Search Documents

By M. A. Trevits

The explosion hazard presented by methane gas in coal is confronted daily in the mining industry. Research has developed several viable methods for gas control in addition to conventional dilution by ventilation. Such methods include the drilling of horizontal or cross-measure boreholes from a mine opening and vertical boreholes hydraulically stimulated in advance of mining or for gob gas drainage. The long-term production history of five gas drainage installations was studied. Three installations were completed in the Pittsburgh Coalbed: two in West Virginia and one in Pennsylvania. The remaining installations were completed in the Mary Lee Coalbed in Alabama and the Sunnyside Coalbed in Utah. The types of drainage methods utilized included horizontal and vertical boreholes. The length of production studied ranged from 860 days to 36 years. The cumulative production from the five sites was in excess of 155 Mm3, representing a significant volume of gas.

Jan 1, 1985

By C. St. J. Lowe

Weir Minerals ? Linatex has developed a new approach to the dewatering of fine solids, particularly mine and process plant tailings and wastes. The Weir process, patented in 2009, uses standard process equipment in a standard flow sheet, but applies this approach to materials previously thought to be too fine to be dewatered with this type of equipment. The process can be applied to a wide range of materials, making lower moisture products that can be re-used elsewhere or sent to disposal. It has already been tested successfully on a small scale in Australia on coal fines, zinc mine tailings, red mud, iron ore tails, and copper/gold tailings. The principal factors affecting the solids recovery have been established as: 1. The % solids in the slurry feed to the process ? a higher % solids provides a higher recovery. 2. The particle size of the feed solids ? coarser feeds provide higher recoveries. The key factors affecting the % solids in the dewatered product have been determined to be: 1. The particle size of the dewatered product - coarser materials produce a higher % solids in the dewatered product. 2. The height of the discharge weir on the dewatering screen - a higher discharge weir on the dewatering screen also yields a higher % solids. 3. The angle of the dewatering screen. Setting the screen horizontal increases the travel rate, reduces the bed depth and reduces the % solids in the dewatered product. Back-sloping the screen up to 5° reduces the travel rate and increases the % solids in product. Eight plants ranging in size from 3 t/h to 40 t/h have been sold to a range of customers in China, for coal and iron ore tailings treatment. Australia has one plant, a small unit rated at 30 t/h of sand fines, and has recently completed test work on iron ore tailings for a dewatering plant rated at 135 t/h. Additional tests are under way with clients around Australia, to demonstrate the capabilities of this process on specific applications and to provide confirmation that materials can be processed successfully, before moving on to larger scale tests or full size plants. The advantages of the Weir process include - lower moisture in products, uses proven equipment, lower capital and operating costs, lower maintenance costs, reduced power consumption, compact footprint, can be used in parallel or in series with existing equipment, modular design to facilitate redundancy or expansion, efficient water recovery and simpler water management, reduced cement in backfill mixes, smaller tailings disposal footprint, reduced earthworks requirements, much lower seepage losses, more stable tailings mass, progressive site rehabilitation, reduced impact on local wildlife, reduced risk of dam wall failure, and reduced environmental monitoring and compliance costs.

Feb 23, 2014

By William A. Vogely, Robert T. Deacon, Walter J. Mead

Oil and gas together are the most important energy sources consumed in the United States. In 1983, 67% of total energy consumption was represented by these two resources (43% was oil and 25% natural gas), while coal accounted for only 23% of U.S. energy use. All other sources (hydroelectric, nuclear, geothermal, wood and other waste products) accounted for only 10% (U.S. Department of Energy, 1983, p. 1). In this chapter we address the issue of regulation in the oil and natural gas sectors of the U.S. energy industry. In addition, we analyze the cartel characteristics of the Organization of Petroleum Exporting Countries (OPEC). If OPEC is an effective cartel, then U.S. oil as well as substitute energy prices, production, and consumption will be affected by cartel action. Further, as the nation learned in the 1970s, major changes in oil prices produced major disturbances in other sectors of the U.S. and world economies. Consequently, it is important to determine whether the roughly ten-fold increase in nominal prices that occurred in the 1970s was the result of cartel action, the result of normal economic forces adjusting to the fact that the world was running out of cheap oil, or some combination of the two. Furthermore, the presence of OPEC- associated oil price increases is related to regulations that were imposed on the energy sector during the decade of the 70s. THE RATIONALE FOR GOVERNMENT INTERVENTION Economists have traditionally judged the state of an economy to be efficient if it is impossible to improve the welfare of any one member of society without harming someone else. Any economy that satisfies this condition is said to be Pareto efficient, after the Italian economist Vilfredo Pareto who first gave rigorous attention to such questions (see Chapter 4.10). It is easy to see why an economy that fails to satisfy this condition could not be efficient; by definition, it would be possible to alter the allocation of resources in a way that improves everyone's welfare.' Much of the appeal of this weak efficiency criterion is that it avoids comparisons of levels of well being among different individuals. The cost of such generality, however, is that in any given economic system a wide array of different Pareto efficient states will typically be attainable. In the simple Robinson Cursoe economy of the undergraduate textbook, for example, efficiency could just as easily be attained in the case where most of the island's resources are owned by Friday as in the case where they are under Crusoe's control. However, the distribution of welfare among the two inhabitants would obviously be quite different in the two situations. Such equity issues cannot be settled on objective or scientific grounds. To decide which distribution of welfare is socially "best" an explicit value judgment is needed. It is useful to keep in mind the preceding distinction between efficiency and equity issues when analyzing the role of government in a market economy. Decentralized market processes will not necessarily result in a distribution of welfare that society considers just. For this reason a potential role for government lies in the redistribution of income among individuals. In some circumstances, however, market pro-

Jan 1, 1985

By Jessica Elzea, Haydn Murray

The term bentonite was first proposed in 1898 by Knight, a year after he had named this clay taylorite, because taylorite had been previously used for another mineral. The name taylorite was after the Taylor ranch, the site of the first mine, near Rock River, WY, and the name bentonite is from the Benton Shale in which the clay was thought at that time to occur. The Benton Shale was, in turn, named after Fort Benton, MT, located more than 640 km miles north of Rock River. Early in the 20th century, several geologists recognized that bentonite, mainly in beds in Cretaceous and Tertiary rocks, originated from transported volcanic materials. This recognition led to definitions based on origin, the one most widely quoted and generally accepted by geologists is the following definition by Ross and Shannon (1926): "Bentonite is a rock composed essentially of a crystalline clay-like mineral formed by devitrification and the accompanying chemical alteration of a glassy igneous material, usually a tuff or volcanic ash; and it often contains variable proportions of accessory crystal grains that were originally phenocrysts in the volcanic glass. These are feldspar (commonly orthoclase and oligoclase), biotite, quartz, pyroxenes, zircon, and various other minerals typical of volcanic rocks. The characteristic clay-like mineral has a micaceous habit and facile cleavage, high birefringence and a texture inherited from volcanic tuff or ash, and it is usually the mineral montmorillonite, but less often beidellite." The difficulty in applying the foregoing definition to bentonite as an industrial mineral commodity is that it is based on origin and is restricted to an ash, tuff, or volcanic glass parent material. Therefore, deposits consisting of the clay minerals required by this definition, but having uncertain origin or parent materials, cannot properly be called bentonite. Furthermore, many deposits in the western United States and in other countries that have formed from rocks other than the types required by the definition are being mined and sold as bentonite. Perhaps the best definition of bentonite as an industrial mineral is one given by R.E. Grim in a plenary lecture at the International Clay Conference (AIPEA) at Madrid, Spain, June 27, 1972. According to this redefinition, which will be used in this chapter, bentonite is a clay consisting essentially of smectite minerals (montmorillonite group of some usages), regardless of origin or occurrence. This definition solves the problem of the difference between the geologic and industrial usages of the term and overcomes the difficulty in assigning a name to smectite clay that formed from igneous rock other than ash, tuff, or glass, or those of sedimentary or uncertain origin. However, bentonite, when used with this meaning is still a rock term (consisting of more than one mineral), and it will not be possible to distinguish it from fuller's earth in many instances. One way of classifying bentonite is based on its swelling capacities when wet or added to water. Bentonite having sodium (Na+) as either the dominant or as an abundant exchangeable ion typically has very high swelling capacities and forms gel-like masses when added to water. Bentonite in which exchangeable calcium (Ca++) is more abundant than other ions has much lower swelling capacities than sodium varieties. Some calcium types swell little more than common clay, and most crumble into granular masses in water. Intermediate calcium-sodium bentonites, the so called mixed types, tend to swell moderately and to form gels of lesser volumes than equal masses of the sodium type bentonite. Because of the general relationship of swelling and exchangeable ion characteristics bentonite is commonly divided into the high swelling or sodium, low swelling or calcium, and moderate swelling or intermediate types. The term sub-bentonite (Davis et a]., 1940) is used inconsistently in industry for the low or moderate swelling varieties. The authors believe the use of this term should be discouraged because of its implication of low quality or low value and the lack of a mineralogical or use basis for it. In the United States bentonite is also classified by geographic location and the uses for which it is sold. Inasmuch as most of the low swelling calcium type occurs in states bordering the Gulf of Mexico, this variety is commonly called Southern bentonite. The largest high swelling sodium bentonite deposits and the major producing districts are in Wyoming and adjacent states. Therefore, this bentonite is commonly called the Wyoming or Western type. Such terms as drilling mud bentonite, foundry bond bentonite, and taconite bond bentonite relating directly to use are applied in marketing. Other terms including high and low yield bentonite, high and low gel bentonite, and high and low strength bentonite are also used to distinguish different grades. The varied classifications notwithstanding, bentonite occurs in so many different varieties that some cannot logically be classified according to any of the foregoing groupings. One of these types is hectorite, which is a high swelling lithium-bearing variety of smectite occurring mainly in California and adjacent states. It is, therefore, not a Wyoming type, and it occurs even farther west than the so called western bentonites. Others are bentonites having magnesium (Mg++) or hydrogen (H+) as the most abundant or dominant exchangeable ion. These types are neither sodium nor calcium varieties, and apparently some are low swelling, whereas others have rather high swelling capacities. Still another type of bentonite, the so-called potassium type, K-bentonite, or metabentonite, occurs in Ordovician and other Pa-

Jan 1, 1994

By J. D. Miller

"It is now possible to use 3D X-ray tomography analysis for plant-site characterization of coarse particles at a sampling rate of about 3 kg/min for particles which range in size from 150 mm to 1 mm at a voxel resolution of about 150 microns. This is quite a significant advance in X-ray tomography technology and should be useful for plant-site coarse particle characterization (size, shape, composition, density, texture, grain exposure, mineral liberation) with a response time of minutes after receiving the sample. Applications in the mineral industries are discussed including the coal industry, aggregate industry, metal mining and the processing of industrial minerals. INTRODUCTION Plant-site characterization of coarse particles at coal preparation plants, crushed stone/aggregate plants, and mineral processing plants is needed to improve plant capacity, product quality, and/or process efficiency. Not much on-line coarse particle characterization is done at these plants. Some limited information regarding particle size is obtained on-line from reflected light images using systems such as the OPSA, Split, and WipFrag analyzers. Even laboratory analysis of coarse particles has been difficult because of the large amount of sample required to insure statistical significance of the results. During the past decades laboratory 3D characterization of particles from energy and mineral resources by X-ray tomography has been demonstrated and used to good advantage [1, 2]. 3D X-ray tomographic analysis had its origin in the medical services industry; it is used to provide internal images of the human body and now has also been developed for non-medical applications [3]. Figure 1 shows a schematic diagram for the cone-beam geometry micro-CT system. In our case X-rays from a microfocus X-ray generator are partially attenuated by the sample (a packed bed of particles) that is made to rotate in equal steps in a full circle about a single axis of the particle sample. At each rotational position, the surviving X-ray photons are detected by a planar two-dimensional array (image intensifier) large enough to contain the shadow of the specimen. These two dimensional projection images are collected using conventional video technology. The video signal for each projection is then converted to a two-dimensional digital array by an image processing system. Finally, a three-dimensional image is reconstructed from the collected set of projection images. With the availability of automated high speed X-ray tomography [4] it now seems possible to do plant-site particle characterization at a sampling rate of about 3 kg/min for particles which range in size from 150 mm to 1 mm at a voxel resolution of about 150 microns. This is quite a significant advance in X-ray tomography technology and should be useful for plant-site particle characterization (size, shape, composition, density, texture, grain exposure, mineral liberation) with a response time of minutes after receiving the sample. Applications in the mineral industries are discussed including the coal industry, aggregate industry, metal mining, and the processing of industrial minerals"

Jan 1, 2016

By T. E. Wilson

An exploration bore core sample of coal ought to be reduced from its original cylindrical form to a particle size distribution and particle composition that reflects, insofar as possible, a process stream of? raw? coal it represents. Often, coal cores are reduced with a laboratory crushing machine, the product of which may not match the raw coal size distribution or size fraction composition. This study employs drop-shatter impact breakage followed by dry batch tumbling in a steel cylinder rotated about its transverse axis in order to characterize the core material in terms of first-order and zeroth-order breakage rate constants. These are indices of the propensity of the coal to degrade during excavation and handling. Initial drop-shatter and dry tumbling tests were done with synthetic cores, to reduce material variables and . conserve difficult-to-obtain coal cores.? Cores of three different coal beds --Illinois No.6, Upper Freeport, and Pocahontas No. 5 -were subjected to drop-shatter and dry batch tumbling tests to determine breakage response. Comparison of coal preparation plant feed with a crushed bore core and a bore core prepared by drop-shatter and tumbling (all from the same Illinois No.6 coal mining property) indicated that the size distribution and size fraction composition of the drop-shattered/tumbled core more closely resembled the plant feed than the crushed core.

Jan 1, 1998

By D. W. Mitchell

Never increase, reduce, or remove ventilation without unquestionable, compelling reasons. This rule applies every day as well as when fighting fire, attempting to find survivors, or recovering the mine. Right now in some mine a miner is adjusting a regulator in one place to get more air into another. The chances are the desired result will be achieved. Has the miner done a good thing? NO! Solving the immediate problem reinforces the belief he or she can do it again. That "again" might be, to give but one of many examples, the explosion in Greenwich No. 1 Mine. Robbing the proverbial Peter can be the prelude to disaster in a mine. Reducing the airflow is a common practice when fighting a mine fire. In fact, some people have been taught to do that at MSHA's academy. People who believe that to be proper must be people who never experienced a fire. To fight most fires you have to scramble to get enough air. An explosion demands totally different "thinking". If people are soon to go into the mine, DON'T adjust the ventilation. If teams are in the mine, each affected area must be explored or sealed before making any ventilation change.

Jan 1, 1993

By B. A. Slaker, T. Miller, M. M. Murphy

An underground limestone mine in eastern Ohio was experiencing significant floor heave and roof falls, attributed to high horizontal stresses. Areas of the mine showing floor heave were monitored with roof-to-floor extensometers and photogrammetry surveys to determine the rate and magnitude of heave. Extensometer data were recorded hourly at four locations across adjacent entries while photogrammetry surveys of the floor were performed at the same locations every two to five weeks. A final survey was performed using an I-Site 8200 laser scanner. Following instrumentation, floor heave up to 10.1 cm (4 in.) was measured by the extensometers, photogrammetric reconstructions and laser scanner over a six-month period. The extensometers were biased by the location where they were placed, failing to consistently capture the location and extent of floor heave and cracking. The photogrammetry surveys were not precise enough to capture small magnitude movements. Mining in the area was halted and within several months the floor movement and incidence of roof falls were significantly lessened.

Jan 1, 2018

By David M. Abbott

This paper is a companion to, and amplification of, the ?History? section of the 2014 version of the SME Guide for Reporting Exploration Results, Mineral Resources, and Mineral Reserves (SME Guide). The need for the careful examination and evaluation of mineral deposits has long been recognized. In the book De Re Metallica, Georgius Agricola noted, ?Moreover, a prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him? (1556, p.29). Agricola further stated, ?Now a miner, before he begins to mine the veins, must consider seven things, namely: the situation, the conditions, the water, the roads, the climate, the right of ownership and the neighbors? (1556, p. 30). The elements of Agricola?s seven things, much expanded, are incorporated into the 2014 SME Guide. As reflected in this quotation, veins were the primary concern of mining until 20th century technology permitted bulk mining techniques. The need for standardization of reserve descriptions arose along with the development of western mining in the United States and the concurrent development of mining engineering and mining geology as professions. By the turn of the century, debate about terminology of various classes of reserves was in full swing. Herbert Hoover noted in 1909 (p. 16-17), ?The old terms ?ore in sight? and ?profit in sight? have been of late years subject to much malediction on the part of engineers because these expressions have been so badly abused by the charlatans of mining in attempts to cover the flights of their imaginations. A large part of Volume I of the Institution of Mining and Metallurgy has been devoted to heaping infamy on these terms, yet not only have they preserved their places in professional nomenclature, but nothing has been found to supersede them. ?Some general term is required in daily practice to cover the available field of visible ore, and if the phrase ?ore in sight? be defined, it will be easier to teach the layman its proper use than to abolish it. In fact, substitutes are becoming as badly abused as the originals ever were. All convincing expressions will be misused by somebody.? Hoover (1909) noted that the common terms at the time were: ? Positive ore or ore developed: Ore exposed on four sides in blocks of a prescribed size. ? Ore blocked out: Ore exposed on three sides within a reasonable distance of each other. ? Probable ore or ore developing: Ore exposed on two sides, ? Possible ore or ore expectant: Ore in whole or in part below or beyond the range of vision. Hoover stated that these, and similar terms, overlapped and had the difficulty of failing to account properly for geologic variation in metal distribution beyond the exposed face. Certainly assuming extension of values along a vein is reasonable, but how far? Also, these definitions are for vein deposits, not all types of deposits are in veins. Hoover (1909, p. 19), therefore, defined the following terms. ? Proved ore: Ore where there is practically no risk in failure of continuity. ? Probable ore: Ore where there is some risk, yet warrantable justification for assumption of continuity. ? Prospective ore: Ore that cannot be included in the above classes, nor definitely known or stated in any terms of tonnage.

Feb 1, 2014

By Leonard W. III Joseph, William H. Buttermore

Noise control is an important consideration in the design and operation of coal preparation plants. It is essential to understand and control noise sources to provide a safe environment for operating personnel. The average noise exposure levels in a typical coal preparation plant generally range between 95 and 100 db. An operator should not be exposed to noise levels of this magnitude for more than 4 and 2 hr, respectively, according to MSHA (Mine Safety and Health Administration) regulations. The major noise sources in a coal preparation plant include noise from impacting the inside surfaces of steel chutes, vibrating screens, coal crushers, pumps, motors, fans, and blowers. The magnitude of noise varies considerably from one situation to another. NOISE EXPOSURE IN COAL PREPARATION PLANTS Noise regulations established by the Occupational Safety and Health and- ministration (OSHA) are accepted by MSHA relative to coal preparation plants. Fig. 14-43 shows a graph of the time of noise exposure in hours per day to which a worker can be exposed for each A-weighted sound level. According to this graph, a worker is permitted to spend 8 hr in a 90-db noise environment, but that time must be halved when the A-weighted sound level increases 5 db. The noise dosage a worker receives is determined by the ratio of the length of time the worker spends in a particular noise environment divided by the length of time he is permitted to spend in that environment. If the worker is exposed to several different sound levels, his total dosage would be the sum of each of the individual dosages. The equation for determining the dosage is: where C is the actual duration of exposure at a given steady state noise level and T is the noise exposure limit for the level present during the time C According to MSHA regulations, the dosage, D, should not exceed one (1) for any worker for a full day of work. As an example of typical plant noise levels, vibratory screens and crushers emanate noise levels in excess of 90 db at a distance of 3 ft (0.9 m) with no material flow. With material flow, noise level increases 1 to 10 db depending

Jan 1, 1991

By Jesus M. Rohena

Concrete pipes and small boxes have been installed by the jacking method. This paper will describe a recent project were large concrete boxes were installed by the jacking method. This project is in the city of Boston, MA. By now everyone in the USA knows something about this project. The project official name is The Central Artery/Tunnel Project (CA/T). This is the biggest public work project in the USA right now, with an estimated construction cost of 14 billions. The main objective of the CA/T project is to replace an existing artery built in the 1950s to increase capacity and safety. One section of the new artery will cross under several railroad tracks near the South Station. To construct the section of the new artery under these tracks, big concrete boxes were installed by the jacking method. The jacking method can be used to install pipes, small concrete boxes, and the CA/T project has demonstrated that big concrete road tunnel boxes can be installed by jacking.

Jan 1, 2003

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

6.1 INTRODUCTION A surface structure will suffer damage when the additional stresses induced by ground deformations associated with surface subsidence, plus the original stress introduced by construction de¬sign, exceed the strength of the structural elements. In this con¬text, there are two methods available for preventing and control¬ling surface structural damage: one is to strengthen the structure and the other is to design the mining operations such that ground deformations at the structure site can be reduced to an acceptable level. Mining operations include panel layout and mining tech¬niques. These methods are detailed in this chapter. It must be noted that most prevention/control methods men¬tioned in this chapter are used in the countries where the reference papers are cited. In the United States, the coal operators are not required to take those measures mentioned in this chapter. Some of the methods described in this chapter cannot be implemented with¬out changes in the current mining practice as permitted by laws. In addition cost of implementing those methods are not considered here. 6.2 PANEL LAYOUT As shown in Figs. 2.9, 2.10, and 2.11, permanent ground deformations in a subsidence basin mainly concentrate near the edges of the underground opening, and can be divided into four zones. A structure located in different zones will be subjected to different types and magnitudes of ground deformations. In laying out the panels, Table 5.1 and Figs. 2.9, 2.10, and 2.11 could be taken into consideration. Attempts could be made to avoid placing the structure on a location where the ground deformation to which that structure is sensitive is at its maximum. Therefore rational design of the panel is the simplest way to reduce structural defor¬mations. Panel design involves the determination of panel dimension, panel edge location, direction of face advance, and use of yield chain pillars. A. Panel Dimension Since longwalls in the US employ a multiple-entry system, where rows of chain pillars are left unmined, subsidence over those chain pillars is usually smaller. Therefore, whenever possi¬ble, the panel dimension could be designed such that a major structure or structures are over those unmined chain pillars, be¬tween adjacent panels, or some distance beyond both ends of the panels. At the center of the supercritical final subsidence basin, a structure will not be subjected to any final or permanent ground deformations. In order to create such a condition, the panel width must be such that the structure will be located beyond the major influence zone of the final subsidence basin, the minimum dimen¬sion of which must be: [ ] where L is the width or length of the final mined out gob, t is the width or length of the structure to be protected, h is mining depth and [ ] s is the angle of full subsidence. B. Panel Edge Location Wherever there is a permanent panel edge, there are large ground deformations induced on the surface on both sides of the permanent panel edge. Therefore whenever possible the panel di¬mension should be designed such that the permanent panel edges could be located in the areas with the least impacts. In terms of permanent edge location, it is best to eliminate any permanent panel edge under a structure or groups of structures. If this cannot be done, the panel should be lengthened to reduce the number of permanent panel edges, or narrower multiple panels advancing in the same direction in a staggered manner could be employed. If the structures are located in Zones II and III, the longer dimension of the structure must be parallel to the nearest perma¬nent edge (Fig. 6.1). But in Zone IV, the longer dimension should be tangential to the corner of the permanent panel edge. If the structure is inclined to the permanent panel edge, it will be sub¬jected to twisting and shearing. C. Direction of Face Advance The direction of face advance should be parallel to the long axis of the structure. But if the structure is to be located at or close to the center of the final subsidence basin, the direction of face advance should be perpendicular to the long axis of the structure. Careful choice of the direction of multiple face advance is the most effective way to reduce structural deformation and thus dam¬age. This applies the principle of overlapping and cancellations of ground deformations, due to multiple face advance, at the right time and at the right intensity, e.g., opposing tilts, concave and convex curvatures, tensile and compressive strains are induced simultaneously on the structure to be protected by two or more faces. D. Use of Yield Chain Pillars In US longwall panels there are generally two or three rows of stiff chain pillars between the panels. The combined width of the chain pillars ranges from 100 to 350 ft(30 to 107m). depending on mining depth. In general, surface movement above the chain pil¬lars after the panels on both sides have been extracted is much smaller, as compared to that in panel center. Thus in order to create critical or supercritical width of opening and eliminate sur¬face bumps over the chain pillars, yield chain pillars may be em¬ployed (Jarosz and Karmis, 1986). However if yield pillars are to be used, it must be designed such that it yields totally right after the panels on both sides have been extracted. Unfortunately cur¬rent yield pillar design techniques cannot predict when and how much it will yield. In summary, whenever possible attempts could be made to lay out the panel in such a way that surface structures are located above chain pillars between panels or above solid coal beyond both ends of the panels. In those areas the surface structures will most likely be unaffected, or if affected, the damage is so minor that no remedial measures are necessary. 6.3 CONTROLLED MINING TECHNIQUES Several mining techniques are available for reducing the sur¬face ground deformations of specific types. Regardless of tech-

Jan 1, 1992

By M. J. Sanzotti

This paper examines the potential for controlling longwall-induced subsidence by pneumatically backstowing the void created by mining with waste rock, and having the process scheduled as a unit operation of the mining activity. Based on a review of background literature, interviews with representatives of various mining companies, public-interest groups, and state and federal regulatory agencies, a hypothetical case-study evaluation of pneumatic stowing in a southwestern Pennsylvania mine site was conducted. The study indicated that current stowing technology cannot keep pace with the production potential of U.S. longwall systems. Further, at the case-study mine site, concomitant stowing would reduce subsidence by only 50% of that incurred during full longwall caving, the longwall coal production rate would decrease from 4000 tons per shift in the non-stowing case to 1500 tons in the stowing case, and a preliminary cost analysis reveals that pneumatic stowing would add $5.25 to $10.50 to the operating cost of producing a ton of coal at the case-study site.

Jan 1, 1995

By G. V. Henderson

Limestone and Dolomite quarries located near Salto-De-Pirapora, Arroia Grande Gaucho, Conde Francisco and Candioita probably represent the closest, major sources of high quality lime and cement grade carbonate rocks to the major population center of Sao Paulo Brazil. The nearest major city to most of the limestone - dolomite sources is Sorocaba and Palma. All of the mining properties visited during this study are located in the state of Rio Grande Do Sul at approximately -32 degrees south latitude and -52 degrees west longitude, southwest of the major port city of Porto Alegre.

Jan 1, 1981

By M. Jessop, V. O. Kofoed, R. Blanchard, A. Hughes

Willowstick has successfully employed a new Seismic Acoustic Resonance (SAR) method to improve seepage characterization through, beneath, and around dams. SAR is a passive seismic method that detects zones of higher permeability in the foundation and fill materials of a dam. Just as the ocean has tides, the earth’s crust experiences daily “Earth Tides” and is constantly in motion. Continual motion produces resonance signals that can be measured, interpreted, and modeled to identify zones of higher permeability within a dam and its foundation. The SAR results are analyzed in conjunction with the traditional Willowstick Method to better characterize seepage flow paths and patterns trough, beneath, or around a dam in three dimensions. When both methodologies, which use entirely different scientific principles, identify the same anomalous feature, a higher degree of confidence is gained in the results of the investigation. Willowstick has effectively utilized the SAR method on many successful dam seepage investigations. The two geophysical techniques when used in parallel have yielded complimentary results, with both methods providing beneficial information about seepage locations. This paper will detail seepage flow paths identified using both Willowstick and SAR methods for two case study tailings dams in Canada and the United States.

Feb 1, 2023

By Jr. Kirschner

An abandoned waste impoundment located within a portion of the Kellogg, Idaho Superfund site constitutes a field research area for studying the feasibility of recovering heavy metals in-situ from unsaturated mine and mill wastes. A prototype in-situ leaching cell has been evaluated using liquid-phase tracer tests and other hydro-geologic tests prior to introducing a lixiviant. The results of the tests suggest that: (1) the cell can be operated excursion-free with a low-density lixiviant at an injection/withdrawal rate of approximately 0.32 l/s; and (2) each hydro-geologic unit is highly heterogeneous at the different scales studied.

Jan 1, 1993

By Michael Murphy, Mark Van Dyke, VASU GANGRADE, Brent Slaker

Room-and-pillar mining in multi-level underground stone mines come with unique pillar stability issues. The pillar stability in these mines primarily depends on the thickness of interburden between mining levels and the staggering of pillars. NIOSH has previously established pillar design guidelines for shallow, flat-lying mines and single-level operations, but there is little guidance for ground control design in multiple-level stone mines. Therefore, to improve the overall understanding of ground control in these mines, a microseismic monitoring system has been installed at a multi-level underground stone mine in Tennessee with up to a 243-m overburden and a 7-m interburden thickness between levels. The microseismic system is comprised of nine uniaxial accelerometers and one triaxial accelerometer installed in the interburden. The seismic array is locally focused with all sensors installed within a 625 m2 area and is setup to monitor the seismicity around the formation of the pillar in the lower mining level. Data is collected over 11 months and comprises of over 1,000 high-confidence events that have been located in the study area comprised of post-blast activity. The event locations were identified using a 3D-velocity model, with an average 4-m location accuracy for this array calculated using the system data. Most observed seismicity was on the excavation boundary, both in the interburden and in the roof of the top level. At this stage of analysis, there are no significant rock failures with which to correlate seismicity, but event locations correlate well with presumed damage in the vicinity of blasts.

Apr 26, 2022

In the late 1980s and into the 1990s, the Mountain Pass Mine in California produced about 40 percent of the world?s rare earth elements. At the height of this production, the facility produced up to 54 L/s (850 gpm) of saltwater that was piped to offshore holding ponds where the water was evaporated. In 1998, following a series of waste water pipeline breaches, separations activities were suspended, reducing the Mountain Pass site to just the openpit mine and mill. The environmental concerns were addressed and the affected areas have since been remediated. However, in the years following the breaches, 97 percent of the world?s production of rare earth elements moved to China. By 2011, Molycorp, and the Mountain Pass Mine, had rebounded from the difficult times and were once again in a position to become a significant player in the rare earth industry.

Jan 1, 2011

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

"A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob. INTRODUCTION During a series of stakeholder meetings, a near unanimous concern was expressed related to maintenance of effective ventilation airflow on longwall faces. There was a strong interest expressed regarding the impacts of face length and caving characteristics on the ability to maintain adequate face airflow levels. This study seeks to understand and improve a mine operator’s ability to monitor and control ventilation and methane concentrations across the longwall face by assessing airflow variations in terms of roof caving characteristics and face length. National Institute for Occupational Safety and Health (NIOSH) researchers seek to identify flow paths of ventilation airflow on longwall panels with variations in roof caving characteristics and longwall face lengths. The project research aims to develop an understanding of the role of gas dynamics in variable broken rock, interactions with ventilation airflow and methane concentrations across the longwall face area. The research also addresses continuous ventilation monitoring along the shield line to provide early detection of gas exchanges between face and gob, and thus improve a mine operator’s ability to monitor and control ventilation and methane concentrations around the face. In the context of this paper, the longwall gob refers to the pillared area behind the shields. This work reports on results from one project task to conduct field based research using a tracer gas to describe face air and gob area gas movement in a bleederless longwall ventilation system that incorporated a back return."

Jan 1, 2017

By Howard J. Haselhuhn

"The effectiveness of reagent adsorption onto hematite ore particle surfaces is critical during beneficiation to promote effective selective flocculation and dispersion and increase iron oxide recovery. The relationship between aqueous calcium in the process water and the effectiveness of common iron ore dispersants has never before been studied. The nature of common dispersants was studied in the presence and absence of calcium in the process water. The settling behavior of hematite-rich iron ore at pH 11 was assessed in the presence of calcium and inorganic dispersants: sodium silicate, sodium tripolyphosphate (STPP), sodium hexametaphosphate (SHMP) and organic dispersant ethylenediamenetetraacetic acid (EDTA). It was found that inorganic dispersants are ineffective at a pH of 11 without activating the surface sites of the ore particles with calcium. Organic dispersants, however, were found to be effective with and without surface site activation.IntroductionThe United States produced 54 million metric tons of concentrated iron ore in 2011 (Jorgenson, 2013). Over 8 Mt were produced using a process known as selective flocculation and dispersion (CCI, 2011). The grade of this ore is slowly depleting, making it imperative that processing efficiency improves. To increase processing efficiency, a complete understanding of the effects of chemical reagents in the process must be acquired. This process relies heavily on dispersants to disperse iron oxides from gangue minerals in settling processes. The mechanism that these dispersants use to disperse the ore and its relationship to calcium in the process water has never been studied. The following extended abstract summarizes the relationship between aqueous calcium in process water and the effectiveness of common iron ore dispersants at dispersing hydrated hematite ore. These tests were carried out at a pH of 11, as this is a typical pH used to ensure dispersion in selective flocculation and dispersion processes."

Jan 1, 2015