Search Documents

By P. Rice, A. Photolo, A. C. Barnard

Introduction -Sampling Tool Project (STP) -History -Results to date -Costs -Questions

Jan 1, 2005

By M. Somerville, S. Sun

The liquidus temperature and viscosity of a range of melter slags produced in South Africa were determined. Drop-quench experiments were carried out on the supplied plant samples to determine the liquidus temperature and phase relations at sub-liquidus temperatures. The temperature measurement range covered 1300°C to 1630°C. Results from these experiments show liquidus temperatures for the melter slags to be in excess of 1500ºC with the chromium containing spinel as the primary crystalline phase. At lower temperatures, an olivine or pyroxene phase co-existed with the spinel phase. The viscosity of the slags was determined over a temperature range of 1350 to 1550°C, under a controlled atmosphere. Results show two orders of magnitude variation in the viscosity (0.2 to 20Pa s) with strong effects of slag chemistry and temperature. Slags with lower SiO2and Cr2O3concentrations were more fluid. Slags with the lowest FeOx and highest SiO2concentrations were the most viscous. These observations are in accord with general behaviour of silicate slags. While the presence of a spinel phase may have an effect on the viscosity of the melter slags, results obtained to date indicate a much stronger effect due to the presence of an olivine or pyroxene phase at lower temperatures. Keywords: phase equilibria, liquidus, viscosity, slags, olivine, spinel, pyroxene

Jan 1, 2004

By M. Maleki

Variogram analysis and kriging lack robustness in the presence of outliers and data with long-tailed distributions, which often arises when estimating grades in precious metal deposits. The capping technique, consisting of truncating the data to some top-cut grade, is widely used in order to mitigate the influence of the values in the upper tail of the distribution. However, this procedure omits part of the grade variability and is likely to provoke a bias in the estimates. To avoid these issues, a recently proposed approach is to decompose the grade of interest into three components (the truncated grade, a weighted indicator above the top-cut grade, and a zero-mean residual) and jointly estimate the truncated grade and the indicator by cokriging. This approach is attractive as it provides unbiased grade estimates, allows choosing the ?optimal? top-cut value, and essentially works with truncated and indicator data, thus avoiding the use of outlying values for calculating sample variograms and performing spatial interpolation. This work presents an application of this approach to a disseminated gold deposit that has been identified through exploration drilling. The effect of using an indicator covariate is assessed through leave-one-out cross-validation, by comparing the grade estimates with the true grades and with the grade estimates obtained with the conventional capping approach, which considers only the truncated grade as the variable of interest. As a result, cokriging the truncated grade and the indicator above top-cut grade outperforms the conventional capping approach, yielding significantly more accurate estimates. A few complementary guidelines are provided for validating the model hypotheses and for the implementation of cokriging.

Jan 1, 2014

By M. Sanchez, C. Morales, J. Palacios

The slag produced in the Peirce Smith converters at the Ilo smelter of Southern Peru Copper Corporation has shown a wide range of magnetite content, which introduces an additional problem in the smelting units due to materials? recirculation. However, the operation data analysis and the application of thermodynamic concepts have made it possible to produce slag with magnetite content between 18 and 20%. The results have suggested that matte grade enhances magnetite formation while silica controls its precipitation, and they are also influenced by the increasing temperature of the slag. Thus, in order to obtain the required magnetite content in the slag, matte grade is gradually enriched in equilibrium with slag containing from 25 to 32% silica.

Jan 1, 2004

Publications on hard rock tunnel support design in the South African mining industry have originated primarily from the goldmines during the past 50 years. Little has been published to date on the platinum and chrome mines of the Bushveld Complex. This paper covers the search for a suitable design methodology for off-reef tunnels at Impala Platinum Mine, situated on the Western Lobe of the Bushveld Complex. The fall of ground accident statistics for off-reef excavations of the mine are presented and the available rock mass quality evaluation systems are reviewed. The Q-Tunnelling Quality Index (or Q-Index) is selected because it assesses the important driving factors behind falls of ground at Impala. Two off-reef excavations are evaluated using the Q-Index, and it is shown that minor modifications are required for implementation at Impala. It will take some time before support design throughout the mine is based on the outcome of proper geotechnical investigations based on the Q-Index. Widespread implementation of such support designs should help to solve the fall of ground problem in off-reef excavations while at the same time reducing support costs.

Jan 1, 2002

By K. Saito, Y. Miyauchi, T. Nishi, Y. Kizu

At Tokushima Plant of Nippon Denko Co., Ltd. high-carbon ferromanganese is produced by the electric furnace method using lump manganese ores and sintered manganese ores manufactured from fine manganese ores. However, the distribution of manganese ores is significantly uneven on earth, and their characteristics considerably vary by ore type. It is known from experience that the production of high-carbon ferromanganese by the electric furnace method depends greatly on material ores. Therefore, to maintain stable operation in the electric furnace-smelting field, it is important to identify the characteristics of each type of material ores in advance. Thus, we evaluated the high-temperature electric characteristics of manganese ores using the electrical conductivity measuring system developed by ourselves and provided the standards for determining ores and blending ratio necessary for stable operation of the electric furnace based on the evaluation results. This time we worked for optimisation of the high-temperature electric characteristics of sintered manganese ores through modification of the characteristics because the blending ratio of sintered manganese ores in the electric furnace is high. The electrical conductivity of sintered ores having various chemical components in a high-temperature region (up to 1 550°C) was measured using our electrical conductivity measuring system and high-temperature electric characteristics evaluating method reported at INFACON 9. As the result of the measurement, we revealed that the high-temperature electric characteristics of the sintered ores depend on their chemical contents and the sintered ores can be modified to those having excellent high-temperature electric characteristics by controlling their chemical contents, so that the resources can be effectively used.

Jan 1, 2004

By T. Markus, K. Hilpert

Discharge vessels of advanced light sources are made of translucent polycrystalline Al2O3(PCA).These tubes contain salt mixtures, which essentially consist of metal halides. The salt mixture is present as a melt at the coldest spot of the vessel under operating conditions and vaporizes partly. The temperatures of the coldest spot range between 1200 K and 1300 K, depending on the lamp performance. The maximum wall temperatures range up to 1500 K and for special purposes up to1700 K. Important constituents of the melt are alkali halides AX (A = Na, Cs, X= Br, I) and rare earth metal halides LnX3(Ln = Dy, Ho, Tm). Severe corrosion attack on the wall material is observed in the PCA discharge vessels. The aim of this work is to elucidate the corrosion mechanism. Annealing experiments under well defined temperatures were carried out in order to understand the complex chemical corrosion processes. Two different annealing vessels were used, one for experiments under isothermal conditions with a temperature of 1473 K and one for experiments with a linear temperature gradient from 1450 K to 1600 K. The vessels were filled with salt mixtures of different compositions and annealed for 1000 h. The corrosion attack was characterised by XRD, analytical electron microscopy, high temperature mass spectrometry, and chemical analysis of the salt melts. The results of our investigations show that the corrosion attack is caused by vapour species and by the salt melt. The most severe corrosion is observed in vessels filled with mixtures of alkali halides and rare earth metal halides. No corrosion of the alumina is practically observed if pure alkali halides or pure rare earth metal halides are present in the annealing vessel. Keywords: thermodynamic, corrosion, lamps, metal halide salt

Jan 1, 2004

By M. Magnelöv, Du Sichen, U. Sjöström

An experimental study has been performed to investigate the behaviour and separation of inclusions at the interface between steel and slag. The study has been limited to liquid inclusions because they can be a potential problem in transient situations such as ladle changes in continuous casting of steel. Model experiments with water and silicon oils have been carried out to study the kinetics of separation of simulated inclusions at an interface. The properties of the inclusions and the slags have been varied by using different oils with different viscosities, densities and surface tensions. The effect of temperature of the liquids has also been examined. Measurements of the terminal velocity, rest time and the behaviour of the liquid inclusions at the interface have been recorded using a video camera. It has been found that the inclusions reach their terminal velocity early in the vessel and the experimental velocities differ somewhat from the values evaluated using ?intermediate law?. The results from the experiments have shown that the size of the inclusions has no appreciable influence on the rest time. Droplets of AK50 oil have been found to have considerably long rest time. A water film surrounding the droplet has been expected to be the main reason for the long rest time. The present study has also shown that the viscosity of the oil has certain effect on the rest time, but only to some extent, since viscosity has double functions. A higher viscosity provides higher resistance to the droplet entering the oil phase leading to longer rest time and at the same time damps the lateral movement of the droplet along the interface, leading to easier stabilization and shorter rest time. On the other hand, a high viscosity of the oil phase results in slow dissolution process. It has been concluded that a meaningful model of inclusion separation at the metal-slag interface must take the interfacial phenomena into consideration. Keywords: Inclusions, terminal velocity, rest time, dissolution.

Jan 1, 2004

By V. Coetzee

In 1992, a paper was compiled highlighting a common-sense approach to electric smelting at Impala Platinum. Since then, the smelter complex has undergone considerable changes. Mineral economics, UG2 exploitation, and changing environmental legislation have enforced numerous process upgrades, yet a common-sense approach has always been adopted. This document details the major changes in the smelter complex at Mineral Processes (Minpro) over the past 15 years, and provides the rationale for the changes. Keywords: Pyrometallurgy, furnace, PGM, platinum, nickel, copper, electric smelting, six-in-line, Peirce-Smith, Impala Platinum.

Jan 1, 2006

By J. Eriksson

Slag from stainless steelmaking is known to disintegrate, which is an environmental problem and prevents the cooled slag from being utilized. This disintegration is due to the transformation from the ßto the ? polymorph of di-calcium silicate. The transformation is accompanied by an increase in volume of about 11% and a total disintegration of the slag. AOD slag from stainless steelmaking was re-melted in a laboratory induction furnace, together with olivine and calcinated dolomite, to investigate the prevention of disintegration by increased MgO content of the slag with small changes in CaO to SiO2ratio. The modified slag was examined with X-ray diffraction and scanning electron microscopy. The trials showed that an increased MgO content can change the mineral composition towards formation of more Merwinite and Bredigite, which prevents disintegration of the slag. Keywords: slag, disintegration, di-calcium silicate

Jan 1, 2004

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The stability of a ferrosilicon dense medium suspension is one of the most important parameters to keep under control since it determines the density gradient of the medium in the separation zone and thus directly influences separation sharpness. The stability of ferrosilicon suspensions were characterized using settling tests employing a differential pressure method. Particles smaller than 45 µm and especially the ore fines played an important role in the settling behaviour of the solids. High medium stability is favoured by ore fines, fine medium particles, and high medium densities. Keywords: dense media, ferrosilicon, dense medium stability, ore fines

Jan 1, 2002

By C. Righi, R. Carli

In modern steel continuous casting technologies mould fluxes are well-known to assure lubrication required by tribological system of mould-solidifying strand shell, and to provide crystalline phase solid film, contributing to control heat extraction between strand and mould wall. Actual cooling rates during normal continuous casting mould operations are far higher than critical cooling rate of the liquid slag. Indeed, DTA measurements point out that even relatively small cooling rates of 30?50 K/min are high enough to give exiguous formation of crystals. In this paper, contribution of devitrification in defining crystalline phase formation of industrial basic mould slag, used in continuous casting of crack-sensitive steel grades, has been investigated by means of non-isothermal experiments study. Devitrification has proved to play a major role in mould flux crystallization in a working environment explaining the higher amount of crystalline phase formed in plant sample in comparison with lab sample from DTA analysis with typical cooling rate of 5?20 K/min. The amount of crystalline phases formed ranks as follow: Cuspidine > Combeite > Gehlenite. Kinetic analysis of DTA non-isothermal experiments has provided kinetic parameters through Kissinger and Ozawa methods, as Avrami constant resulting to be n ?2 and activation energy of Cuspidine crystallization resulting to be EC= 315 kJ/mole. The effect of addition to the parent material of oxides as MnO, TiO2, ZrO2, Al2O3 and Fe2O3near to saturation point has proved to affect, in certain cases, crystallization behaviour of mold flux. In particular, MnO, TiO2, ZrO2oxides produce a relevant dump of crystallization of Combeite and Gehlenite phases, while Al2O3and Fe2O3do not appreciably affect crystallization. Key words: Mould flux, crystallization, devetrification, DTA non-isothermal analysis, Kissinger and Ozawa methods.

Jan 1, 2004

By M. Görnerup, M. Hayashi, S. Seetharaman, C. -Å Däcker

The mould flux plays a crucial role in the continuous casting operation of steel due to its multi-functional assignment as lubricator and heat flux controller. In reality, the commercial fluxes can fall short of the expectations of the operator. In such cases, the performance of the mould flux reduces production throughput in the casting machine. This paper presents the results of a study of two different commercial mould fluxes in continuous casting of steels. The results of online sampling during casting, as well as off-line measurements in the laboratory, are presented. Mould flux powder and slag samples from the caster have been characterized with respect to melting behaviour, interfacial tension and thermal diffusivity, using various measuring techniques. An experimental technique has been developed in order to simulate the melting behaviour of a flux in the mould, which has been found to be useful for qualitative studies. A cross-sectional view of different powders reveals that up to four different material layers may exist in the bed: a loosely packed powder layer, sintered layer, semi-solid layer and liquid slag layer. It is found that the melting rate of the mould flux is dependent on the liquid slag layer thickness. Thus, in a continuous casting operation the melting rate is likely to be non-uniform with position in mould due to the difference in liquid slag layer thickness. Mould slag composition is found to be influenced by the starting powder for as long as 30 min, representing a large part of the first heat casting time. Observations of gas formation indicate that interfacial reactions between the steel and slag take place. Keywords: continuous sacting, mould flux, mould slag, properties

Jan 1, 2004

By Valérie Léveillé

As new legislation drives to lower SO2 emissions from metallurgical plants, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an amine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 byproduct stream, which can then be directed to the front end of a sulfuric acid plant for conversion to sulfuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulfuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature SO2 emissions in the treated gas can be controlled to as low as 55 mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System and what as well as which features and cost advantages for the treatment of smelter gases were key to the technology choice.

Jan 1, 2009

By A. V. Pavlov, A. V. Dubachev, K. L. Kossyrev

The purpose of the given research was to investigate the possibility of high-carbon ferrochromium refining to remove harmful impurities as a result of metal treatment by slag mixtures on the basis of the CaO-MgO-SiO2system. The final conclusions were drawn from experimental results. It was shown that the treatment of high-carbon ferrochromium by SiO2-MgO-CaO slag mixtures with additions of chromium sinter or iron-ore concentrate removes carbon, sulphur and phosphorus from the metal. A mechanism of phosphorus removal from a melt to a gas phase is proposed.

Jan 1, 2004

Published experimental data on thermodynamic behaviour of cobalt-containing slags have been reviewed and used in validating a recently developed thermodynamic model. The results from the exercise show that the model provides a reasonably good description of behaviour of cobalt in multi-component slag systems. The models for cobalt containing slags, matte and oxide solid solution phases were incorporated into CSIRO?s multi-phase equilibrium (MPE) package, which was used to calculate the equilibrium distribution of cobalt between matte and slag phases under various conditions. The results agreed well with the experimental data. Furthermore, the good agreement between the calculation and the plant data indicates that the operating conditions of industrial smelting and converting processes are close to equilibrium. Two diagrams showing the effects of slag chemistry and SO2and O2partial pressures on the distribution of cobalt between phases were generated for conditions similar to smelting and converting processes. These diagrams provide some useful guidelines for developing new strategies to improve cobalt recovery.

Jan 1, 2004

A comprehensive review of ore pass records, from ten Quebec underground mines, indicated some of the limitations of available design tools to predict the occurrence of ore pass interlocking hang-ups in metal mines. The Distinct Element Method was used to perform a series of numerical experiments in order to investigate the influence of ore pass geometry, rock fragments shape and size distribution on material flow in an ore pass. Guidelines have been developed to help limit the occurrence of interlocking hang-ups in an ore pass. The proposed guidelines were evaluated with respect to field observations. Ein kompletter Bericht der Erzrollezeichnungen, von 10 Quebec unterirdischen Gruben, hat einige der Beschränkungen der vorhandenen Designwerkzeuge angezeigt, um das Auftreten Erzrolle der blockierenhang-ups in den Metallgruben genau vorauszusagen. Eine Reihe numerische Experimente mit der eindeutigen Element-Methode, wurden aufgenommen, um den Einfluss von Erzrollegeometrie, Partikelform nachzuforschen und Felsenkorngrößenverteilungen auf Materialfluss in ein Erz überschreiten. Dieses hat zu die Entwicklung der Richtlinien geführt deren Implementierung das Auftreten der blockierenhang-ups in eine Erzrolle begrenzen sollte. Die vorgeschlagenen Richtlinien wurden in Bezug auf Labor- und Feldbeobachtungen ausgewertet. Une revue de la performance actuelle des cheminées à minerai dans 10 mines souterraines du Québec a indiqué les limites des outils de conception servant à dimensionner les cheminées pour minimiser le nombre d’accrochages par enchevêtrement rocheux. Des séries de modélisations numériques, utilisant la méthode des éléments distincts, ont été réalisées afin d’évaluer l’influence de la géométrie des cheminées, de la forme des fragments rocheux et de la distribution granulométrique sur l’écoulement du matériel dans les cheminées. Cet exercice a permis de développer des lignes directrices pour le dimensionnement des cheminées afin de limiter l’occurrence d’accrochage par enchevêtrement rocheux. Les lignes directrices proposées ont été évaluées en fonction des observations effectuées sur le terrain.

Jan 1, 2003

By M. L. Smith, G. Karunatillake

Lead-zinc production at MIM, Mount Isa includes three mines, a lead concentrator, zinc filter plant and lead refinery. Lead production is vertically integrated with lead-silver bullion shipped from Australia to London for refining. Zinc is sold as a concentrate. All three mines have reached varying states of maturity mining a multitude of orebodies having significant variation in grades and metallurgical recovery for three metals. Based on current levels of measured resources, the remaining project life is at least ten years. The objective is to schedule production over the life of all three mines so as to maximize the present value of the complex. Additional scheduling complexity arises out of the implementation of long-term schedules, capital expansion projects for both mining and processing, the presence of substantial inferred reserves and interactions with MIM copper production. A large-scale, time-dynamic, life-of-complex Mixed Integer Program (MIP) production schedule was formulated to optimize lead/zinc cash flow based on a detailed life of project production scheduling study. The requirements for such a study are detailed herein. The operational feasibility of the MIP solution is compared against a non-optimal approach to strategic life-of-mine scheduling. The strategic planning emphasis placed on the MIP is compared to the implementation of a life-of-mine schedules at Mount Isa using spreadsheets and other popular commercial mine schedulers.

Jan 1, 2003

By J. Björkvall, S. Ångström, L. Kallin

In this paper results from industrial trials of CaC2 injection during stainless steel production in an electric arc furnace at Sandvik Steel is presented. The main purpose of the investigation was to analyse the effect of the injection on slag foaming and final chromium oxide concentration in slag. The results show that both an increase in slag foaming and a decrease of the final chromium oxide could be obtained during the charges with CaC2injection. On the basis of the results, the economical requirements are also discussed. Both the technical and economical requirements could be achieved for steels alloyed with Mo. In order to secure the economical requirements for all steel grades of interest, the injection technology must be further developed. It would also be important to utilize the positive effect of the slag foaming on the electric energy consumption. The work has been performed as a part of MEFOS frame research programme with participants from Sandvik Steel, AKZO Nobel and Avesta Polarit. Keywords: stainless steel, EAF, slag foaming, injection, CaC2

Jan 1, 2004

By J. Böhlke, B. Friedrich, E. Hecker

The legislation for the disposal of heavy metals contaminated substances is still going to be tightened up in the future. The main criteria for the utilization or deposition of these residues are the content and the water solubility of these metals. Through this, the use of slags from the lead-and zinc-industry in road building may become limited or even not possible at all. From an economic point of view this would lead to Pb/Zn losses and costs for safe dumping. This paper investigates the feeding of the reducing agent via hollow electrode DC smelting and the yield of metal reduction. After carrying out thermodynamic calculations, the process window conditions for electric-arc furnace tests were determined. Doing this, the zinc could be reduced, evaporated and recovered as an oxidic intermediate product flue dust, while the lead was present either in flue dust or in metallic form. The zinc content in the final slag could be reduced by up to 90%. The slag product has undergone an eluation test which allows it to be used as building materials. Keywords: zinc reduction, lead reduction, hollow electrode, slag treatment, electric arc furnace