of flotation is also shown. Silver recovery of the Ag-Pb-Zn ore increased by 18% whereas gold grade in the concentrate of the Ag-Au ore is doubled.

Jan 1, 1998

By Rami Abousleiman, Gabriel Walton, Sankhaneel Sinha

"Although conventional coal mine designs are conservative regarding pillar strength, local failures such as roof-falls and pillar bursts still affect mine safety and operations. Previous studies have identified that discontinuous, layered roof materials have some self-supporting capacity. This research is a preliminary step towards understanding these mechanics in coal-measure rocks. Although others have considered broad conceptual models and simplified analogs for mine roof behavior, this study presents a unique numerical model that more completely represents in-situ roof conditions. The discrete element method (DEM) is utilized to conduct a parametric analysis considering a range of in-situ stress ratios, material properties, and joint networks to determine the parameters controlling the stability of single-entries modeled in two-dimensions. Model results are compared to empirical observations of roof-support effectiveness (ARBS) in the context of the coal mine roof rating (CMRR) system. Results such as immediate roof displacement, overall stability, and statistical relationships between model parameters and outcomes are presented herein. Potential practical applications of this line of research include: (1) roof-support optimization for a range of coal-measure rocks, (2) establishment of a relationship between roof stability and pillar stress, and (3) determination of which parameters are most critical to roof stability and therefore require concentrated evaluation.INTRODUCTIONRecent studies on pillar design have suggested that the assumptions utilized in traditional methods such as tributary area theory (TAT) (i.e. overburden has no self-supporting capacity, infinite pillar array, and CHILE material properties) are invalid in many geo-mining conditions (Esterhuizen, Mark, and Murphy, 2010; Frith and Reed, 2017). Although TAT is conservative with respect to pillar loading, and mine fatalities have steadily decreased since 1990, roof-falls and pillar bursts still occur and injure hundreds of miners per year (Mark, Pappas, and Barczak, 2011). Even though large-scale global mine failure has not occurred in a US coal mine since 2007, the mechanics of global and local stability as governed by the relationship between geologic parameters, mine geometry, and engineering design are still not well-constrained.Numerical methods are a highly effective tool that can be used to gain further insight into these relationships. When using such an approach, calibration to existing empirical relationships is imperative to ensure that numerical model results are realistic. In this study, we utilize the discrete element method (DEM) approach in Itasca’s Universal Distinct Element Code (UDEC v. 6.0) (Itasca, 2010).DEM accounts for explicit separation and contact of individual deformable blocks (Jing, 2003) and captures how discontinuities can affect system behavior. Discontinuous and anisotropic rockmass properties are typical features in coal-measure rock which contain various horizontal (bedding) and sub-vertical (joints) fractures depending on their depositional environment, diagenesis, and historic and current stress states."

Jan 1, 2019

By Basar Arioglu, Mustafa Tanriverdi, Seok Jae Seo

"INTRODUCTION Istanbul is a unique megalopolis connecting two continents. Population growth and economic development require permanent solutions and continuous investments on the transportation infrastructure. While the average population growth rate in Turkey is around 1.3% per annum, Istanbul is growing at an even faster rate of more than 1.5%. Even more striking is the fact that car ownership in Istanbul is increasing 5% a year, which is four times faster than the population growth. Although Istanbul Metropolitan Municipality (IMM) has worked persistently to improve the quantity and quality of the public transportation system in the city through, in particular, extending the available rail system network, the need for extra roads has always fallen behind demand. To make things worse, Istanbul is divided by the Bosphorus Strait, the large waterway connecting the Black Sea to the north and Marmara Sea to the south, which leads to the Mediterranean. This waterway is crossed via two suspension bridges, the Bosphorus Bridge built in 1973 and the Fatih Sultan Mehmet Bridge built in 1988. Current daily traffic across the bridges is around 450,000 vehicles per day. Ever increasing cross-Bosphorus traffic demands require other routes to be in place a soon as possible. While a third bridge farther north is currently under construction, yet another tunnel crossing is coming to the end of construction and is planned to be in service by December 2016. Being implemented under a Build-Operate-Transfer (BOT) model, Istanbul Strait Road Tunnel Project (ISRTP, the Project) has been under the spotlight not only because of its distinctive technical characteristics but also because of its robust business model, exacting financial and legal arrangements, diverse stakeholders and challenging organizational management structure. The following paragraphs offer an overall view of the Project from inception to where it stands now and extend to the imminent operational phase, touching lightly on all major aspects of this challenging journey."

Jan 1, 2016