Search Documents

During the summer of 1973 we were asked to perform a theoretical investigation of the propagation of low frequency (LF) radio waves down deep (10,000 feet) hoistshafts* for the case where the hoist cable ("rope") is the only metal conductor present. Propagation is by means of the TEM coaxial mode of transmission in which the hoist cable serves as the inner conductor and the surrounding rock acts as the outer conductor. Since the rock is a relatively poor electrical conductor the current in the outer conductor of the coaxial line is not confined to a very thin surface layer as in a metal coaxial cable, but spreads radially to a distance that is generally many times the shaft diameter. This feature of the wave propagation requires a more sophisticated theoretical treatment than the approximate skin-depth theory that is adequate for metal coaxial lines. In this Part we treat the hoist shaft wave propagation loss, characteristic impedance, and the field current distributions in the surrounding rock medium. We also show that the large penetration of the wave into the rock outer conductor does not present a difficult problem with regard to coupling the transmitter or receiver to the transmission line with a minimum of insertion loss, but that the large impedance mismatch caused by the capacitance termination between the cage and shaft wall may well be the most significant contribution to overall system loss. Inductive coupling and impedance matching to the hoist rope/shaft transmission line are also treated briefly. Preliminary results indicate that a broad minimum in overall system loss should occur between 100 kHz and 1 MHz, possibly centered around 300 kHz. Further work is needed to better quantify this signal loss behavior, compare it with hoist shaft electromagnetic noise spectral data recently acquired by NBS, and identify the most favorable operating frequencies.

Jan 1, 1974

By George A. Morgan

Mineral production was confined to out-put of cement and gravel. However, exploration was being conducted by the U.S.S.R. and the United Nations Development Program. Development of a domestic limestone deposit and crude oil from an offshore oilfield was underway. Benin's currency remained fixed to the French franc. The gross domestic product (GDP) was $977 million in 1981, the latest year for which information was available. 2 COMMODITY REVIEW Cement.-Construction of a cement plant with 500,000 tons per year capacity neared completion at Pobé. The operator of the plant, using locally produced limestone, was the Societe des Ciments d'Onigbolo, a joint venture between Benin and Nigeria. Nigeria was expected to utilize most of the cement produced. Equipment for the plant included a 1,600-ton-per-day, oil-fired pre-heater.

Jan 1, 1984

By C. D. Litton

The results of full-scale fire tests are used to determine optimum distributions of fire sensors for the protection of conveyor belt haulageways in underground coal mines. Empirical relationships are derived that relate the spacing of fire sensors to the rate of development of the fire hazard. For this application, a critical fire size is defined as that size of fire for which belt ignition and subsequent flame spread down the belt is assured. Detection and alarm, regardless of sensor type or sensing methodology, must be achieved at some point in time before the critical fire size is reached. Based upon this approach, it is found that the horizontal spacing for products-of-combustion sensors is in the range of 300 to 600 meters, while the required thermal sensor spacing is found to be ~4 meters or less. Additional design criteria are discussed for product-of-combustion fire sensing systems.

Jan 1, 1982

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1985

By Kenneth L. Cashddollar, Terry G. Montgomery, Eric S. Weiss, John E. Going

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRI, Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test -was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere.

By David W. Houseknecht

Probabilities of encountering coalbed discontinuities during vertical or horizontal drilling in a specific coalbed can be estimated based on analysis of mined-out areas of the coalbed where the size, shape, orientation, and distribution of discontinuities are known. The result-ant probability estimates can be applied to cost-risk evaluations of drilling programs proposed for exploratory, developmental, or methane drainage purposes in undeveloped areas of that coalbed. Data compiled from mine maps of the Beckley Coalbed in southern West Virginia were used to estimate the probabilities that discontinuities would be encountered in two illustrative hypothetical drilling programs--one for drilling vertical boreholes and the other for drilling horizontal boreholes. Analysis based on a mined-out area of the Beckley Coal bed indicated that vertical methane drainage boreholes spaced 1,000 feet apart in a square grid pattern would each have a 29 percent probability of encountering a discontinuity in a geologically unexplored area of the coalbed. It was also determined that exploratory vertical drilling could locate most of the discontinuities if a borehole spacing of 2,500 feet were used. For horizontal drainage boreholes in the Beckley Coalbed, the analysis indicated a linear relationship between hole length and the probability of encountering a discontinuity.

Jan 1, 1982

By Ralph L. Brown

"IntroductionThe accumulation of gummy and resinous deposits in consumers' gas meters began to assume serious proportions about 1917. As the trouble developed and spread in the years following, it manifested itself in several ways, which ultimately began to the expressible in distinctly economic terms, more specifically in terms of costs; in 1922 an organized and fundamentally based investigation of this trouble was begun. In an earlier paper*** a short statement of the occurrence and costs of the deposition was given and at the same time an analysis of the problem, as well as well as a general plan of attack, was presented. That plan included two general phases, first, a chemical study of typical was 1 quarry or 2 cosinous content , mauformly consituents, rmln and selected subjects; and secondly, a comparative survey of plants affected and sufficient therewith, attention being paid to construction, operation, meter conditions and related data. In reporting progress in the axtual investigation, it was definitely set down that the basis of the gummy deposits was the unsaturated hydro consulting from the carburxtion of the water-gas with oil. That the presence of oily-gas condensate was closely associated with and largely"

Jul 1, 1923

By A. W. Henderson

The growing importance of halide metallurgy for preparing high-purity metals has stimulated research to extend halogenation reactions to the direct extraction of metals from low-grade sources. This Bureau of Mines investigation involves a pioneering study of chlorination reactions in the presence of a fluorine donor. Tin slags containing tantalum and columbium and a zircon concentrate containing a relatively high ratio of hafnium to zirconium were studied. Direct chlorination of these materials at 500° C. yields only a 5-percent conversion of tantalum and columbium or zirconium and hafnium to anhydrous chlorides. This investigation showed that small additions of calcium fluoride to the reaction increased the recovery of tantalum and columbium to 95 percent and the recovery of zirconium and hafnium to 27 percent. These results were achieved with ratios of calcium fluoride to mineral or slag of only 0.2. Silica, the major impurity in the materials studied, was found to be converted to silicon tetrafluoride during chlorination in direct proportion to the quantity calcium fluoride added to the charge. However, large additions of calcium fluoride decreased the volatility of the resulting halides of tantalum, zirconium, and hafnium. Smaller amounts of calcium fluoride also favored recovering minor metal constituents in the zircon concentrate (uranium, thorium, and rare earths).

Jan 1, 1962

By Jack C. White

As part of an investigation of the production of alumina by the nitric acid leaching of kaolinitic clay, the Bureau of Mines designed, built, and tested a fluidized-bed system for the calcination of aluminum nitrate nonahydrate to alumina, while recovering nitric acid. The calciner consisted of an 8-in-square by 36-in-tall vessel containing 18 in of fluidized solids. Molten aluminum nitrate, sprayed directly into the fluidized solids, formed sandy, granular alumina by growth of successive layers on fluidized particles. Solids were fluidized in a dense bed at temperatures of 250° to 500° C with steam, air, or mixtures thereof. Decomposition of nitrate ranged from 4 to 10 pet during single-pass steam or air fluidization, respectively. Alumina dust losses and low throughput are significant unsolved problem areas.

Jan 1, 1982

By N. N. Moebs

The Bureau of Mines air-sealed a 77-acre) above-drainage coal mine to evaluate sealing as a means of reducing the acid and metallic salt contents in drainage from abandoned mines. An approximate reduction in acidity of 150 ppm (equivalent to 193 pounds per day) and in iron of 98 ppm were directly attributed to sealing. The topographical, hydrological, and other factors involved in air-sealing are discussed, and the construction used to seal the mine is described.

Jan 1, 1970

By R. E. Head, Virgil Miller

"INTRODUCTIONRecent investigations at the Intermountain Experiment Station of the Bureau of Mines at Salt Lake City indicate that metallurgists have given little attention to the occurrence of jarosite minerals in the oxidized ores of lead and silver. These investigations have also emphasized the importance of knowing when these minerals occur in the oxidized ores, especially those containing lead, silver, and gold, as their presence is a material factor in selecting a suitable kind of treatment. Since the question of the occurrence of jarosites in oxidized ores has come to the attention of the Bureau of Mines, investigation has indicated that plumbojarosite and argentojarosite are quite common. These two minerals appear to be widely distributed and probably escaped recognition by persons who had attempted to treat certain oxidized lead ores in which the jarosite minerals represented a material portion of the metal content.Consideration of the physical characteristics of the jarosites also indicates that in many cases failure to treat some of the oxidized lead ores with success has been directly due to the fact that the greater portion of their lead and silver content was present as plumbojarosite and argentojarosite. The data and the description of these minerals given in the body of this paper indi¬cate that attempts to recover lead and silver from ores in which appreciable amounts of the metals occur as plumbojarosite and argentojaeosite would be unsuccessful if confined to gravity methods of concentration. There are un-doubtedly considerable tonnages of oxidized lead ores in the various mining regions of this and other countries, and it is quite probable that in some of these ores the metal content of lead and silver may be largely anglesite (lead sulphate) and cerussite (lead carbonate) but that they will also contain cerargyrite (silver chloride), argentojarosite, and plumbojarosite. The treatment of such ores therefore presents an important problem, since a product is discarded from ores from which the recoveries of lead and silver have been below 70 per cent which is probably too low-grade to warrant aftertreatment by any process now in use."

Apr 1, 1928

By H. D. Jacobs

The Bureau of Mines developed a concentration method to upgrade and utilize marginal natural or direct-shipping iron ores and fine-grained lean iron ores. Presently these ores receive little beneficiation and accordingly have low iron-silica (Fe-Si02) ratios. Ore samples were roasted with equal weights of solid reductant at 1,100° C for 1 hour to metallize the iron and for an additional hour at 1,200° C to promote grain growth. Concentration was effected by crushing and screening techniques and/or wet magnetic separation. Sized concentrates (minus 4 plus 35 mesh) derived from crushing-screening processes contained from 80 to 85 percent iron that was 90 percent metallized. Iron-silica ratios as high as 12:1 and iron recoveries from 75 to 94 percent were obtained. The sized concentrates were judged suitable for use as blast furnace feed. Minus 200-mesh metallized concentrates derived from roasted minus I-inch plus 8-mesh ore fractions and magnetically concentrated contained 90 percent Fe and 4 percent or less Si02, chemically qualifying them as feed for electric furnaces. Roasting minus 8-mesh ore with hydrogen, then magnetically concentrating it, produced iron concentrates containing 57 percent to 67 percent Fe and 3.6 percent to 8.4 percent Si02. The concentrates having Fe-Si02 ratios ranging from 8:1 to 12:1 were considered adequate for use as blast furnace feed. Overall iron recoveries for the 12 ores tested ranged from 56 percent to 94 percent with an average iron recovery of 86 percent.

Jan 1, 1969

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Boone County, W. Va., as determined by the Bureau of Mines. It is one of a series describing the coals suitable for producing metallurgical coke, either as mined or after beneficiation. Over 6.3 million tons of coal was produced in Boone County, W. Va., in 1959, of which almost 5.5 million tons was mechanically cleaned in eight preparation plants. On December 31, 1959, it was estimated that almost 8 billion tons of coal remained in the county in beds 24 inches or more in thickness. Thirteen samples were collected from nine coalbeds and washability tests were made on these samples.

Jan 1, 1961

By George S. Koch

Several methods of calculating ore grades by diamond-drill sampling in the Homestake mine, Lead, S. Dak., have been evaluated by statistical analyses of assay data. The natural distribution of gold particles, partly masked through sampling and assaying procedures, is probably lognormal. As a consequence of the gold particles being clustered rather than randomly distributed within the ore bodies, (1) more mine samples are needed to obtain a specified precision of mean grade than the number predicted by the standard-error-of-the-mean law; (2) the variance of gold values is not inversely proportional to sample volume, and, therefore, small-diameter drill core yields samples nearly as good as larger diameter core; and (3) sampling at 5-foot intervals provides nearly as good results as sampling at shorter intervals.

Jan 1, 1971

Objective As mines become safer and disasters fewer, a time may come when no employees in the mining industry have any practical experience in managing a mine emergency. To fill an emerging gap in mine emergency response training, a multidisciplinary team of researchers and computer programmers from the NIOSH Pittsburgh Research Laboratory has developed an intervention for mining personnel who would be in leadership positions in the command center during emergencies. It is called MERITS, a computer-based emergency simulation exercise. MERITS is short for "Mine Emergency Response Interactive Training Simulation." It provides trainees an opportunity to gain command center experience during a simulated underground coal mine emergency. MERITS allows trainees to practice information gathering, situation assessment, decision-making, and coordination skills without risk to personnel or property. Individuals representing mine emergency response personnel, various State safety officials, and private mine management from three States have participated in MERITS training. What Is MERITS? MERITS is an extension of previous work that compiled a knowledge base relevant to mine disaster management via interviews, analysis of literature, reviews of past events, and observations of mock mine disasters. Findings from prior research found a need for an alternative method of command center training. This new computer simulation is being used to train emergency command center personnel to effectively manage an underground mine fire. Modeled after training simulations developed for other industries (e.g., to address nuclear accidents, chemical spills, evacuations, etc.), MERITS simulates underground and surface events related to the disaster. It exposes the user to events that typically occur during a mine emergency, such as lack of information and miscommunication. It also presents trainees with issues that must be addressed, such as making provisions for briefing news media and victims' families, ordering needed supplies, interfacing with Government enforcement agencies, and housing mine rescue teams. The outcome of the scenario is determined by the users' decisions and their emergency response plans. Field Results Field testing of MERITS was conducted with eight full-day training sessions at four different locations in Colorado, Pennsylvania, and West Virginia. These field tests benefited from the knowledge and experience of State of Pennsylvania inspection officials, representatives of the United Mine Workers of America(UMWA), and private mine management who served as trainees for the MERITS training sessions. Trainees self-reported an average of20 years of work experience in the mining industry. All trainees had participated in Mine Emergency Response Development (MERD) training exercises, and many had been involved in real mine emergencies. Trainee evaluation of the MERITS program is summarized below: •Twenty-six of the 27 trainees believed that the MERITS simulation helped them know how to prepare for a real emergency. •Twenty-five of the 27 trainees believed that the storyline for the MERITS simulation was either "very realistic" or "realistic." •All 27 trainees believed that the MERITS simulation helped them learn how to better handle a real emergency. •None of the 27 trainees stated that they were bored during the simulation. After the initial field tests, MERITS was refined and retested during training sessions for individuals from State agencies, the UMWA, and private industry. Mining personnel from underground coal and underground stone mines participated and responded positively to the learning experience. Technology Transfer Industry introduction to the MERITS program will occur throughout 2002. MERITS presentations at the Joseph A. Holmes Safety Association National Meeting in Virginia Beach, VA, in June.

Jun 1, 2002

By Ronald D. Hill, Elmore C. Grim

Sediment is one of America's greatest pollutants. More than a billion tons of sediment reach the major streams of the United States annually(l). Damages are reflected in the reduced carrying capacity of streams, clogged reservoirs, destroyed habitat for fish and other aquatic life, filled navigation channels, increased flood crests, degraded facilities for water-based recreation, increased industrial and domestic water treatment costs, premature aging of lakes by enrichment of the water with silt-carried fertilizer that promotes algae growth, destroy crops, and reduce productivity of flood plain soils. Erosion and sedimentation are natural processes that are usually gentle actions releasing controlled amounts of silt from watersheds to receiving streams. Surface mining activities accelerate these natural processes and short duration, high intensity storms can become a violent force moving thousands of tons of soil in a brief period of time. Cover is a very important factor. With the removal of ground cover, water moves across the denuded area on its own terms picking up soil particles as it flows and leaving gullies behind. The susceptibility of strip-mined land to erosion depends on: 1.Physical characteristics of the overburden 2. Degree of slope 3. Length of slope 4. Climate 5. Amount and rate of rainfall 6. Type and percent of vegetative ground cover. By development of erosion and sedimentation control plans before disturbance of the area, many of the detrimental effects of strip mining can be prevented.

Jan 1, 1974

By Mark R. Pettitt

After a long series of laboratory and in-mine tests, a cost- effective, mineworthy, reduced-noise auger miner cutting head was de signed, fabricated, and field-tested by Wyle Laboratories under contract to the Bureau of Mines. Compared with standard auger cutting heads, the new heads reduced noise by 10 dBA at the jacksetter's position and by 6 dBA at the operator's position. This report contains detailed fabrication instructions, including engineering drawings, that show how a standard auger cutting head can be modified to produce a reduced-noise auger.

Jan 1, 1984

By Neil B. Young

Carbonate minerals constitute a major fraction of the oil shale in Colorado's Green River Formation. Quantification of carbonate minerals is important for the characterization of oil shale, particularly because of their thermal activity in production of oil from shale. The carbonate minerals found in this oil shale are nahcolite (NaHCO3), dawsonite [NaA1(OH)2CO3], dolomite [(Mg1-xFx)Ca(CO3)2], calcite (CaCO3), and ferroan [(Mg1-xFex)CO3]. Although carbonate minerals can be removed by acid extraction from the balance of the oil shale, direct determination of carbonate minerals is complicated by the occurrence of the same cations in more than one mineral. A method for assigning the acid-soluble cations to the individual carbonate minerals was developed from two assumptions based on oil shale geochemistry: (1) Calcite and ferroan do not occur together, and (2) the ratio of iron and magnesium is the same in dolomite and ferroan. These assumptions were tested by the Bureau of Mines by applying the technique for assigning cations to 219 samples from the saline section of the formation. The reported carbonate mineral amounts were compared statistically with X-ray diffraction peak heights, verifying the cation assignment method.

Jan 1, 1975

By N. C. Tomoeda, W. D. Bensema, J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 350 meters (1150 ft .) and 488 meters (1600 ft .) . The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broad- band, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or E layers of ionosphere as an upper plane and the earth as a lower plane. The measurement systems used are similar to those used earlier. The technique is to record broadband, analog signals, digitize the data, and use a fast- Fourier transform to obtain spectral plots. This tech- nique is novel in that it can measure simultaneously all magnetic field energy within a limited portion of the spectrum for a limited time, and, after processing, reproduce the events occurring in that time interval in great detail .

Jan 6, 1974

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operatons at or near mines.

Jan 1, 1963