Search Documents

By Harry H. Peek

Artesian pressures of unusual magnitude occur in the deeper aquifer units beneath a considerable part of southeastern North Carolina and extend into South Carolina. The high pressures were first observed in 1968 in wells near Wilmington that were drilled to "basement" rock and which were screened between depths of about 260 to 300 m (meters). The pressure was recognized by Peek and Heath1 as an anomalous geo-pressure and unrelated to recharge conditions in the region. Since 1973, much new information has been obtained on hydro-geologic conditions in the area and a preliminary report on the deep artesian pressures was published in 1975.2 Most of the basic information has been obtained from groundwater research stations constructed by the Groundwater Section of the North Carolina Department of Natural and Economic Resources as a part of Ground-water studies in the Coastal Plain Region. These stations consist of an exploratory well drilled to basement rock with wells completed in each principal aquifer unit to provide data on aquifer characterestics, water levels and water quality.

Jan 1, 1977

By G. Ferrara

During several years of operation in Europe, South Africa and other countries, the Tri-Flo has demonstrated to represent a substantial improvement of the dense medium dynamic separation systems. The reasons are: (1) high sharpness separation due to the multistage system and the application of new concepts in designing the regeneration circuit and controlling the medium rheology; (2) the possibility of performing two cuts at different densities using a since separation device and a single regeneration circuit. The paper discusses in detail the above mentioned points, with particular reference to the multistage technology, based on the circuit analysis theory, and to the control of the medium rheology based on recent work in the modelling, and simulation of the rheological behavior of dense suspensions.

Jan 1, 1993

By Daniel Lakovic

"Mining operations can create a negative environmental impact, especially when considering the tailings that are produced through the processing of ores. Tailings are finely grained residues that form sludges. The tailings are deposited into giant basins, or sludge ponds, where they create a burden on the environmentby limiting the use of processed water.Tailings are one of the most important environmental liabilities for mining operations because of their large proportion in relation to the ore mined — generally 90 to 98 percent. To get to the valuable minerals, mining companies must move large amounts of rock. The rock is ground and then treated, usually with the addition of chemical solutions and large amounts of water. The lower the concentration of the valuable resources, the greater the proportion of accumulated excavated material sludge.Sustainable tailings management requires responsible handling, making it one of the mining industry’s greatest challenges. The proper technology should include consistent control of the environmental risks and impacts, as well as a proper relationship with the communities that surround the mining operations.The tailings, which can remain partly contaminated with chemicals, are pumped into the large sludge basins, which are secured by earthworks. During the mining operations, the basins must be stable enough to withstand the pressure of the stored excavated material. The storage option is still used, but it has failed on occasion. And when it does, it increases the risks to the environment and binds the unused process water. The more complex the availability of fresh water required for industrial use and for human consumption and their economic activities — for example, farming and agriculture — the more complex the conflicts that have the potential to shut down mining operations. With modern separation technology solutions, it’s possible to process the sludge and recover the processed water. However, the responsible use of the water is critical. Therefore, mining companies must rely on technologies that allow for proper reclamation of the water, whether re-using in their own processes or treating it to return it to the environment."

Dec 1, 2018

By H. Askari-Nasab, B. Osei, K. Awuah-Offei

The U.S. coal mining industry consumes approximately 142 billion kWh/a of energy. The U.S. Department of Energy estimates that the industry’s annual energy consumption could be reduced by 49%. This constitutes nearly $3.7 billion of potential savings on coal production costs at 5.3¢/kWh of energy. Additionally, with climate change regulation on the horizon, any benefits from energy savings in the near future are compounded by associated reductions in CO2 emissions. Research indicates that operating conditions significantly affect energy efficiency. Modeling and simulation have been shown to be a cheap and reliable means of evaluating the effects of process interactions and operating conditions. The goal of this work was to apply stochastic process simulation to model the energy efficiency of a typical truck-and-shovel mining system and use the model to evaluate production strategies to improve energy efficiency. The research team conducted energy audits of truck-and-shovel overburden removal and used the results to develop regression models describing truck and shovel fuel consumption. The team then built a stochastic simulation model of the truck-and-shovel overburden removal operation and used it to assess a variety of improvement measures by simulation experimentation. Valid fuel consumption models for shovel loading and truck haulage have been formulated, based on the energy audit results. Valid stochastic process models of truck-and-shovel operations have been formulated to study energy efficiency. The following strategies, in decreasing order of impact, provide the most energy savings for truck-and-shovel overburden removal at the mine: (1) shorten haul roads, (2) increase shovel capacity and (3) increase shovel utilization through optimal truck matching. Additional data will be required to adequately describe operator effects on energy efficiency.

Jan 1, 2011

By Stephen Njoloma, Ivan Hee, Ravi Jain, Mina Shinouda

"INTRODUCTION DC Water’s First Street Tunnel (FST) is comprised of a collaborative effort between DC Water, DC Water’s Project Consultants Organization (PCO) led by Greeley & Hansen and McMillen Jacobs Associates and the design-build team of Skanska, Jay Dee, and Parsons Brinckerhoff. The fast-track project includes elements that were designed by the PCO and released for construction by DC Water prior to Notice to Proceed (NTP) and elements designed by the Design-Builder from 30% to released for construction after NTP. This required effective communication and technical coordination for integrated engineering and efficient construction. The project, constructed in an urban residential neighborhood, included innovative construction methods such as multiple location ground freezing, utilizing a centralized freeze plant, to minimize community impact. The means and methods chosen for cast-in-place shaft linings, precast segmental tunnel lining, microtunneling, sequential excavation method (SEM) adits and near surface elements reflected the immediate and sensitive surroundings, which varied by construction staging area (CSA). Technical aspects of the project, relative to the evolution from pre-bid to construction documents, are discussed along with modified designs to suit means and methods. SCOPE OF WORK In 2012, four major storm events swept through the District of Columbia and hit the Northeast Boundary sewer shed particularly hard with the neighborhood experiencing severe flooding. The extreme nature of the flooding, the damage to private property, and the health risks associated with exposure to sewage led to a multi-agency response and community calls for answers and action. The Mayor assembled a Task Force to evaluate a range of potential actions to address combined sewer flooding including engineering, regulatory, code revision, and management improvements. The Northeast Boundary Neighborhood Protection Project was the outcome of the Mayor’s Task Force; it is a three-step infrastructure initiative designed to offload the undersized sections of the existing collection system that serves the Northeast Boundary drainage area by implementing the McMillan Stormwater Storage Project, First Street Tunnel Project and the future Northeast Boundary Tunnel Project. Until the Northeast Boundary Tunnel Project is completed, the First Street Tunnel Project will add 8 million gallons of combined temporary sewer storage in a new tunnel under First Street NW to relieve undersized sewers that traverse the Bloomingdale neighborhood."

Jan 1, 2016

By C. J. Greet

Grinding with an electrochemically inert grinding media (i.e., high chrome white iron) shifts the pulp potentials to more oxidising conditions, increases the dissolved oxygen content and reduces the EDTA extractable iron concentration when compared with milling with electrochemically active grinding media (forged steel). These changes in pulp chemistry produce cleaner particle surfaces, reduce reagent consumption, and increase concentrate grades and recoveries. This paper presents a robust laboratory test program that not only demonstrates the changes in the pulp chemistry, but also provide an indication of the magnitude of the metallurgical improvements that are possible. While laboratory studies are interesting, the proof is in the pudding! So, the paper provides an overview of plant trials conducted at several porphyry copper operations around the world: Newmont’s Cadia and Red Chris Operations, as well as Evolution Mining’s Northparkes Operation. These successful plant trials clearly demonstrate that selection of the right grinding media alloy will yield savings in grinding media consumption and reagent consumption as well as increases in revenue through improved copper and gold recoveries. However, many of the porphyry copper mines on the Eastern Pacific are copper-molybdenum deposits. The paper presents laboratory test results for typical copper-molybdenum operations and extrapolate these numbers to what might be expected should a plant trial occur.

Feb 1, 2025

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By R. Kalra

The current paper looks at evaluating the merits of large geared mills versus gearless driven mills by evaluating the following factors: The capability of currently available systems in terms of power and mill diameter Efficiency in terms of overall electrical power consumed vs mechanical output power Capital cost Running costs Cooling requirements in terms of air versus water cooling Installation and delivery time World?s largest geared drive ? 2x8500kW ? Wushan, China (operating) Among the many reasons that geared drives on large SAG mills are not favoured, is due to not having an efficient variable speed drive option (60 to 80% critical speed), which is required for process reasons. As technological advances have occurred quite rapidly in recent years, this paper uses the latest data in applying these comparisons and attempts to dispel some of the myths regarding Slip Energy Recovery (SER) and variable frequency drive technology on twin pinion drive systems. Early attempts to provide load sharing on twin pinion drives used primitive electronics which have since been developed to eliminate the problems encountered in earlier attempts. In particular, torque pulsations between the twin motors have been overcome using a higher number of devices (pulses) and better electronics. With successful operation of 2 x 6.5MW (Phu Kham, Laos) and three 2 x 7MW units under manufacture (Pascu Lama) and a further 40 projects worldwide, energy efficient Hyper Synchronous SER drives are now mature and ready for use on 2 X 10MW dual drive mills. Speed variation required is in the range of +/- 15% of synchronous motor speeds. VVVF drive packages from ABB and Siemens are also available for 2 x 10MW in low and high speed options. Dual hydraulic inching drives provide a much safer and convenient operation with the added advantage of locked charge detection.

Feb 27, 2013

By Yuan Le, Dominic Reda, Vojtech Ernst Gall, Kurt Zeidler, Tomasz Kecerski

High Speed 2 (HS2) mandated that Building Information Modelling (BIM) processes be implemented during design and construction. Gall Zeidler Consultants (GZ) was responsible for developing the BIM Models for the portals, tunnels, and cross passages of the of the 16 km-long Chiltern twin-bore Tunnel. In addition, GZ developed the GBR for the Chiltern Tunnels and incorporated the relevant information into the Project’s BIM framework. This paper presents the implemented BIM framework, describes the modelling approach, and discusses the advantages and challenges of implementing BIM, particularly how BIM improved interface coordination and how BIM was used in feasibility assessments of different construction options.

Jun 13, 2023

By Atta Ur Rehman, Kwame Awuah‑Offei

This paper examines the effect of bucket geometry (cutting blade profile, floor profile, and blade thickness), speed, motor power output, and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scaled model of a load-haul-dump in full factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated to penetration and draft; muckpile particle size is positively correlated to penetration and negatively correlated to draft (p < 0.0014). The results show that buckets with a semi-spade cutting nose profile yield the highest penetration (mean 118.30 mm) followed by those with the spade (mean 108.88 mm), which also yield higher penetration than those straight blades (mean 95.19 mm). Bucket floor profile and blade thickness had no significant effect on penetration or draft. Also, we determined that increasing the speed and motor power output, simultaneously, can reduce bucket penetration. Thus, operators should not waste energy for no additional gain or even loss in bucket penetration. Also, the work finds speed and motor power output each combine with muckpile particle sizes to affect bucket penetration. This research furthers our understanding of the effectiveness of different bucket geometries in improving penetration and reducing draft for rubber tire loaders.

Oct 29, 2021

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and nonfatal injuries that occur in mining in the United States. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the U.S. Mine Safety and Health Administration (MSHA) from 2010 through 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84 percent involved the workers not using fall protection, fall protection not being provided or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment or working near highwalls. In most cases, a single, basic, corrective action — such as using fall protection — would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By James J. Komadina

INTRODUCTION Newmont Gold Company&apos;s Rain operations are located in Elko County, Nevada, approximately 9 miles southeast of the Town of Carlin.The property was submitted to Newmont Exploration Limited in 1979 and underwent development drilling over the course of the next four years, culminating in the completion of a project feasibility study in October 1986. Initial project scope included development of an open pit mine, an 815,000 DSTPY heap leach, a 572,000 DSTPY mill (Mill No. 3), and associated support facilities. Approval to proceed was given by Newmont Gold Company management in June 1987. Detailed engineering began in early July, followed immediately thereafter by procurement of major equipment components through various second hand sources. PROJECT DESIGN Keep It Simple In early August, Newmont Mining Corporation, parent company of Newmont Gold Company, became the takeover target of an "investor" group headed by T. Boone Pickens. Details of the ensuing events have been well documented by the press; suffice to say their impact on this project was material and required immediate flowsheet changes. Project design throughputs were increased to 1,000,000 DSTPY and 760,000 DSTPY for the heap leach and mill, respectively, in mid- September. These changes caused major project headaches as all general arrangement drawings had been approved and structural steel as well as concrete contracts were in place. Additionally, ground breaking was to commence in two weeks time! Rain project management assembled shortly after the announced changes, to devise an engineering and construction strategy capable of handling these new business conditions. The project had been justified using a gold price of $325 per ounce with a forecasted overall cash cost per ounce of $230. Hence, strict control of capital expenditures was necessary to maintain development economics. Mill start-up had also been moved forward one month, to August 1, 1988. To meet an already ambitious schedule, construction techniques needed to be simple and proven as most of the facilities were planned for erection during winter at a site with design criteria of -40F and 90 mile per hour winds. Perhaps the most critical factor requiring consideration was that of personnel. Newmont Gold&apos;s revised business plan called for corporate-wide production increases from 587,000 ounces per year in 1987, to 1,400,000 ounces by mid- 1989. Labor requirements were forecasted to grow from 900 employees to over 2,100. This fact, in combination with the rapid growth of Nevada&apos;s gold industry, led to the expectation that turnover of operating personnel would be extremely high. It was concluded that, to meet cost, time, and operational goals, the necessary strategy could be succinctly put - "Keep It Simple." Mining/Metallurgical Factors The Rain deposit consists of three interconnecting mineable shapes with host rocks ranging from 90%+ barite to a highly silicified jasperoid. Due to a limited number of mining faces in the first two years, in-pit blending

Jan 1, 1990

By C. B. Queja

Flexible synthetic membrane liners have become a standard facet to copper and gold heap leach pad design. While gold heap leach operations have utilized most types of synthetic liners, copper leach operations have commonly only been lined with polyethylene. The objective of this study was to determine if there are any chemical reasons why other synthetic membrane types could not be used to line a copper heap leach facility. With engineered consideration, the flexible membrane liner under the ore pile serves two purposes. The first provides a near impermeable boundary which aides greatly in the collection of the metal laden process solution. The second advantage to the flexible membrane is the almost non-permeable barrier to benefit increased environmental awareness that has led to an increase in solution containment technology. The Environmental Protection Agency (EPA) has developed a compatibility test for solutions and membrane liners. The EPA Method 9090 is intended for use in determining the chemical effects of a solution on the physical properties of the flexible membrane liner material intended to contain them. Data from these tests would assist in deciding whether a given liner material is acceptable for the intended application.

Jan 1, 1995

By Barbara J. Arnold

A coal&apos;s size distribution, clay content and moisture content can affect its handling behavior, but the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.&apos; s (formerly EPRI&apos; S) Coal Quality Development Center (CQOC) and at Iowa State University (ISU) will answer these questions as part of a four-year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of various coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that, while moisture content-is the most important variable, the amount of -325M (-0.044 mm) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1990

By Madan M. Singh

A new mining project can raise questions about what effect it will have on the community after it closes. Historically, little was done by communities to plan for and accommodate the changes in the economic infrastructure when a mine project is finished either after the ore runs out or if market conditions deteriorate and make it unprofitable. Projects that were underfunded were generally unable to withstand periodic market downturns. However, data in a recent study conducted by the Seidman Research Institute leads to the conclusion that, even when a mining project is terminated, there can be (and, in the specific case studied, is) a residual beneficial economic effect in the community, which lasts for a long period of time.

Jan 1, 2010

By Claus Becker

The new, 2.600 m long pipe under the river Elbe in Hamburg/Germany required for 2 traffic lanes, emergency lane and space for utilities a boring diameter of 14,20 m(46,6 ft). According the geology (glacial deposits consisting of clay, sand and marl, all containing big boulders) a Slurry-Shield with crusher was selected. With a minimum cover of 7 m and a maximum pressure of 5,6 bar extensive ground treatment was necessary to make the drive feasible. The machine contains a lot of new developments. The drive was finished in spring 2000 so all experiences can be reported. A special risk sharing contract avoided completely litigation.

Jan 1, 2001

By Kraig W. Grubaugh

Rapid growth in the rate of surface mining for coal has caused many states to increase the rigor and complexity of their surface mining codes. The promulgation of Federal surface mining standards may cause those states containing Federal land to amend their codes also. Presented is an up-to-date review of these codes with tabular summaries that divide the codes into operative functions. These summaries will be of use to new operators, multiple-state operators, and state officials. Suggestions are made for industrial efforts to present workable and acceptable amendments to these codes.

Jan 1, 1977

By MOHAMMED AMINE BELMI, ANAS DRIOUCH, ABDELAZIZ LAHMILI, LATIFA OUADIF

For many years, underground workings in the Bou Azzer mine have been challenged by geotechnical problems related to the serpentinite instability. The stage of evaluation of the compression potential is crucial to develop an appropriate drilling method and the choice of non-standard support. This research work presents a retro-analysis of serpentinite behavior in underground excavations at different depths, using a multi-approach method, based on several empirical and semi-empirical and theoretical-analytical methods, calibrated by the observational method. The analysis performed in this work reveals that underground excavations in Bouazzer East and Ait Hmane area would encounter compression problems that were recognized as the most serious from a depth of 300 m because of the effects of lithology and tectonics. Therefore, the Aghbar region has a slightly negligible compression potential. The compressive failure mechanism in this mine, depending on the mechanical strength, is started at induced stress of 9 MPa.

Nov 27, 2021

By P. G. Corser

A gold and silver open-pit mine located in northwestern Chile contracted ACZ in 1991-92 to assess the stability of their spent ore pile and to determine the cause and magnitude of cyanide contamination associated with leaching operations. The mine is a conventional open-pit located at an elevation of approximately 4,800 meters (m.) (15,744 feet). A spent ore pile is located approximately 2,000 m. southwest of the mine and approximately 1,000 m. northeast of the active pad and plant facilities. The pile was constructed on a gentle northwest slope dipping 12 to 13 degrees. The pile is bordered by a small river to the northwest and by a larger river to the northeast. Both rivers eventually flow into Bolivia. Heap leaching and processing commenced at the mine in 1988. Since 1988, nearly 6.0 million tons of ore at an average grade of 1.96 grams/ton (0.07 ounces/ton) of gold and 52 grams/ton (1.83 ounces/ton) of silver have been treated by cyanide heap leach methods with zinc (Merrill Crowe) precipitation. In approximately three years of operation, the mine has yielded more than 225,000 ounces of gold and over 1.5 million ounces of silver. Currently ore is agglomerated and hauled to the leach pad by truck and is top loaded to produce a 5-meter lift height. Four contiguous reusable (on/off) leaching pads were constructed with an asphalt layer above a carefully compacted sub-base of High Density Polyethylene (HDPE) liner and screened fines. Leach solution of pH 10-11 containing 1.2 to 1.5 gram/liter of cyanide is applied to the heap at a rate of 10 liter/hour/square meter for a total active application period of 30 days. Leached (spent) ore is transferred to the spent ore pile located approximately 1,000 meters to the northeast. The pile currently contains approximately 6 million tons of spent ore. The pile liner, which has been constructed over a prepared sub-grade consists of three geosynthetic layers (geotextile/flexible membrane liner/geotextile). Long term objectives include washing the pile to recover an additional 3 to 4 percent gold and silver.

Jan 1, 1993

By T. V. Johnson

The microstructural relationships in dolomitic fluxed taconite pellets were studied. The influence of basicity (in the range 0.75 to 2.1) and firing temperature (to 1340°C) on the grain structure, macrostructure, and mineralogical phase relationships are described. Extensive slag bonding of hematite grains begins at temperatures between 1220 and 1230°C, and results in fundamental changes in grain structure. Successive temperature increases result in little change in grain structure until 1340°C, when extensive coalescence of the hematite grains begins.&apos; Increasing flux additions have little effect on grain structure but greatly influence pore character. The compressive strength decreases with increasing flux addition, increases with increasing firing temperature, and is related to the macrostructure of the pellet. The compositions of the slag phases are represented on the CaO-Fe2O3-SiO2 phase diagram, and the compositional path of slag development is described.

Jan 1, 1980