Search Documents

By B. Dabrowski, J. D. Miller, D. Halbe, J. Hupka

An air-sparged hydrocyclone (ASH) mobile system was evaluated for continuous stripping and recovery of cyanide (the AVR process) from process water at a gold plant site. The ASH unit performed exceptionally well as an absorber. HCN was removed from the gas phase in a single one second pass with an efficiency exceeding 99%. HCN concentration in the discharged gas phase was lower than 10 ppm, which provided for a safe working environment. The stripping efficiency, controlled by the Henry’s Law constant, exceeded 40% in one pass.

Jan 1, 2004

By R. Debkowski

Mining methods used to protect the workings in underground salt mines against the destructive activity of natural factors are presented in this paper. Major hazards and methods of elimination of their impact on the stability of workings, were determined. Old and modern technical means and technologies used for protection and preservation of the selected most interesting sites were characterized. The results of surveys and studies allowed proposing the change of mine structure i.e. dividing it into monumental and not-monumental part, which should improve execution of necessary protective works.

Jan 1, 2006

By Mark R. Stanton, Douglas B. Yager

Integration and synthesis of mine-site topography, geophysical, and geochemical data yields both two- dimensional and three-Amensional perspective models for the May Day mine located in the Cement Creek drainage near Silverton, Colorado. Induced polarization, geophysical data are spatially registered with geochemical data acquired from drill hole cuttings that are contoured m three-dimensional space, thereby permitting determination of the most metalliferous and sulfur rich zones of a waste pile. This spatial modeling application was developed to be a visually intuitive tool to aid in mine waste reclamation.

Jan 1, 2000

By L. Sletmoen, P. Rocque, E. DeSouza

Plans for achieving planned production rates at the Red Lake Mine High Grade Ore Zone required that the mine ventilation system be upgraded. Time constraints required that only a site assessment of the mine ventilation system be performed followed by recommendations for providing adequate ventilation conditions at the production zone. This paper describes the engineering assessment, design and commissioning of the ventilation system upgrade for achieving increased flows at the high grade ore zone. The work was successfully achieved with minimal capital expenditures and disruption to the mining cycle.

Jan 1, 2003

By T. M. Yegulalp

A numerical model is being developed to assess the enhancement of permeability by improved fracture connectivity by micro-hydrofracturing. A generic two-dimensional percolation model has been developed to test the impact of various field conditions on permeability. Field data from Cyprus Minerals' Mineral Park Mine has been used to establish statistical properties of the observed fracture systems. Results of statistical anlyses of the field data and examples of the use of percolation model are presented.

Jan 1, 1995

By R. L. Thoms

Compressed air energy storage (CAES) has been initiated recently in West Germany with a 290 MW peaking-power facility utilizing twin cavities with volumes of 150,000 m3 each in the Huntorf salt dome (1). The implementation of CAES in several geologic media is being studied carefully in the United States (2); however, the use of cavities for CAES in salt domes or salt anticlines and the associated long-term stability of these cavities is the specific topic of this paper (3). The cavities represent an essential element in a CAES plant, and thus should be designed and operated to perform with "stability" over the planned life of the overall facility. As employed herein, cavity stability implies the extent to which an acceptable amount of cavity storage volume can be utilized with economic maintenance over the planned life of the overall facility. In this sense stability is relative to the planned use of a storage cavity. Figure 1. depicts the salt deposits of the United States (U.S.) (4). The Gulf Coast region includes the only confirmed salt dome basin in the U.S., although salt structures also exist as anticlines in the Paradox Basin of Utah and Colorado. Because of the relatively small amount of elevation change within the Gulf Coast, CAES in salt dome cavities appears to hold considerably more potential for energy storage in this region than more traditional "pumped hydro" systems.

Jan 1, 1979

By Koehler Stout

Stopewall or room closure can be a problem in nining operations. In some mines, wall closure causes ore passes and nanways to collapse when they are enclosed in nine fill. When this phe- nomena occurs, heavy ground and, or, rock bursts frequently happen. Often, ground problems become progressively worse as mining in the stope block progresses toward the upper level. The sill and pillars in the level above may experi ence heavy ground and bursts. Sometimes the conditions get so bad in the stope that it is unsafe to mine the ore, so the stope is abandoned and the ore is lost.

Jan 1, 1980

By R. E. Scheffel

In February, 1976, Ranchers Exploration and Development Corporation obtained an option from Foote Minerals, Inc., to evaluate reprocessing of two uranium tailing piles. Foote received ownership of the Naturita and Durango tailing piles in 1967 through the purchase of Vanadium Corporation of America. The option was exercised in November, 1976, after initial testwork proved that a viable extraction technique existed. Preparation for production at Naturita began immediately with engineering and en¬vironmental permitting proceeding simultaneously. Production began in December, 1977, just 22 months after acquisition of the property and-was completed 17 months later.

Jan 1, 1981

By Stephen L. Bolivar

The Prairie Creek intrusion, near Murfreesboro, Arkansas, is the site of the only commercial diamond mine in North America. Three major lithologies are associated with the intrusion, a hypabyssal peridotite, a volcanic breccia in .which the majority of diamonds occur, and associated tuff. Previous studies, including mining history, geological, geophysical, petrological and whole-rock and mineral chemistry are reviewed. The recent suggestion, by other workers, that this intrusion may be more correctly called a lamproite is examined and supported. This has serious implications for diamond exploration in Arkansas and elsewhere in the U.S.

Jan 1, 1984

By Juan Ares, Enrique Fernández, Alejandro Sanz, Francisco González

"INTRODUCTION Crossrail is a subsidiary company of Transport for London created for the construction of a new transverse train line 118 km long between Maidenhead and Heathrow in the West, and Shenfield and Abbey Wood in the East, including 21 km underground below London. Crossrail C305 Eastern Running Tunnels project is the biggest contract within Crossrail Project and involved boring 11.8 km of twin tunnels through London’s city center. Crossrail C305 Project interfaced with different contracts along its alignment and therefore logistics and solutions had to be developed to minimize disruptions or interferences with other contractors and the neighborhood. The paper describes this innovative approach. C305 CONTRACT APPROACH C305 contract was split into three drives, to be excavated by four EPB TBMs 7.1m diameter, as shown in Figure 1. •,Drive Y: 8.2km long between Limmo Peninsula and Farringdon Station in the city center •,Drive Z: 2.7km long between Pudding Mill Lane and Stepney Green Junction •,Drive G: 0.9km long between Limmo Peninsula and Victoria Dock Portal in the East. Crossrail C305 Project scope of works included the excavation of TBM tunnels and shafts at Limmo Peninsula and Stepney Green (including 17m span turnout caverns), along with the requirement to traverse station and shaft structures of other Crossrail contracts. Limmo Peninsula Site was a strategic element as it was the only access point on the tunnel alignment with sufficient available area at the surface for tunnelling logistics and also connected to the Lea River, tributary of the River Thames which facilitated marine operations for segment supply and muck removal. These were the reasons for operating Drive Y & Drive G TBMs from that location. Drive Z TBMs were originally planned to be launched from Stepney Green to Pudding Mill Lane, supplying the TBMs during Drive Z excavation from Limmo Peninsula site through the excavated section of Drive Y between Limmo and Stepney Green. During the early stages of the project, a value engineering proposal with a new tunneling strategy was agreed wherein the Pudding Mill Lane contractor would provide space for TBM assembly and operation in their portal, allowing for reversing Drive Z excavation and launching the two TBMs from Pudding Mill Lane. This optimization reduced some of the shaft requirements at Stepney Green which were contingent upon critical enabling works and provided program certainty and cost savings for the full Crossrail Project. It allowed for the reuse of both the Drive Z TBMs for Drive G excavation from Limmo to Victoria Dock Portal thereby saving on the procurement of two TBMs, in addition to easier logistics for both Drives Y&Z, therefore de-risking the TBM excavation process and the C305 Project program completion."

Jan 1, 2016

By Roussos Dimitrakopoulos, Liam Findlay

Semimobile in-pit crushing and conveying (IPCC) systems can help reduce truck haulage in openpit mines by bringing the crusher closer to the excavation areas. Optimizing a production schedule with semimobile IPCC requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout and truck fleet investment decisions. A mining complex with multiple mines and IPCC systems should be optimized simultaneously to find an optimal schedule for the entire value chain. An integrated stochastic optimization framework is proposed to produce long-term production schedules for mining complexes using multiple semimobile IPCC systems. The optimization model has flexibility to select the crusher locations and conveyor routes from anywhere inside the pits. The framework uses simulated orebody realizations to consider multielement grade uncertainty and manage associated risk. A hybrid metaheuristic solution approach based on simulated annealing and evolutionary algorithms is implemented. The method is demonstrated using an iron ore mining complex

Nov 1, 2024

This paper summarizes the process development behind the design of three different types of paste fill plants at operating Canadian hard rock mines. Each application has a unique paste backfill mix and process which utilizes the materials economically available to the mine site. The different plants produce paste fill composed of base metal tailings, a blend of recovered disposal pond tailings fines and alluvial sand, gold ore tailings, and a blend of gold ore tailings and alluvial sand. This work has led to the joint development by Inco and GL&V Ontario of the compaction storage mechanism for the de-watering of mill tailings to a paste consistency.

Jan 1, 1994

By J. H. Desautels

The modern coal mining industry is subject to a vast array of regulations affecting virtually all aspects of its operations. Probably the most significant over-sight role involves the Office of Surface Mining Reclamation and Enforcement (OSH) established by the Surface Mining Control and Reclamation Act, or SHCRA.1 Although complying and coping with SHCRA can be difficult for coal operators, this complex regulatory process has helped insulate the industry from ongoing efforts to extend regulation under the Resource Conservation and Recovery Act, or RCRA, 2 to aspects of the mining industry in general. The Environ-mental Protection Agency (EPA) has struggled with regulation of mining wastes under RCRA since the mid-1970's, but RCRA itself places most coal mining wastes firmly under the control of OSH and SHCRA. Despite the general exemption from RCRA regulation for waste materials that result from extraction and processing of coal itself, there may be circumstances under which coal mining operators could find themselves subject to regulation under RCRA or a number of other statutes administered by EPA. This paper will review briefly the history of mine waste regulation under RCRA, as well as touch on the policy decisions that led to the exemptions from RCRA regulation. The paper will summarize coal waste requirements under SHCRA, and also will review what operations at coal mines need to be controlled, in order to avoid potential liability under RCRA. In addition, it will mention requirements under other federal laws, including CERCLA, or the "Superfund" law,3 and describe how they may impose restrictions or liability on coal operations for waste or other materials commonly found at surface and underground coal mines.

Jan 1, 1993

By Andrew J. Neale, Chelvan Veloo

P.T. Freeport Indonesia currently operate a 600,000 t/d mining and 125,000 t/d milling operation in the remote highlands of Irian Jaya, Indonesia. The isolated location and generally difficult working conditions make for challenges not encountered in most North American operations. In spite of this, the mill technical groups have been able to develop and maintain a highly effective level of plant wide automation. This has been achieved through the appropriate selection of available technologies and the implementation of innovative management practices. This paper provides an overview of the control systems currently installed and focuses on those practices which have resulted in the long term success of process control at Freeport.

Jan 1, 1997

By Yuting Xue, Todd Minoski, Daniel Su, Mark Van Dyke, Mark Mazzella, Steve Hicks, Zoheir Khademian, Nicole Evanek

Design of chain pillars in a longwall mine setting is one of the main engineering controls on the global and local stability of the mine. Challenges with roof instabilities, floor heaves, and pillar failures can be alleviated, to some extent, by careful design of gateroad configurations and chain pillars. This work investigates three different alternative designs in a three-entry-system gateroad configuration with an inter-panel barrier in a longwall mine in Virginia. Starting with the current design, which has faced challenges such as excessive floor heave, a geomechanical model developed in 3DEC software is validated by monitoring in-situ pillar stress in the yield, abutment, and barrier pillars in the mine. Next, three different chain pillar designs are evaluated in the model with a focus on roof sagging, floor heave, and pillar average stress. Results show the relationships among the alternative designs and instabilities associated with roof, pillar, and floor in the study mine, providing insights for optimizing longwall mining designs in deep-cover settings.

Feb 1, 2025

By Douglas B. Silver

Study Parameters (Status as of February 1993) Time Period: 1989 -1991 151 North American Public Metal Mining Companies Fiscal not calendar year basis 85+% of Canadian and U.S. Metal Production Au, Ag, Cu, Pb, Zn, Mo, Ni, W Results are Preliminary and Research Continues Chicken Little is Alive and Well

Jan 1, 1993

Giant gold deposits are considered products of crustal-scale systems. Reduced fluids stored in mid to lower crustal reservoirs were discharged into mid to upper crustal sites of deposition. Elements of the architecture include crustal-scale structures, reduced packages of rock and regional seals. Gas-rich aqueous fluids were common but non-aqueous fluids may have been significant in the deeper parts of the systems. Fluid fluxes in over pressured domains were maintained by porosity waves. Abnormal heat input from the mantle may not be required once the systems were perturbed. Fluid-mixing and hypogene enrichment were probably the most significant precipitation processes.

Jan 1, 1999

By Jeroen van Eldert, Daniel Johansson, Henrik Ittner, Håkan Schunnesson

"Numerous aspects of underground construction, from structural stability to construction costs, depended on the tunnel quality, including blast damage and the Excavation Damage Zone. Accurately quantifying the extent and severity of damaged rock is a problem. Recent technical developments in the field of Measurement While Drilling (MWD), including software for on-board logging and on-site analysis, have shown potential for rock-mass characterization. Ground Penetrating Radar (GPR) and P-wave velocity measurement have also improved and show similar potential. This paper explores the use of MWD, GPR and P-wave velocity measurements and uses them in techniques for excavation damage characterization and prediction. The paper is based on data collected from a small underground waste-collection site in central Stockholm, Sweden. The data is correlated against rock-mass characteristics and their responses are evaluated. Results indicate potential for excavation damage characterization for all tested techniques, which could minimize blasting damage and improve the over-all tunnel quality. 1 INTRODUCTION During underground excavation the rock mass is influenced in many ways. The Excavation Damage Zone (EDZ) is a result of these influences. The EDZ can be defined by an irreversible change in rock mass properties, for example increased permeability. EDZ is influenced by the excavation method, the rock mass properties and the in-situ stresses in the area of the tunneling. Since the 1990s research has been done on the EDZ by Emsley et al. (1997), Christiansson et al. (2005), Olsson et al. (2009), Ouchterlony et al. (2009), Ittner et al. (2014), and Siren et al. (2015). Based on past literature the EDZ have in this paper been separated in the following subzones: 1. Failure Zone or over-break is the area outside the planned tunnel profile, including the Look-Out and hole deviation. This zone consists of fracture networks (both natural and blasting-induced), that caused rock fall-outs. The extent of the over-break can be determined by volumetric scanning and photogrammetry and the half cast factor can be used as a damage indicator. 2. The Damaged Zone is split into three parts and but the quantity and depth of damage is difficult to measure. Although it can be visualized by sawing of rock slices in the tunnel wall (Olsson et al. 2009), diamond coring (DC) or P-wave velocity reduction (Jern 2001): a. Inner Damage Zone (Crush Zone): It is located directly around the drill hole, and is caused by the shock-wave energy of the detonation. The micro fractures in the Crush Zone produce a white-wash (rock dust) in the half cast. b. Transition Zone: This zone consists of micro fractures that connect and form macro fractures, both radially and parallel to the tunnel wall. The macro fractures are caused by the gas expansion during the detonation of the explosive; it increases the pressure in the (micro) fractures and creates the macro fractures. Seismic reflection, rock slicing and core drilling can be used for the examination. c. Progressing Zone: In this zone the existing radial fractures propagate due to the increase gas pressure inside these macro fractures. Examination methods are seismic reflection, rock slicing and core drilling. In addition, the Peak Particle Velocity (vibrations) could be used to estimate the depth (Tesarik et al. 2011)."

Jan 1, 2016

By S. Perla

Two of Peabody Western Coal Company's mine operations are the focus of this paper ... Black Mesa Mine and Kayenta Mine, both located in Northern Arizona. These two locations are unique for a variety of reasons. ? The two mines have only two customers, both power plants, one the Southern California Edison's Mohave Generating Station near Laughlin, NY, the other the Navajo Generating Station near Page, AZ. Close in proximity, these two locations ships nearly 12 million tons of coal per year. ? Material is shipped to these customers two ways: via a 273 mile underground slurry pipeline, which by the way is longest in the world, and by a 17 mile long conveyor to four storage silos. Product is then shipped via train from the storage silos to the plant sites.

Jan 1, 1995

By W. D. Elston, A. E. McLaughlin, G. B. Hampton, W. L. Barham, J. F. Murphy, W. H. Cundiff, J. W. Mulloy, R. G. Breuer, J. W. Shaffer

Introduction Alumina (aluminum oxide) is the material from which all the world's aluminum is produced. In the Western World, all the alumina is made from bauxite by the Bayer process. In the nearly 150 years since aluminum was first isolated by Oersted, the metal has grown from a laboratory curiosity to a position of major importance in the world's commerce. In terms of annual production rates aluminum is first among nonferrous metals. Oersted's discovery-reduction of aluminum chloride with potas¬sium amalgam-was improved on by Ste. Claire Deville, whose so¬dium amalgam reduction of aluminum chloride led to the commercial production of aluminum in France in 1855. Ste. Claire Deville's method prevailed until 1886 when Charles Martin Hall and Paul T. Heroult each invented a process for the production of aluminum by the electrolysis of alumina dissolved in molten cryolite. The inven¬tion by Karl Josef Bayer in 1888 of an economical process for making very pure aluminum oxide (alumina) from bauxite established the necessary link between known ores and the Hall-Heroult reduction process. Bayer's work completed the scientific base-the ore bauxite refined to alumina by the Bayer process (U.S. Patent No. 515,895), the alumina reduced to aluminum in the Hall-Heroult cell (U.S. Patent No. 400,766--upon which today's aluminum industry is founded. Small-scale production of aluminum in the U.S. began in 1888 utilizing the Hall cell. By 1903, bauxite properties and a Bayer process refining step had been incorporated into the production activities. On this base the aluminum industry in the U.S. has grown at an annual compounded rate of 15%. Since 1946 the annual growth rate has been 10%.1 The rapid growth of the industry is the result of many factors among which are the existence of widespread bauxite ore deposits; a sound and economic production technology; and the properties of the metal-lightness, strength, ductility, good electrical and heat con¬ductivity, and pleasing appearance, which lead to ever greater de¬mands for aluminum in an industrializing society. At the inception of the industry, the only market that could be found for aluminum was in the production of cooking utensils. How¬ ever, the rapidly accelerating industrial and technological development of the Western World soon created new needs for aluminum, and today aluminum is marketed in a broad range of industrial, commer¬cial, and consumer applications. The principal uses for aluminum are:' building and construction, 22%; transportation, 18%; electrical, 13%; packaging, 11%; consumer durables, 10%; machinery and equipment, 7%; other, 19%. The 1974 production of primary alumi¬num in the world was 14.5 million short tons, which at an approximate ingot price of 40¢ per lb puts a value of $11.6 billion on the industry product prior to fabrication. While aluminum is widely distributed in the earth's crust and is a major constituent of many rocks and soils, to date no method of extraction of aluminum from such nonbauxite material has been brought to commercial practice in the Western World. In the USSR alumina is produced by the complex processing of nepheline syenite, but elsewhere all commercial production of alumina is from bauxite. A brief discussion of recent developments and other processes for alumina is included in the subsection "Other Processes for Alumina," page 19-15. In early 1973, a major U.S. aluminum producer announced the successful development of processes for the production of aluminum from aluminum chloride. This achievement promises to exert a major influence on the future of the aluminum industry. In the initial com¬mercial application of this new technology, Bayer alumina will be chlorinated, and the aluminum chloride then reduced by electrolysis. Important claims for the new processes are lower energy requirements (one-third less than obtainable in Hall cells) and reduced labor costs. Capital costs are said to be no greater than for conventional plants. While the announced intention is to produce the aluminum chlo¬ride from Bayer process alumina, the new chloride reduction process will eliminate the other raw materials, carbon and fluorides, required by the conventional Hall cells. The electrodes in the chloride cell will not be consumed on the reduction process and the electrolyte will have, as the name indicates, a chloride rather than a fluoride base. 2. Bauxite Definition and Origin. Bauxite is a naturally occurring raw material composed principally of a mixture of one or more of the hy¬drated aluminum oxide minerals gibbsite (Al2O2 3H2O), boehmite (Al2O3 H2O), and diaspore (Al2O, - H2O), and impurities of silica, iron oxide, titania, and other various elements in trace amounts. It is an end or near-end product of chemical weathering. Depending on the amount of iron impurities, the color of bauxite varies from dark red and brown to pink to white. Some bauxite is finely divided, free digging earthy material, while other forms are dense and rocky, requiring explosives in mining. Many gradational forms exist. It is one of the most variable of mineral raw materials in chemical composition and physical appearance. It is generally believed that bauxite deposits resulted from intense chemical weathering of aluminum-bearing rocks or formations under tropical or subtropical conditions with alternating wet and dry sea¬sons. Topographic conditions were favorable for drainage and the in-situ accumulation of aluminum, iron, and titanium oxides. There was low to moderate topographic relief with a minimum of erosion during long quiet periods in earth history.2 The occurrence of bauxite is widespread and it has been found on all continents except Antarctica. Production was reported from 27 countries in 1974, at which time total world production was over 79 million metric tons. Of this production 76% was from seven coun¬tries-Australia, Jamaica, Surinam, Guinea, USSR, Guyana, and Greece-which ranked in that order of production. In Table 1 are shown typical compositions of bauxite from some

Jan 1, 1985