Search Documents

By R. T. Artz

Disposal of sewage is an important part of mine sanitation. Improper... handling and.disposing of sewagerare conducive to the spread of disease and often add foul and nauseating odors to the mine air. The diseases spread by unsafe methods of disposing of waste in mines are typhoid fever, cholera, amebic dysentery, hookworm, and other intestinal diseases due to parasites. Sanitary toilet facilities, with a good sewage-disposal system, each maintained in good order at all times, should help to prevent the spread of diseases transmitted by intestinal body wastos. The metal and nonmetal-mining industries have recognized the impor-dma tance and need for disposing sewage properly; accordingly, facilities of some sort are installed and need today in most large mines. The coal-mining industry has given little thought to the disposal of sewage underground; however, in most mines of the anthracite industry, the inflow of large vol- unes of highly acid mine water and the extensive drainage system required to remove this water provide a natural means for disposing of sewage.

Dec 1, 1946

By L. C. IlsLey

The first thing to consider in prevention of electric shock is the voltage of the circuit. No person can be sure that he will not be killed, even from a 110-volt circuit, if he makes proper contact with the circuit so as to cause the maximum current to pass through his body. As the voltage is increased to 250 volts, 500 volts, or 2,300 volts the danger from contact with the electric circuit is increased, Alternating current of the same nominal voltage is possibly more dangerous than direct current. Experience has taught us that both will cause death, and that if the fatalities from this source are to be kept low, certain precautions in the guarding of circuits must be observed.

Feb 1, 1929

By E. J. Matson

"SUMMARYThe Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Projects were set up on only the most promising properties. A preliminary examination of the Rio Grande property was made by Bureau of Mines engineers in July 1942 and the property was examined again in July 1943.The Geophysical Branch of the Bureau undertook a Geophysical survey of the area in November 1943 and was intermittently active in the district until June 1946. The major portion of their work was done from June 191 to November 1945. Favorable areas for exploration were recommended by the Geophysical Branch of the Geological Survey, 3/ and all holes were drilled in them.Two projects were set up by the mining branch in an endeavor to find ore bodies on the strength of the geophysical information."

Sep 1, 1947

By E. D. Gardner

"Introduction Ore from stopes in metal mines is generally dumped or drawn into chutes or raises through which it passes by gravity to the haulage levels. Occasionally, and under some conditions quite frequently, the ore in a chute will wedge or hang and refuse to run. This hanging of the ore may be due to the packing of damp or clayey material, to boulders forming an arch, or to loose lagging or other timber becoming lodged in the chute.In drawing material from a loading chute it is drawn out a car at a time, and the intermittent flow of the material .increases its tendency to hang. When the obstruction in the chute is near or at the loading gate, the chute pullers start the ore by punching it with iron bars inserted through openings in the chute gate. When the obstruction is beyond reach of the bars, other means of starting the ore must be used.In some systems of mining, chutes or ore raises are built with timber as the stope extends upward. Generally, a manway is left alongside of the chutes, and when the ore hangs in a chute usually it can be started by a miner from the manway ladder by pounding on the timbers of the chute or by punching the ore with a bar inserted through small holes in the chute lining. Special methods of starting clogged ore, such as shaking a chain left hanging in the chute, are used at some places.In other systems of mining, ore passes or chutes are run through solid rock and when the ore hangs in one of these passes, either it must be blasted or else started from the top. Sometimes the ore can be started by running water into the top of the chute, but if the water does not start the ore moving, it must be blasted from underneath. This is done by detonating a bundle of cartridges under the obstruction in the chute or raise."

Jan 1, 1927

By Dale E. Wittmer

Nonoxide ceramic materials could substitute for high-temperature alloy steels containing imported critical and strategic materials such as cobalt, chromium, and nickel if their high-temperature properties can be improved. An important result of this substitution would be a reduction of the Nation&apos;s need for imports of critical and strategic materials. In this Bureau of Mines investigation, the primary objective was to produce high-purity u1trafine (particles <5 ~m equivalent spherical diameter (ESD)) alpha-silicon carbide (a-SiC) powders with improved high-temperature properties using the Bureau&apos;s patented turbo-milling process. A secondary objective was to determine the feasibility of using polymer mill construction materials as a means of eliminating metal contamination from the turbomill. U1trafine a-SiC powders with BET (Brunauer-Emmett-Te11er) surface areas from 30 to 35 m2/g (~0.06 ~m particle ESD) were produced in an all-polymer turbomi11. These high-purity powders (with I-pct Band I-pct C additions) hot-pressed to greater than 99 pct of their optimal density and exhibited properties commensurate with those of commercially available a-SiC. The most promising of the construction materials tested for the major wear surfaces of the turbomi11 was u1trahigh-mo1ecu1ar-weight (UHMW) polyethylene, a polymer thermoplastic.

Jan 1, 1984

By T. N. McVay

The various applications of beryllium and its compounds in atomic - energy technology and a growing recognition of possible increased utilization of the metal in the aircraft and space - missile fields have resulted in increased interest in domestic and world reserves of beryllium . Unfortunately, little dependable data on beryllium resources and reserves are available , as past consumption of the element has been small and only limited prospecting and exploration work has been done . The scarcity of resource information is attributed partly to the difficulty of recognizing beryllium minerals in the field . These minerals frequently do not have distinctive characteristics of specific gravity, color , or other physical properties , that enable ready identification by the average prospector . This is particularly true of fine - grained minerals . As a result , a simple field test for identifying beryllium- bearing rock is needed . Recognizing this , technologists of the Federal Bureau of Mines investigated several of the proposed qualitative chemical tests for beryllium . This report describes various modifications of one of these methods to make it more suitable for use in the field . In the modified method , duplicate samples are fluxed -- one with potassium bifluoride and one with potassium bisulfate -- followed by dissolution of salts in water , conversion of the solution to an alkaline condition, addition of morin , and examination of the solution for fluorescence under short -wave ultraviolet light . This method provides a fast , dependable field test for beryllium minerals containing as little as 0.2 percent beryl or its equivalent . The test involves no radiation hazards , and it can be performed by persons having no technical training ; therefore , it should be useful to prospectors in discovering beryllium mineralization .

Jul 1, 1960

By R. R. Sayers

The added hazards to mining incident to oil and gas wells penetrating the coal measures in proximity to mine workings , have long been recognized in those fields where the extraction of oil , gas , and coal , has been in progress for a number of years . The history of these fields is replete with stories of serious mine fires , explosions , and miraculous escapes from both fires and explosions due to either oil or gas finding its way into the mine workings through the strata , or by mining into an unknown or uncharted and abandoned oil or gas well that had not been properly plugged . The Director of the Bureau of Mines , in response to numerous requests from coal operators and oil and gas operators , called a meeting in 1913 to discuss necessary precationary measures to take when drilling oil or gas wells through workable coal beds and to try , if possible . to formulate a set of regulations that might serve as a guide to those persons preparing regulations covering the drilling of oil and gas wells in the various coal producing States . This meeting was attended by representatives of the coal , oil , and gas industries , State geologists , State mine inspectors , and representatives of the Bureau of Mines . A committee was appointed to prepare a set of regulations , which was later published as U.S.Bureau of Mines Technical Paper 53 ; the discussions and results of the meeting werepublished as U. S. Bureau of Mines Bulletin 65 . Later , the American Institute of Mining and Metallurgical Engineers appointed a committee to draft a model law for the use of the legislature of any State concerned . This committee made its report on April 27 , 1928 . Several of the coal mining States now have more or less comprehensive regulations governing the drilling of oil or gas wells through workable coal beds , others have regulations that are inadequate , while some have no regulations . The State of West Virginia recently enacted a law containing reg lations which are the result of a comprehensive and careful study of the problem .

Nov 1, 1929

By H. H. Schrenk, L. B. Berger, Robert L. Beatty

"INTRODUCTION Toxic oxides of nitrogen 5/ are formed or liberated in many industrial process and may constitute a definite hazard to the health of persons exposed to the atmospheres thus produced. Oxides of nitrogen occur in the gases involved in the use of explosives, in the gasoline products of welding operations in the exhaust of internal-combustion engines, in the vicinity of electrical discharges, in the combustion of nitrated materials, and in chemical process involving nitration or the use of nitric acid, Itis evident that oxides of nitrogen may constitute an occupational hazard in many industries, and therefore it is important that those concerned with the control of such hazards be equipped with a technique suitable for the determinations of oxides of nitrogen in the concentrations of,hygienic significance."

Feb 1, 1943

By Lowell B. Moon

Regardless of how a mineral deposit in first discovered or by whom, any mining enterprise based upon it must pass through a preliminary stage of exploration. The common understanding of ?exploration? among mining engineers is well-expressed by Jackson and Knaebel:3/ Exploration work ranges from that performed by the individual prospector employing only the simplest tool, and equipment to elaborate campaigns involving the expenditure of largo stuns of money end the use of churn- car diamond-drilling equipment, large test-pitting crews, or sometimes a regular mining organization. In any event, the object is to determine as accurately as possible, with the funds available, the size, shape, and other characteristics of the ore bodies and their average value or grade.

Jan 1, 1945

By Andrew B. Cecala

This U.S. Bureau of Mines report provides a detailed description of the Bureau-designed modified shearer clearer system. Engineering drawings are provided for all major components of this system. The modified shearer clearer system is a revised version of the original system and is intended to improve the ventilation around both cutting drums. The original shearer clearer technique was solely a dust control technique that has been effective in lowering shearer operators&apos; dust exposures. The technique uses a series of water sprays that not only knock down a portion of the dust cloud but also act as small fans that move a substantial amount of air and keep the dust cloud from dispersing over the shearer body. The modified version is composed of two additional spray blocks for improved air movement around both cutting drums, thus lowering methane levels and the likelihood of an ignition. A laboratory study performed with the modified version in a full-scale longwall gallery resulted in a 73-pet reduction in methane concentrations at the shearer machine for both cut directions. The air-moving capabilities of the system provide more turbulence at the cutting drums and reduce methane levels.

Jan 1, 1994

By A. U. Miller

The added hazards to mining incident to oil and gas wells penetrating the coal measures in proximity to mine workings , have long been recognized in those fields where the extraction of oil , gas , and coal , has been in progress for a number of years . The history of these fields is replete with stories of serious mine fires , explosions , and miraculous escapes from both fires and explosions due to either oil or gas finding its way into the mine workings through the strata , or by mining into an unknown or uncharted and abandoned oil or gas well that had not been properly plugged . The Director of the Bureau of Mines , in response to numerous requests from coal operators and oil and gas operators , called a meeting in 1913 to discuss necessary precationary measures to take when drilling oil or gas wells through workable coal beds and to try, if possible . to formulate a set of regulations that might serve as a guide to those persons preparing regulations covering the drilling of oil and gas wells in the various coal producing States . This meeting was attended by representatives of the coal , oil , and gas industries , State geologists , State mine inspectors , and representatives of the Bureau of Mines . A committee was appointed to prepare a set of regulations , which was later published as U.S.Bureau of Mines Technical Paper 53 ; the discussions and results of the meeting werepublished as U. S. Bureau of Mines Bulletin 65 . Later , the American Institute of Mining and Metallurgical Engineers appointed a committee to draft a model law for the use of the legislature of any State concerned . This committee made its report on April 27 , 1928 . Several of the coal mining States now have more or less comprehensive regulations governing the drilling of oil or gas wells through workable coal beds , others have regulations that are inadequate , while some have no regulations . The State of West Virginia recently enacted a law containing reg lations which are the result of a comprehensive and careful study of the problem .

Nov 1, 1929

By W. D. Ryan

Industry must be made to realize that "Safety First" means just that - safety first. The miner must realize that safety first takes precedence over earnings. The employer must realize that safety is the first consideration, and is not to be subordinated to profit-making. Neither employee nor employer is justified in adopting the principle of safety first with reservations; that is they will practice safety first only so long as they think that it does not interfere with earnings or profits. This paper proposes to demonstrate that suberdinating safety to possible profit is short-sighted and that over an ex- tended period of time it dres not result in increased profits or earnings. An employee through disregard of safe practice may receive an injury that will cause him a loss of earnings if, indeed, he is net killed or permanently in- capacitated. If permanently incapacitated any compensation he may receive is very likely to be wholly inadequate as compared with probable earnings if the accident had not cccurred. The employer, upon his part, will find that the burden of compensating his injured employse will far exceed the outlay of money necessary to maintain a reasonable program of safety in his mine or plant. The mine foreman is one of the most important factors in the matter of mine safety. A vigilant and competent mine foreman, once he has established the confidence of the employees in his ability as a foreman, can be of invalu- able assistance in promoting mine safety, for through him and his assistants the employees may be made to cooperate. Every employer should remember, then, that the soluction of the foremen and their assistants is one of the most important matters connected with the work of establishing the maximum amount of safety in his mine. Everyone connected with the mining industry must be made to realize that there is to be no back-sliding and no let-up in safety work; that no matter how dry and tedious the routine may seem it is absolutely essential and justi- fied for both humanitarian and economical reasons. Efficient safety effort pays dividends in actual cash to both employer and employee. About 50 per cent of underground accidents in coal mines take place at the working face where the miners dig and load the coal. Approximately 17 per cent of coal-mine fatal accidents are the result of underground haulage. Face and haulage accidents can and will be reduced materially if the individual miner takes all precautions necessary to protect himself and if the management

Jun 1, 1930

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the eleventh. The-data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each halt township is followed by a description of each deposit developed in that halt township. The 14 halt-township maps and 77 detail maps of the bauxite deposits in this series at reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained tram the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion of that area.

Jan 1, 1948

By Michael A. Evanto, George J. Karabin

The Mine Safety and Health Administration, Pittsburgh Safety and Health Technology Center, Roof Control Division, is routinely involved in the evaluation of ground conditions in underground coal mines. Assessing the stability of mined areas and the compatibility of mining plans with existing conditions is essential to ensuring a safe working environment for mine workers at a given site. Since 1985, the Roof Control Division has successfully used the boundary-element method of numerical modeling to aid in the resolution of complex ground control problems. This paper presents an overview of the modeling methodology and details of techniques currently used to generate coal seam, rock mass, and gob backfill input data. A summary of coal and rock properties used in numerous successful evaluations throughout the United States is included, and a set of deterioration indices that can aid in the quantification of in-mine ground conditions and verification of model accuracy is introduced. Finally, a case study is detailed that typifies the complexity of mining situations analyzed and illustrates various techniques that can be used to evaluate prospective design alternatives.

Jan 5, 1999

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

APPENDIX G TABLE IX MINE A 1 General Total Employees 3000 Maximum No, of Men Underground/Shift 800 Shifts/Day 3 Type of Ore Copper Daily Production (TPD) 25,000 Mining Method Room and Pillar Vein Dip/Thickness l0°/l5 ft Number of Levels/Max Depth 1/0 to 1800 ft 2 Haulage, Conveyances and Travelway Main Haulage Rubber Tire/10 miles belts Man-Ways - Typical Route of Travel to most Remote Sites Rubber Tired Vehicles Hoists - Capacity/Speed/Depth Depth under construction 3 Ventilation 2,500,000 cfm - 5 surface fans 4 Compressed Air N/A cfm 10" and 12" lines 5 Incendiary Storage 2 day powder 1000 gal fuel oil 6 Communications 1 complete system - all shops, dinner areas, and feeder/breaker stations 2 partial systems 7 Escapeway- Systems Man Check System Section boss log and punch cards Alarm System Mine phones with paging system Posting of Escape Route Maps No Escape Signs Every intersection, fluorescent paint Evacuation Drills 2/yr/shift Refuge Chambers - 1 cinder block - No longer required

Jan 1, 1976

Identify abnormal low-frequency blast vibrations. Develop blast design procedures for such adverse vibration cases, including the selection of delay times based on ground conditions, vibration frequency, and structural response. The Problem Research by the Bureau of Mines and others has demonstrated how structural response and the potential for cracking and other damage depends on blast vibration frequency in addition to particle velocity amplitude. The Bureau has published recommended criteria for blasting near low-rise residential-type structures; criteria that specified frequency-dependent amplitudes. The typical vibration frequency from surface mine and quarry blasting is 20 hertz (Hz). Sites have been found, however, that regularly produce ground-roll-type waves with frequencies as low as 4 Hz. The most serious cases arc those where vibration frequencies fall in the natural frequency range for structures of 4 to 12 Hz. Such vibrations have a higher potential for causing, damage to residential structures, particularly at the low end of this frequency range, because of the resulting high strains these frequencies produce in structural materials.

Jan 1, 1990

By Ronald D. Hill, Elmore C. Grim

Mining as an extractive process alone is outdated and unacceptable to today&apos;s environmentally concerned public. Multiple land use must be considered as well. Only through effective preplanning can the full potential of reclamation result in a lasting asset for future generations. The coal industry is now recognizing that reclamation of mined lands is part of the mining cycle that must be planned and carried out in a timely and orderly manner. It is also finding that planning reclamation in advance of mining is cheaper and more effective than waiting until mining is completed. The decision to open a strip mine must be based on the results of studies to determine if successful reclamation can be achieved and whether the economic benefits to the company will be justified(1). Information regarding the physical, chemical, hydrologic and biologic systems operative at the site must be under- stood or reclamation will be a failure. Working together, engineers, management and reclamation specialists should design the actual mining and reclamation plan before mining is begun.

Jan 1, 1974

Determine the extent to which remote-sensing techniques, primarily lineament analysis, can be used to identify geologic structures that may affect the location and migration of subsidence over abandoned underground coal mines in the Colorado Springs, CO, area. Compile data using a geographic information system (GIS) to allow efficient and reproducible comparisons and analyses. Background The basis for evaluating abandoned mine land (AML) sites with remote-sensing techniques comes from past and ongoing Bureau ground control research using remote-sensing data to identify potential hazards caused by geologic structures (faults, joints, etc.) above active underground coal mines. Research showed that lineament (linear feature) analysis of Landsat Multispectral Scanner (MSS) images could indicate locations of fractures and fracture trends that had varying, but significant, impacts on the stability of mine openings. Such geologic structures should be identifiable over abandoned mines as well. If fractures are present, even if they arc not faults, they should represent areas of potential instability over these mines and, therefore, should tend to localize subsidence when it occurs, particularly for deep and moderately deep portions of mines.

Jan 1, 1992

By David C. Oyler, Herbert H. Fields, William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to sup- port the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

By John Jordan, Steven J. Knoll, Douglas Tesarik, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004