Search Documents

By John J. McClelland

The Bureau of Mines conducted a study of longwall plow operations to identify dust sources and existing control technology. Three longwalls employing either the high-speed overtaking or conventional method of mining were surveyed. Principal operating parameters and on-site dust control technology at the time of each survey are described. Short-term gravimetric and instantaneous sampling results are discussed in detail. The relationship between longwall dust levels and dust control technology was examined.

Jan 1, 1988

Reduce well construction and operation costs associated with in situ leach mining while increasing mineral recovery. Approach To accommodate the size of centrifugal pumps presently in use, in situ leaching production wells are typically drilled to 6 inches in diameter, while monitor wells are drilled to measure 4 inches in diameter. However, in order to reduce the cost of drilling these larger diameter wells and to increase recovery, the Bureau has developed jet pumps which have smaller diameters than centrifugal pumps of the same capacity. This allows both production and monitor wells to be drilled smaller. Bureau estimates indicate that the cost of drilling a 3-inch-diameter production well at in situ leaching operations would be about 35 percent less than the cost of a 6-inch well. Similarly, the cost of drilling a 2-inch-diameter monitor well would be about 26 percent less than the cost of a 4-inch well. Such significant savings in the cost of drilling these wells would effect a substantial reduction in total capital cost. Use of the new jet pumps can also increase the percentage of recovery because less costly wells allow closer well spacings, improving the distribution of the leach solution. How the System Works After the borehole is cased, the new small-diameter jet pump, along with piping and accessories, is installed and connected to a centrifugal pumping unit on the surface. High-pressure water from the surface pump is forced through a nozzle into the venturi of the jet type pump injector. This jet action lifts the leach and mineral-bearing solution to the surface.

Jan 1, 1984

By John E. Miller

A high accuracy Burnett apparatus for use at 12,000 psi and 0° to 65° C has been constructed at the Bureau of Mines Helium Research Center. The apparatus is patterned after Burnett's original apparatus, but the working pressure is much higher and elastic distortion can be essentially eliminated. An operating procedure to permit faster experimental measurements is suggested.

Jan 1, 1967

By Emery Chilton, Charles Taylor, Mark Senk, Linda McWilliams

Three-axis ultrasonic anemometers are used to study airflow in the NIOSH ventilation gallery where ventilation in an underground mine is simulated. In this study, performance characteristics of this anemometer are evaluated and the effects of sensor orientation and sampler location on flow readings are examined. The study results provide guidelines for more effective use of the ultrasonic anemometers in the ventilation gallery.

By F. C. Gibson

An electrical method for the continuous determination of propagation velocities in opaque, confined explosives, and propellants is described. A resistance element imbedded in the reactive material generates electrical signals that are displayed oscillographically and indicate the position and progress of a reactive zone associated with progress of a reactive zone associated with burning or detonation. The method is applicable to both solids and liquids.

Jan 1, 1963

By Michael G. Zabetakis, Glenn H. Damon, Joseph A. Herickes

The flammability and explosibility of unsymmetrical dimethylhydrazine ( UDMH ) were investigated by the Federal Bureau of Mines to evaluate hazards associated with commercial application of this material as a missile fuel . This program included the following determinations : 1. Temperature limits of flammability in air at one atmosphere pressure ; 2. limits of flammability at selected elevated temperatures and pressures ; 3. 4 . 5. spontaneous ignition temperature in air at one atmosphere and at 200 pressure per square inch gage ( p.s.i.g. ) initial pressure ; spontaneous decomposition temperatures in nitrogen at one atmosphere and at 200 p.s.i.g .; shock sensitivity over a temperature range from about ( ca. ) 25 ° to 50 ° C .; 6. shock sensitivity of reference propellants ( hydrazine , nitromethane , methyl acetylene , etc. ) ; 7 . shock sensitivity of UDMH plus small amounts of selected metal catalysts . Part of the corresponding data was obtained for a mixture of unsymmetrical - dimethylhydrazine and diethylenetriamine ( U - DETA) .

Jul 1, 1960

By R. T. Artz, Simpson. O. V.

"INTRODUCTION The provision of escapeways from coal mines is a moral and, in most States, a legal obligation of mine owners and operators. The obligation is not always fulfilled because of the hope that no occasion will ever arise requiring the use of such facilities, and, as time passes without the need for using them, a false sense of security is born in the belief that ""it can't happen here.""The disastrous fire in a mine in Ohio on July 5, 1944, again focused attention on the importance of escapeways in averting disasters and made it clear that one or more dependable exits must be provided from a mine and parts thereof where men might be trapped by being cut off from the regular travel route. This matter of always-having available travelable exits has been advocated for many years by the United States Bureau of Mines."

Aug 1, 1948

By F. A. Skirvin

Purification techniques were investigated for removing low-level metallic impurities from tungsten hexachloride. These techniques included distillation) fused-salt scrubbing) zone refining) and adsorption. Fractional distillation of tungsten hexachloride was found to be an effective purification method. The impurity levels of molybdenum) iron) nickel) copper) magnesium) and manganese were reduced to provide a tungsten halide sample which contained a total of less than 10 ppm detectable metallic impurities. Purification by fused-salt scrubbing of tungsten hexachloride in a lithium chloride-potassium chloride eutectic produced a hexachloride product which was of approximately the same quality as that obtained by distillation. Zone refining and adsorption did not appear to be as effective as distillation or fused-salt scrubbing.

Jan 1, 1967

By M. M. Fine

This Bureau of Mines report describes the theory, experimental procedures, and the results obtained to date in the development of the Bureau's process for magnetically roasting iron ores using scrap iron as a means of reduction. Since magnetic separation is an operational step common to magnetic taconite plants, the preliminary research studies emphasized only the novel magnetic roasting step. The studies included the use of automobile scrap, ferrous reductants such as borings and turnings, and prereduced pellets. Technical feasibility of the process was demonstrated both on a bench- and pilot-scale. Quality magnetic concentrates with recoveries of over 90 percent were obtained from a direct shipping ore containing 59.5 percent Fe and from fine grained semitaconites with about 30 percent Fe.

Jan 1, 1966

By J. H. Holden, G. R. Strimbeck, L. F. Willmott, W. R. Huff

A pilot - scale fluidized feeder was developed for continuously feeding up to 1 ton of pulverized coal per hour to a pressure gasifier . Fluidization in the 3 - foot - diameter by 34-1 / 2 - foot - high feeder is effected by two streams of inert gas , a technique called zone fluidization . A stream of inert gas through a drilled plate in the base of a central column near the bottom of the feeder fluidizes the coal . Another stream through a drilled plate in the annulus between the central column and feeder wall provides a source of semifluidized coal for the central column . Fluidized coal from the central column discharges through an extraction funnel and discharge line . Zone fluidization provided good fluidization with moderate requirement for fluidizing gas . Instruments were developed for metering and recording the flow rate of fluidized coal . A system was developed for storing , and weighing pulverized coal , and then delivering it in fluidized form at about 1 to 8 tons per hour .

Jan 1, 1964

By H. Kim, R. W. Plummer, T. J. Stobbe, W. G. Jones

"Exposure to airborne dust in coal mines has caused respiratory disease in coal miners. The causal agent in these diseases remains unknown, although the minerals found in and around the coal seam have been implicated. Toxicological studies designed to establish the effect of different mineral combinations and concentrations are lacking because the mineral content of coal mine dust has not been defined. This paper reports the initial results of a study done to characterize the mineral content of the coal mine dust found in a mine in the Upper Freepott seam in Northern West Virginia. Coal mine dust samples were collected using 4- stage cassette impactors at nine locations in the mine. The samples were analyzed by an x-ray microdiffraction film technique supplemented by energy dispersive scanning electron microscopy. Primary size modes of about 17 to 20 micrometers from the samples collected at the haulageway and the returnside of the continuous miner were found. From the returnside of the roof bolter samples, a primary size mode of 12to15 micrometers was measured. The minerals found in high percentages were illite, kaolinite, quartz, and calcite. The distribution of minerals in inter· and intra- location samples showed wide variations. Trends in these variations are presented. Stobbe, T. J.; Plummer, R. W.; Kim, H.; Jones. W.: Characterization of coal mine dust. Appl. Ind. Hyg. 2:95· 100; 1986. IntroductionDisease-associated dusts in coal mine environments continue to afflict miners in today's modern mines. The relationship between exposure to coal mine dust and the development of various respiratory diseases has been well recognized; however, the reasons for variation in occurrence of these diseases among miners in different geographic areas,(1) rank of coal seams,(2-3) and jobs (4) remain uncertain. Several papers have reported on the causal agent in the development of these diseases. Davis (5) found that the percentage of the non-coal minerals present in the lungs of deceased miners increased as the level oi pneumoconiosis became more severe. Reisner (6) reported that cell damage caused by coal mine dust increases with the mineral and quartz content of the dust and with the geo· logical age and rank of the coals. Two studies, investigating the in vitro effects of mineral dusts. reported by Seemayer and Manojlovic (7) also obtained positive correlation between cytotoxicity and the mineral content of coal mine dust. Gormly (8) postulated that destruction of macrophages by certain mineral dusts is the first step in the development of pneumoconiosis. In 1980, Adamis and Timar (9) reported that quartz. sandstone, slate. respirable colliery dust. bentonite, illite, and some kaolins had cytotoxic effects on rat peritoneal macrophages""in vitro."" Walton,(10) however, reported that the presence of high clay, illite, and kaolin mineral exposures reversed the hazards associated with increasing quartz exposures. This finding was supported by Le Bouffant and coworkers.(11) They reported that illite present in coal mine dust strongly inhibited the pathogenic effects of quartz while kaolin had a weaker inhibitory effect."

Mar 1, 1989

By Debra A. Griffith

The U.S. Bureau of Mines currently is researching the relationship between the level of back strength and the probability of low-back injury. This report is a review of the literature and statistics on over-exertion injuries. Overexertion continues to be a significant source of injury in metal and nonmetal mining, accounting for approximately 24 pct of all injuries yearly. These injuries, particularly to the lower back, can be very expensive in human and monetary terms. An examination of the accident data on overexertion injuries is necessary to provide a background for research into prevention and/or amelioration of those in-juries. The job categories outlined in the Accident Data Analysis data base most affected are "Mechanic/Electrician" and "Mill/Plant Worker." The age group most affected is "30-39" years, and the experience group most affected is "0-.99" years. The most prevalent type of overexertion injury is "Strain/Sprain," and the trunk is the body part most often involved in an overexertion injury.

Jan 1, 1994

By Alla D. Mah

The heats of combustion of three chromium carbides, Cr23C6, Cr7C3, and Cr3C2, were determined by combustion calorimetry. Heats of formation calculated from the results follow: ?Hf°298 (Cr23C6) = -94.7 ± 5.0 kcal/mole, ?Hf°298 (Cr7C3) = -43.3 ± 1.7 kcal/mole, and ?Hf°298 (Cr3C2) = -22.5 ± 0.8 kcal/mole.

Jan 1, 1969

By Robert T. Mann

This paper is one of a series being prepared for and published by the United States Bureau of Mines on the quarrying, crushing, and grinding of limestone for cement manufacture. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total coats. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. B. Thoenen, mining engineer of the Bureau of Mines, in the preparation of this paper.

Jan 1, 1933

By Manuel Gomez

Primary, low-temperature tars are generally known to alter with time. The effect is believed to occur, in some instances, without the external influence of air, light, or heat. Since one of the processes occurring during extended storage is oxidation, the action of mild oxidation induced by air and heat, in addition to the effect of storage, was studied. The principal effect in aging and oxidation is formation of pitch at the expense of the distillate fraction. The fraction boiling above 270° C. is mainly involved in pitch formation due to storage, whereas all fractions are affected to some degree when tar is heated at 125° C. in the presence of air. If the effects of air are considered, the aromatic and tar-acid fractions seem to be important in pitch formation.

Jan 1, 1956

By Graham W. Marks

In broadening the utility of spectrochemical methods 9f analysis of ore samples 3,4/ a procedure employ in the total energy method, has been adapted to determination of silver in ores. Silver is the first element in group I of the periodic table to be studied in the Bureau of Mines program. Two silver lines in the spectrum, Ag X\ 3280.683 and 3382.89lR were used in the study, and the problems that had to be overcome were: (1) Influence of extraneous elements on line intensities, (2) preparation of standard curves, and (3) improvement in equipment and technique to increase accuracy. Sodium, potassium, sulfur, selenium, iron, cobalt, and nickel yielded low intensities and hence low results, particularly on the samples high in silver, but addition of 60 percent or more of lime counteracted these effects. One calibration curve must be used for samples low in silver and other for those high in silver. The chocks with fire assaying were close enough for preliminary or exploratory investigations, and the method is much more rapid.

Jan 1, 1948

By Hal D. Peterson

In research sponsored by the Bureau of Mines, a technique was developed for simulation of heap leaching on uranium ores. The equipment used for this simulation consisted of 2-ft-diam columns, constructed in sections, such that ores as coarse as minus 4-in could be treated in bed depths ranging from 8 to 18 ft with test condition variations. The technique consisted of the separate steps of ore preparation, column loading, charge wetting, leaching, washing, and residue recovery. For the ores studied, sulfuric acid was found to be generally superior to alkaline lixiviants. The rate of uranium extraction by acid leaching proved" to be primarily a function of percolation rate, alkalinity of the ores and oxidant requirements of the ores. Column leaching was closely comparable to field-scale heap leaching in terms of uranium extraction rate and recovery results. Acid and oxidant requirements were lower for the field-scale operation. All column tests, as well as the field-scaly heap, achieved in excess of 96-pct uranium extraction on a Bear Creek, Wyoming ore.

Jan 1, 1985

By C. J. Walker, Ray V. Huff

The feasibility of inert - gas cushions in underground gas storages was studied by the Bureau of Mines in accordance with a continuing program of cooperative research between the natural gas industry -- through the American Gas Association . As mixing of the inert - gas cushion with the stored natural gas is undesirable , the various mechanisms tending to bring about such mixing were the subjects of both theoretical and experimental studies . These studies indicated the practicability of such cushions is dependent upon both reservoir and operating conditions . Equations and tables of illustrative data relating the various reservoir and operating conditions to the expected time required for undesired mixing to occur in ideal reservoirs are presented . This information permits estimating the relationship of such factors in actual storage operations .

Jan 1, 1964

By A. C. Fieldner

In the course of its investigations on the properties of coal and in rendering fuel-inspection service to other agencies of the Government, the Bureau of Mines has accumulated a comprehensive file of coal analyses that includes data on virtually every coal field of commercial importance in the United States. As knowledge of the composition of coal is potentially valuable to every user of coal, the Bureau publishes its analytical records. Before 1921 such publications contained analyses of coal from all parts of the United States; individual analyses or average analyses of a series of shipments of coal were given with the name and location of the mine producing the coal. Beginning in 1921 the analyses were published by separate States because the quantity of data had become so great. The separate papers published to date, with Bureau of Mines Technical Paper numbers, are as follows: Alabama, 347; Arkansas, 416; Colorado, 574; Illinois, 634 and 641; Indiana, 417; Iowa, 269; Kansas, 455; Kentucky, 30S; Maryland, 465; Missouri, 366; Montana, 529; New Mexico, 569; Ohio, 344; Oklahoma, 411 ; Pennsylvania (bituminous), 590; Tennessee, 356; Utah, 345; Virginia, 365; Washington, 491 and 618 (618, published in 1941, supplements 491); West Virginia, 405 and 626; and Wyoming, 484. From time to time the various papers will be revised to include later analyses and other data. The Bureau of Mines annually receives many inquiries as to the composition of coals obtained from specific localities or, conversely, as to the localities from which a given kind of coal may be obtained. This paper presents a summary, in tabular form, of the composition of commercial coal resources of the country. Specimen analyses are given exemplifying the analysis of coal mined in each coal-producing county, or, where it was feasible, coal from each bed in each county; also, ranges of analyses, within which the composition of most of the coal represented will fall, are given where there were enough analyses to permit satisfactory determination of the ranges. In addition, the degree of metamorphism from lignite toward anthracite of much of the coal is indicated by the classification by rank. This classification reveals to more experienced users of coal some of the general properties of coal, that is, whether the flame will be long or short, whether the coal will cake in the fire, and how it is likely to behave on exposure and in storage.

Jan 1, 1942

By Robert W. Smith

The Bureau of Mines is engaged in a systematic evaluation of the thermodynamic properties of combustion gases. These studies are designed to provide basic thermodynamic information of high accuracy, facilitating the theoretical study of flame and combustion phenomena. This report is the fourth of a series4/ presenting results of the study for particular fuel-oxidant systems. These calculations have as their objective the evaluation of the constant pressure flame temperatures of methane-air, propane-air, and ethylene-air mixtures for a range of pressures.

Jan 1, 1953