Search Documents

By Van H. Manning

Of all the war work by the Bureau of Mines none ultimately covered such a variety of processes and equipment, employed as many men, or called for as large an outlay as that started in con- nection with the solution of problems relating to the use of noxious gases in warfare. Beginning with an investigation to develop the best type of gas mask, the scope of the work extended until it included researches relating to a wide range of devices, such as different types of poisonous and irritating gases and smokes, smoke screens, gas shells and gas bombs, flame throwers, trench projectors for firing gas bombs, signal lights, and incendiary bombs. The Bureau of Mines in starting this work selected the necessary personnel, pro- cured the early equipment, and for some months, from the begin- ning to June 30, 1917, paid the cost of the work from its own funds. The Bureau of Mines built up a research staff of more than 700 chemists, including many of the most prominent chemists in the country, and obtained the cooperation of many of the universities and chemical companies. When the results obtained through this research were to be applied by the War Department, the Director of the Bureau of Mines cooperated in the selection of men to have charge of manufacture or further development, recommending chemiste who subsequently received commissions in the Army. The personal cooperation with the War Department was thus very close. The bureau can fairly claim that because it started this work on gas warfare and received the hearty support of the Department of War, the Navy Department, the National Research Council, and State, educational, and private institutions, the country was in July, 1918, months ahead of where it would otherwise have been in the production of gas masks and other devices. The production of toxic gases then far exceeded the supply of shells. In addition the later work in gas-mask manufacture by the Surgeon General's Office of the Army, which resulted in the development of the best mask produced anywhere; in gas manufacture and gas proving-ground tests by the Bureau of Ordnance, and in the chemical warfare pro- gram of the Navy, including the use of smoke screens, shells and toxic gases, were the direct results of the bureau's experimental work. The American charcoal and soda lime, developed through the research work, are the best used by any nation. The Bureau of Mines was instrumental in developing satisfactory methods of manu- facturing chlorpicrin, phosgene, mustard gas, brombenzylcyanide, cyanogen chloride, and other noxious substances on a large scale. The bureau also developed a smoke funnel for the Navy which no doubt saved many ships from submarine attacks, and devised smoke barrages, signal lights, incendiary darts, etc., for the Army. The Ordnance Department of the Army asked for incendiary bombs and were furnished with bombs better than any made previously. Perhaps the greatest single result of the research work has been the demonstration of the value of the services that the chemist and chemical engineer can render in time of need and the recogni- tion of chemical investigations as a necessary function of the Gov- ernment.

Jan 1, 1919

[Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand .for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States. Accordingly, the 74th Congress appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions and hearing2/ relative to the need for the sway, the opinion ms expressed that crude oil held in storage for long periods had lost so much of its gasoline content that he economic significant of total stocks should be discounted materially. Therefore, a primary objective of the survey was to]

Jan 1, 1938

Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States. Accordingly, the 74th Congress -appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions end hearings2/ relative to the need for the survey, the opinion was expressed that crude oil held is storage for long periods had lost so much of its gasoline content that the economic significance of total stocks should be discounted materially. Therefore, a primary objective of the survey was to

Jan 1, 1938

By Scott Turner

We are here today to witness the graduation of 63 young men as Engineers in the mineral industries . It is an important occasion and one in which the public takes a keen interest , since this school has long been famous for the educational facilities it affords young men, and for the high professional standing of its graduates . : : : It is fitting that once each year we should pause to review the path the student has traveled , and to reflect upon the perspective opening before him as an engineer . I was invited to come from Washington to take part in this ceremony and to say something to these young graduates . In searching for a theme ," it occurred to me. that perhaps my best contribution would be to duscuss certain beliefs as to college training , deal with the situation in which the young engineer finds himself on graduation , touch on the new ideas of the social and political responsibilities of the engineer , and point out what he may expect to find in practice , and , above all , what he must do to orient himself properly in the mining profession and maintain the best traditions of our brotherhood . Let us first review your college days and see what they have done for you . I am told there are still many temptations in college . I know there used to be . Rest assured the same holds true in the professional life ahead of you. The main difference is , perhaps , that your greatest temptations in college were those offered by your teachers , who tried to entice you into realms of harder work, closer application , increased concentration , clearer thinking and better understanding , by animating your curiosity and increasing your powers of reasoning and of observation . In other words , here you have carefully and systematically been decoyed toward finer and loftier things . Do not expect that similar helpful influences will greet you on every side in your professional life . Often quite the contrary is the case .

Oct 1, 1930

By George A. Bell

This paper reviewing the leaching practice of the New Cornelia mines of the Calumet & Arizona Mining Co. at Ajo, Ariz., is the first of a series being prepared by the Bureau of Mines on leaching methods and costs in the various mining districts. ACKNOWLEDGMENTS The author acknowledges the assistance of T. G. Chapman, consulting engineer, and E. D. Gardner, supervising engineer of the Southwest Experiment Station, Bureau of Mines, Tucson, Ariz.

Jan 1, 1930

By J. V. Batty

The Bureau of Mines devised techniques involving the use of beta-and gamma-ray-emitting radioisotopes and successfully adapted these techniques to the density of mineralized flotation froths) the rate of flow of finely ground ore pulps) and the residence time of pulps in processing circuits. Specifically, the water and mineral loads of flotation froths were continuously measured by determining the proportion of a constant-strength beam of beta rays that was absorbed by the froth column. Continuous measurement of the rate of flow of an ore pulp was accomplished by measuring the changing width of a free-falling stream of the pulp with a collimated beam of beta rays. The residence time of solids in conditioning and resin-in-pulp circuits was accurately measured by following the progress through these circuits of a portion of the pulp that had been tagged with the gamma-emitting Ag110 radioisotope.

Jan 1, 1966

By B. J. Scheiner

Oxidation procedures based on the chlorine-hypochlorite system were investigated for improving gold recovery from carbonaceous gold ores. The oxidation pretreatment prior to cyanidation was accomplished by (1) addition of sodium hypochlorite to ore pulp, (2) by addition of chlorine to ore pulp, and (3) by generation of hypochlorite in situ by electrolysis of a brine solution used to pulp the ore. Gold extraction of 90 pct was achieved by cyanidation of carbonaceous ore that had been pretreated with 20 Ib per ton sodium hypochlorite at 50° C for 4 hours. Similarly, pretreatment of the ore pulp with 35 1b chlorine per ton at 24° to 30° C and 15 hours reaction time resulted in 89-pct gold extraction by subsequent cyanidation. Concomitant studies showed that electrolyzing the pulp prepared with a brine solution was equally as effective as electrolyzing hypochlorite and chlorine for oxidizing carbonaceous ore constituents that are deleterious to cyanidation. Gold extraction of 90 pct was obtained by electrolysis when 275 lb of are was treated at 200 amp for 7 hours in an 8-to 10-pct salt solution. Power consumption was in the range of 60 kwhr per ton.

Jan 1, 1972

By W. J. Fene, G. W. Grove

An important activity of the Safety Division of the Bureau of Mines , in its efforts to reduce accidents , is the safety inspection of mines . Inspections are made at the request of the operators and are not connected with the inspections by the various State departments of mines . The operating management is furnished with a confidential report of the results of the Bureau's inspections , with recommendations for elimination of the hazards found . These mine - safety inspections include a study of mining practices , conditions , and equipment and in some cases the sampling and analysis of mine air and coal dust . The Bureau of Mines has no regulatory powers , therefore the recommendations made in these reports are merely suggestions , and operators are not required to adopt them . Mine inspections are a check on safety standards , methods , and practices and are essential to any accident -prevention program . A foreman or superintendent may be sincere in his efforts to operate a mine safely and believe that he has done everything possible to attain this end . However , experience has shown that because of his familiarity with the mine and the consequent " nearness " of its various features many unsafe conditions may be , and in most cases are , overlooked ; an inspector , particularly an outsider who is trained to look for hazards , can point out the unsafe conditions overlooked by the foreman or superintendent . Some companies employ safety engineers who make regular inspections of their mines , report substandard conditions and hazards found , and make recommendations for correcting them . Unless these recommendations are carried out the inspections have little value . In making recommendations , due consideration should be given to the feasibility of carrying them out ; the management may and very often does consider a recommendation impracticable because of the

Mar 1, 1935

By Herbert M. Wilson

The act (36 Stat., 369) that established the Bureau of Mines in the Department of the Interior defined as part of the bureau's province and duty the making of "diligent investigation of the methods of mining, especially in relation to safety of miners and the appliances best adapted to prevent accidents," and it authorized the bureau from time to time to make such public reports of its work and investiga- tions as the Secretary of the Department of the Interior may direct, with the recommendations of the bureau. The national mine-rescue and first-aid conference was projected in the hope that it would be a factor in increasing safety in the mining industry through the recommendation of better and safer methods of conducting mine-rescue operations, more efficient methods of extend- ing and giving training in the use of artificial-breathing apparatus, and approved and more effective methods of administering first aid to injured miners and of training miners in first-aid work. The bureau feels warranted in publishing the resolutions adopted by the conference as a guide to mine workers and others concerned in obtaining greater safety in mining, and in presenting such extracts from the discussion as indicate the reason for the adoption of any particular method. In issuing this bulletin, however, the bureau does not indorse these resolutions in whole or in part as a final ex- pression of its views regarding the best method or procedure in any case. It does believe, however, that the resolutions furnish an excel- lent starting point from which to develop a standard code of pro- cedure in mine-rescue and first-aid work. It will be noted that in some important cases further information is necessary before any standard procedure can be recommended, par- ticularly as regards types of bandages, methods of resuscitation, the use of stimulants, the cumulative effect of poisonous gases, the diet of men engaged in rescue work, the physiologic effect of the pressure

Jan 1, 1913

By T. L. Joseph

"IntroductionThe efficiency of ore reduction in the blast furnace and fuel requirements depend upon the degree of uniformity with which reducing gases can be distributed through the stock column and upon the permeability of individual pieces of ore and sinter. If the ore is fine, the major problem in reduction is to get the ascending gas stream to the surface of the ore-Hard, dense ores of low permeability, mined in coarse sizes, tend to improve the permeability of the bed, but unless they are crushed to the proper size they reach the hearth unreduced.Surveys by the Bureau of Mines have shown conclusively that the gas distribution in the upper three fourths of the furnace is far from ideal. Furnace lines, top design, and methods of charging are important, but more thorough size preparation of the ore is necessary to eliminate size segregation at the stock line, which inevitably leads to non-uniformities in gas distribution.Because of the quantity of sinter now produced close study of the characteristics which determine its behavior in smelting is warranted. As the use of concentrates increases agglomeration will become more of a necessity. Improvements in the physical character of the ore burden are particularly important to plants using coke of poor physical quality. In addition to aiding reduction, improved physical properties of the ore burden will permit the use of higher blast heats, which is equally important.Reduction Tests on Fine Sizes of SinterPrevious reduction tests on minus 0.742— plus 0.525--inch pieces of commercial sinters revealed large differences in porosity and reducibility. The results have been published in a former report. 3 Although the physical properties of the sinter, particularly porosity, were found to be of major importance in determining the rate of deoxidization, it appeared that certain chemical properties of the sinter appreciably retarded the reduction of sinters high in silica. This was attributed to the presence of fayalite, which has been identified by Schwartz and by Luyken and Kraeber4 as an important constituent of sinter. Although furnace operators and metallurgists have assumed that iron silicate is more difficult to reduce than hematite or magnetite, definite data on the reduction characteristics of this material were not available. Tests were undertaken, therefore, to develop a method for de-termining the amount of iron silicate present in sinters so that its effect upon reduction could be observed."

Jun 1, 1934

By Allan J. Clark

This paper, describing the milling practice of the Homestake Mining Co., is one of a series being prepared by the Bureau of Mines. The author acknowledges the assistance of T. G. Chapman, one of the consulting engineers of the Bureau of Mines, in arranging this paper for publication.

Jan 1, 1931

By Fred C. Turin, Sean Gallagher, Kim M. Cornelius, William J. Wiehagen

An important part of initiating a site-wide ergonomics evaluation process is prioritizing jobs to be analyzed. While injury data is important, other factors such as worker discomfort and physical exertion requirements, should be considered. This paper describes the use of four sources of data (injury records, the Nordic Standardized Musculoskeletal Questionnaire, supervisor interviews, and management concerns) to prioritize jobs for ergonomic analysis. The approach described integrates the four sources using a decision matrix to prioritize jobs for ergonomics analysis.

By R. F. Abernethy

Recent investigations in the United States and in other countries have produced considerable information on the nature and occurrence of minor elements in coal. The possibility of recovering certain elements, particularly germanium and uranium, from coal ash and other coal products has received considerable attention. Some flue dusts are potential sources of germanium, and certain lignite deposits are potential sources of uranium, but industrial recovery of these elements has been limited to small quantities for technical and economic reasons. Considering the large amount of coal mined annually, a small percentage of a rare element may have industrial significance if an economical method of recovery can be developed. In 1944 information on the occurrence of rare elements in coal was reviewed in Bureau of Mines Technical Paper 669 (46).3 This report is a revision of that paper with the view of summarizing published information available for United States coals, and pertinent information concerning coals of other countries. Selected references from the original paper are retained. New references do not include all preliminary reports when more permanent literature describing complete projects is available. Consequently, the list of references should not be considered complete.

Jan 1, 1963

By R. E. Cumings

The Bureau of Mines made electrorefining tests in inert-atmosphere, molten salt cells to develop methods for the preparation of high-purity molybdenum. Seven of the electrolytes investigated were suitable for the preparation of refined metal. The electrolytes were composed of molybdenum chloride in alkali chlorides or mixtures of alkali and alkaline-earth chlorides. An electrolyte composed of potassium chloride and potassium hexachloro-molybdate was selected for a larger scale, more detailed study on the basis of its ease of preparation, its ability to retain the molybdenum salt, and the type of deposits obtained. High-purity molybdenum in the 99.99-percent-purity range was successfully prepared as dense plate up to 80 mils thick and as dendritic crystals. The temperature of electrolysis and the current density were major factors in determining whether plate or dendritic crystals of molybdenum were obtained.

Jan 1, 1966

By S. L. May

The Bureau of Mines has developed several methods for extracting tantalum and columbium (niobium) and the rare-earth compounds from ores and concentrates. A cooperative agreement was made by the Bureau with Porter Bros. Corporation of Idaho to process 200 pounds of its euxenite concentrate by methods that had been developed at the Albany, Oreg., Metallurgy Research Center. The euxenite concentrate was processed to extract and purify the valuable metals by chlorination, solvent extraction, and hydrometallurgical techniques. Chlorination was used to convert the valuable constituents into chlorides and to partly separate them. Solvent extraction techniques were used to separate the tantalum from the columbium. The rare-earth and uranium compounds were purified by hydrometallurgical methods.

Jan 1, 1959

By F. E. Block, Robert R. Brown, A. W. Henderson

The chlorination of Cr₂ 03 (chromic oxide ) in the presence of carbon with CC14 (carbon tetrachloride ) and COCl2 (phosgene ) chlorinating agents was investigated by employing the radioactive tracer carbon By tagging carbon mixed with Cr₂ 0з , the chlorination reaction was evaluated in terms of the competitive reaction of the elemental carbon and the carbon contained by the chlorinating agent . A unique gas - analysis train was used to separate the chlorination product gases ; CO , CO₂ , and COC12 . The C¹ activity of the gases was determined and used to calculate the reactivity of each source of carbon . Reactivities were determined for the temperature range from 600 ° to 900 ° C. The results of the investigation show that each source of carbon reacts significantly with the Cr2 03 and that the reactivity of each form of carbon depends on the reaction temperature , and each form is independent of the other . Radioisotope and gas - analysis techniques are discussed and a description of the experimental apparatus is given .

Jan 1, 1964

By Charles E. Whieldon, C. I. Pierce

Data on the oilfields in Mahoning , Columbiana , Carroll , Jefferson , and Harrison Counties , Ohio , were collected from scattered sources and compiled to make the information readily available to operators who may be interested in conducting secondary - recovery operations in the area . General geology , oil production , oil - productive acreage , core data , reservoir calculations by townships , and miscellaneous data and reference material are presented .

Jan 1, 1965

By Jos. R. Guiteras

This paper describes the pumping operations at the Ajax, Cresson, and Vindicator dines in the Cripple Creek mining district of Colorado during the summer of 1936. At that time the three mines wore pumping 6,500 gallons of water per minute into the Roosevelt drainage tunnel. Cripple Creek is the most important gold district in the State; it has yielded gold valued at over $365,000,000. The mines engaged in pumping are among the largest producing properties in the district. ACKNOWLEDGMENTS The author wishes to acknowledge the friendly cooperation of mine officials at the properties visited. At the. Ajax mine information was courteously given by Clayton Kissel, mine superintendent, and his staff; R. Y. Roby contributed the drawings. For information on the Cresson mine, thanks are expressed to Al H. Bebee, mine superintendent, and his staff, especially to Guy Rorabaugh, master mechanic, and to engineer Carlton. At the Vindicator mine, J. S. Anderson; mine superintendent, and Robert Welch, master mechanic, assisted; the latter furnished most of the information about that mine. Acknowledgment is also made of the cooperation of M. H. Salsbury, engineer at the Portland mine, who supplied technical data on the Roosevelt drainage tunnel.

Jan 1, 1937

By D. H. Zellers

Since its inception the United States Bureau of Mines has fostered the development of portable mine lamps. Although there is still much to be desired with respect to illumination in coal and metal mines and the replacement of open lights has been slow the Bureau has been given credit for assisting materially in the development and introduction of the safe and efficient portable mine-lighting equipment available today. Much of the work conducted by the electrical section of the Bureau entails approval tests of various types of electrical equipment, including lamps; to be used in atmospheres that may contain methane or coal dust in explosive proportion. If a can lamp meets the requirements-for safety, efficiency, and adequacy, as published in Schedule 6B,4 it is approved and is generally known as a "permissible" lamp. The terms "approved" and '"permissible' often are used interchangeably. The manufacturer must put an approval plate on each approved lamp, showing it has mot the schedule requirements. The approval plate is not a guarantee that the lamp is safe. However, if the lamp, once in service, has not had any parts changed or improperly assembled or if carts that wear out or depreciate have been properly replaced it should still, be safe, efficient, and adequate for the service intended. Virtually all electric cap lamps in service today in the United States and a great many that have been sent to foreign countries bear the approval plate of the United States Bureau of Mines. Although many explosions have been attributed to open lights none has been charged against the permissible cap lamp. Nystagmus, a disease of the eye attributed to working under insufficient illumination, is practically unknown among; American miners, although it is quite prevalent among European miners.

Jan 1, 1935

By Frank E. Cash

The compensation-insurance rates for quarrying in North Carolina are 11 times higher than for the State?s major industry, textiles. Some operators are willing to accept this as representing the ratio of existing hazards. This was not true of the management of the Southern Aggregates Corporation, and in 1935 it tools definite steps to correct the idea of its local officials and employees that loss of life and limb in quarries is inevitable. ACKNOWLEDGMENTS The authors acknowledge gratefully the assistance and information concerning these operations furnished by H. M. Shaw, safety director (also secretary and treasurer), Southern Aggregates Corporation, Raleigh, N. C.; by the following superintendents: J. H. Rodgers, Blair Quarry, Blair, S. C.; J. D. Lane, Greystone and Rolesville Quarries, Henderson, N. C. ; J. H. Arthur, Guilquarry, Stokesdale, N. C.; J. H. Watkins, Rockton Quarry, Wendell, N. C.; P. A. Wellenborne, Reidsville Quarry, Reidsville, N. C.; and J. L. Kirchin, Woodleaf Quarry, Woodleaf, N. C.; by the various foremen at the plants, and by Murry Id. Grier, safety engineer, North Carolina Department of Labor, Asheville, N. C.

Jan 1, 1940