Search Documents

By Danny Hagood

The drilling of horizontal boreholes as a means of degasification in advance of mining has been tried at Jim Walter Resources, Inc., No. 4 Mine. In a joint venture with the U.S. Bureau of Mines, a series of horizontal drainage boreholes have been drilled in the panels of an advancing continuous miner section with impressive results. The combined methane gas production rate has ranged from 205,000 to 680,000 cfd (cubic feet per day} with individual "in-seam" horizontal holes producing up to 332,000 cfd. The methane liberation from the ribs for the entire panel length has decreased from an average of 8.75 cfm (cubic feet per minute) per 100 feet of entry to 4.05 cfm per 100 feet, a 54 per cent reduction. The actual gas concentration as measure at the surface discharge point normally ranges from 85 per cent to 95 per cent methane. As a consequence of the significant reduction in methane liberation rates from the panels of the section, a 50 per cent increase in productivity from the section has been realized.

Jan 1, 1983

By F. S. Crawford

During the course of a study of the safety organizations of the various iron mining companies in the Lake Superior district considerable in¬ formation regarding the methods of safety inspection in use was obtained which may be of value to other companies beginning safety work or contemplat¬ ing changes in their methods. A short description of the safety-inspection methods of eleven of these companies is given in this paper, and in the appendix are illustrated a number of forms used for safety inspections by several of the companies. Most of the companies whose methods are described use few forms for formal inspection. The one long form (10) attached which is used for a general in¬ spection by the safety inspector appears to present a good method for enabling the inspector to check all branches of his inspection and to assure himself that everything has been covered. All names of companies have been deleted from this paper and from the forms because the object is to disseminate information of constructive value rather than to point out the methods of particular companies by name.

Aug 1, 1931

Provide reasonably priced, reliable fire protection for front-end loaders. Approach Automatic fire sensing and suppression systems were developed and ruggedized for use on front-end loaders operating in harsh mine environments. How It Works Temperature sensors mounted in the loader's engine, transmission, and articulation areas detect the heat from a fire while it is still small and controllable. This triggers the release of the ABC class dry chemical extinguishing agent through a fixed piping system onto the fire. The system can also be manually activated from either the cab or ground level. Locations of the principal components of the system are shown in the drawing. Two control subsystems were designed to respond to varying fire protection needs and mine conditions. One subsystem only initiates discharge of the extinguishing agent. The other subsystem initiates visual and audible operator alarms if there is a fire sensed or if there is a fault in the control circuit.

Jan 1, 1979

By C. P. Bowie

The Bureau of Mines has been conducting investigations with the view of determining the types of containers best adapted to the stor- age of oil. These investigations have shown that tanks composed wholly of steel give the best results. Where larger containers than it is feasible to build with steel are desired, concrete-lined reservoirs can be recommended for some grades of oil. Practically all such containers in use at present have wooden roofs and this type of construction is here described, although it is the belief of the writer that concrete roofs would be far more satisfactory in every way, and that the difference in cost between a concrete and a wooden roof would, as a rule, in a few years' time, be offset by a saving of oil and in cost of repairs and renewals.

Jan 1, 1918

By George S. Koch

A mathematical simulation model has been devised to guide the layout of underground mine workings, drill stations, and drill holes that are established in order to search for tabular ore bodies. Developed and tested for elliptical ore shoots in fissure veins in the Galena mine, Coeur d'Alene district, Idaho, the model can also be applied to ore bodies contained within sedimentary beds (for instance, many types of uranium, copper, and gold ore bodies) or other tabular structures. Programed for a time-shared digital computer, the model contains both stochastic and deterministic variables. Stochastic or natural variables include the number of ore shoots and their sizes, orientations, locations, and values. Deterministic or controllable variables include (1) locations and costs of workings; (2) drill-station locations and costs; and (3) drill hole azimuths, inclinations, lengths, and deflections, if any. For various assumptions about the stochastic variables, the model is run while the controllable variables are changed deliberately. Thus, layouts are devised to determine the percentages of the total number of assumed ore shoots found at different costs. In order to choose among the various layouts, cost-effectiveness measures are calculated.

Jan 1, 1974

By T. G. Carnahan

The Bureau of Mines investigated a flotation-nitric acid leach procedure as part of the goal to maximize minerals and metals recovered from primary and secondary domestic resources. Studies were conducted on an ore that contained carbon-bearing and sulfide mineralization that rendered a portion of the ore refractory (resistant) to conventional leaching technology. The procedure investigated for treating the ore consisted of the following: (1) separation by flotation of the carbonaceous and sulfidic components from the ore, (2) leaching the flotation concentrate with nitric acid at 100° to 110° C, (3) leaching the flotation tailings with sulfuric acid, and (4) processing the combined leached slurries in a conventional manner to recover yellow cake. In step 2, HN03 is converted to gaseous products from which it is regenerated by reacting these products with air and water for further leaching. An overall uranium extraction of 96 pct was achieved by this procedure.

Jan 1, 1979

By Raymond B. Ladoo

SOAPSTONE

Feb 1, 1922

By C. W. Vierrether

Tailings from the Pea Ridge iron mine contain significant amounts of apatite, which has rare-earth element values associated with it. In association with the recovery of rare-earth minerals as a secondary resource, the U.S. Bureau of Mines conducted an investigation on the recover ability of the rare-earth minerals from these tailings. The mill tailings were subjected to a phosphate flotation to separate the apatite from other constituents. More than 70-pct recovery of the rare-earth values was achieved. Based on mineralogical characterization and prior analysis of rare-earth-bearing breccia pipe material at Pea Ridge, it is proposed that processing this phosphate concentrate on a vanner table would yield up to a 95-pct recovery of the rare earths in the concentrate, with the apatite reporting to the tailings. Intensive ore microscopy studies of the original tailings to the flotation products led to the identification of monazite, xenotime, and rare-earth-enriched apatite as the major rare-earth-bearing minerals in the tailings.

Jan 1, 2010

By V. A. Nieberlein

This paper presents the results of research undertaken to recover titanium and columbium by low-temperature chlorination of low-grade columbium-bearing ilmenite concentrates, and to simultaneously remove chlorinated impurities from the volatile chlorides without resort to distillation. Coke-reduced ilmenite was chlorinated at 400° to 500° C., and the resulting TiC14 was free of most impurities before condensation. A heated purification column was used wherein various packing materials reacted chemically or physically with the impurities which passed through them in the vapor phase. A nearly water-white TiC14 product was obtained directly. The principal impurities in the titanium tetrachloride were: 0.02 percent Fe, 0.01 percent V, 0.05 percent A1, 0.04 percent Si, and 0.07 percent Cb. This is a less pure product than commercial TiC14. Most of the columbium was recovered as crude CbC15, requiring further refining.

Jan 1, 1960

By Jon C. Volkwein

The Bureau of Mines, Foster-Miller Inc., and Beaver Creek Coal Co. have evaluated the ability of a new system to ventilate a 40-ft-deep cut. A remote-control continuous-mining machine, in a 7-ft-thick seam, with exhausting brattice was fitted with an improved sprayfan system plus additional forward and reverse pointing sprays. Static and dynamic tests using tracer gas were conducted in a full-scale model and under-ground to measure the effectiveness of exhaust face ventilation for various deep-cutting mine and spray configurations. When compared to a lO-ft primary ventilation brattice, the extended-cut spray system consistently provided better face ventilation at all configurations up to and including a 40-ft brattice setback. The system also provided good dust protection and visibility for the machine operator. Another safety advantage is the elimination of the need to set temporary roof supports to maintain the ventilation brattice.

Jan 1, 1985

By Robert A. Jankowski

"Following passage of the Coal Mine Health and Safety Act of 1969 (Public Law 911173), the Bureau of Mines initiated a research program aimed at controlling respirable dust exposures of coal mine workers. Respirable dust is the dust that gets into, and interacts with, the lungs of those who inhale it. It has long been recognized as a severe health hazard to mine workers. This program has been implemented by a team effort consisting of the Bureau's in-house capabilities, the Generic Center for Respirable Dust, and contractors, as necessary. Over the years, Bureau research has addressed principally three areas:o Compliance with the Federal 2.0 mg/m3 dust standard (1970-76).o Dust control for longwall mining (1976-1983).o More stringent respirable dust standards due to quartz dust (1983-1987).In addition, fundamental studies have been conducted by the Generic Center for Respirable Dust, with emphasis on penetration of dust into the lung. Accomplishments have been significant, but problems remain, as noted later.The Coal Mine Health and Safety Act of 1969, established a 2.0 mg/m3 dust standard for all coal mining operations, underground as well as surface. At the time of enactment of this legislation, the industry was averaging approximately 4.0 mg/m3. The Bureau of Mines respirable dust research program played a significant role in identifying and developing effective technology to allow better compliance with this new standard, thanks to industry implementation and Federal enforcement."

Nov 1, 1988

By Foster Fraas

The Bureau of Mines investigated a method for calculating values of adsorption energy; the goal was to devise an equation consistent with experimental data accumulated in the investigation of adsorption as related to ore separation processes. Numerical identification of the constants of a previously formulated equation provided an equation by which values of adsorption energy could be calculated. Values thus calculated checked with those obtained by calorimetric measurement.

Jan 1, 1965

By R. F. Stewart

A nuclear meter based on measurement of prompt capture gamma rays is being developed for monitoring the sulfur content of coal streams. Equipment has been built to measure sulfur rapidly, and methods have been devised to compensate for changes in moisture, ash, and bulk density of coal flowing through a bin. Pilot plant tests of the system with various additives to different coals show a precision and accuracy of 0.02 percent sulfur and 0.04 percent sulfur, respectively. Based on these results, a hardwired meter has been fabricated for testing in a commercial coal preparation plant.

Jan 1, 1974

By R. A. Cortese

The U.S. Bureau of Mines has developed a flame-radiation-powered trigger device to explosively activate suppression barriers to quench gas and coal dust explosions. The major component of the device is a silicon solar panel, which converts radiation from the developing explosion into electrical energy to initiate an electric detonator, which releases an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 W of electrical power when exposed to the sunlight are producing about 200 W when exposed to a full-scale dust explosion. The solar panel is electrically isolated from the detonator by a pressure-sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame-powered photogenerator prevents false barrier activation and requires no external power supply.

Jan 1, 2010

By A. F. Colombo, D. W. Frommer

Bench- scale tests were made to determine the applicability of flotation as a means of upgrading finished and semifinished magnetic concentrates prepared from reductively roasted iron ores . Both anionic and cationic flotation methods were used to remove siliceous gangue from the magnetic concentrates and produce upgraded products . Seven magnetic concentrates , containing from 6.7 to 13.7 percent SiO2 , were improved by the flotation treatment , yielding final concentrates containing less than 6.0 percent Si02 . Cationic flotation methods were studied on four of the seven samples ; of this group only one sample yielded better results by cationic flotation than by the anionic method .

Jan 1, 1964

By D. E. Hirsch

The Bureau of Mines has developed a systematic procedure for separation, characterization, and semiquantitative analysis of high-boiling (350° to 550° C) distillates of crude oils. Isothermal and molecular distillation were used to prepare the 370° to 530° C distillate of Recluse, Wyo., crude oil. The distillate was separated into fractions by chemical treatment, silica-alumina gel adsorption, and gel permeation chromatography (GPC). The fractions were analyzed by use of GPC correlations and mass and nuclear magnetic resonance (NMR) spectrometry. The increased knowledge of petroleum composition obtained from the data will contribute to improved petroleum processing and utilization and energy conservation.

Jan 1, 1974

By Kenneth H. Johnston

This report describes an in situ combustion project and three waterflood projects in Allen, Anderson, and Wilson Counties, Kansas, that will be visited during the 1964 annual tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the movement of heavy crude oil through the reservoir and into the wellbore with energy furnished by burning a portion of the crude oil therein. Another feature is the simultaneous injection of C02 and water, through separate tubing into input wells during early development, to increase injectivity at moderate pressures, Discussion of individual projects includes information on their early history, source and treatment of injection fluids, oil production-decline curves, and the results of water injection on oil production.

Jan 1, 1964

By Dean C. Holt

This work was done to appraise the potential of titanium minerals in known titanium- bearing placer deposits and potential titanium- bearing placer areas in western Montana . Reconnaissance studies were made of more than 225 stream areas . Churn drilling and other placer exploration techniques were used in sampling eight deposits . The sampling results indicate that areas containing more than 10 pounds of ilmenite and other titanium- bearing black - sand minerals per cubic yard occur in the Bitterroot , Upper Clark Fork , and Jefferson River drainages . The chief source for the constituents of the black sands appears to be the Idaho batholith , and the highest black - sand concentrations are generally found near the source . Sample testing methods include gravity and magnetic separation and visual microscopic as well as chemical and radiometric analyses on deposits sampled in detail .

Jan 1, 1964

By I. D. Shah

The copper-nickel ore of the Duluth Gabbro Complex in northeastern Minnesota is a large potential domestic resource of cobalt and platinum-group metals. However, because of the low grade of the primary metal values (0.5 pct Cu, 0.15 pct Ni), the private sector has assigned a relatively low priority to the development of technology for processing this ore, anticipating that mining probably would not begin until the mid-1990's. Furthermore, preliminary processing flowsheets considered by the mining companies centered on the primary metal values. As part of an effort to help provide the basis for technology to recover critical and strategic minerals from domestic resources the Bureau of Mines is investigating methods to recover all of the mineral values, in the Duluth Gabbro material, with particular attention to the byproduct critical minerals. A key step in this process is the removal of a relatively large amount of iron present in the bulk sulfide flotation concentrate to permit subsequent extraction of mineral values. This report describes a direct smelting method that removes most of the iron and produces a copper-nickel-cobalt matte, an intermediate product from which the metal values subsequently are separated. Copper, nickel, and cobalt grade and recovery data are presented for the direct smelting method. Test results showed that under certain conditions some of the mineral values reported to the slag, requiring slag cleaning to recover them.

Jan 1, 1983

By Stanton L. Tainter

"As an adjunct to its minerals-investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the supervision of J. H. Hedges, chief, Tucson Branch Mining Division, and under the general supervision of Lowell B. Moon, chief, Mining Division, reports upon certain methods devised to overcome difficulties encountered in cementing of diamond-drill holes at a Bureau of Mines project at Christmas, Gila County, Ariz.Pressure grouting was employed to recondition a caved hole it was desired to reopen and deepen. The hole, which had boon stopped 7 months previously at a depth of 488 feet, was caved below 449 feet in a contact zone of claylike, altered diorite and crumbly metamorphosed limestone. As other means of obtaining moderate pressure were not available, carbon dioxide gas, drawn from tank of liquid carbon dioxide through a pressure reducing and regulating valve, was used. The hole was reopened successfully with 12 grouting jobs.Another hole, where cawing from several water-bearing fractures between 202 and 232 feet gave trouble, was successfully cemented by the use of a grouting plug. An attempt to cement through the rods had failed, owing probably to agitation caused by water currents. Pressure grouting through the caning set above the cave could not be need, because water was forced up outside the casing when pressure was applied. The problem was solved by using a wooden plug 1-13/16 inches in diameter, which, when soaked in water, expanded to a tight fit in an AX hole. A hole was drilled through the plug, and a rubber flap valve was nailed to the lower end. In the upper end of the plug the hole was enlarged to fit loosely over an EX rod coupling finished smooth. The plug was lowered on the end of the drill rods to a point about 10 feet above the cave, where it was allowed to expand tightly to the hole. Cement grout was then pumped through the rods, and the rods were removed from the hole. After allowing time for the cement to set, the wooden plug was chopped out and drilling van resumed.Over 300 tests were made to determine the type of cement most suitable for use on the Christmas job, and the effect of cement-water ratio, temperature, and various admixtures on workability, setting time, and strength. The results of these tests, described in detail in the body of this report, indicate the desirability of thoroughly testing available cements when it is necessary to drill holes under difficult conditions that may cause failure.When it became desirable to reopen and deepen a caved drill hole, it was considered easiest to recondition the hole by pressure grouting, As other mans for obtaining moderate pressure were not available, a method utilizing carbon dioxide gas was employed. The hole was reconditioned successfully with 12 grouting jobs."

Nov 1, 1949