Search Documents

By Terry J. Close

The Gates of the Mountains Wilderness study area is underlain by intrusive and sedimentary rocks, mainly limestone. No limestone has been produced from the study area; suitable material is more readily available elsewhere. Small amounts of gold, sapphires, and corundum were produced from a placer deposit along the banks of the Missouri River. The remaining gravel contains low mineral values. Other alluvial deposits along the Missouri River and Beaver Creek contain no identified economic resources other than sand and gravel. Some deposits could provide suitable construction material for local use.

Jan 1, 1984

Reduce longwall shearer operators' dust exposures by more effectively suppressing the dust generated by the upwind cutting drum. Approach Direct more of the shearer water supply to the upwind drum, thus reducing the shearer operator's exposure to respirable dust while making more efficient use of water. How Proportioning Permits More Efficient Use of Water On most longwall mining operations, the cutting action of the shearer drums is the primary source of dust. Al-though the amount of dust generated is directly related to the amount of coal and rock cut by the drum, the exposure or the shearer operators to dust depends more on their work position relative to the upwind drum. When cutting with the airflow, the upwind drum, cutting bottom coal and floor rock, is the primary generator of dust reaching the operators. The lead drum is downwind of both shearer operators and is thus of less concern. (See diagram). When cutting against the airflow, the lead drum is upwind-taking a full cut, including roof rock-and both shearer operators may be exposed to very high levels of respirable dust. Currently, water sprays mounted on the cutting drum provide the most effective method of controlling dust from longwall shearer drums, and all longwall mining operations use some type of bit flushing or cavity filling water spray system on the cutting drums. Bureau surveys of longwall operations, conducted as part of its research program to reduce respirable dust, have indicated that six longwalls with better than average compliance records use higher than normal water flowrates to the cutting drums. The average water flow to the shearers at these six operations was approximately 60 gpm-about 50 percent more water than is normally supplied to double-drum longwall shearers.

Jan 1, 1982

By George H. Johnson

An evaluation of the diamond-bit-performance data accumulated from core-drilling cherty limestone and cherty dolomite reveals that the percentage of core recovered and the physical characteristics of the bits and diamonds used are economically significant. One of the established trends, of particular interest to those engaged in diamond drilling, is that bits set with small, low-quality, West African drill bort are the most economical. Detailed analysis of the factors that affect diamond-bit performances, such as diamond size and quality, bit size and type, percentage of core recovered, and the physical characteristics of the bit matrices are assessed in the tables, charts, and discussion.

Jan 1, 1958

By R. H. Nafziger

As part of its program to help decrease the dependency of the United States on foreign imports of nonfuel minerals and to devise technology for the efficient and economic use of domestic resources, the Bureau of Mines smelted and sulfation-leached an ilmenite from northern Minnesota. The objective was to assess the feasibility of preparing chlorination-grade titanium feedstock. The concentrate was smelted with woodchips, coke, and soda ash in 91-kg-and 1-metric ton (mt)-capacity electric arc furnaces to form Ti-rich slag and commercial-grade pig iron. The slag contained from 67 to 77 wt pct titanium oxides and from 1.8 to 7.2 wt pct iron. Sulfation occurred in a 4.5-kg/h moving-bed reactor using S02-air mixtures at temperatures of 8000 to 8500 C to form soluble salts of the Ca, Mg, Mn,and Na impurities, which cause plugging of fluidized-bed chlorinators. Subsequently, the sulfated slag was leached in acid to remove the soluble sulfates. The final product from small-scale testing contained up to 95.5 wt pct Ti02, a minimum of 0.6 wt pct Fe, and a minimum total of 0.3 wt pct of the four impurities of interest. The final product meets charge specifications for chlorination. However, more large-scale testing is necessary.

Jan 1, 1987

To evaluate the potential for dust reduction, during blasthole drilling, of water or foam applied directly into the drill hole. Approach The Bureau of Mines tested a through-the-drill-steel water and foam injection technique in two noncoal mines to evaluate the method's potential for greater dust reduction. The tests were performed by drilling a series of blastholes for an entire face (a 90 minute time-period). For the first 45 minutes of drilling, foam or water was applied through the drill steel. Blowing ventilation was supplied to the entry about 50 feet from the face. The dust concentration measurements were made by a Real-Time Aerosol Monitor (RAM-I), and the data were read out on a strip chart recorder. The evaluation test results showed that the water or foam injection technique, when used on localized dust sources, can be an extremely effective dust control method. Small amounts of water used in this method have also allowed it flexibility to be used in water-soluble ores such as salt, gypsum, anhydrite, and trona. How The System Works Water or foam is mixed with compressed air (approximately 100-120 psi) with suitable metering systems and forced through the drill steel into the blast hole at the point of dust generation. Because the water or foam is applied at the source, minimal quantities of liquid are needed (0.2 to 0.6 gpm). These low flowrates are sufficient to just moisten the dust emerging from the blast hole, thus eliminating a major source of airborne dust. The wet drilling procedure also eliminates a second source of dust. With dry drilling, the dust from the blast hole falls to the floor. Since this can be a 15-ft drop or more, the impact can send the dust billowing up from the floor, adding to the airborne dust. With wet drilling, the moistened dust merely dribbles down the face.

Jan 1, 1982

By Daniel Edelstein

In 1985, ASARCO Incorporated terminated copper smelting operations and associated byproduct arsenic trioxide recovery at Tacoma, WA, although shipments of arsenic trioxide from stocks and limited production from cleanup operations continued. Imports of arsenic trioxide increased markedly as a result of increased demand for arsenical wood preservatives and the decline in domestic shipments of trioxide. Expanded world capacity more than met the increased demand for arsenic and its compounds, and prices remained unchanged throughout the year. Domestic Data Coverage.-Arsenic trioxide was produced by one U.S. company, which voluntarily reported its production to the Bureau of Mines.

Jan 1, 1987

By P. W. Jeran, S. J. Pepperney, M. C. Irani, F. F. Kopsch

The Bureau of Mines has designed and put into operation a fail-safe control system for use in underground coal mines equipped with methane drainage pipelines. This control system can detect certain unsafe conditions and respond by automatically shutting off the flow of methane from the degasification borehole to the drainage pipeline. Methane flow is shut off when the methane content in the return airways reaches a predetermined level (typically 1.5 pct), when the methane drainage pipeline is ruptured by roof fall, or when there is an electric power failure. The fail-safe control system was designed using commercially available components and a methane analyzer system previously developed by the Bureau. The fail-safe system consists of a unit that combines a shutoff valve and pneumatic valve actuator, and electronic and mechanical equipment designed to detect hazards and effect shutdown. The fail-safe control system was designed to meet regulatory requirements issued by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and State regulatory bodies for the safe operation of underground methane pipelines used for mine degasification. MSHA has inspected and tested this system and permitted its use in two mines. The Bureau installed the fail-safe system in two working coal mines, where successful performance has been demonstrated.

Jan 1, 1980

By D. Z. Hobbs

Because an economic method for preparing pure boron has not been developed, a program was started by the Bureau of Mines to evaluate existing techniques or to develop new methods for preparing the pure element. This report describes investigations directed toward the development of techniques for the preparation of pure boron by fused-salt electrolysis. Only two of the several fused-salt baths tested were satisfactory for the preparation of boron. These baths contained (1) potassium fluoride, lithium fluoride, potassium fluoborate and boron trioxide; and (2) potassium fluoride, potassium chloride, and boron trioxide. Of these two mixtures, the latter was more satisfactory. Elemental boron of from 90- to 95-percent purity and, in isolated cases, as high as 98-percent purity, was prepared from these two types of fused-salt baths. There appeared to be no distinct differences either in the yields or the purity of boron prepared at current densities ranging from 795 to 1,000 amperes per square foot. Current efficiencies were as high as 85 percent.

Jan 1, 1961

Many different types of structures and materials have been used to build mineral processing facilities throughout the years. Although structure type and building material were not viewed as significant factors affecting the health of employees in these facilities when they were built, the National Institute for Occupational Safety and Health (NIOSH) has found that building type can impact respirable dust and noise levels. NIOSH performed a study in which it evaluated three building types: masonry, an open-structure design, and a steel-sided design. This study indicated that an open-structure design (no walls) was superior from both a dust and noise (health) standpoint when compared to the other two structure types. Therefore, companies may want to consider this design when building new structures.

By Francis Crowley

Elementary concepts of seismic wave properties are reviewed to establish a framework for discussing seismic noise and its suppression. A liberal number of references is included for those who wish to pursue the topic in detail. A base motion noise level is established for a single surface seismometer. It is argued that simple array processing and seismometer burial should regularly permit us to approach this base noise level which is found in areas free of conspicuous man-made seismic noise sources. The sensitivity of the base seismic level to a number of common disturbances is presented. Solutions that promise to hold the "effective" seismic noise at a site near the base level are given for acoustic, meteorological and fixed local surface sources. Guidelines are suggested for controlling other local man-made sources, e.g. vehicular traffic, by keeping them at sufficiently large distances away from the seismometers to keep noise at permissible levels. These guidelines are speculative and conservative. They should be the subject of future study. The ability to process against general local activity, drilling, and intra- mine sources is limited. Certainly no dramatic gain is to be expected. When strong man-made and/or intramine noise sources are not controllable, detection may well be impossible to achieve, unless the seismometer can be moved close enough to the suspected miner position, i.e. via very deep holes, to compensate for the likely vast differences in strength of the miner signal and the uncontrollable man-made noise sources. However, many intramine sources, e.g., falling water, rock bursts, explosions, etc., may well preclude the existence of a hale miner in their vicinity, and therefore any need to attempt detection of a miner at such locations. The following recommendations are made to enhance the detection and location of a miner signaling seismically. They are: 1. Seismometer burial in slim holes. 2. Narrow band detection, using multiple narrow band filters to cover the likely signal band. 3. Broadband recording and analysis for time-of-arrival estimation.

Jan 1, 1974

By Andrew J. Fergus

A study of the flotation characteristics of columbium-tantalum minerals was made by contact-angle and microflotation methods, and the findings were confirmed by flotation of two natural ores. In the contact-angle study conditions for collection of columbite, pyrochlore, and tantalite were determined for (1) sodium oleate with a sulfonate; (2) sodium isooctyl phosphate; (3) a short-chain primary amine; (4) a long-chain primary amine; and (5) a quaternary amine. These conditions were confirmed in microflotation tests. Information about collector action on common gangue minerals was also obtained by these two methods. In batch flotation tests on a pyrochlore ore and a columbite ore, it was demonstrated that collectors selected on the basis of contact-angle and micro-flotation studies would float columbium minerals from a complex natural ore. However, multiple cleaner and scavenger flotation steps will be necessary to produce commercial concentrates. From a pyrochlore ore containing 0.54 percent Cb2O5, a 44.4 percent Cb2O5 concentrate was made containing 36.4 percent of the total Cb2O5. For a columbite are the corresponding values were: 4.35, 54.6, and 67.1 percent. During the batch flotation study, wetting agents were found to aid in the gangue-ore mineral separations.

Jan 1, 1968

By F. Chase, D. Pappas

Pillar recovery has been associated with nearly one third of roof fall fatalities in underground coal mines during the past decade. Safe pillar recovery requires global stability and local stability. Global stability is addressed primarily through pillar design. The local stability risk factors include cut sequence, the final pillar stump, supplemental supports (timbers vs. Mobile Roof Supports (MRS)), roof bolting, and many others. The National Institute for Occupational Safety and Health (NIOSH) has evaluated each of these factors through field research and analysis of accident statistics. The paper discusses design methods and technologies that have been transferred to the mining community and implemented.

Roof bolting is a slow, expensive, and absolutely necessary mining activity. Roof-bolting activities also account for the largest percentage of lost-time injuries in underground coal mines. Dull bits result in the application of excessive force, which bends drill steel; and changing starter and finisher steel was the most significant source of injuries associated with roof bolting. The tungsten carbide (WC) roof-bolt drill bits currently used in American, Canadian, and Australian coal mines are capable of drilling only one or two 4-ft holes and then they are resharpened once or twice to drill another one or two holes. Often, in medium-hard rock formations (sandstone), as many as 20 to 30 bits may be required to drill a single 4-ft hole. Objective To compare the performance, longevity, and cost of newly developed polycrystalline diamond compact (PDC) roof-bolt drill bits against WC bits. Research and Background Diamonds for industrial use have been scarce throughout history and continuous attempts have been made to produce synthetic diamonds. The first synthetic diamonds were manufactured in 1953. Economically produced synthetic diamonds are 1 to 10 µm in size, but in this size range, they are totally unsuitable for industrial applications. In 1972, General Electric Co. developed a process to sinter the artificially developed, minuscule diamond particles into usable products. In this process, several layers of diamond-particles-and cobalt mixture are overlaid on WC substrates and sintered at 2,350° F and 1,000,000 psi. The final product is known as PDC. Today, PDC's are available in many shapes, but their size is limited to 3/4 in, or less, in length or diameter, because pressures greater than 1,000,000 psi are required to manufacture larger PDC's. At present, diamond and PDC arc the hardest and strongest commercial materials available for wear surfaces. The PDC used in this study had a hardness 3.61 times greater than that of WC.

Jan 1, 1992

Improve surface mine haul-age truck safety and efficiency by providing a means for sensing the weight and distribution of the truck's load. Approach The safety hazards and the economic implications of overloading mine-haulage trucks were analyzed to determine the net effect of that practice on mine operations. The analysis indicated that: Ten to 25 pct overloading is typical; Higher haulage, tire, and maintenance costs occur due to overloading (a 20 pct overload was estimated to increase operating costs 7 pct per ton); Ten to 15 pct of haulage? truck injuries and fatalities are attributable to overload conditions, at a cost over one million dollars per year to the mining industry. Vehicle-weighing technology that conformed to the performance specification for an off-highway haulage truck overload detection system was selected for in-mine testing. How It Works Normally, volumetric estimates are made during the loading sequence which do not account for the varying ore density. Hence, the actual weight of a load is never precisely known. By providing a precise measurement, an overload detection system will not only indicate vehicle overloading, but will also show under-utilization of the truck. One system tested by the Bureau of Mines was the ?Load Analyzer" manufactured by Pactronics Corporation in California. This system consists of a meter-type analog readout for the cab console and three "Electrosensors" (linear variable differential transformers) attached to the main frame. Using conventional welding and brazing techniques, two sensors are attached between the front members of the engine sub-frame and the top of the left and right trailing arms (one sensor per arm). The same techniques are used to attach the third sensor to the rear centerline of the truck. between the main frame cross member and the A-frame. The readout unit on the cab console indicates by color-coding whether each sensor loading is under (green), at (yellow), or over (red) the pre-set rated load. The three-sensor configuration with in-dependent readouts also detects uneven distribution of the load.

Jan 1, 1984

By W. A. Cole

The sulfur shortage that existed during the Korean conflict stimulated interest in coal measures as possible sources of sulfur. One of the areas brought to the attention of the Bureau of Mines was in Marion County, Iowa, where comparatively high-sulfur coals and other marcasite-bearing strata were known to occur. A Bureau of Mines engineer inspected the marcasite occurrence on December 4, 1954; this prompted further work on the Iowa coals and associated formations as a source of iron sulfides. An investigation of the Iowa high-sulfur coals was undertaken including core drilling, field reconnaissance, and compilation of data pertinent to consideration of the following: 1. Upgrading Iowa coal by mechanical cleaning and the feasibility of recovering sulfur from coal brasses. 2. Possibility of processing the high-sulfur coals by adaptation of methods employed in processing industrial gases to produce sulfur and sulfur products. 3. Possibility of finding concentrations of iron sulfides in associated rock formations in sufficient quantity for economical recovery.

Jan 1, 1957

By Foster Fraas

A method is presented for the linear evaluation of adsorption data using the equations dC = Ae-rv dv and v = [jT] - q, where dC is the phase composition increment, v a calculated parameter, T the absolute temperature, and A, r, h, g, and q the constants. The value of v is calculated from the composition C for both the adsorption surface and the immersion phase. A plot of v for each phase on Cartesian coordinates results in straight line graphs. With temperature variation, a plot of v versus,[ ] also results in straight line graphs. The equations are applicable to electronic and salt equilibria.

Jan 1, 1962

By F. D. Wang

The Bureau of Mines has developed a computer program for evaluating pit slope stability by the finite element stress analysis and limiting equilibrium method. The program includes the finite element method of stress analysis using triangular elements, finite-element model mesh generation, plotting of the model mesh and stress contours, calculation of a factor of safety along a circular or a plane failure surface, and location of a critical circular failure surface. Instructions for preparation of input data, an example problem, and the program listing are presented.

Jan 1, 1972

By S. J. Hussey

The Bureau of Mines investigated the applicability of carbon-in-pulp pro-cess for recovering silver from low-grade ores. The reasons for the research were (1) to illustrate a practical procedure for the process design of carbon-in-pulp adsorption circuits using leach slurries and simple equipment; and (2) to illustrate how equations of adsorption theory relating rate data and equilibrium adsorption curves can be helpful in process design. Carbon-in-pulp silver adsorption tests were made on Banner, Idaho; mine-run ore samples with silver contents ranging from 2.0 to 8.5 oz/ton and variations in cyanide leach extraction from 48 to 93 pet. The lower recoveries were attributed to the presence of complex silver sulfide minerals. Carbon-in-pulp batch adsorption tests provided rate data for the estimation of a silver equilibrium adsorption curve. Process design procedures in which the rate data were related to an equilibrium adsorption curvey by equations of adsorption theory were used to plan a four-stage pilot plant cascade. The pilot plant was successfully operated for 45 hr of countercurrent flow, producing a carbon product containing a mean silver loading of 571 oz/ton from a pregnant solution of 1.7 oz/ton of silver. Virtually all of the dissolved silver was recovered on the carbon.

Jan 1, 1978

By Robert J. Timko, Edward D. Thimons

Sulfur hexafluoride (SF6) is an odorless, colorless, nontoxic gas that has found acceptance as a tracer gas in research on ventilation pat- terns, measurement of air leak rates, respirable dust reductions due to bagging hood modifications, and the study of airflows relating to gob boreholes. Following a short review of the SF6 sampling technique, this report describes recent Bureau of Mines projects in which SF6 was used successfully as a tracer gas, enabling researchers to acquire representative data quickly and inexpensively.

Jan 1, 1982

By W. K. Sawyer

In this Bureau of Mines investigation, one-and two-dimensional gas reservoir simulators were combined in such a manner that pressure distributions both in an induced vertical fracture and in the surrounding formation, could be determined as a function of time for any specified well production rate. The technique used consisted basically of the alternate ust of one-and two-dimensional algorithms for obtaining new pressure distributions in the fracture and in the reservoir, respectively. The pressures at adjacent reservoir and fracture nodes were used to calculate flow rates from the formation into the fracture, which provided source terms for both algorithms. The combination model developed provides the only known means of simultaneously simulating transient gas flow in a vertical fracture and the surrounding formation. Thus, the technique developed would be useful in locating wells in a gas storage field in that the effects of both fracture length and conductivity could be considered prior to drilling and fracturing operations. In addition, it will be helpful in analyzing pressure drawdown tests in a vertically fractured gas well since the entire test can be readily simulated for a wide range of reservoir and fracture properties.

Jan 1, 1974