Search Documents

By I. McDougall

The matte/slag tidal zone in a nickel-copper-iron-sulphide matte smelting furnace is subject to severe process conditions that can lead to premature failure of the lining. The MgO-FeO-SiO2 slag is aggressive to refractory bricks, while the Ni-Cu-Fe-S matte is aggressive to water-cooled copper cooling elements, and can penetrate and sulphidize refractory bricks. A novel approach to the lining design was taken at a PGM smelting furnace, where an indirectly-cooled graphite ring was applied in the matte/slag tidal zone, with refractory bricks on the hot face. The graphite was cooled by the copper cooling elements in the slag zone, obviating the need for copper cooling elements in the tidal zone. In this paper the effectiveness of different lining designs utilizing varying degrees of cooling in the slag zone and slag/matte tidal zones is compared. In comparison to water-cooled copper in various configurations, cooled graphite shows promise as an indirect refractory cooling system in the tidal zone area of furnaces. Keywords PGM smelting, graphite, refractory lining, copper cooling elements, submerged arc furnace.

Aug 1, 2013

By V. Tathavadkar

Worldwide TiO2is extracted from natural ilmenite, rutile, and anatase minerals via the sulphateand chloride processes. The sulphate process generates large volumes of less toxic wastes, whereas the chloride process, including the ilmenite-chloride process of DuPont, yields much lower volume of wastes, which are highly toxic and hazardous. The treatment and disposal of such hazardous chloride wastes is both expensive and difficult in terms of long-term monitoring. Besides the waste management and disposal, there is also a shortage of high-grade titanium dioxide minerals in nature, which consequently yields much larger tonnages of sulphate and chloride wastes. In the present investigation we report the results of an alternative titaniferous mineral beneficiation process based on soda ash roasting of minerals. Compared to the conventional processes for beneficiation of TiO2- ores, the alkali roasting of titaniferous offers several advantages including the zero process wastes. In the soda ash roasting process, the mineral is mixed with sodium carbonate and heated above 1023 K in air. The oxidative roasting of ores yields several complex alkali compounds, some of which produce a liquid mixture above 1123 K. In this paper, we have attempted to characterize the composition and physical chemistry of alkali-rich liquid phase. The phase equilibria in the Ti-(M:Fe)-Na-O system are evaluated and compared with the phases formed as a result of roasting reaction. The experimental results revealed that the composition of complex alkali liquid at the reaction interface plays an important role in determining the transport of O2-ions and decomposition of ilmenite. The roles of the crystal structure of mineral phases and their energetics are also emphasized in controlling their decomposition during alkali roasting. The presence of molten alkali in controlling the partitioning of water-soluble alkali salts and insoluble sodium titanate is also explained. Keywords: ilmenite, anatase, alkali roasting, phase equilibria.

Jan 1, 2004

By N. Ogbonna

A mathematical model for bioleaching at the agglomerate scale is developed. The agglomerate is defined as a unit volume of a heap which contains a solid phase (a size distribution of ore particles), a liquid phase (stagnant and flowing leaching solution) and a gas phase (flowing air and air pockets). Leaching at the level of an ore particle is modelled using a diffusion-reaction equation, and oxidation by attached and detached microbes is treated separately. With the aid of the mathematical model, the effect of particle size distribution on the bioleaching of an ore containing a mixture of chalcocite and pyrite, and a culture of iron oxidizers, is investigated.

Jan 1, 2006

By A. Varadarajan, M. Hashemi, K. G. Sharma

Quartz mica schist collected from Nathpa-Jhakri Hydropower Project, Himachal Pradesh, North India is tested under triaxial loading using a servo-controlled loading system. Complete stress-strain-volume change behaviour including post peak softening behaviour of the samples, are presented. Strength and deformation parameters are given. Quarz mica schist, der von Nathpa Jhakri Hydropower Projekt, Himachal Pradesh gesammelt wird, wird Nördlich Indien unter triaxial geprüft, der von Gebrauch eines servo kontrollierten Ladesystems beladung. Vollständiges Spannung-Spannung-Band Änderung Verhalten Postens Spitze Erweichung Verhaltens der Proben, wird überreicht. Kraft und Verformung Parameter werden gegeben. Mica à quartz schist recueilli du Projet de Hydropower de Nathpa Jhakri, Himachal Pradesh, l'Inde du nord est essayé sous l'utilisation de chargement de triaxial un système chargeant servo réglé. La tension complète-la tension-comportement de changement de volume y compris la poste sommet amollir le comportement des échantillons, sont présenté. Les paramètres de force et déformation sont donnés.

Jan 1, 2003

By B. Samanta

LHD (load haul dumper) is now used as a loading machine for intermediate mechanization in underground coal mining. For survival in the intense competition in the global business environment in recent years it is essential that LHD machine should be reliable and maintained effectively and efficiently. This paper seeks to study the reliability, availability and maintainability (RAM)of an LHD machine with failure and repair data by Markov modelling. The constraints and reasons for machine unavailability are outlined. The reliability and maintainability of an LHD and its subsystems are evaluated. Possible modification or design alternatives are highlighted. Reliability and maintainability of an LHD system are disappointing. There is room to take decisions on optimal maintenance planning and machine improvement from this analysis. Keywords: reliability, availability, maintainability, Markov model, LHD

Jan 1, 2004

By Y. Nakata, K. Nagata

Plasma is partially ionized gas composed of ions, electrons and activated elements at high temperature. Some flying ash from incinerated municipal waste is melted to become glass by a transfer-type arc plasma furnace. As the glass is ionic silicate, when an electric current passes through anode to cathode, ions in molten slag electrochemically react with electron in plasma at the surface of molten slag. In case of molten Na2O-SiO2, sodium ions in the molten slag carry electric current and SiO2are reduced to evaporate as SiO gas by electron in plasma. The cases of Ag+in NaNO3-KNO3molten salt and Fe2+in FeO-SiO2slag were examined. The amount of cathodic reaction is larger than that of anodic reaction and not apparently according to the Faraday?s law on the electrochemical reactions.

Jan 1, 2004

By J. N. Van der Merwe

The data base of failed pillar cases as used by Salamon and Munro (1967) in their original analysis to determine the strength of coal pillars empirically, has been updated for this study. It is shown that the Vaal Basin and Klip River coal fields exhibit similar behaviour that differs from the failures in other areas, i.e. failure at high safety factors within a short period of time. Those collapse cases have been omitted from the new data base. Failures in the other areas that occurred after 1967 have been added. Using a technique to minimize the area of overlap between the populations of safety factors of failed and intact pillar cases, the new data base was re-analysed in conjunction with the original Salamon-Munro data base of intact pillar cases, from which the cases in the areas of weak coal were likewise eliminated. It was found that a linear formula reduced the overlap area by22%. The new formula predicts higher strength for pillars with a width-to-height ratio greater than approximately 2.0 to 3.0 and a lower strength for smaller pillars. It was also found that in order to obtain the same relative measure of stability as with the Salamon-Munro formula, the strength constant in the new formula should be within a range of 2.8 to 3.5 MPa. For most current South African coal mining conditions, using the new formula for pillar strength will result in leaving smaller pillars without sacrificing stability. The reason for this is that the Salamon-Munro formula under-estimated the strength of larger pillars and over-estimated the strength of smaller pillars. The new formula will thus result in improved reserve utilization without sacrificing stability.

Jan 1, 2003

By J. Nell

An overview is given of the matte melting process used for the beneficiation of South African Platinum Group Metal (PGM) ores. Most producers use six-electrode furnaces to melt the concentrate and Pierce Smith converters to oxidize excess iron sulphide from the furnace matte. Concentrates from two reef-types (the so-called Merensky and UG-2 reefs) dominate the feedstock supply. Concentrate from the Merensky reef is low in chromium and do not pose significant melting problems. Concentrates from the UG-2 reef contain much higher levels of chromium, which results in the formation of chromium-rich spinels during melting. This is attributed to the low solubility of chromium in furnace slag under typical operating conditions (an oxygen partial pressure of 10-8-10-9bar at temperatures of 1550°C to 1600°C). During the converting process care is needed to avoid excessively oxidizing conditions, which result in cobalt, nickel and copper losses to the slag. High nickel losses result in the formation ofFe2NiO4(trevorite), which often forms solid solutions with FeCr2O4and Fe3O4. In future, the main challenge in the processing of South African PGM ores will be to cope with ever increasing levels of chromium in the concentrate. A short-term solution to the problem would be to melt the concentrate under slightly reducing conditions to promote the formation of CrO, which is more soluble in the slag than Cr2O3. A longer-term solution to the problem would be to abandon the current matte-smelting process in favour of an alloy-based process, which would offer total flexibility with respect to the amount of chromium that can be tolerated in the feed. Key words: Merensky, UG-2, furnace, slag, matte, converting, spinel, chromium.

Jan 1, 2004

By M. Moys

The use of temperature measurements for unusual applications in the analysis and control of column flotation and milling is discussed. This is followed by a review of some of the authors current research in the application of the discrete element method to the modelling of particulate processes, specifically milling, fluidized beds and chute flow.

Jan 1, 2005

By C. Maree

Paper written on project work carried out in partial fulfilment of B. Eng (Chem. Eng.) This paper describes the development and use of a process simulator to optimize gypsum recovery at Afmine, a small plant near Yzerfontein on the South African West Coast. The simulator consisted of models of the major plant equipment, viz. hydrocyclones, surge bins, settling tanks, a primary sieve and a dewatering screen. Experimental data suggested that the equipment could be modelled satisfactorily from data published in the open literature. Simulation studies have indicated that gypsum losses on the plant could be reduced substantially by means of some relatively minor modifications to the plant layout. Moreover, sensitivity analyses of the plant have indicated that optimization of the settling tanks should receive priority over the other process units.

Jan 1, 2005

In surface mining operations, ultra-heavy trucks operate on haul road networks which are typically from 10?40 km in length. These road networks are often not optimally designed and maintained and as a result, identifying and remediating road functional defects is problematic. Most surface mine operators agree good roads are desirable, but find it difficult to translate this into an effective road maintenance system. This paper presents a haul road maintenance management system which utilizes an assessment of rolling resistance based on a functional performance evaluation of a haul road, together with mine haul truck operating cost models to derive the optimal frequency of road maintenance. A typical application is presented which illustrates the potential of the technique to manage maintenance as and where needed with resultant reduction in total road user costs and an improvement in service provided for the road user. Keywords: Haul road, surface mining, road maintenance, transportation, pavement design

Jan 1, 2003

By Y. He

The nature of the density distribution in a gas-solid phase fluidized bed for dry coal separation is an important factor in influencing the performance. However, during coal processing, fine slime would mix with dense medium of magnetite powder and accumulate in the bed, and its influence will affect the density of the bed. The mathematical model of the density distribution with fine slime behaviour was studied in an experimental laboratory system. The functional relationship between the density of the air dense medium fluidized bed and the coal slime content were fitted, applying the principle of least-squares method with damping factors. With the model, by analysing the trial testing data, the mechanism of the density distribution of the bed was studied and applied to a coal separation test with a pilot scale separator. Keywords: dry coal separation, gas-solid phase, model fitting.

Jan 1, 2002

By B. M. Loftus

An investigation into the use of impinging stream (jet) reactors for the leaching of a free milling ore produced an increase in gold recovery by 10% while decreasing leaching time by up to 90%.Tests on refractory ores demonstrate no apparent improvement in recovery. However, leaching kinetics are dramatically increased when these ores are subjected to jet reaction prior to agitation.

Jan 1, 1997

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2013

By D. J. Burger

This paper will highlight the system components of a successful underground mining automation project recently launched at DeBeers Finsch Mine. It will also show that integration of short-term mine planning with other upstream and downstream mining processes in the extraction of kimberlite ore from a block cave is not just critical to the future sustainability of this underground mining operation but also for profitability and cost-effectiveness. This paper will discuss the information data flow required from the mine-planning process through to production for underground block cave mining. The benefits associated with this type of integrated mine planning and automation system will be highlighted.

Jan 1, 2006

By M. M. Manamela

Paper written on project work carried out at the University of Pretoria in partial fulfilment of the requirements of the B Tech degree at the Tshwane University of Technology This work tested whether ore particle size affects the carbon-based pre-reduction of titaniferous magnetite. Pre-reduction is performed at a temperature of some 1100°C in a rotary kiln, in the Highveld Steel process. Laboratory isothermal reduction measurements were performed with ore-coal mixtures at this temperature, to test the effect of ore particle size. The results show that size does limit the degree of reduction for particles larger than 15 mm.

Jan 1, 2005

By M. J. Lukhele

Paper written on project work carried out in partial fulfilment of B. Tech (Mining Engineering) degree A number of high wall mining methods were developed over the years to mine coal reserves exposed on the high walls created during surface mining. The auger mining system was initially developed in the early 1940s in the United States of America. High wall mining is a method of recovering coal from seam exposed either by mechanical excavation methods or natural erosions. This is usually associated with strip-mining (opencast) where the stripping ratio is high and uneconomical to mine using the opencast mining method. This paper discusses the surface auger mining as deployed at Rietspruit Mine Services Proprietary Limited.

Jan 1, 2002

By P. Dennis, T. Pieters, A. De Kievit, S. Ganguly

TEMCO has been producing manganese ferroalloys in submerged arc electric furnaces for over 40 years. The furnace linings all along have been of conventional insulation type until 2001 when a freeze lining of UCAR concept was installed for a 20 MW Furnace. Continuous improvement of furnace lining performance has been a key component in improving the business competitiveness of TEMCO. The expected minimum campaign life of the freeze lining is fifteen years as compared to the ten years of the conventional linings. The success of the freeze lining is very critical to the quanta and direction of heat flow through the lining that control the freeze protection. Under freeze protection can lead to reduced lining life and over freeze protection, on the other hand, can lead to operating difficulties and loss of smelting efficiency. It was, therefore, necessary to develop a computer based system to monitor and control the freeze protection. The computer based monitoring and control system uses the basic principles of heat transfer, activeX object and heat flux from dual thermocouples and that is reviewed.

Jan 1, 2004

By T. Plikas, L. H. Gunnewiek, L. Oshinowo

Electric furnace smelting is one of the principal unit operations for ferroalloy production, and increased process intensity, improved availability, minimal maintenance and a longer campaign life are common objectives for electric furnace operation in order to obtain favourable economics of production. Furnace designers have continued to develop innovative solutions that have allowed these objectives to be realised, e.g., furnace cooling systems, and numerical modelling plays a key role in the design process. Enhanced understanding of the energy transfer process in the furnace and the ability to develop, evaluate and optimise components of the crucible design to match process requirements are the key motivators for modelling. This paper provides an overview of recent applications of numerical modelling to the design of electric furnaces. The aim is to illustrate what can be done, and identify areas where further work is needed in this field. Examples include furnace bath modelling, crucible cooling system design, taphole design, baking of Soderberg electrodes, off-gas systems, and fume control and building ventilation. It is argued that the trend is for numerical models to become more encompassing while at the same time more accessible, and therefore further improvements in furnace design will be realised with continued and well validated modelling efforts.

Jan 1, 2004

By E. T. Boshoff

Paper written on project work carried out in partial fulfilment of B. Eng. (Metallurgical Engineering) The weathering of kimberlite can be accelerated with cations in solution if swelling of the kimberlite occurs in contact with the weathering medium. The type and amount of swelling clays present, along with the surface charge and cation valence, determine the degree of swelling that can occur. Crystalline swelling occurs by the incorporation of cations in the interlayer spacing of the silica sheets. Kimberlite exposed to cupric cations showed very strong weathering, indicating that this type of weathering may be considered a viable process option. Kimberlite fines generated after weathering with monovalent cations showed poor settling behaviour compared to kimberlite weathered with di-, and trivalent cations.

Jan 1, 2005