Search Documents

By M. Schultz

The cost of remediation often drives the selection of the preferred remedial alternative at hazardous waste sites. The use of probabilistic cost/risk analyses can aid in predicting costs of remedial alternatives. Three types of information are discussed in performing cost/risk analyses: (1) data on the quantity of contamination versus the contaminant concentration; (2) unit costs of remediation for the remedial alternatives; and (3) risk to contaminant concentration relationships. Cost/risk evaluations are performed on a site-by-site basis, to account for combined risks of different contaminants and differences in quantity to be remediated versus contaminant concentration. The cost/risk analysis produces a graph of risk versus cost for each of the remedial alternatives. These costs are then compared to facilitate selection of a preferred alternative. An example of comparison of alternatives is illustrated for a historic coal gasification site.

Jan 1, 1992

By S. Shankar

Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant. Therefore, as part of the Respirable Dust Center's ongoing research, a three part study was envisaged: study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities; study of the same in the Lake Lynn Laboratory Mine of the USBM with both airflow and walking by personnel causing re-entrainment; and mathematical modeling and computer simulation of the re-entrainment phenomenon. In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory Mine are presented. Further, the results from the wind tunnel studies are compared with the results from in-mine studies conducted at the Lake Lynn Laboratory Mine of the USBM. Comparing the results from the two studies it was observed that increasing air velocity increased the rate of re-entrainment, but increased time of exposure decreased the airborne dust concentration. Compared to same size particles, a mixture of sizes created more airborne dust concentration when re-entrained. It was also observed that contribution of airborne dust concentration due to airflow was negligible compared to the contribution due to walking.

Jan 1, 1995

By H. W. Breathitt

World demand for phosphate rock has increased significantly in the past fifteen years. Prior to the early 1960's, most of the world production was obtained from Florida, North Africa, and Kola. As the 1960's arrived, new mines in North Florida and Eastern North Carolina, as well as expanded production in the Western United States, .increased domestic production. Many new mines overseas have also become significant. This includes countries such as Senegal, Togo, Israel, Spanish Sahara, and Jordan. Limited production, often as by-products, has been noted in South Africa, Brazil, and other countries. In recent years, and even recent months, we have learned of many new areas being considered as potential sources of phosphate rock. This includes Australia, Saudi Arabia, Mexico, Colombia, and Brazil. Many other developing countries have discoveries and are considering their new deposits, often with difficult beneficiation problems, as potential sources of phosphate. These factors all relate to expanded world, population and the demand for more fertilizer products to produce food. In this paper, four areas of the world with different types of phosphate deposits are briefly reviewed to contrast the ore beneficiation problems to Florida procedures--long considered the "standard" of the industry, at least for most of the United States' domestic production. Agrico has three large operating mines in Florida with total production capacity exceeding seven million tons per year. Here, pebble phosphate (+14 mesh material) is produced without the use of flotation, whereas all of the material finer than 14 mesh is subjected to flotation beneficiation to upgrade into high grade concentrates.

Jan 1, 1977

By Edwarde R. May

The Flambeau volcanogenic massive sulfide deposit located in northwestern Wisconsin occurs within the southern lobe of the Canadian Precambrian Shield. The steeply dipping tabular body occurs in a complex pile of cyclic schistose intermediate to felsic fragmental volcanics. No chloritic alteration pipe is recognized but adjacent rocks have undergone magnesia metasomatism and subsequently were metamorphosed to the upper greenschist and lower amphibolite facies. Although modest in size the deposit is of special interest in that it has an extensive and well preserved supergene enrichment blanket. Economic minerals found within a pyritized quartz-sericite schist are chalcocite and bornite overlying primary chalcopyrite.

Jan 1, 1976

By H. L. Holden

The single line grinding circuit at Bond Gold's Colosseum mine consists of variable speed drive semi-autogenous (SAG) milling and secondary grinding with a fixed speed ball mill. There are several advantages and disadvantages of operating SAG mills with variable speed drives. Discussion in this paper will focus on the effects of variable speed SAG milling in relation to mill liner wear, grinding media consumption, and mill operating availability. Operating experiences, corresponding mill data, and pertinent design changes are also presented.

Jan 1, 1991

By S. Mathur

Polyacrylic acid (P AA) was evaluated as a selective flocculant for dolomite-apatite system. P AA of 4 million MW was found to flocculate both dolomite and apatite. However, their flocculation behavior was significantly different with 450,000 MW PAA which was the lowest molecular weight fraction capable of flocculation. In single mineral tests, at a dosage of 2kg/t 90% of dolomite and 35% of apatite flocculated. Selectivity was achieved in mixed mineral tests where apatite of 90% grade at 70% recovery level was obtained in the concentrate from a feed consisting of 80:20 mixture of apatite and dolomite. The dolomite rejection was about 75% which corresponds to 1% MgO in the concentrate.

Jan 1, 1995

By M. G. Vieira

This investigation addressed the possibility of producing pellet feed at a silica content of = 1.0% using a representative sample of Samarco´s mechanical flotation tailings. This sample contained 11.0% Fe and presented an F80 = 116 µm and a d50 = 63 µm. The higher silica content was verified in the coarser fractions and the higher iron content in the fraction -37 µm. Specular hematite is the most abundant mineralogical phase in the fraction -37 µm. The technological tests used one of four methods: magnetic concentration using a wet high-intensity magnetic separator, magnetic concentration using a SLon high-gradient magnetic separator, reverse flotation or direct flotation. The methods using the magnetic concentrator SLon, reverse flotation and direct flotation did not present results meeting the target of the study: iron content in the concentrate (rougher stage) greater than 34% or iron recovery greater than 80%. Cleaner stages were not achievable with the resulting concentrates. In contrast, the most successful method consisted of using wet high-intensity magnetic separators (WHIMS) as a rougher stage and reverse flotation as a cleaner stage. Using this route, it was possible to produce a pellet feed with a silica grade of 1.0% and high specular hematite content.

Jan 1, 2010

By K. T. Valsaraj

The separation process called solvent sublation for the removal of two hydrophobic compounds (penta-and tri-chlorophenols) from the aqueous phase is discussed. A steady state mathematical model for the process is discussed. The process was conducted in a continuous countercurrent mode. The underlying mechanisms, theory and experimental details on the effects of process variables on removal efficiency are reported.

Jan 1, 1992

By John Kuyt, Zili Li, Michael Mooney, Michele Mangione

"INTRODUCTIONTwin bored tunnels are commonly used for a variety of road and tunnel projects throughout the world. A major component of these twin tunnel projects is the construction of connecting cross passages that provide emergency access between tunnels and space for tunnel service equipment. Cross passages can present significant geotechnical risk and technical challenges to a project – support systems must be considered for redistributing loads around the mainline tunnel openings and supporting new loading resulting from excavation activities. Additionally, cross passages pose risks to construction schedule and cost because of their sequencing at the end of construction, so mitigation of schedule overruns can be critical. By observing field instrumentation data records from completed projects, a betterunderstanding of the force development in each temporary structure can be achieved with indication of which structures are the most critical to support ground loads.This paper discusses the data obtained during the Brisbane Airport Link construction project, a road tunnel located in Brisbane, Australia. Strain gauge instrumentation data from the precast segmental lining and propped opening steel sets is presented with relation to the construction sequence and local geology. Interpretations and conclusions based on the observed trends are proposed, with several key mechanisms affecting the loading and unloading identified.Brisbane Airport Link Project OverviewThe Brisbane Airport Link project in Brisbane, Australia, connects central Brisbane to the airport located northeast of the downtown with over 7km of twin-bore road tunnels, two lanes each, with several caverns, interchanges, and access ramps constructed along the alignment to connect to other key routes in the city. The project was executed under a Public-Private Partnership (P3) scheme, funded and operated by the consortium BrisConnections. The main contractors were a joint venture of John Holland and Theiss, while the design was carried out by Arup and Parsons Brinckerhoff.Construction of the tunnels was conducted using a combination of 17 roadheaders and two 12.5m double-shield Herrenknecht TBMs [1]. The TBMs were used in EPB-type closed mode for the initial portion of their drive, starting at the northeast end of the alignment. Tunneling started in soft ground, weathered rock, and mixed face conditions initially, progressing to competent sedimentary rocks as the drive continued. Support was accomplished using a 12.1 m diameter steel fiber reinforced concrete (SFRC) segmental lining installed behind the TBMs in a 9 segments + 1 key arrangement. The innovative design of these segments is detailed in the paper by Harding and Francis [2]. Ancillary roads and underground interchange caverns were constructed by sequential excavation techniques using roadheaders, accounting for nearly half of the total underground excavations."

Jan 1, 2016

By Fred Heivilin

A symposium on the characterization and toxicology of mineral dusts was held Sept. 19 and20 in Washington, D.C. The symposium was held to update the minerals industry, the health community, government agencies and academia on the technical, health and regulatory aspects of minerals to be evaluated by the International Agency for Research on Cancer (IARC).In October 1996, the IARC met in Lyon, France, to discuss and prepare “Volume 68 of the IARC Mono-graphs on the Evaluation of Carcinogenic Risks to Humans on Silica, Silicates, Dusts and Organic Fibers.”

Jan 1, 1996

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999

By G. Heinrichs

This paper is intended to provide information for one to be able to determine the slurry system head curve for pump applications. The slurry characteristics are the basis for what the size, material of construction, and critical carrying velocity of the pipe will be. The system head curve is adjusted by use of the pipe friction coefficient factor and slurry derate factors. An example using multi-staging of slurry pump curves is presented to compare the wear life relationship of pump parts for a tailing pipeline system head curve.

Jan 1, 1996

By D. A. Augenstein

Operators of coal preparation plants use equipment such as large-capacity dump trucks and bulldozers to haul, spread and compact refuse material to conform to federal and state regulations governing the disposal of solid waste. For example, federal regulations require that refuse be spread and compacted in layers not more than two feet thick. If the refuse layers or piles have poor load-bearing characteristics, movement of equipment over them becomes extremely difficult. The increasing cost and limited space for the construction of settling ponds extensively used for fine refuse disposal are leading to the growing practice of dewatering the fine refuse by means of vacuum disc filters and combining the resulting filter cake with coarse refuse for waste bank disposal. However, this filter cake usually contains more than 25% moisture. Therefore, when it is combined with coarse refuse, the moisture level of the total refuse may become high enough to impair the load-bearing strength of the refuse. Precisely this problem and the attendant difficulties of moving heavy equipment arose when vacuum disc filters were installed at a preparation plant in West Virginia. Combining the moist filter cake with the coarse refuse generally results in a 12% moisture level for the total refuse at this plant. At this moisture level, the refuse can still be handled with some difficulty by the equipment. However, the problem has frequently been compouned after rains.

Jan 1, 1977

By D. L. Lampshire

Biological leaching using native heterotrophic bacteria was studied by the U.S. Bureau of Mines as a means of extracting manganese from a domestic low-grade wad ore. Column heap leaching simulation techniques were employed using molasses as the nutrient source for the bacteria. These column studies were designed to investigate the effects of molasses medium flow rate, concentration, and replacement interval on the extent and rate of manganese extraction. .Results showed that flow rates between 0.41 and 8.1 L/min/m2 had little impact on manganese extraction. The total amount of molasses used did have a direct effect on the extent and rate of manganese extraction. Manganese extractions over 90-pct were obtained in 12 weeks of bioleaching with 2-week medium replacement cycles.

Jan 1, 1993

By V. G. Medina

The 15 000 t/d La Coipa mine initiated operation in July of 1991. The complex consists of a conventional, open-pit mining operation and a mill employing cyanide leaching with Merrill-Crowe gold and silver recovery. The process plant includes a primary crushing circuit, a 15,000 t (live) covered stockpile, a semi-autogenous mill/ball mill/crusher or SABC grinding circuit, a leach circuit, a belt filtration/washing circuit, a zinc precipitation circuit and a "dry" tailing disposal system. The process plant is described in detail with major design considerations used in the selection of the processes and equipment. The unique methodology employed in the disposal of the filtered tailings is also described.

Jan 1, 1992

By A. Sinha, C. Sawmliana, P. Pal Roy

Using the newly developed and permitted explosive Pentadyne-HP (Gulf Oil Corporation Ltd., Hyderabad), the Blasting Department of the Central Institute of Mining and Fuel Research, Dhanbad experimented at the GDK-5 Incline, RG-1 Area of the Singareni Collieries Company Ltd. (SCCL) to establish one modified angular cut blasting pattern as an alternative to conventional solid blasting in India to obtain longer pull, as well as to achieve at least 40 t of coal in a single blast round for the deployment of diesel load-haul-dump units at the face. This permitted explosive satisfied the statutory requirements of incendivity characteristics applicable to P5 explosives of the regulatory agency Directorate General of Mines Safety (DGMS) of India. The present paper summarizes the development of this new blasting pattern and its possible use in Indian coal mines.

Jan 1, 2010

By Stanisław Lasocki

We present an algorithm to integrate the uncertainties of mean activity rate and magnitude cumulative distribution function in the interval estimation of the primary seismic hazard parameters: the exceedance probability and the mean return period. The algorithm is applicable for both the parametric and nonparametric modeling of magnitude distribution. When the Gutenberg-Richter relation-based parametric model of magnitude distribution is used, the interval estimation of its parameters is based on the asymptotic normality of the maximum likelihood estimators. When the nonparametric kernel estimation of magnitude distribution is used, we apply the iterated bias-corrected and accelerated method for the interval estimation, based on the smoothed bootstrap and second-order bootstrap samples. Previous studies indicated that the uncertainty of mean activity rate significantly affects the interval estimates of hazard functions only when the activity rate is low and the inference period is not long (Orlecka-Sikora & Lasocki 2017). With increasing mean activity rate, the uncertainty of magnitude distribution dominates over the uncertainty of mean activity rate in the aggregated uncertainty of the hazard functions. The provided algorithm is generic and can be applied to capture the uncertainty of any multiparameter function from the uncertainties of its parameters. Here we present a further development of the algorithm developed by Orlecka-Sikora & Lasocki (2017) by presenting its implementation in the Traffic Light System approach. As an example of use, we present the confidence intervals estimation of hazard parameters for the datasets related to induced seismicity accompanying underground exploitation of copper ore in the Legnica-Głogów Copper District (LGCD) in Poland. The algorithm is under implementation to the EPISODES platform (https://tcs.ah-epos.eu/) - an IT platform that provides access to integrated research infrastructures of the Thematic Core Service of Anthropogenic Hazards (TCS AH) of EPOS (European Plate Observing System). The algorithm is also a component of the pilot developed within the EPOS SP project (No 871121), which aims to strengthen the interaction with the private sector and the added value for society. The pilot demonstrates the potential of the IS-EPOS platform software applications for the technology-related probabilistic assessment of time-dependent seismic hazard. The pilot supports a Traffic Light System approach. The current seismic hazard is compared to threshold values based on the exceedance probability for a given magnitude.

Apr 26, 2022

By R. Frenette, A. W. Mo, H. A. Hamza

Fine particles present major technical and economic problems to those who deal with solid/liquid separation processes. In the coal industry the problem is compounded by the large amounts of produced fines such as those present in Western Canadian coals. Flocculants in the form of high molecular weight water soluble polymers are commonly considered an effective solution for the enhancement of the separation process. These reagents are relatively expensive especially when considering a low-price commodity such as coal. Optimization of the use of these reagents is therefore an operational necessity. Six polymers were evaluated as to their effectiveness in flocculating a fine coal tailing. Results were compared with those for a reference flocculant, in-use at that time in the washery. It was shown that, in general, flocculants significantly improve the solid/liquid separation process. The ranking of the flocculants as to their effectiveness in settling and filtration indicated that the best flocculants for settling were not necessarily the most effective for filtration. Flocculants that showed the best filtration improvement were generally cationic and those best for settling were anionic.

Jan 1, 1988

By H. Habenicht, E. Urschitz

Three mining methods for full extraction in flat coal seams - i.e., longwall (L W), shortwall (SW), and rib pillar extraction (RPE) - are com- pared with each other in view of the introduction of a mechanized, self-advancing roof support. Features are shown according to which RPE appears most attractive under certain conditions. In this presentation, the mining methods are outlined and discussed. The new support (Alpine Breaker Line Support, ABLS) is described, and its employment is explained. A trial operation in RPE using the ABLS has been conducted successfully in a South African coal mine. The results and improvements are stated.

Jan 1, 1988

By I. M. Arbuthnot

Over the last five years, a large number of small to medium sized carbon-in-pulp gold treatment plants have been built in Australia, most designed to treat between 250,000 -1,500,000 tpa of ore. In many cases, the primary requirement was to get a plant built and operating in a short period of time and at minimal capital cost, relating to the limited capital resources and tight cash flow positions of these relatively small mining companies. Since the inclusion of both pre-leach and tailings thickeners resulted in an obvious and significant capital cost, most plants were built without thickeners, without doing a detailed cost-benefit analysis on their inclusion, However, the increasing use of High Rate Thickener?s (HRT s) in the mineral processing industries resulted in a reassessment, in some cases, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas, where borefields were costly to install and water was limited. It has become apparent, though, since startup and operation of these installations, that the savings in cyanide consumption is also a very significant factor and can be used as a primary justification for the installation of a HRT in many cases.

Jan 1, 1991