Search Documents

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

In spite of our deep conviction that it would be wrong for the United States to enter World War II, when, after Pearl Harbor, we were actually in it, I felt that I must do all I could to help. The country had been so good to me that I could not decently stay on the sidelines. My first thought was that I might help with supply and administration in the Air Force, as in World War I. So on the evening of Pearl Harbor I wired the chief of our Air Force in Washington saying that I had been on Gen. William Mitchell's staff in World War I and was offering my services again. I received a noncommital answer, but after a couple of weeks was told to take my physical examination. I passed it, but nothing further happened. After helping to make plans for the wartime operations of Summit King and Desert Silver, Dorothy and I went to New York to spend Christmas with Molly and Peter, both of whom were in college in the East. I had to complete a report on the Argonaut mine in California first, though the war made my recommendations of dubious validity. Before Christmas I received wires from Temple Bridgeman, Phil Wilson, and other friends who had taken positions with government agencies responsible for securing mineral products needed for war use. They urged me to join them. It was evidently a case of not whether but how I could be most useful. After six uncertain days with the family in New York I took the night train to Washington on the 28th of December. I had a hectic day there. First I saw Arthur Bunker and Phil Wilson at what became the Aluminum and Magnesium Division of the War Production Board. Their office was in an old converted barracks. They asked me to examine magnesium deposits in Nevada at once, and then to look at other magnesium and aluminum properties. After leaving

Jan 1, 1976

By J. Herbst, A. J. Lynch, E. V. Manlapig, G. C. Throne, J. S. Hall, G. Poling

Modelling of industrial sulphide flotation based on data collected in several flotation plants is discussed. A mechanistic approach is used in which it is recognised that flotation is a two stage process with concentration occurring both in the pulp and in the froth. The important features of the model, which is a kinetic model, are – 1. for each particle species there is a range of flotation rates which corresponds to the range of particle sizes, 2. the flotation rates of the liberated gangue particles which have no hydrophobic properties are dependent on the flotation rate of water and are controlled by variables such as the air and frother addition rates, and the pulp level, 3. as an approximation the valuable sulphide particles may be regarded as being present in two groups with high and low flotation rate constants, 4. increase in the addition rate of collector tends to increase the proportion of sulphide particles which are in the high flotation rate constant group. The actual flotation rate of each group of particles is a combination of an "inherent" flotation rate and a flotation rate which is dependent on the flotation rate of water, at particular air and frother addition rates and pulp levels there is a physical limit to the rate at which particles can be transported into the concentrate and this is recognised in the

Jan 1, 1976

By A. W. Mitchell

Mining of a bedded barite deposit exposed highly pyritic siliceous sediments which have weathered and degraded subsurface and surface waters. The ph, sulfate, and total dissolved solids are the most seriously affected parameters. Several solutions were tried and eventually horizontal holes were drilled into the mine wall to draw down the water table and decrease the movement of groundwater through oxidizing zones opened up by the mining operation. Areas of surface disturbance were capped with layers of soil, bentonite, and gravel to decrease the infiltration of water into the disturbed areas. These actions have begun to decrease sulfate and total dissolved solids concentrations and increase ph values.

Jan 1, 1987

By Jan Van Greunen, Mark Vanderzee, David Haug, Geoffrey Hughes, Yiming Sun, Roozbeh Geraili Mikola

"The Sanitation Districts of Los Angeles County is planning to construct a new, approximately 7-mile-long (11.3 km) effluent outfall tunnel to be excavated by TBM and lined with precast concrete segments. Anticipated net operating pressures within the tunnel are expected to approach 3 bar. To counteract joint opening and exfiltration leakage, an approach has been investigated to post-tension the precast concrete tunnel lining with steel tendons. The tunnel alignment crosses several seismically active fault zones, at which installation of steel pipe is proposed as a secondary inner lining to mitigate potential offset displacements. This paper discusses the tunnel lining design approach and methods used to address these unique challenges.INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) is planning to construct a new 18-foot-diameter (5.5 m), approximately 7-mile-long (11.3 km) tunnel from the Joint Water Pollution Control Plant (JWPCP), located in the City of Carson, to the existing White Point outfall manifold structure at Royal Palms State Beach (RPSB) (Figure 1). The project is part of the Sanitation Districts’ Clearwater Program, which will improve overall system reliability through the repair and replacement of the existing aging infrastructure. The existing system includes two 6-mile-long (9.7 km) tunnels, 8- and 12-feet in diameter (2.4 and 3.7 m), and four ocean outfall pipes with a maximum capacity of approximately 675 million gal/day (MGD) (2.6 billion L/day). Addition of the new parallel tunnel will increase overall capacity to accommodate peak wet weather wastewater flows of up to 1,262 MGD (4.8 billion L/day) and will allow inspection and repair of the existing tunnels. The new outfall tunnel will be excavated using a pressurized face tunnel boring machine (TBM). Shafts at the north (JWPCP Shaft) and south (RPSB Shaft) ends of the proposed alignment will connect the tunnel to the existing wastewater treatment plant and existing ocean outfalls manifold and during construction act as launch and receiving shafts for the TBM. The tunnel will be excavated from north to south as a single heading."

Jan 1, 2016

By G. W. Kenzy

Recently, in the United States, questions of possible deleterious synergistic health effects of the gaseous and particulate components in the diesel exhaust and mineral and coal dust have been the impetus for extensive research by several agencies. At the present time, diesel engines are tested and approved for use in gassy and non-gassy underground metal and non-metal mines under Parts 31, 32, and 36 of Title30 of the Code of Federal Regulations. Diesel-powered equipment for use in underground coal mines, though not explicitly addressed in the law, is administered under Parts 32 and 36 of Title 30, with Part 36 being applied in the case of equipment working inby the last open crosscut or in the return airways. Operation of diesel equipment in underground mines has the potential for serious health and safety hazards from the gases, vapors, and particulates in the exhaust. Therefore, various countries have rules and regulations for the safe deployment of diesel equipment. The applicable laws and regulations from several countries who have long experience with diesel-powered equipment in their mines are reviewed. Four major areas have been addressed: (1) testing and approval procedures of diesel engines, (2) ambient mine air quality specifications, (3) frequency of sampling and location of samples, and (4) air quality specifications in splits where diesel-powered equipment are operated. The review indicates that most regulations generally consider four possible hazards: (1) toxic components in the engine exhaust, (2) ignition of flammable atmospheres by the engine or electrical equipment, (3) fire hazards presented by the engine fuel oil and by combustible material that might come in contact with the equipment, and (4) mechanical hazards. There is a remarkable similarity in the laws with regard to engine design, testing and approval procedures. However, the aspects with regard to mine air quality and quantity are quite variable-- from a general statement to very specific standards for many different diesel exhaust constituents. However, the laws with regard to synergistic effects of diesel exhaust components and other mine air contaminants are an exception.

Jan 1, 1980

By David Runnels

In September 1970, the Quebec Cartier Mining Company, started development of the Mount; Fright iron ore mine. The estimated ore reserve is in excess of 1,000,000,000 long tons with an average grade of 31.5% Fe. The run of mine ore is crushed, ground and concentrated to a product having 66% Fe and 5% silica at an annual concentrate production rate of 18.4 million long tons. The daily production rate of over 50,000 long tons of concentrate necessitates a daily mine output of approximately 250,000 long tons of material of which 50% is waste. The mine is located in the Province of Quebec, close to the Labrador border approximately 600 miles north-east of Montreal. The development of the mine necessitated the construction of an all electric one thousand housing unit townsite along with associated services such as a shopping center, swimming pool, arena, school, etc... A one-hundred mile long, 315 K.V. Dower line was built between the mine site and the Hydro-Quebec 735 K.V. existing power line between Churchill Falls and the Montreal area. The construction near the mine of a beneficiation plant was necessary to upgrade the 31.5% iron ore to a marketable product of 66% iron.

Jan 1, 1977

By Joseph B. Smith

I work as the Bureau's Liaison Officer for Colorado and am one of 38 Bureau employees who are stationed, for the most part, in state capitals across the nation. These offices serve all 50 states and Puerto Rico--some being assigned more than one state. Our primary task is to seek ways to achieve a closer and more productive relationship between State agencies and the Bureau of Mines. In 1970, when the Bureau initiated this nationwide system, our activities were limited to mineral supply operations. The potential of the program was soon recognized and Liaison Officers became the personal representatives of the Director and responsible for con- ducting the business of the Bureau that is best handled at the local level. Knowledgeable in the total operations of the Bureau, Liaison Officers are a primary point of contact for the public and for you to obtain information and, again, for you to provide the government with insight into the difficulties you have in providing this nation with an adequate supply of industrial mineral materials.

Jan 1, 1975

By Michael Gauna

A high seam geologic condition exists at Jim Walter Resources No.4 mine which requires immediate rib support after a continuous miner cuts a place, High seam mining heights are typically 2.4 to 2.6 m (8 to 9 it) and a thick rock layer is present in the upper portion of the coal rib side. The 610 m (2000 ft) mining depth at No. 4 mine induces horizontal rib line movement after excavating an entry. Horizontal rib movement greater than 30.5 cm (12 in) have been noted. When lateral movement occurs in the high seam areas, the thick rock layer, and the coal above the rock layer, become fractured and tend to roll into the entry. If not adequately supported, large rib rolls develop in the place being bolted as well as in previously mined areas which endanger men and equipment. To control this situation rib support must be installed in the roof bolting operation as the bolting crew works towards the face. A rib control system has been developed for this high seam mining condition utilizing a mechanical anchor bolt placed at an angle in the rib and installed with a modified Fletcher DDFI- 15 bolting machine. Over 120 km (75 mi) of entry have been supported with angle rib bolts. These angle bolts constitute 43 to 60% of the total roof and rib bolt footage in the high seam port- ions of No.4 mine. The angle rib bolting system has proven safer, more effective, and more efficient than the earlier support method employing bolts installed horizontally into the rib. No rib roll accidents have occurred since the angle drill bolting machines were placed in service in 1981. By securing the broken rib material with an angle bolt anchored above the coal pillar, a more effective means of rib control is achieved. Angle rib bolting does not interfere with continuous miner productivity. In addition, bolting crews are now reduced from three to two people and the total drilling supply costs are approximately 60% the previous cost, when compared to the previous support method using horizontal rib bolts.

Jan 1, 1983

By A. S. C. Owili-eger

An efficient state-of-the-art dynamic model to simulate and predict the rate of water production in longwall coal mining operations was developed as a tool for mine planning purposes. The model can also provide an estimate of any potential resultant hydrogeological impacts of an operation via an array of element-specific single-valued parameters referred to as the field rating indices. The computational procedure was designed to fully exploit the benefits of hydrogeotechnology and utilize a combination of conceptual, physical, empirical, and numerical approaches to define, characterize, analyze, and evaluate flow con- trolling properties of fractured rock systems. The model presented here provides a dynamic prediction method for highly fractured flow; a practical tool in mine and water control planning; and a cost-effective means of assessing, based on the best available technology, the impacts of mining on the water resources within a mining environment to satisfy local and federal regulatory requirements. Unique features include consideration of laminar and non-darcian flow domains in double-porosity-pressure hydrogeological media.

Jan 1, 1987

By H. Kempton

New methods for remediating metals-contaminated groundwater include in-situ emplacement of highly adsorptive substrates to permanently retard solutes. Substrates are introduced by sequential injection of soluble components that precipitate in the aquifer, forming a permanent high-retardation zone. This method overcomes the factors that limit pump-and-treat remediation; i.e, long-term source loading and slow desorption. Column tests demonstrated efficient substrate emplacement, increasing retardation coefficients of Cr(VI) by 20 and As(V) by 40. Similar effectiveness is expected for other heavy metals. Simulations using a coupled advective-geochemical model accurately matched substrate emplacement and arsenic attenuation, allowing extrapolation to other constituents and larger-scale applications.

Jan 1, 1999

By A. H. Summers

The La Choya mine is located 55 km south of Sonoyta in northwestern Sonora, Mexico. Mineralization is controlled by a 40 meter thick thrust fault zone which created a permeable host for the metal-bearing hydrothermal solutions. The ore body is mined by open pit using wheel loaders and truck haulage. Gold and silver are recovered from low grade ore by heap leaching followed by carbon adsorption.

Jan 1, 1997

By Paul Richardson

This paper discusses the drilling techniques and equipment used by Loffland Brothers Company to drill the AEC's UC-3 large diameter shaft in Nevada. Included are pictures and illustrations of the drilling-mud circulating system, the surface and downhole drill-string and the special heavy-duty mast and hoisting equipment required to do the job. The purpose and method of lining the large diameter holes along with the technique and materials used to backfill the lining to hole annulus are discussed briefly. Areas requiring improvement in both equipment design and technology for large diameter shaft drilling are discussed briefly. Shafts as large as 140 inches in diameter to depths of 5,000 feet can be drilled with existing equipment and technology.

Jan 1, 1969

By S. Rupprecht

"INTRODUCTION This paper addresses the prevalence of poor public reporting practices of Coal Exploration Results, Coal Resources and Coal Reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or “saleable” tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal – therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (“ROM”) and Saleable coal tonnage, their associated qualities and other material and relevant information. Competent or Qualified Persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provide. “Companies are encouraged to provide information in their Public Reports, which is as comprehensive as possible” (CRIRSCO, 2013): too often this isn’t the case and material matters are either not reported or inadequately disclosed. According to the South African National Standard (SANS) 10320:2014 draft document - “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw Saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the Saleable Coal Reserve must be stated. The moisture basis of reporting shall be stated.” As an example to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are highlighted. The Kendal power station, commissioned in 1988, operates at a Calorific Value (“CV”) range of 19 to 20MJ/kg, an Ash content between 29 and 34% and Volatiles between 20 to 21%. Other power stations, such as Kriel or Hendrina, may require different qualities such as a CV range of 22 to 23MJ/kg, an Ash content between 20 and 28% and Volatiles between 22 to 23%. Thus, in terms of domestic saleable coal, it isn’t just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station” (Chetty, 2010). Sulphur content is also another important quality with the ideal coal content having a quality of less than 1% Sulphur."

Jan 1, 2018

By L. E. Mylting

Modern ash handling systems exist in considerable numbers and a great deal of design and operating experience has been accumulated, It is the endeavor of this paper to point to a number of frequently recurring problems, A general appreciation of these problems will be helpful in both design and operation of systems. The light fly ash and the heavy bottom ash present different problems, and each will therefore be treated separately. Fly ash is collected in the ducting from the furnace to the stack and beneath the mechanical and electrostatic dust collectors. The greatest amount of dust is collected beneath the mechanicals and electrostatics. Hoppers are generally provided as integral parts of the collector. Suitable valves and piping are connected to these hoppers for removal of the dust. The size and shape of these hoppers are important factors in determining frequency of handling and the capacity of the system.

Jan 1, 1958

By Brian Mangogna, Clay McNail, Weishi Mang, Adam Steimel

Together with innovatively applying modern flotation reagents and developing the breakthrough mill enterprise expert control and operating system, Doe Run Buick Mill constructed an advanced large copper rougher scavenger to process its complex Pb\Zn\Cu ore more efficiently. The scavenger circuit, featuring its own motor control center, air blower, multiple reagent loops and FrothSense+™ camera, operates both mechanically and chemically to maximize copper recovery and under expert control. Such scavenger features can be applied to zinc rougher circuits for all Doe Run mills to maximize Cu recovery during Cu special runs when the zinc rougher becomes a copper rougher scavenger.

Feb 1, 2025

By G. A. Gunderson

Since our time is very limited, I would like to relate to you as best as I can a few important areas that I think may be helpful. 1.) The Real Difference between Dense Phase and Dilute Phase Pneumatic Conveying: Within the many variations of so called Dense Phase conveying, it is often difficult to determine to what degree a system is Dense Phase or if, in fact, it is a Dense Phase system at all. A system that appears and is generally known to be Dense Phase can under certain operating conditions perform as a Dilute Phase system. If, for instance, a high pressure system, which is generally a Dense Phase system, operates at 60 PSIG, say 4 atmospheres, utilizes enough air volume, the conveying velocity will easily exceed the normal design velocity of a typical Dilute Phase system. Now, on the other hand, a low pressure system which we will term a Dilute Phase system, operating at 15 PSIG; say 1 atmosphere, can convey a given product at well below the saltation velocity, like a Dense Phase system.

Jan 1, 1977

By Henry T. Mulryan

The philosophy, strategy and techniques of successful marketing of talc, differ sharply from those applied to most other mined products. Unlike non-ferrous metals, there are no commodity exchanges to facilitate the transfer of goods. Unlike iron ore and some non-metallics, assured markets by means of long term contracts are practically non-existent. Talc must be sold and sold and sold again. The normal channels of talc distribution are almost identical to those used, by the chemical industry. These consist of a blend of producer marketing staff, field technical service, and sales force; and independent chemical wholesalers. Like the term "chemicals", there is tremendous product diversity contained in the rather loose expression "commercial talc". Certain kinds of talc, processed in conventional ways, are regarded as commodities by the consumer. That is, that material from one source or supplier is considered to be effectively interchangeable with those available from a number of other areas and producers. Under such conditions, lowest delivered price, quickest delivery, and best, customer service, are the key factors in a successful sales effort.

Jan 1, 1965

By Pierre Dosmond

In ore mining technology, the loading and hauling operations are undoubtedly the area where the most spectacular progress has been made during the last twenty years. I shall draw some examples from the Eastern France iron ore mines which I how well and whose production of 62 million tons for 1962 and 1963 constitute a worthwhile experience worldwide. The iron ore deposits of Lorraine are of sedimentary origin. They contain many mineralized horizons with workable seams situated from 330 to 830 ft. in depth. The dip of these seams is generally less than six percent. Their thickness varies from 6 to 23 ft. All seams are not workable throughout the whole area of occurrence, but in some mines there are five mineable seams in the same vertical section, with from 5 to 20 ft. of barren ground intervening between them. The iron content of the mineral varies from 28 to 36 percent. Specific gravity of the ore is 156 lb. per cu. ft. m place and 100 lb. per cu. ft. blasted. Reserves of iron ore in the Lorraine region are estimated at six billion tons with an iron content of more than 28 percent. These mines operate by means of rooms and pillars process, with pillar robbing; the final recovery is very good and averages 90 percent. Some years back, competition from richer, imported ores incited these mines to make constant efforts to increase their productivity and reduce mining costs, thus placing them in a leading position in mining technology, as evidenced by the dramatic evolution of their output per manshift (Figure No. 1).

Jan 1, 1970

By Ralph M. Stricklen

The need to move large tonnages of slurry has grown as mines have become larger. As existing tailing depositories are filled up, new mines developed, or environmental requirements dictate, it becomes necessary to transport tailing particularly over longer distances. A typical slurry transport system is shown in Figure 1A. Figures 1B, 1C and 1D show sketches of the system auxilliary components: feed box, receiving sump and drop box, respectively. There are two basic types of slurry transport systems, packed flow and slack flow. Packed flow is typified by a pipe running full; slack flow by a launder or pipe running less than full. Slack flow in launders or channels is also referred to as open channel flow. Generally slack flow slurry transportation involves a flow with less than 65 per cent solids, and there is an upper limit on particle size, depending on the slope of the system.

Jan 1, 1984