Search Documents

By H. J. Hager, B. W. Gandrud, G. D. Coe

"INTRODUCTION The reduction of washery losses of marketable coal is a phase of coal preparation important to many of the Alabama coal producers. The problem has wide scope, and this report deals with but one of its several aspects. The investigation on which this report is based was made by the Southern Experiment Station of the Bureau of Mines with the cooperation of the Alabama By-products Corporation and the University of Alabama. The Alabama Byproducts Corporation provided samples of table middlings from its Colta washery on the Mary Lee bed at Flat Creek, Ala.PRACTICE AT THE COLTA WASHYAt Colta run-of-mine coal is crushed in a hammer mill in closed circuit with 5/16-inch square-mesh vibrating screens and tabled without classification on eight rectangular-deck wet tables. The coal is more friable than the bone normally present, and hence the bone is concentrated in the coarser sizes. An unclassified feed of this character can not be tabled with high efficiency to low ash content because of the sizing action of a concentrating table, which is such that when the tables are adjusted to exclude the coarse bone from the washed coal, a large amount of fine coal is lost in the middlings. At the time this investigation was undertaken there was no market outlet for middlings, with the result that middling products had to be discarded with the refuse."

May 1, 1939

By Arnold P. Pipilen

In a study of the principal factors affecting the transport of coal-water mixtures through a centrifugal pump and a pipeline, the interrelation between solids concentration, velocity, and pressure drop was established for a bituminous lump coal (minus 2 inch) in concentrations up to 48 weight-percent. An optimum concentration was found to exist for maximum capacity of a given pipe-line, and for minimum energy requirements per ton of coal. Coal size degradation by particle fracture took place in the pump; abrasion and attrition to form fines took place in both pump and line. A novel system of studying flow of solid-liquid mixtures in pipelines by the determination of relative sound intensities was developed.

Jan 1, 1966

By Jr. Blake

This work was done to determine the technical feasibility of using the Pedersen process to produce cell-grade alumina and an iron byproduct from the high-silica and titania bauxites of the Pacific Northwest. Smelting of these bauxites with lime and coke at about 1,750° C in an electric arc furnace produced calcium aluminate slags in which at least 80 percent of the alumina was leachable by sodium carbonate solution. After a lime-desilication of the sodium aluminate leach liquors, neutralization of these solutions with carbon dioxide resulted in precipitation of an alumina hydrate of sufficient purity for calcination to cell-grade alumina. Recoveries of byproduct iron averaged over 90 percent; however, the iron contained about 1 percent phosphorous and would require additional refining. Additional small scale tests on these slags showed the following: (1) Titania had little effect on leachability if sufficient additional lime was added to form calcium titanate (CaO.TiO 2); (2) a slag containing about 14 percent silica required a slower cooling rate than one containing 7 percent silica for formation of high percentages of soluble aluminates; and (3) high-silica slags leached better at room temperature for long periods than at 65° C for shorter periods, but low-silica slags leached well by either method.

Jan 1, 1967

By K. L. Rubow

"IntroductionAir sampling for airborne contaminants requires a system for moving air, a collection method, and a procedure to determine the quantity of contaminant collected. Because occupational exposure limits and air quality standards frequently are expressed in terms of concentrations, a method of determining the volume of air sampled is also needed. The four principal components in a sampling train are shown in Figure 12-1. The inlet admits the air sample into the train; the collector(s) separates the gas, vapor, or particles from the air; the flowmeter measures the rate or total quantity of air sampled; and the pump (air mover) provides the suction required to draw an air sample through the train. Inlet sampling considerations are discussed in Chapter 21. Various types of collectors are described in subsequent chapters. Flowmeters are discussed in Chapter 7.This chapter will describe the air mover portion of the sampling train and air sampling systems that contain three or four components in a convenient package. The chapter consists of two parts. The first part contains a brief description of the different types of air movers and air sampling systems. The second part consists of tables and figures showing detailed information on a wide variety of commercially available air movers and sampling systems. ient size is filled with a liquid in which the suspected contaminant is insoluble. When the liquid is allowed to escape from the vessel, it is replaced by air from the atmosphere to be sampled. Such an air sample is an integrated sample rather than an instantaneous sample because the mass of fluid requires a finite time to empty. In fact, by employing a large vessel with controlled drainage, this method can be used to move air at low flow rates through a sample collector for extended intervals. Additional discussion of this method can be found in Chapter 17."

Dec 1, 1996

By Franklin B. W. Woodbury

The Bureau of Mines, as part of its goal of helping maintain an adequate supply of minerals to meet national economic and strategic A needs, is evaluating alternative technologies to treat oxidized taconites. Since process control is an essential element in the application of these process technologies, research was performed on a prototype monitoring system utilizing a Californium-252 (252-Cf) neutron source and a thermal neutron capture-gamma ray spectra analysis method to measure the amount of iron and percent solids in process slurries. The prototype system was used to monitor the concentrate and tailing streams in a 900-lb/hr flotation pilot plant during continuous around-the-clock tests. The iron content of the process slurries was determined by measuring the total peak areas under the capture spectrum peaks at 7.626-7.632 MeV, the associated escape peaks at 7.136-7.122 and 6.626-6.612 MeV, and the iron doublets at 4.900 and 4.998 MeV. A potential method for determining the percent solids in process slurries using the 2.22 MeV hydrogen capture peak is discussed. Results of this work demonstrate a potential method for providing process control parameters using the data from thermal neutron capture-gamma ray reactions.

Jan 1, 1980

By PAUL L. FISHER

This bibliography has been compiled by the Bureau in answer to many requests now being received for information on the briquetting coal and other carbons . In addition to publications issued by the Government in printed or mimeographed form, references are included to articles appearing in the technical press and in cooperative reports of work done jointly with states , colleges , and industries . References and patents are arranged in chronological order . Bureau of Mines bulletins , technical papers and Minerals Yearbooks are printed , and are obtainable from the Superintendent of Documents ,. Government Printing Office , Washington 25 , D. C. Reports of investigations , information circulars , and the directories and reports of the mineral industry surveys are published in mimeographed form and may be obtained without charge from the Publications Distribution Section , Bureau of Mines , 4800 Forbes Street , Pittsburgh 13 , Pa . Many Bureau of Mines publications , as well as bound copies of the foreign and American scientific and trade periodicals , may be consulted in technical , college , and large public libraries throughout the country. Dealers in new and second-hand books sometimes have copies of these reports for sale .

Jul 1, 1948

By Foster Fraas

Under a very high vacuum of 10-8 torr the transfer of terrestrial mineral beneficiation methods to the vacuum ambient of extraterrestrial locations such as the lunar surface was investigated. In the size range for the electro-static and magnetic separation of ores (minus 35 plus 150 mesh) there is no adhesion of particles produced by crushing and grinding due to the limited contact area, and for repeated contacts area size has a frequency of occurrence in accordance to the normal law. The photoelectric effect which is successful in separating a few minerals in an air ambient has a wider application in a vacuum, while the lack of air viscosity and sound transmission provides for high feed velocities and the adaptation of particle vibration to dispersion and grinding. Contact electrification is reversible upon return to atmosphere.

Jan 1, 1970

By H. A. Schrecengost

Information presented herein was gathered by examination of 29 fluidized- bed thermal coal dryers and by conferences with manufacturers and users of such equipment to determine what safety features could be incorporated in design, installation, and operation to minimize fire and explosion hazards. Fire and explosion hazards are inherent in certain types of coal dryers in that high temperatures are employed; the sizes and volatility of material handled are capable of propagating explosions; and drying gases are seldom, if ever, low enough in oxygen content to prevent ignitions of dust clouds, distilled gases, or their combinations. This is especially true for fluidized- bed dryers in which the coal is dried in air suspension and in which atmospheric air is constantly introduced to temper the heated furnace gases. Occurrence of fires on heated bedplates, in dust collectors, and in hot gas inlets was common in nearly all the dryers examined. Forceful explosions which produced external effects had occurred in 11 (39 percent), and internal "puffs" or "bumps" had occurred in at least 24 (79 percent) of the plants examined in the study.

Jan 1, 1965

By H. A. Schrecengost

Information presented herein was gathered by examination of 29 fluidized-bed thermal coal dryers and by conferences with manufacturers and users of such equipment to determine what safety features could b incorporated in design, installation, and op ration to minimize fire and explosion hazards. Fire and explosion hazards are inherent in certain types of coal dryers in that high temperatures are employed; the sizes and volatility of material handled are capable of propagating explosions; and drying gases are seldom, if ever, low enough in oxygen content to prevent ignitions of dust clouds, distilled gases, or their combinations. This is especially true for fluidized-bed dryers in which the coal is dried in air suspension and in which atmospheric air is constantly introduced to temper the heated furnace gases. Occurrence of fires on hated bedplates, in dust collectors, and in hot gas inlets was common in nearly all the dryers examined. Forceful explosions which produced external effects had occurred in 11 (39 percent), and internal "puffs" or ?bumps? had occurred in at least 24 (79 percent) of the plants examined in the study.

Jan 1, 1965

By A. S. Moore

The Bureau of Mines is doing research and development work on removing acid-gas impurities from synthesis gas made directly from coal. Since conventional gas scrubbers, packed towers and bubble-cap columns, are expensive to construct and difficult to operate with viscous solutions, one aspect of the work was developing a compact, agitated, gas-liquid contactor for use with concentrated absorbents. The efficacy of the agitated contactor for absorbing carbon dioxide in diethanolamine increased with increasing solution rate, turbine speed, diethanolamine concentration, and carbon dioxide concentration in feed gas, and with decreasing liquid-gas ratio. It was unaffected by pressure between 200 and 300 p.s.i.g. and little affected by temperature between 115 and 190° F.

Jan 1, 1961

By G. W. Birge, D. E. Wolfson, J. H. Lynch

Fourteen coal samples representing the Flag , Fire Clay , Whitesburg , Amburgy , Upper Elkhorn No. 3 , Upper Elkhorn No. 2 , Upper Elkhorn No. 1 , and Lower Elkhorn beds in Letcher County , Ky . , were carbonized by the Bureau of Mines - American Gas Association ( BM- AGA ) method , and yields of products and physical properties of cokes were determined . The samples tested were high- volatile A bituminous in rank , with dry , mineral - matter- free fixed - carbon contents ranging from 55.3 to 62.2 percent . Five of the samples , as received , were chemically unsuitable for metallurgical use because of excessive ash and/ or sulfur content . Generally , strength indexes of the cokes were low and all of the coals would require blending with higher rank coal to obtain satisfactory blast furnace fuel .

Jan 1, 1964

By J. L. Shultz

The Bureau of Mines extended its investigation of methanation catalysts. The noble metals (platinum, palladium, ruthenium, rhodium, osmium) and rhenium), molybdenum, and tungsten were tested in hydrogenations of carbon monoxide and carbon dioxide at 21 atmospheres in a temperature range between 200° and 600° C. From the 8 metals studied) 25 catalysts represent 5 catalyst types were prepared and tested. The impregnated 0.5-percent-ruthenium catalyst proved to be the most active and versatile of all the catalysts produced. Tungsten and the noble metals other than ruthenium were low in activity and usually required temperatures above 500° C for appreciable production of hydrocarbons. Molybdenum was moderate in activity, but further improvement in molybdenum catalysts seems possible.

Jan 1, 1967

By E. B. Kester

A study of the composition of the corresponding fractions of a primary and a high-temperature tar was undertaken to throw light on the net results of the pyrolysis of the primary products of coal decomposition in high-temperature coking practice, with reference both to total quantities of the chemically similar constituents and to their distribution throughout the boiling range. No exactly parallel investigations are on-record. The distribution of substances in high-temperature tars, however, is fairly well understood. Such tars are more or less similar, for they consist of the more stable phenols, aromatic and olefinic compounds resulting from the pyrolytic decomposition of a wide variety of primary tar constituents. For example, from a typical distillation curve for high-temperature tar phenols it may be seen that the greatest portion of the phenols distills between 180° and 220° C., a fairly narrow range. Low-temperature tars, on the other hand, are more complex, and hence exhibit dissimilarities from one to the next. Edwards, who has made a study of the acids, bases, and neutral oil of four low-temperature tar distillates, shows that the bases and neutral oil are evenly distributed among the fractions but that the concentration of the acids is greatest in the 200° to 230° fraction. Morgan and Soule find that in tar from the "Carbocoal" process, the 237° to 281° fraction has the highest acid content, whereas Davis and Parry find the 200° to 225° fraction of Freeport tar richest in phenols. Previous investigators have noted the following differences between primary and high-temperature tar: In the latter, naphthalene and anthracene occur in large quantities, the paraffins and naphthenes are negligible, the percentage of higher phenols is much lower than in primary tar, and the lower and more stable aromatic hydrocarbons have increased. In an endeavor to reconcile the change undergone when a primary is converted into a secondary tar, the writers have been unable to find references dealing with the extent of change which any one of the constituents of primary tar may undergo when subjected to secondary heating effects in the presence of other components, and the amount of the more stable compounds that may be expected from a given starting material.

Jan 1, 1932

By G. W. Jones

Explosion hazards that may exist when air becomes polluted with combustible gases and vapors are extremely dangerous, particularly if the volume of gaseous atmosphere is large, and an explosion under such circumstances could do tremendous damage to persons and property. The hazard is even greater if explosive mixtures are confined under high pressure, as the pressure could increase to tremendous proportions just before the container would rupture. Because of its interest in safety in the mining and allied industries, the Federal Bureau of Mines has investigated the flammability (explosibility) of various types of combustible atmospheres and published its findings. The explosibility of natural gas has been studied, and the limits of flammability have been determined and published. Other investigations have shown how explosions of natural gas-air mixtures may be prevented by the addition of nitrogen and carbon dioxide.

Jan 1, 1949

By L. B. Pankratz

The Bureau of Mines measured heat capacities of alpha and beta spodumene (LiAlSi2O5) and of beta eucryptite (LiAlSiO4) over the temperature range 51° to 298° K. The entropies at 298° K were found to be 30.9 ± 0.2 cal/deg mole for alpha spodumene, 36.9 ± 0.3 cal/deg mole for beta spodumene, and 24.8±0.2 cal/deg mole for beta eucryptite. High-temperature heat content measurements above 298° K were conducted for the same compounds. Measurements were made to 1,150° K for alpha spodumene, 1,600° K for beta spodumene, and 1,470° K for beta eucryptite. Tables of heats and free energies of formation are given from the elements and from the constituent oxides.

Jan 1, 1967

By Albert L. Toenges, Henry E. Dekay, James N. Scudder

Support of the immediate roof in coal mines is essential for their safe operation, and timbers are the most common means of support. Their effectiveness depends upon their resistance to decay. The theory has been advanced by some mine operators that rock dust, which is applied to ccal-mine workings to prevent propagation of explosions, accelerates the decay of mine timbers. As the results of part 1 of this study were inconclusive, the study was continued. Its principal objectives are: 1. To determine the effect of rock dusting upon decay of mine timber. 2. To compare the extent of decay of timbers in two mines in which underground conditions are similar. 3. To determine the loss in strength of the timbers after exposure to mine atmosphere. The studies were carried on in the Crucible mine of the Crucible Fuel Co. where the first part of this study was made, and in the Isabella mine of the Weirton Coal Co. The mines are on the Monongehela River and are adjacent.

May 1, 1943

By E. G. King

Strontium sulfide and barium sulfide occur as intermediates in commercial treatments of the impure natural sulfates to produce pure strontium and barium chemicals. Thermodynamic considerations involving these sulfides have been hampered by lack of basic data, such as the entropies at 298.15°K. This paper reports the results of heat capacity measurements of strontium sulfide and barium sulfide in the temperature range 50°-298°K. The entropies at 298.15°K. were derived from the heat capacity values. Free energies of formation at 298.15°k. were computed from the entropies and literature values of the heats of formation. Strontium sulfide and barium sulfide are thermo-dynamically less stable than calcium sulfide, but more stable than magnesium sulfide.

Jan 1, 1960

By R. L. Hopkins

Fifteen alkyl cycloalkyl sulfides and three dicycloalkyl sulfides were synthesized to provide reference compounds in the search for these classes of sulfur compounds in crude oils. In synthesizing sulfides by alkaline alkylation the order in which the reactants were added was shown to determine the yield and purity of the product.

Jan 1, 1966

By Walter Murphy

For a number of years the Bureau of Mines has been studying the properties of crude petroleums produced in the United States and the Western Hemisphere. A number of reports have been published giving the analyses of crudes from the different fields and regions as made by the Bureau of Mines Hempel method of analysis.4 Several of these reports include analyses of crude oils from the Rocky Mountain region.5/ The search for new fields and new producing horizons in old fields in the Rocky Mountain region has been quite intensive during the last few years, and a number of discoveries have been made.

Jan 1, 1937

By Walter Kawa

Coals of various rank were reacted by the Bureau of Nines in plasma jets generated from argon and argon-hydrogen mixtures containing up to 33 volume-percent hydrogen. Average plasma temperatures ranged from about 3,400° to 12,000° C. Products were a solid residue and a gas containing hydrogen, methane, acetylene, diacetylene, and oxides of carbon. The highest yield of acetylene obtained with argon plasmas was 15 percent by weight of moisture- and ash-free coal. The data indicated that acetylene yields of 40 percent or higher can be obtained from the reaction of coal in argon-hydrogen plasmas, although results from these experiments could not be correlated with operating variables because of low recoveries plasma contained sufficient energy to heat the coal to temperatures as high 9,000 or 10,000° C, but complete devolatilization did not occur in any experiment.

Jan 1, 1966