Search Documents

By Raymond F. Moran

The history and development of the FMC Coke process has been reported in numerous presentations over the past 10 years (1, 2, 3, 4, 5, 6) but a short review is desirable, especially regarding the aspects that are influenced by the coal to be used. F'MC has been developing this process in pilot facilities since 1956 and in a modest sized plant in Kemmerer, Wyoming since 1960 (Figure I). This plant produces strong uniformly sized coke briquettes from a completely non-coking coal, namely Elkol, a sub-bituminous coal of the Adaville seam. Since operating commercially, over 300,000 tons have been produced, 90% of which has been used in electric phosphorus furnaces and some 10% of which went for trials in iron blast furnaces. We believe that this commercial use of non-coking coals is a unique experience in the history of coke manufacture.

Jan 1, 1975

By P. J. Bethell

In the froth flotation process the detrimental effect of slimes on the froth flotability of valuable minerals has long been known.1 Work by Aplan2 on the froth flotation of coal has shown that the presence of clay slimes causes loss in flotation selectivity, and recovery of combustibles. Obviously then the presence of clay slimes to any great extent in the froth cell feed in a coal preparation plant is undesirable. This problem is exacerbated in plants treating raw 600 um (28#) by zero material due to the variation in flotation with size. The net effect of this phenomenon in a bank of cells treating raw minus 600 µm (28#) material s that by the time adequate flotation of the coarsest size fractions has occurred the finer sizes are already producing undesirable high ash material, which often leads to unacceptable overall quality. Reduction in aeration rate and/or chemical addition to combat this, further decreases the flotation rate of the coarsest fraction leading to heavy losses of coarse low ash coal to the tailings. The above mentioned characteristics formed a key aspect of the fine coal circuitry design at Elk Run Coal Company in Sylvester, WV. The plant was designed to produce compliance steam coal (less than 1.20 lbs. S02/million b.t.u.) Desliming ahead of the froth flotation was included, as the slimes in the plant feed were clay rich, had very high ash levels, and low potential recovery. Lab testwork had also shown that poor selectivity would be expected if raw minus 600 um (28#) material was froth floated.

Jan 1, 1986

By Richard Emberley, Timothy Shaw, José L. Torero, Jurij Karlovsek, Timothy Gibson

"Tunnel closures are highly undesirable and the lengthiest are generally attributed to structural failures (e.g. Mont Blanc). Although historical data shows structural failures are closely linked to fire, design parameters for tunnel safety are not well defined. Current research has focused on defining the fire heat release rate and temperature, but these parameters cannot be easily used to determined structural performance. The energy transferred to the structure, the heat flux, is required but current literature lacks these values. Full scale experiments were undertaken on passenger vehicles resulting in heat fluxes between 20-70kW/m2. Analysis shows a vehicle fire’s duration is closely linked to its mass. Further analysis shows small vehicle fires can be scaled as a function of the tunnel diameter and the characteristic height of the desired vehicle. The present work provides engineers an appropriate design methodology to undertake informed thermal-structural analysis to minimize the risk of tunnel structural failure.INTRODUCTION Quantifying the effects of a tunnel fire depends on many factors such as the type of occupants, their vehicles and spacing, ventilation conditions and the geometric shape of the tunnel (Ingason and Lonnermark 2011). For design engineers investigating the thermal-structural performance of a tunnel, these factors are typically converted into spatial and temporal temperature distributions (Usmani et al. 2001) using various design curves such as those of ISO834-1, Hydrocarbon, Rijkswaterstaat (RWS) or RABT-ZTV (Promat 2013). However, to define a temperature profile through a structural element these curves require a heat transfer model that incorporates an appropriate boundary condition. The appropriate boundary condition is the net heat flux which is the result of a complex energy balance. For use in heat transfer calculations the net heat flux must account for the tunnel geometry as well as thermal properties of a given structural element and all other surfaces and mediums affecting the transfer of heat (Torero 2014)."

Jan 1, 2016

By A. D. Rovig

Metallurgical evaluation of autogenous grinding of Anaconda's Berkeley Pit ores indicated that tonnage throughput increases, at a finer flotation feed size, were possible by converting autogenaus mills to steel ball mills. In addition, initial test work showed that the improved grind resulted in slight recovery gains in subsequent flotation processing.

Jan 1, 1974

By H. H. Murray

Abstract. World reserves of bauxite are abundant. Domestic reserves are limited and as a consequence the United States must rely on foreign suppliers for over 90 percent of its bauxite. Nationalization of many bauxite mining operations, levying of higher taxes, increased production and transportation costs, and attempts to create a uniform market price combined to place the United States in a vulnerable position. Alumina from kaolin, alunite, anorthosite, and oil shale have-been-or are being evaluated. World bauxite reserves are increasing and attempts to establish a uniform price have failed; therefore, it may be many years before domestic non-bauxite sources of alumina can compete with imported foreign bauxite.

Jan 1, 1980

By H. Kellerwessel

This paper refers to the new crushing and grinding process, which was invented by Professor Schönert (Ref.1), Clausthal, Germy (author of one of the papers presented at this meeting). The process is known as high pressure particle bed comminution or interparticle crushing. Several papers by Professor Schonert and his coworkers and by specialists of the companies producing the necessary equipment under license agreements already described fundamentals of the process, the equipment used, results of lab size and large scale tests and finally the first results of truly commercial operations (Ref .2 to 11). Therefore it should be sufficient to summarize the main facts here: - To a bed of bulk material a pressure of more than 50 MPa is applied. Comminution is achieved mainly by the pressure which one particle transfers to the other and not by squeezing single particles between the working surfaces of some crusher or grinding media.

Jan 1, 1987

By YONGQIONG YANG, Ning Wang, CHONGGUANG LUO, LI ZHU, Hanjie Wen, SHENGJIANG DU, Hannian Gu

Niobium in kaolin clay from the Late Permian sequences was reported in the range of several hundreds of micrograms per gram and was considered as a potential resource for its high concentrations and large areal distribution. Ti-bearing minerals associated with kaolin clay were identified as the main host phase for niobium in some case studies. However, the correlation between the concentration of niobium and titanium is poor, and the types of Ti-bearing minerals and modes of occurrence of niobium are not clear. Typical kaolin clay samples from the Late Permian sequences from southwest China were characterized, and the final products derived from kaolin clay sample were investigated using XRF, ICP-MS, XRD, SEM, and TEM (EDS). The results reveal that there were three types of TiO2 mineral phases in the clay samples: (a) massive TiO2 minerals and (b) aggregates of nano TiO2 minerals did not contain niobium while (c) granular TiO2 minerals were the source of niobium from the EDS analysis. The granular TiO2 minerals included anatase and rutile, both of which were the sources of niobium in kaolin clay in the current study. The findings are of great theoretical implication for source and origin study of Ti-bearing minerals and guidance for separation and recovery of niobium from kaolin clay.

Nov 30, 2020

By E. Watkins, M. B. Daza

Although there have been great advances regarding the understanding of mine fires in underground mines in the last century, fires remain high risk incidents. During fire scenarios, many crucial decisions and actions can be made that greatly influence the outcomes of these scenarios. Underground worker decisions are mainly based on training and experience, which in some cases can be complemented with previous analysis of fire effects. In order to review the guidelines that should be taken into account for this kind of examination, a numerical analysis of effects produced by a shuttle car fire under five different ventilation conditions was carried out. The analysis provides some insightful recommendations for firefighting personnel such as time for direct attack and best attack position for first responders and fire brigade groups. Also, the most critical parameters for each scenario were determined. Finally, all results were systematically organized and a first approximation of a fire classification based on the tenability limits was provided for first responder and fire brigade groups. The methodology used in this study for the fire classification could allow for the most appropriate decisions by firefighting personnel increasing the probability to put fires out without compromising their health and safety. INTRODUCTION While there have been great advances regarding the causes of mine fires in underground mines in the last century “small fires have occurred and always will occur in underground mines” (Conti, Chasko, Wiehagen, & Lazzara, 2005). The response time and decisions made during an underground mine fire are critical elements that have direct influence on the event outcome. Mine fires can grow in size quickly causing catastrophic consequences, thus rapid and suitable response actions can result in the difference between an minor emergency situation and a disaster. Upon the confirmation of a fire, a decision must be made regarding whether to fight the fire or evacuate the mine. Even though all underground coal mines possess emergency response plans and firefighting personnel are highly trained, decisions can be complemented with previous numerical analyses. Such analyses could contribute with the knowledge of potential fire effects and consequently with fire preparedness in the mine. Preparedness in underground mines is an important element to reduce the probability of the negative consequences of a mine fire. The time elapsed between the detection of the fire and response in the early stage is a serious component since small fires can produce larger and more serious consequences. If a mine fire cannot be put out within the short time after discovery, the chance of getting the system back in balanced or the success of safely controlling and extinguishing a mine fire is reduced (Conti et al., 2005, Conti, Chasko, Wiehagen, & Lazzara, 2000, Trevits, Yuan, Teacoach, Valoski, & Urosek, 2009, Brake, 2013). As confirmed by Conti and others, if a mine fire cannot be controlled by direct firefighting methods the probability of extinguishing the fire, without sealing is greatly reduced (Conti et al., 2005). However, response actions such as direct extinguishment must be carried out without compromising the health and safety of the firefighting personnel (Kim, Lönnermark, & Ingason, 2010).

Jan 1, 2019

By Peter Zhang, Daniel Su, Bo Hyun Kim

Shale gas wells drilled in longwall chain pillars are influenced by longwall mining. Longwall mining on each side of the chain pillars can create overburden movements and induce deformations in gas well casings. If the deformations result in a casing breach, intrusive shale gas could leak into the longwall mine with serious safety consequences. This study concerns five shale gas wells in the chain pillars between two adjacent longwall panels in the Pittsburgh coal seam under a cover depth of 670 ft and a mining height of 7 ft. The gas wells were constructed with typical casing design, but a casing cementing alternative with uncemented production casings was practiced. Four production casings were uncemented, and one production casing was unintentionally cemented with good quality cement to a 535-ft depth and low-quality cement stringers from a 444- to 535-ft depth. The longwall faces passed by the shale gas wells as each adjacent longwall panel retreated. Production casings were surveyed by a multi-finger caliper after each panel was mined. No deformation was detected in the four uncemented production casings, but small deformations were detected in the partially cemented production casing. The maximum measured deformation in the cemented production casing was 0.05 in. after first panel mining and 0.06 in. after second panel mining. The casing deformations were also predicted by the FLAC3D model set up on site-specific overburden geology. The predicted deformations were in good agreement with the measurements in terms of deformation locations and magnitudes. All five shale gas wells resumed normal production after being temporarily plugged during the period of mine-by. This study provides a successful demonstration of the effectiveness of a casing cementing alternative for decoupling production and intermediate casing, and thus minimizing the influence of longwall mining in the shale gas wells drilled through longwall chain pillars.

Jul 1, 2023

By C. K. Skokan

Various geophysical tools have been tested over the last eight years to evaluate their usefulness in defining damaged rock zones in an underground facility at the WIPP site in New Mexico. These tools include direct current and frequency domain electrical methods and seismic tomography. The electrical measurements show a "drying rind" to exist around older excavations. Seismic tomography confirms that a rind of lower velocity has developed along walls. In combining these tools, a monitoring program has been proposed to observe long-term changes in bedded salt. Results from the monitoring of electrical data over a 2-year time period illustrate the applicability of the technique in an underground environment.

Jan 1, 1993

By Hamid Maleki

Mine seismicity is influenced by the mechanical properties of both near-seam strata and overburden/underburden and the prudent selection of mining methods and mine layout designs, utilizing sitespecific structural setting of the mines. The importance of adequate data collection, monitoring, and prudent structural designs has long been recognized and utilized in many U.S. operations with adequate engineering resources. In this paper, two case studies of historic seismic events and contributing factors, in deep coal and trona mines with overburden thickness exceeding 1,500 ft, are reviewed using observations and analysis. By back analyzing the overburden response in a historic room-and-pillar coal mine, the overburden collapse mechanism associated with a 3.3 magnitude seismic event is reviewed as well as the need for improvements in designs including panel and barrier pillar widths. Similar high-order seismic events were also experienced in trona mines of the Green River Basin during 1990s, interrupting room-and-pillar mining and creating ground control concerns. Efforts to improve structural mine designs are described in this paper leading to stable and productive operations for decades following the high-order seismic events in both coal and trona case studies. These efforts included improving room-and-pillar extraction layouts and utilizing properly designed longwall mining techniques that were verified using long-term geotechnical instrumentation. The study mines are located on the Wasatch Plateau (WP), Utah and in the Green River Basin (GRB), Wyoming. More recently, in Utah’s East Mountain alone, Energy West Mining Company (EWMC) has extracted some 165 million tons of coal without any significant incidents. Overall, favorable geologic conditions and prudent mine layout designs are key elements to this successful experience in both single- and two-seam layouts. Utilization of conservatively designed longwall mining technique in the GRB has been geotechnically stable, using reported experience in 15 panels and monitoring results in the Northwest (NW) District with measurable longwallinduced seismicity being rare. These studies demonstrate a considerable amount of progress that has been made within the last four decades in the application of longwall mining technique, integrated monitoring, and analyses for the verification of structural designs in mines in the United States.

Jul 1, 2023

By B. P. Atkin, D. W. Brown

A handleability monitor was designed to provide a simple, rapid, on-site assessment of the whole or part consignment of a coal blend in its "as-received" condition. The monitor was evaluated at a number of coalhandling plants, which handle both metallurgical and power station coals from a variety of sources worldwide. The results can be used to predict which coals could routinely pass through a handling plant at line capacity without causing blockage or delay. Despite extensive analysis of the data, it was not possible to correlate the handleability index to the regular sample analysis of moisture, ash and size analyses of the coal blends.

Jan 1, 2002

By O. A. Paulson, D. D. Runnells, D. P. Dupon, K. J. Bruxvoort

Background groundwater quality is often used to drive remediation programs at sites with waters that have been affected by mining activities. In the past, these levels were sometimes chosen without rigorous statistical and geochemical analysis. A probability-distribution approach was used at the Sweetwater Uranium Project to separate a large set of geochemical data into populations that represent contribu¬tions from different sources. Natural background populations were identified for major ions, metals and radionuclides, and these were submitted to the US Nuclear Regulatory Commis¬sion (NRC) to modify the extent of a corrective-action pro¬gram and to establish control limits for future monitoring.

Jan 1, 2000

By S. F. Walsh

The San Manuel Oxide Pit is located within the subsidence boundaries of Magma Copper Company's block caving operation. Ground conditions offer a constant blasting challenge and vary from hard, competent crystalline rock to widely spaced fracturing in a sedimentary conglomerate. A successful drilling and blasting program has undergone several changes since mining commenced in 1985 and continues to be developed. This paper discusses the site specific progress made with the drilling and blasting program from selection of feasibility parameters to current practice. Topics discussed include controlled blasting, use Of high energy blasting agents, charge decking, blast casting, as well as standard drill and blast techniques.

Jan 1, 1988

By P. M. Brown

The Bureau of Mines, U. S. Department of the Interior, has developed a method of dewatering clay slurries based on flocculation by high-molecular-weight polymers and water removal from the formed flocs using a trommel or hydrosieve. The exchange ion on the clays affects their dewaterability. Metal ions in solution and on the exchange sites of smectite clays are known to act as Lewis acids. Recent work has determined that these ions can be titrated with high-molecular-weight polymers. The relative acidity of the exchange ion and the basicity of the polymer determined by the new method give insight into the dewatering mechanism.

Jan 1, 1988

By G. M. Ellis

This paper deals with some aspects of concrete construction in remote locations and/or cold climates. The writer's experience covers 25 years in construction in western and Central Canada. I will bring forth some pertinent observations and cost facts learned from this experience. Let us start by saying that there is nothing more important than preplanning the entire project. By this I mean the production of the engineering design, working drawings, soliciting of prices and ordering of all equipment and contractors work, the delivery of all equipment and all onsite work. All of this should be placed on a master schedule, preferably a C.P.M. We have been using C.P M. Scheduling for all of our work for 5 years and have found it in-valuable. This preliminary schedule will show initial items of work and target dates. After main equipment orders are placed and deliveries confirmed, the construction schedule can be revised to include manpower and construction equipment requirements. From this information the size of camp is determined. This, of course, must be ordered several months ahead. The manpower schedule can be broken into trades to tell us the number of men of each trade required at any time. This is important in helping to determine where the men must come from and whether or not any incentive is needed to get them. The schedule will also point out if it is impossible to get the project closed in before winter becomes too severe unless overtime is worked or the project is started in early spring. In most parts of Canada cold weather starts in October and lasts through April. A common term of reference has been to wait for the frost to come out of the ground before starting work in the spring. In some areas this can be as late as June. The construct-

Jan 1, 1971

By D. M. Anderson

The current mine closure process is faced? with the formidable challenge of controlling environmental and legal liabilities that are associated with mine closure. The current level of environmental statutes and regulations, and the legal/liability considerations, has evolved through regulatory enactment of mine reclamation laws and other existing environmental laws, such as the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). Management tools and techniques to limit risk exposure and financial losses should be employed as an active measure throughout the mine life, including closure and post-closure.

Jan 1, 1995

By Edwin B. Wilson

Over the past several years, state governments have been vigorously refurbishing old health department agencies and smoke control laws in anticipation of pending federal developments. Many states now possess a mature air pollution control administrative organization and a fairly sophisticated set of regulations on air pollution, This developing network of state control legislation and regulation is the machinery which will be called upon to implement federal standards, In order to prevent the wasted effort and resources which inevitably result from hasty action, industry should be in con- tact with local and state control agencies and be familiar with lines of communication to agency representatives. Thorough knowledge of applicable laws and regulations, both current and pending, is required. Moreover, federal law and future federal air pollution control plans, should be well known. Industrial air pollution control should be geared to a long range plan which utilizes existing technology while at the same the recognizing that today's technology will be improved upon with time, Regulation, too, can be expected to become more stringent. The implications of air pollution control in the Appalachian region of the United States will be felt most strongly by the coal industry of this area. Either directly or indirectly most regulations in these states have a significant bearing on coal mining, processing, utilization or waste disposal. The extent of coal-related activity in the Appalachian States of West Virginia, Pennsylvania, Maryland, Virginia, Kentucky, and Tennessee can be observed from the data provided in Table I. This data indicates that 86 percent of active bituminous coal mines and 69 percent of bituminous coal production were accounted for by these states. The purpose of this paper is to provide information on current and proposed legislation and regulations on air pollution in the Appalachian states, The information should prove valuable not only to the coal industry but also to industry in general as a means of evaluating both pollution control action that has been taken to date and the course of future control measures. Reference information in the forms of addresses of appropriate agencies and citations to specific state laws and regulations is provided. All information is current as of February, 1969.

Jan 1, 1969

By William P. Lorenz

Overlying the sulfide mineralization at Anamax Mining Company's Twin Buttes Mine is an oxidized zone up to one hundred meters in thickness. The principal copper minerals in this zone are chryso-colla, tenorite, cuprite, native copper and copper-manganese-iron wad. This ox¬idized zone also contains minor amounts of uranium ranging in concentration from 0.002 to 0.010 percent. Since pit development through 1980, some 38 million tonnes of oxide ore with copper contents greater than 0.6 percent have been brought to the surface. Copper in the oxide ore is extracted at Twin Buttes in, an agitated sulfuric acid leach plant followed by solvent extraction and electrowinning producing 90 tonnes per day of copper cathode. During leaching of the oxide ores small amounts of uranium are solubilized along with the copper values. This is not limited to Twin Buttes as most acidic copper bearing leach solutions throughout the southwestern United States contain small amounts of uranium.1

Jan 1, 1982

By M. Woodie

INTRODUCTION Information such as application review to choose the proper style of vibrating screen, parameters that determine the proper size of vibrating screen, engineering design information that governors proper screen design, review of topics that govern proper isolation from structural steel and other topics that dictate proper screen selection for applications will be presented in this paper. Topics like process and application information review to choose the style of screen and how material size and type influences proper type of screen selection (multi-slope, incline, horizontal, linear incline or dewatering) will also be discussed. Parameters will be reviewed that help size the screen for the application. The total amount of surface area to size a screen is critical to the overall success of a screen installation. Once proper style of screen is determined there is an engineering process that is required to design the screen to operate correctly in the environment it will be used. Finite Element Analysis, Dynamic Modeling, Field Vibration Analysis and other engineering tools will be reviewed to best implement a successful vibrating screen installation. TYPES OF SCREENS Multi-Slope Multi-Slope vibrating screens are used where sizing large amounts of tonnage on surface areas that would be smaller than conventional screening where roughly 6” (150mm) minus material is required to be sized. Occasionally larger particle sizes can be screened on the Multi-Slope machine but the effectiveness of the machine can be diminished with larger particle sizes and larger than 4” (100mm) screen opening. The most common and effective size range of screening with these machines is 2” (50mm) minus material. The Multi-Slope screen is used where particle size is not extremely important. Mineral processing, hard rock mining and industries where exact material size is not critical are best suited for this equipment. Because the aggregates industry requires very specific material sizes, the Multi-Slope screen is not suited for most aggregate screen applications. The key to the success of a Multi-Slope screen is proper material presentation at the feed end of the screen. This allows for the material to stratify quickly and disperse the fines through the screen quickly with a relatively thin bed depth at the feed end which allows the undersize material through the screen quickly.

Jan 1, 2019