Search Documents

By Wern-ping Chen

Technical and non-technical challenges exist in each mega infrastructure project. It?s no exception to the first US underground PPP Port of Miami Tunnel (POMT) project in Miami, FL. The POMT will connect two man-made islands, the Dodge and the Watson Islands, under the Biscayne Bay within highly porous limestone formation. Permeability as high as 0.1 cm/sec has been identified. Its 41-ft outside diameter, if constructed, is the largest precast segment lining in the US. Besides its geological and hydro geological challenges and risks, local community influence and impacts have controlled the fate of this project. This paper describes its tender design enhancements and the evolving of its slow advancement in resolving local community issues.

By A. Iannacchione

Longwall mining began within the Pittsburgh coalbed of Pennsylvania (PA) in the early 1970?s. Originally, longwall mine layouts were designed to fit within existing room-and-pillar operations, where panels were limited to that of typical production panels, e.g. a few hundred feet wide by a few thousand feet long. In these early designs, the gate entries were comprised of chain pillars similar to those found along main entry systems or within pillar recovery sections. The modern longwall mine has little in common with their 1970?s predecessors. Today the entire mine layout is designed around the longwall mining method. The longwall panels have grown to well over one thousand feet in width with lengths now measured in miles. In addition, development pillar sizes and shapes are matched to specific performance requirements.

Feb 27, 2013

By Roberto J. Guardia, Ted Lewtas, Peter Rasmussen, Klaus Winkler

As part of the Lake Fort Smith Water Supply Dam Enlargement project, located in northwest Arkansas, microtunneling methods were used to install two side-by-side,1.53m (60-in) inside-diameter steel pipes between the intake structure shaft and the lake. The 46.6 m- (153 ft-) and 41.7 m- (137 ft-) long tunnels were excavated in Pennsylvanian sedimentary bedrock ranging from coarse sandstone to siltstone and shale-like claystone. The intake tunnels were constructed 18.3 m (60 ft) below lake level from the dry shaft. Special installation methods and procedures described herein were used to complete the lake taps. Installation difficulties that caused minor delays are also reviewed. After the excavation of the Intake shaft was completed, the two lake taps were installed in approximately ten weeks with the same microtunneling machine.

Jan 1, 2005

By J. B. Hadaway

The current limit to power transmission for grinding mills through one mill pinion is approximately 7,500kW. Above this power rating either twin pinion arrangements or Gearless drives are required. The SMTP concept was developed to overcome this limitation by using two pinions with a single large drive motor. The SMTP mill drive offers major advantages in capital cost and greatly simplifies plant layouts, while using an innovative adaptation of industry-proven single helical gearing. Through the use of a single motor, provision of variable speed drive is greatly simplified. The SMTP can also be used for significant power upgrades on existing mills.

Jan 1, 2001

By D. A. Norrgran, J. A. Wernham, D. E. Walsh

A qualitative test program was sponsored jointly by the University of Alaska and Eriez Magnetics, in order to study placer gold nugget recovery using an eddy-current separator. Various gold nuggets from Alaska, ranging from 6.4 mm to 63.5 mm in size, were tested. All testing was performed using an Eriez Laboratory ESC, Model REA, fitted with 2000 gauss, surface field strength magnetic rotor. The belt speed was set to 91 meters per minute and the rotor speed was set to 2500 rpm in the forward direction. The splitter was adjusted to just reject the largest pieces of rock that measured an average 76 mm x102 mm x 127 mm. Based on the results of this limited test work, it can be recommended to placer gold mine operators, that Eriez Magnetics ECS technology is a viable and practical concentration technology for coarse gold recovery. Silver and platinum were also tested.

Jan 1, 2003

By Moussa Wone

The Washington, DC Water and Sewer Authority (WASA) has implemented facility planning for the Anacostia River Projects portion of a program to bring its Combined Sewer System (CSO) into compliance with federal water quality regulations by 2025. The program includes approximately 19 kilometers (12 miles) of deep CSO storage/conveyance and flood relief soft ground tunnels, construction, vortex drop, overflow, maintenance and air release shafts, as well as near surface diversion structures and conveyances. The Project encompasses major technical and non-technical challenges including completion under a federal consent decree schedule, construction within the confines of heavily developed urban areas, difficult ground conditions, major infrastructure crossings, and close coordination with several major public agencies. This paper discusses the planning stage considerations related to the geotechnical investigation program, discusses obstructions that influenced alignment selection, and provides two examples of preliminary estimates of settlement induced ground movement due to the tunnel and shaft construction.

Jan 1, 2008

The safety of personnel is the most important matter during a mine fire. However, there is not enough research on a case when a fire occurs near a shaft and the behavior of the fire gas is not well understood. Therefore, a series of experimental study using a scaled ventilation circuit model was carried out. The behavior of ventilation air during a mine fire near a shaft was investigated. The model consists of two vertical shafts, three horizontal ducts connecting the shafts and an exhaust fan from the shaft bottom. The cross section of the shaft and duct is a square of 200×200mm. The height of the shafts is 3400mm. The length of the ducts is 1540mm. The lower duct is set at the same level as the shaft bottom. The middle and upper duct are set at 750mm and 1760mm above the shaft bottom respectively. The airflow rates through the ducts can be adjusted by regulators installed in each duct. The behavior of the fire gas was measured by anemometer, thermometer, and visualized using laser light .The air was ventilated downward in both shafts before the initiation of the fire. Some amount of fire gas of high temperature rose upward gradually along the shaft wall regardless of the downward ventilation after the initiation of the fire. Then the direction of main ventilation air suddenly reversed upward in the shaft. The direction of ventilation reversed in many places in the model and the fire gas reached even the part not anticipated.

Jan 1, 2009

By Faruk Oksuz, Clay Haynes, Miguel Sanchez, Patrick Finn, Roger J. Maurer

The Milwaukee Metropolitan Sewerage District’s (MMSD)’s challenges of basement flooding and wet weather sewer overflows are being creatively addressed with the Northwest Side Relief Sewer tunnel. The $132 million, 20-foot diameter, and37,740 feet long conveyance and storage tunnel excavation in dolomite at depths reaching 165 feet below ground surface has been successfully completed within13 months in April 2004. This paper includes Owner’s perspective on the overall project, and the design and construction details by the Designer and the Contractor. The project contract documents included a comprehensive Geotechnical Data Report and the Geotechnical Baseline Report.

Jan 1, 2005

By C. R. Copeland

Airborne dust emission standards are receiving growing attention. This trend is motivated by significant health studies that have shown adverse health effects due to exposure to dust. Currently, the air quality standards are not specific to particles in the nanoparticulate range (<1,000 nm). However, as our understanding of health related matters increases, it is very likely that nanoparticulate standards will be adopted. It was previously believed that typical comminution and material-handling practices could not result in airborne nanoparticulates. However, experimental studies using air monitoring and SEM have verified the presence of nanoparticulates in the air as a result of comminution and material handling. This means that emerging nanoparticulate air quality standards are a real possibility for industrial operations. With this emerging problem facing the minerals industry, effective suppression methods for nanoparticulates should be explored. Systematic studies have indicated that nanoparticulates from silica can be suppressed utilizing hygroscopic reagents such as calcium chloride. This reagent was as much as 93% more effective than water in suppressing silica nanoparticulates.

Jan 1, 2007

By G. W. Bonnell, D. A. Young, D. G. Genter

Through 1996 and 1997, CANMET and the Cape Breton Development Corporation (CBDC) conducted a project to study the Phalen Mine’s 7 East longwall ventilation network to help determine methane emission patterns that were having a negative impact on coal production. Increased methane emissions were primarily related to mining depth and were also affected by the influence of a large sandstone body located above the worked seam. The research included the installation of tube bundle systems to monitor waste (gob) methane and pressure differentials. The focus of this paper is on the novel use of tracer gas techniques that helped shed light on the performance of the ventilation system and in determining the methane migration paths in the waste.

Jan 1, 2001

By James F. Kvitkovich, George V. Weisdack

Longwall mining techniques were introduced into U.S. bituminous coal mining operations in the early 1960s. These techniques were gradually adopted by many mines during the 1970s. By 1983, considered to be the peak of the longwall mine census, there were 118 active longwall faces in 79 coal mines throughout the United States. Beginning in 1984, longwall faces began a decline in numbers that has continued to the present day (Fig. 1). The geographic distribution of longwall faces today is shown in Fig.2 according to region. A breakdown of recent longwall mine production by region is shown in Table 1. An approximate breakdown of present longwall face installations by product (metallurgical and steam) is shown in Table 2.

Jan 1, 2005

By C. Guan

Since it was patented in 1942, the Crago process with fatty acid rougher flotation followed by deoiling and amine cleaner flotation has become the standard for phosphate flotation in Florida and North Carolina. This paper outlines the basic fundamentals involved in this proven technology. Included are the mineralogy of the flotation feed, the solution chemistry and the interfacial phenomena. The process variables affecting the performance of this technology are also discussed.

Jan 1, 2009

By Ed Cope

The newly discovered South Arturo deposit is a Carlin-type, breccia-hosted, oxide gold deposit located on the Dee Mine property at the north end of the Carlin Trend in Nevada. The Dee Gold Mine was discovered in 1981 by Dee Delamar, a Cordex geologist. The property was put into production by Rayrock Mines in 1984. During its 16-year mine life, the Dee Mine produced about 18.6 t (600,000 oz) of gold from oxide ore at an average production rate of about 1.24 to 1.55 t/a (40,000 to 50,000 oz/year). In October 1997, Bar-rick Gold Exploration acquired the right to earn a 60-percent interest in the Dee property from Dee Gold Mines through an exploration farm-out agreement. Barrick Gold Exploration began exploration activities on the property in 1998 and vested in its 60 percent operating interest in 2004. However, the discovery hole at South Arturo was not drilled until July 2005 from atop the historic mine dumps located 300 m (985 ft) south of the Dee openpit. The discovery hole (BD-72) encountered a cumulative 75.6 m (248 ft) of oxide mineralization grading 1.9 g/t (0.055 oz/st) gold beneath 260 m (855 ft) of dump material and post mineral Tertiary Carlin Formation volcanic and sedimentary rocks. Oxidation within the deposit extends to depths greater than 610 m (2,000 ft). The deposit has passed the prefeasibility test and is presently in the feasibility stage. Exploration is on-going to enhance or enlarge the known deposit. The current resource for the deposit stands at 40.4 t (1.3 million oz) of gold. The South Arturo discovery is an example of an historic mining property yielding a new discovery through the diligent application of area selection criteria of the model type and persevering when early results were generally negative. Barrick?s original exploration pro-grams on the property were focused on the discovery of deep, high-grade sulfide deposits that would likely be mined by underground methods. As it turns out, South Arturo is mostly oxidized and will be amenable to mining by openpit methods

Jan 1, 2008

In this study, a 3D model of the shovel motion based multi-body system dynamics in the Automatic Dynamic Analysis of Mechanical Systems (ADAMS) environment was developed. The kinematics model of the shovel was modeled as a multi-body system, which comprises the lower, upper, and the attachment mechanisms. The Euler-Lagrangian equations were employed as the computational framework to describe the dynamic behavior of the model. A virtual prototype of the shovel was built in the ADAMS software environment. This environment allows the visualization of a 3D motion of the general mechanical system and the prediction of interference of the moving components of the shovel. The numerical analysis and animation of digging, swinging and dumping motions for the shovel were performed. The superimposed display of the deployment for the shovel in three phases allows a detailed examination of the dynamic interference among assembly components. This research provides a solid foundation for further shovel dynamics performance studies. Keywords: Shovel, Spatial Kinematics, Virtual Prototype, Visualization

Jan 1, 2009

The technical parametrization of reserves is a technique which has made an important contribution to the definition and the calculation of optimal mining projects. Its applications to a new open-pit optimization program have already been presented in various papers (François-Bongarçon and Maréchal (1976); François-Bongarçon and Guibal (1981)). The present paper gives a brief description of the general problem of parametrizing reserves before going into the details of the practical algorithms used in two typical cases, i.e. open-pit mining and mining between hanging wall and foot wall.

Jan 1, 1982

By James L. Poole

The gold and silver markets from the late 1960&apos;s to the present are reviewed and the outlook for these metals in the 1980&apos;s is presented. Included in this discussion is a summary of the basic supply and demand balance for gold and silver since the mid-1960&apos;s. an explanation of the price formation for the metals, some of the relationships between the prices of these metals and selected economic parameters, and how these factors affect the outlook.

Jan 1, 1981

By N. Ward

The Gualcamayo Mine is located in the Andes Mountains north of San Juan, Argentina (Figure 1). A property of Yamana Gold Inc, it declared commercial production in July 2009 and has a total mineral reserve and resource base of approximately 88,000 kg of gold. Crushing operations for the open-pit mine are located in a 13,500 m3 underground cavern with a ceiling height of 22 m. More than 3,600 m of tunnels are used to access the cavern and convey the ore. The Project as described in this paper relates to the design and construction of the Main Cavern, Conveyor System Exit Tunnel, the Mechanical System Access Tunnels, and two 4.20 m diameter shafts (Ore Pass #1 and Ore Pass #2) as shown in Figure 2. [ ] Preliminary engineering for the Project was performed by Hatch Chile. Rizzo Associates Argentina, S.A., a division of Paul C. Rizzo Associates, Inc (Rizzo) was contracted to provide geomechanical and geotechnical support for the construction of the access tunnel system and geomechanical design and construction supervision for the cavern and shafts.

Jan 1, 2011

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and thus deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the go band to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Feb 27, 2013

By Steve Kral

For the past several years, copper producers have faced a tough business climate. Nagging low prices forced many them to reduce their production and make other drastic cutbacks just to breakeven. And sometimes even that did not work. But, like other downturns in the industry, this latest dismal copper market allowed technology to make further inroads into mining and processing operations. Now that the copper market appears to be making a turn for the better, those years spent investing in technology by equipment manufacturers and forward-thinking mining companies should begin paying off.

Jan 1, 2004

By John McDonald, Peter C. Raleigh, Christopher Dishlip

This paper will discuss how the construction management team and the contractor working together on the City of Los Angeles, North East Interceptor Sewer project, managed information on a daily basis. Data was synthesized from various sources including: inspection, survey, instrumentation, laboratory and the tunnel boring machine data logger systems to produce state-of-the-art reports and graphics which will become industry standard. Special emphasis is placed on how the data is managed and interpreted in a clear and objective manner, permitting the tunneling processes to be carefully monitored and suggesting appropriate action to be taken by the construction management team and contractor.

Jan 1, 2005