Search Documents

By Hans von Michaelis

It is difficult to fail if one has a great deposit, but 'great' ore deposits are few and far between. More often one hears that a mine has been 'made' rather than found. This is particularly true for industrial minerals and for gold and silver projects. Even the best ore deposit can often be improved through innovative technology, e.g. the Escondida copper mine in Chile, where a novel ammonia leaching process is yielding a fabulous DCFROI. Consider the case of a small high grade gold mine. Previous owners had found inadequate reserves to justify the capital cost of developing the mine and installing a mill. Lower grade resources had been ignored because the owners were looking only for grades that would be high enough to support a small underground mine and mill. Randol, assisted by Kappes Cassiday & Associates, determined that the ore was amenable for heap leaching. Secondly, existing drillhole data indicated a significant lower grade resource that appears to be accessible to open pit mining methods. In this case, the appropriate selection of off-the­shelf technologies has literally 'made' the mine. At the Randol at Vancouver '94 conference on Latin American Mining Opportunities, papers on innovative technolo­gies for exploration, mining, metallurgy and environmental management were presented in non-technical terms for managers and resource developers. It was surprising how few of the exploration- and finance-oriented delegates participated in these sessions. Numerous technologies were presented that could be added to one's arsenal of tricks to 'make' a mine, i.e. to convert resources into ore reserves through knowledge.

Jan 1, 1995

By H. W. Gussmann, R. G. Rohrs, E. van der Merwe

Salinity in Effluents carries a high penalty as a result of toxic­ity, corrosion, limited re-use potential, scaling and environmental impact. Although the high TDS, such as Calcium sulfate, other than metals are still being dealt with a low key non issue basis, they are receiving more and more attention from regulators. Traditional solutions to solve these problems are costly and inefficient and create therefore severe constraints on the prof­itability of mining operations and out-price in general the finan­cial resources for environmental clean up operations. Going up the technology versus cost curve the most econom­ic solution to pollution is dilution but which is difficult in a coun­t1y shoti of water. If this can't be done, the second best, at least in sunny areas, is, to pump the whole effluent on a tailings dam for evaporation. Depending on the contaminants, one may have to pond the efflu­ent to avoid re-dissolution and seepage into the ground. The next most common solution to pollution is the addition of lime to remove and concentrate any dissolved metals and then dump the product, hidden in a mass of gypsum in a convenient place. Again ponding may be required to avoid ground pollution. However the treatment costs start to rise steeply if it is not allowed to discharge the limed overflow solution because of its high calcium sulphate content. Further treatment is then required in the form of high cost and high tech membrane process tech­nology such as reverse osmosis or dialysis or even mechanical driven evaporation.

Jan 1, 1998

By Robert A. Jankowski, J. Drew Potts

By implementing various mining practices, mine operators can reduce the respirable dust exposure levels of the roof bolter and the continuous miner operators. The Bureau of Mines has developed a computer program, entitled AMP (Alternative Mining Practices), that gives a quantitative comparison of these reductions. The alternative mining practices and their corresponding reductions in dust exposure levels that are evaluated by the program include a remote control continuous miner, a half-curtain ventilation system, two auxiliary fan-tubing bypass ventilation systems, a modified cutting sequence, a comparison between single-split and double-split ventilation networks, and a comparison between exhausting brattice and exhausting tubing. Descriptions of each of these mining practices are included in the report. The report also includes a hypothetical case study to show how AMP enables mine operators to select the technique(s) that is best suited to their particular needs. AMP is a compiled basic program that has been designed to run on computers with a DOS version 2.0 or later operating system. It includes high resolution graphics (640 X 200 dot positions) designed to run with video boards that are functionally compatible with the IBM Monochrome/ Printer Adapter. Graphic screens are selected from menus, and can be bypassed if the computer is not equipped to handle high resolution mode. Their primary function is to show proper implementation of the mining practices evaluated by the program. This package requires a minimum of 256K bytes of RAM. (Reference to specific products does not imply endorsement by the Bureau of Mines.)

Jan 1, 1987

By T. A. Griffin

Gentlemen: The subject of this paper is: ADVANCED APPLICATIONS OF BUCKET WHEEL EXCAVATORS AND RECLAIMERS. Against an urgent world wide energy crisis, the role of bucket wheel excavators and reclaimers in the surface mining of fossil fuels and other ores has been raised to new prominence. This paper will review the reasons for the expanded application of bucket wheel technology, its unique contributions, and other factors relative to volume, cost, versatility, and efficiency. Today, surface mining is faced with the twin challenge of (1), accelerating the rate of removal of massive quantities of overburden and ore, and (2), replacing comparable high volumes of overburden back into the mined-out portion of the pit. Optimum quantitites for - a single electrical power plant now range from 5 to 15 million tons of coal per year. The use of bucket wheels offers the best method for meeting this challenge at lowest possible cost. For example, an advanced application that also satisfies environmental concerns involves the simultaneous functioning of two bucket wheel excavators during surface mining operations. Working at spaced intervals and different levels in conjunction with a transfer conveyor and stacker, one excavator removes the ore while the other one transfers overburden to a stacker that replaces it back into the open pit. The result of this continuously operating cycle is: (1) removal of ore and replacement of overburden back into the pit in massive quantities, (2) at accelerated volume and extreme low cost that cannot be matched by conventional loading machines of any size, and (3) fulfills a basic environmental requirement which is to

Jan 1, 1974

By Henry P. Ehrlinger

These are exciting times for those of us involved in the discovery, development, beneficiation, sales and end uses of industrial minerals. The known sources of traditional raw materials are rapidly being consumed or covered up with highways and urban developments. We would never knowingly cover up a source of gold, silver, diamonds, or even base metals with a shopping center, but it has been difficult to justify not locating construction atop a limestone, granite, or sand dune deposit. During the last ten or so years most of the users of significant amounts of industrial minerals have established task forces made up of geologists, mining engineers, beneficiation experts, ceramic and refractory scientists, and senior members of their purchasing departments whose duty it is to determine where the raw materials for their particular finished products will come from now and farther down the road, like 20 years from now. Likewise, these same ceramic and refractory scientists are developing new materials which require a never ending change into different raw materials and the traditional materials must be refined by selective mining, exotic beneficiation practices and expensive but necessary post-beneficiation treatments to produce minerals for commercial use that were either theoretical minerals or at best showcase specimens when most of us here today were in school studiously acquiring a vocabulary which included Calcite, Magnesite, Dolomite , Feldspar, (Labradorite had the play of colors the prof could see but which I rarely focused on) Wollastonite, Celestite, Chromite, Olivine, Barite and Lepidolite to name a few.

Jan 1, 1976

By Vladimir Jindrich

This paper presents a history of a successful three year effort in locating a large, economic deposit of high purity limestone. The exploration program has been carried out by Ernest K. Lehmann & Associates, Inc., geological consultants, for Dravo Corporation, owner of the limestone property which is now under development. The permission of Mr. L. P. Struble, Jr, President of Dravo Lime Company, and Mr. M. W. Robinson, Director of Research and Development, to present this paper is gratefully acknowledged. The limestone property is on the Ohio River near Maysville in northern Kentucky, 60 miles east of Cincinnati (Fig. 1). The area lies at the eastern flank of the Cincinnati Arch, a regional structure where the Lower Paleozoic strata crop out below the adjacent younger sedimentary rocks of the Illinois and Apallachian basins. In general, the limestone formations of the Middle Ordovician High Bridge group offer the best potential for industrial limestone in Kentucky and adjacent parts of Ohio and Indiana. These formations are exposed along the axis of the Cincinnati Arch in central Kentucky. Toward the west, east and north, strata of the High Bridge group are progressively deeper, concealed beneath a succession of interbedded fossiliferous limestone and shale. The High Bridge group limestone formations are shallow-marine deposits largely of tidal flat, shallow lagoon and related environments. Principal lithologies include cryptocrystalline micritic limestone and crystalline dolomitic limestone to dolomite. Shale and bioclastic limestone are subordinate but the proportion of shale increases in the basal formations. Characteristic, is the occurrence of several thin beds of bentonite that serve as regional stratigraphic key horizons.

Jan 1, 1975

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION The two unit operations in cut-and-fill stoping that would benefit most from increased mechanization are drilling blastholes and moving broken ore to the ore¬passes. Drilling in current practice is done with hand¬held jackleg and stoper drills. Broken ore is commonly moved from the face to the orepass by a small slusher. This type of equipment can be easily moved through the raises. Hand-held drills have a slow drilling rate and require one operator for each machine. Drilling can be done much faster by small jumbo-mounted machines as two or more drills can be operated by one miner. Load-haul-dump (LHD) units move broken ore from the face to one or more orepasses at a much faster rate with less loss and dilution than slushers. These units are mobile and may be used at more than one place during a shift. The problem which must be overcome in applying this higher degree of mechanization is the restricted means of access inherent in current practices. Cut-and¬fill methods are usually applied to mining veins that are narrow, irregular in dip and strike, or where ground con¬ditions require the support of sand fill. The mechanized equipment which is needed to accomplish high produc¬tion cannot be raised or lowered through raises without being disassembled. A jumbo which will give the desired performance would be mounted on a rubber-tired carriage with a diesel engine for propulsion. Twin hydraulic booms run by a small air motor would carry pneumatic drills. Over¬all dimensions of the unit would be about 8 m (26 ft) in length, 1.6 m (5'/z ft) in width, and 1.6 m (5'/z ft) in height. An LHD of the desired capacity would be rubber¬tired and either diesel or electric-powered. The overall dimensions of a 2.3-m (3-cu yd) unit will be about 8 m (26 ft) in length, 1.8 m (6 ft) in width, and 1.5 m (5 ft) in height. It will weigh about 12 700 kg (28,000 1b). It can readily be seen that conventional raises can¬not handle this size equipment. The most desirable means of access enables equipment to be driven into the stoping areas. Ramps can enter the stope by being driven upward in the vein walls or by being developed in the vein on top of the fill as the stope advances. This ramp system not only permits the use of rubber-tired equipment in multiple working places but also enables its removal for repairs without component breakdown. In the proposed method, as in conventional cut-and¬fill stoping, sand fill will replace the mined-out ore. By constructing an inclined timber floor at one end of the stope, a ramp can be maintained on top of the fill and advanced as the stope is advanced cut by cut (Fig. 1). The ramp is, therefore, developed during the stoping process and is only driven as a tunnel when rising over and around the sill and crown pillars. A stoping section consists of three blocks of different geometric shapes. The first and last blocks to be mined will be triangular in the plane of the vein, and the blocks between will have the shape of parallelograms (Fig. 1). The first block will develop the initial ramp by breast stoping and filling to the ramp floor (Fig. 2). The ramp will need to be completed through to the next level be¬fore stoping of the subsequent block can begin. The subsequent blocks are mined by back stoping with the next ramp being developed at the other end of that block (Fig. 3). The length of each subsequent block can be varied without changing the slope of the ramp. As the new ramp is developed, the previous ramp is filled along with the stope cut. Access up and down is maintained through the stope. The final block is again breast stoped as no new ramp will be developed at the end line for jumbo egress. Boreholes provide ventilation between levels as well as utility access. They can also provide a secondary escapeway for personnel during periods of development. These boreholes would be located about 3 to 4.5 m (10 to 15 ft) in the footwall and spaced about 183 m (600 ft) apart along the vein. The orepasses are spaced about 61 m (200 ft) apart in the vein. This spacing allows not only a short tram for the LHD unit but also provides surge capacity for the ore between haulage trains. These passes are raised from the haulage levels. As development progresses, the raises are driven through the sill pillar, and then car¬ried in the fill as stoping progresses. Ventilation and utilities can be maintained through an orepass when it is not needed for ore. The end line orepasses are intended for this purpose as well as for personnel emergency egress. Overall dimensions and criteria assumed to illustrate the ramp method of access in a highly mechanized cut¬and-fill stope are: haulage level spacing of 61 m (200 ft); ramp gradient of 17%; average dip of approximately 1.57 rad (90°); initial stope length of 358 m (1177 ft); subsequent stope length of 179 m (588 ft); average stoping width of 3 m (10 ft) ; sill pillar thickness of 3.6 m (12 ft); crown pillar thickness of 1.8 m (6 ft); bored raises of 1.5-m (5-ft) diam; and cribbed orepasses of 1.2 x 1.2 m (4 x 4 ft) through the sill pillar and 1.2 m (4 ft) square inside the cribbed portion. DEVELOPMENT The ramp access system lends itself well to conduct¬ing the several phases of development concurrently. Haulage Drifts and Raises The first development step will be to drive the 3 x 3-m (10 x 10-ft) haulage drifts above and below

Jan 1, 1982

By Carolina Bruecker, Axel Preusse

"The topic of ground movements in Germany has been studied extensively in the past, especially in the field of active mines. The active hard coal mines were finally shut down in 2018 in Germany and lignite mining is expected to take place only until 2038. The so-called long-term liabilities of the mine operators in Germany include, among other things, the long-term guarantee of stability and thus the monitoring of ground motion.So far, the economic use of underground mining in Germany was mainly the supply of raw materials. In the future, the underground storage of compressed air, methane, or hydrogen will play an important role in renewable energy supply and climate change. Therefore, underground storage space will become more important and spatial planning is essential to ensure availability of safe underground openings for the various options of environmentally friendly energy storage.However, this renewed usage of underground openings may also bring new and sometimes unknown challenges of geomechanical influence. On the one hand, the aftermath of hard coal and lignite mining will be an increasing challenge in mining subsidence engineering. On the other hand, new possibilities due to underground spatial planning may lead to subsidence and/or heaving of the upper surface.INTRODUCTIONBoth hard coal and lignite have a long tradition in Germany. The Prosper Haniel mine in the Ruhr area was closed at the end of 2018 after 150 years, which signalled the end of hard coal production in Germany. Lignite mining still takes place in the Central German, Lausitz, and Rhineland districts. However, lignite mining in Germany is expected to be phased out gradually by 2038 (MDR, 2019). With the closure of these mines, however, mining damage is not over. The long-term consequences of mining, which extend far beyond the closure of the mines, are associated with the liability and responsibility of the individual mining companies. The so-called eternity burdens on the mining company continue to apply. In the field of lignite production, the discontinuation of dewatering and the resulting possible elevations of the surface will be a relevant topic for the future of mine surveying. The same applies to the hard coal mines, which are partially flooded in Germany and therefore require extensive monitoring of soil movements in the future.The discontinuation of energy from hard coal and lignite calls for a change in the energy mix. With the renewable energy revolution in Germany, the focus is on a sustainable and environmentally compatible climate and energy policy based on renewable energies. Sustainable use of the subsoil, both natural and anthropogenically produced cavities, will play an essential role in the objectives of this policy. For example, disused mine cavities can be used to store electricity from renewable energy sources. (Umwelt Bundesamt, 2018) These functions will again cause classical ground movements such as subsidence and uplift, but will also bring new challenges for the mine surveyor. Challenges can be underground cavity exploration in inaccessible areas or legal aspects of underground competition."

Jan 1, 2019

Slurry technology developed for the marine transport of mineral commodities has been increasingly applied to on-shore slurry transport systems. Reclaim of mineral concentrates, sand tailings for mine backfill and various industrial minerals from storage tanks or ponds normally require a slurry of high density at constant flow rates to improve process performance and to reduce handling costs. An efficient system must accomplish this at minimum capital costs with maximum reliability. Continuing improvements in equipment design to improve repulping efficiency and their application are discussed.

Jan 1, 1986

Mining at Hudson Bay Mining & Smelting's (H. B. M. & S.) Snow Lake Division is now in the mature stage of the mines lives. These base metal copper-zinc mines have been operating for over 30 years. Stopes had small pillars called "crown pillars", left between them. These pillars range up to 100 meters long by 40 meters wide and 15 meters thick. H. B. M. & S. has been successful in removing these pillars through the use of cable slings, electric scoops, longhole mining and diesel LHD equipment. The different shapes and sizes of these pillars has meant that many innovative techniques have been tried in order to find acceptable economic mining methods. An overview of the different methods will be outlined.

Jan 1, 1992

By Heinz Hofmann

In order to drive tunnels with low overburden in town regions, it is necessary to give a quantitative prognosis for the deformation of the underground as well as of the tunnel-lining and of its stability. These problems and their solutions are illustrated by the works for a two-track-railway-tunnel in Bochum (Ruhrdistrict). In this case the most important problems consisted in passing below buildings in a vertical distance to the fundamentals of only 3.20 m and a railway earthdam with rapid train traffic in a distance of 4 m under the dam. The results of measurements from other comparable tunnels and finite-element-computations were used to prognose the settlements on the surface and in the ground, their distributions and their development in time. To obtain these values at the site, a special system of tunnel driving was executed. The tunnel was excavated with the newest type of tunneling-machine from DEMAG, cutting an inclined front, immediately followed by a special temporary support of shotcrete and inclined steel-ribs. By using theoretical and empirical methods to assess the behavior of the tunnel and underground and by executing an optimal driving system in technical as well as economical aspects, the expected behavior, expressed in quantitative values, was almost equivalent to those received by control measurements.

Jan 1, 1974

By Maurice Deul

Certain health and safety hazards occur entirely unexpectedly in some subterranean excavations. Although ground support is not the subject of this paper, ground failure can result in large and often uncontrolled flow of fluids into an excavation. Even when there is no ground failure, the disturbance of nature's equilibrium between rock or unconsolidated alluvium or rubble and the contained fluids poses severe problems to a well planned operation. Optimum conditions for safe operation cannot be the sole criterion for site selection. Some mineral deposits form in zones of structural weakness, others form where hydrothermal alteration substantially weakens the enclosing rock, and tabular deposits such as coal and evaporites inevitably undermine large areas. Excavation to acquire mineral values cannot be relocated. The same is often true for tunnels driven to connect distant points by the most direct route. Rivers and mountains cannot he avoided, and the cost of lengthening a tunnel--by even a fraction of a percent--must be strongly justified. No responsible engineer will knowingly select a dangerous route for excavation, but to what extent do engineers attempt to assess the health and safety hazards that may be reasonably expected? How, specifically, can methane explosions, water and sand flooding, dangerous dusts, toxic gases, thermal shock and radar poisoning be eliminated or minimized through systematic advance planning?

Jan 1, 1974

By M. Cambridge

The design process must anticipate all construction and operational conditions and make an allowance for all eventualities. Prevention of failure during operational life, and in some cases post abandonment, requires that a risk assessment is undertaken during the design stage which defines not only the factors of safety to be used but the criteria for the structure during its operating life. These operating criteria should clearly identify the at-risk structures and the inspection and monitoring routines required to ensure compliance with the design objectives. On a mine site, it is the role of mine management to ensure that the operating rules be applied throughout the mine life and that a system of inspection and monitoring procedures be instigated. Where the risks are significant, high-level auditing by an independent engineer will also be required. Within the inspection and auditing framework, the designer needs to incorporate instrumentation to enable the operators and management to confirm that the facility meets the requirements of safety, stability and environmental compliance whilst continuing to meet its operational function. This paper reviews the use of inspection and monitoring to prevent failure and provides, in summary, examples of where monitoring has been undertaken and prevented failure. A tabulated review of legislation, regulations and technical guidance generated as a result of previous failures or untoward events is provided.

Jan 1, 2005

By David J. Herzog

There are two steps in evaluating potential mine waste impacts on ground and surface waters. Characterize the mine waste (characterization methodologies) and assess potential impacts (assessment strategies). One or both may be required for mine permitting, operation and closure. The first step is to characterize the waste. Determine if it has the potential to release chemical constituents or acid rock drainage to the environment. If no potential exists for release to the environment, the evaluation process is complete. A monitoring plan is then established. If the potential exists for release of chemical constituents or acid rock drainage to the environment, a strategy to evaluate potential impacts must be implemented. Strategies discussed here to evaluate potential impacts were developed during investigations at precious metal and base metal mines in Nevada. Water resources in Nevada consist mostly of ground water. So the strategies discussed focus on potential impacts to ground water. However, several of these strategies also apply to assessing potential impacts to surface water. Implementing these strategies has helped determine the potential for impact and has been successful in permitting mine expansion as well as allowing continued operation and obtaining mine closure at several mine sites in Nevada. These strategies were carried out in accordance with Nevada Division of Environmental Protection (NDEP) regulations and through the National Environmental Policy Act (NEPA)

Jan 1, 1995

By J. W. C. Wong, S. D. Miller, J. J. Jeffery

Pre-mining identification of acid forming mine and waste materials is of concern to the mining industry because of the potential for the generation of acid mine drainage, acid rock drainage, and soil acidity problems. Accurate identification of acid forming material is essential for developing appropriate waste management strategies to reduce environmental problems related to acid generation from sulphide containing wastes. The acid-base accounting procedure, in its various forms , is commonly used for pre-mining screening of mine and mine waste materials. The procedure is generally effective when used and applied correctly but is prone to incorrect interpretation of results which can have significant financial and environmental implications. This paper examines the acid-base accounting Procedure and the possibility of misuse of this method with special emphasis on the sampling method, the sulphide forms, the acid neutralization capacity, and the interpretation of results. Data from numerous coal, base metal, and gold mining operations are used to illustrate the application of the acid-base account. The data base indicates that overall, approximately 1/3 of all waste generated by mining and mineral processing is potentially acid forming indicating the need for correct identification and management. Problems associated with simple application of 'absolute' acid-base criteria for classifying acid forming material are highlighted and the need for developing site specific or 'relative' criteria is discussed and illustrated by case study.

Jan 1, 1991

By Michael Drozd

The operation of an activated charcoal system has five separate unit operations. These unit operations have common points for CIP, CIL and CIS system, which vary widely in application. a. Absorption b. Desorption (Stripping) c. Acid Washing d. Reactivation e. Carbon Handling ( carbon transportation, sizing, de­watering, etc.) Cost optimization starts with the basic operating parameters (design philosophy) set down at the time of engineering design. This parameters undergo almost immediate change due to site specific ore requirements, throughput changes, operator requirements or reagent availability. Activated charcoal is sometimes viewed as simple, uncomplicated reagent that requires not optimization. To some extent, this statement is true, but under most circumstances, if the time necessary to optimize the use of activated charcoal is available, the effort is rewarded with significant savings. CPL-Carbon Link has embarked upon a program of supplying technical support with its activated charcoal. Several operation in the United States have under taken to have CPL-Carbon Link do an operational survey to determine if potential savings are possible. CPL-Carbon Link has offered to do these surveys for projects that are clients or simply would like to have CPL-Carbon Link review their operation. The information accumulated by CPL-Carbon Link is being used to attempt to fashion industry standards so that a common reference point came be establish for activated charcoal usage.

Jan 1, 2000

By Jeffrey P. Chanton

A specialized Pore-Fluid Array sampler (PFA) was designed to collect and store pore-fluids to monitor temporal changes of ions and gases in gas hydrate bearing sediments. We tested the hypothesis that pore-fluid chemistry records hydrate formation or decomposition events and reflects local seismic activity. The PFA is a seafloor probe that consists of an interchangeable instrument package that houses OsmoSamplers, long-term pore-fluid samplers; a specialized low-dead volume fluid coupler; and eight sample ports along a 10-meter sediment probe shaft. The PFA was deployed at Mississippi Canyon 118, a Gulf of Mexico hydrate site. A 160-day record was acquired from the overlying water (OLW) and 1.3 meters below seafloor (mbsf). Fluids were measured for dissolved chloride, sulfate, and methane concentrations and dissolved inorganic carbon and methane stable carbon and deuterium isotope ratios. Chloride and sulfate did not change significantly over time, suggesting the absence of gas hydrate formation or decomposition events. Over the temporal record, methane concentrations averaged 4 mM at 1.3 mbsf and was thermogenic in origin (d13C-CH4 = -32.4±3.4?). The timing of an anomalous 14 mM methane spike coincided with a nearby earthquake (Mw=5.8), consistent with the hypothesis that pore-fluid chemistry reflects seismic events. Keywords: Osmosampler, gas hydrate, methane, stable isotopes

Jan 1, 2008

By Gary S. Brierley, Tracy J. Lyman

INTRODUCTION Geotechnical engineers play a major role in tunnel design primarily because tunnels are constructed entirely within the ground. In general, this role can be divided into two major tasks: subsurface investigations and project design. Under subsurface investigations, it is necessary for the geotechnical engineer to accurately describe the ground in which the project will be built. Under project design, it is necessary for the geotechnical engineer to work together with other members of the design team to make certain that the tunnel fulfills its intended purpose at least cost. Given in the paper are the authors' opinions about what constitutes an adequate scope of services for these two tasks on a tunneling project. SUBSURFACE INVESTIGATIONS o Background Study All subsurface exploration programs for tunnels begin with a thorough investigation of background information about the proposed site. Such background information includes geologic, reports topographic maps, aerial photography, and case history reports of other nearby tunnels. Once completed, it is necessary to study the background information so that the proper scope and magnitude of subsurface exploration work is performed in a manner that provides maximum input to a knowledge of those intact and rock mass properties that are important for an understanding of the entire ground mass. The blind application of field and laboratory techniques, no matter how sophisticated, is wasteful and potentially

Jan 1, 1989

By John Wiebmer

Six industry trends will have significant effect on the way mining equipment is designed and supported in the years ahead: 1. MINING IS MIGRATING TO LESSER DEVELOPED PARTS OF THE WORLD The global recession of the early 1980's drove down commodity prices and intensified cost competition. This caused a fairly dramatic trend in mining away from higher cost operations in developed countries to richer, lower cost deposits in developing countries. Miners operating in lesser developed parts of the world will place higher value on rugged, durable designs that can live in more difficult and sometimes abusive conditions. They need engines and power train systems that are more tolerant of a wide variation in fuel quality and oil specifications. They'll require machines that are simpler to operate, simpler to maintain, simpler to troubleshoot and simpler to repair. And they'll require creative means of support in getting technical information, parts and components to remote operational sites. Mining equipment in the future will be more durable and simple than it is today, and product support will grow in importance as purchasing criterion. 2. THE MINING INDUSTRY IS CONSOLIDATING An intense amount of corporate acquisition and industry consolidation activity is occurring, to the point that today just 50 mining companies account for 55% of the western world non-fuel mineral production. Consolidation will continue, leading in the future to an industry structure weighted heavily toward a few key global mining houses.

Jan 1, 1993

By R. J. Reuss

Mina Maria is a high-grade, underground copper mine located in the Cananea district of Sonora, Mexico. The ore body is a massive sulfide breccia located in mountainous terrain. A major highway and an electric transmission line pass directly over the near-surface ore body. The mine is operated by Minera Maria SA de CV, a joint venture company that is 51 % owned by Empresas Frisco SA de CV and 49% by Cominco Resources International Ltd. Empresas Frisco is the operating partner. Production began in October 1990. The mining method used is undercut and fill. A continuous miner and a single-boom, hydraulic jumbo mine the ore. Backfill is a weakly cemented sand-gravel mixture that is pneumatically placed. The ore is treated by conventional crushing, milling and flotation. The Maria deposit is located about 40 km (25 miles) south of the Sonora-Arizona border and 11km (7 miles) northwest the city of Cananea and the Cananea Mine. The mine portal, at an elevation of 1780m (5840 ft), is on the east side of an important drainage divide. The mill site is situated about 800 m (2625 ft) northwest of the mine on the northwest side of the drainage divide where the drainage is more favorable. Its elevation is 1860 m (6100 ft) (Fig. 1).

Jan 1, 1992