Search Documents

By F. P. Haver

The purpose of this investigation was to determine the effect of common impurities, that is, oxygen, nitrogen, carbon, and iron, on the Brinell hardness of electrolytic titanium. On a weight basis, nitrogen had the greatest hardening effect, followed by oxygen, carbon, and iron in order. The hardening effects of oxygen and carbon were almost identical up to a concentration of approximately 0.1 percent by weight. Above this concentration, the relative hardening effect of carbon decreased rapidly, possibly because of its limited solid solubility in a-titanium. Hardness vs. composition curves for both oxygen and nitrogen were essentially straight lines over the range of Brinell hardness numbers (B.h.n.) covered in the investigation. The hardness of titanium was also determined as a function of the percentage of impurity atoms. On this basis, iron in concentrations up to 0.17 atomic percent had a greater hardening effect than either oxygen or carbon. INTRODUCTION Determination of the as-cast hardness of arc-melted titanium is a method of quality control widely used in industry. Numerous studies4/ have been made of the effect of impurities on the hardness obtained by this method. However, most of them have been based on the use of either iodide titanium or commercially pure Kroll sponge (B.h.n. >90), as a starting material.

Jan 1, 1959

Determine the effectiveness of remining operations in reducing contaminant load (acidity, iron, and sulfate) of discharges emanating from abandoned surface and underground coal mines. Background Until the implementation of remining initiatives, most States had regulations that held the operator remining an abandoned site responsible for preexisting acid mine drainage (AMD) discharges. For example, if a mining. company wanted to remine an area hydrologically connected to an existing AMD discharge, the company became responsible, as soon as the site was activated, for treating that discharge to meet effluent standards. If the mining operation improved the quality of the discharge, but the discharge failed to meet effluent standards, the company was held accountable for perpetual treatment. Because of this regulation, most mine operators avoided abandoned sites with minable coal reserves and AMD discharges. However, changes in remining legislation allow coal companies to be released from treatment liability as long as the post-remining pollution load does not exceed the pre-remining level. If remining can improve water quality through improved mining and abatement techniques, abandoned mine land (AML) areas that previously were liabilities could become

Jan 1, 1994

By A. J. Barry

Five makes of expansion-type shells and two types of bolts (mild-steel and high-strength) were used in 30 tests made in sandstone and shale roof, The results show that the anchorage obtained in both the sandstone and shale were stronger than either type of bolt. That is, the yield loads of both bolt types were exceeded before excessive anchor slip occurred. A relationship for evaluating the anchorage effectiveness of 3/8-inch-diameter, expansion-type bolts is presented. A comparison of test results indicates that the anchorage effectiveness of 5/8-inch- and 3/4-inch-diameter expansion-type bolts did not differ appreciably.

Jan 1, 1957

By Donald S. Colby

This Bureau of Mines report is essentially a handbook, or manual, for making the type of mineral resource valuation commonly required for such public policy problems as mineral leasing. The principle of resource valuation through the capitalization of cash flow is well established. A mathematical procedure, based on a simplified accounting system, is detailed for calculating cash flow from revenue, plant costs, and operating expense. Variations of procedure cover cost depletion, percentage depletion, and depletion limited to 50 percent of net income. The influence of the depletion provisions of the tax regulations on the value of a resource to an owner and to an operator is analyzed. The relationship of royalty, bonus payments, and sales price to resource value is also described, and methods for approximating resource values using these payments as input data are developed.

Jan 1, 1969

By N. L. Wimmler

"INTRODUCTION The Southern Cross district in Deer Lodge County, Mont., has been chiefly a gold producer. Most of the production has come from gold-bearing hematite-limonite ores. Some of these ores were mined and shipped to smelters for use as flux in smelting copper ores. A magnetite deposit in the Pomeroy property, containing no gold or other economic nonferrous minerals, was mined from 1921 to 1923, the ore being shipped to smelters for flux.The iron-bearing deposits in the Southern Cross area were examined by Bureau of Nines engineers/ on June 28, 1943, and October 14, 1943. As a result, a Bureau exploration project was recommended; it was conducted during 1944. A magnetometer survey was first made of the magnetite-bearing area at and in the vicinity of the Pomeroy property. Exploration by diamond core drilling was then conducted within this area, and in the Southern Cross and Hold Fast properties. The cyanide tailings dump at the Hold Fast mill was sampled by auger drilling.This report presents the data obtained by the Bureau of Mines exploration."

Dec 1, 1946

By S. H. Lorain

The Minah silver-lead mine in the Wickes district, Jefferson County, Mont., produced substantial quantities of silver-lead ores in the 1890's. The mine has been abandoned since the "silver panic" of the early 1900's. As a part of the Bureau of Mines: program to develop new sources of lead to overcome the growing shortages of that metal, a development project was started at the Minh mine in April 1946 and continued until June 1947, during which 5,600 feet of angledozer trenching and. 1,093 feet of core drilling were completed on the main vein and nearby parallel veins: As a result of this work, interest in the property was stimulated and private operators are now engaged in reopening the mine. This report discusses the past history, geologic setting, and the recent and early operations of the mine.

Jan 1, 1948

By James W. Myers

The Bureau of Mines studied factors affecting ignition of coal mine refuse and on methods for control of burning. Laboratory experiments showed that air permeates more readily through segregated than through nonsegregated refuse and that air permeability is greater through coarse than through fine particle refuse. Minus 3-1/4-inch refuse ignites spontaneously more readily than minus 1/4-inch refuse. The burning of a 1,000-pound conical coal pile was con-trolled by capping with an 18-inch-thick layer of minus 1/4-inch refuse containing 37 percent combustible. In field trials, the burning of refuse at operating mines was controlled by capping with a layer of fine refuse. Water, applied as a spray or by injection, quenched surface flames and cooled the burning waste. Inspection of refuse piles at operating mines showed that the spontaneous ignition tendency is affected by the exposed surface relative to the total volume and the segregation of particles during dumping.

Jan 1, 1966

By E. G. Noble

The effects of hydrogen chloride (HCI) concentration and temperature on the solubility and hydration state of the alkali chlorides LiCI, NaCI, and KCI and the alkaline-earth chlorides, MgCI2, and CaCl2 were investigated by the Bureau of Mines. Saturated aqueous solutions of the chlorides were sparged with HCI gas at temperatures of 20°, 40°, and 60° C. Increased HCI concentration caused decreased salt solubility be-cause of the common ion effect. Aqueous solubilities for the chlorides of Ca, Li, Mg, K, and Na ranged from 42.6, 45.2, 35.2, 25.5, and 26.1 pct, respectively, at 20° C to 56.9, 49.4, 37.6, 31.0, and 27.0 pct, re-spectively, at 60° C. In solutions sparged to HCI saturation, solubili-ties for these chlorides ranged from 22.4, 26.5, 3.0, 1.3, and 0.05 pct, respectively, at 20° C to 53.2, 48.8, 28.3, 2.6, and 0.8 pct, respec-tively, at 60° C. The solubilities of LiCI and CaCl2 in HCI solution were high because HCI solubility is low in these solutions. The chlo-ride salts of Ca, Li, and Mg formed hydrates, which depended on tempera-ture and HCI concentration. Monohydrates for LiCI, tetrahydrates and hexahydrates for MgCI2, and dihydrates, tetrahydrates, and hexahydrates for CaCl2 were obtained.

Jan 1, 1985

By Doris M. Hyde

Mineral industry activity in many of the smaller Caribbean Island countries has remained minimal. For this reason, specific references to Bermuda, Guadeloupe, Martinique, and the Netherlands Antilles have been removed from textual and trade table presentations. Any significant future developments will be reported as they occur. Readers are referred to earlier Minerals Yearbook editions for previous information. Table 1 production statistics have been modified in some instances. References to certain nonmetal commodities were eliminated because information has often been unreliable. Their inclusion in table 1 was not considered important to either an overview of the area or to compatibility with volume I of the Minerals Yearbook.

Jan 1, 1984

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946

By John J. Sammarco

The functional safety of programmable electronic (PE) mining systems is an international issue and concern. From 1995 to 2001, 11 PE-related mining incidents in the U.S. were reported by the Mine Safety and Health Administration (MSHA); 71 PE-related mining incidents were reported in Australia. MSHA does not have regulations for formal evaluations of the functional safety of PE mining systems. Hence, the National Institute for Occupational Safety and Health (NIOSH), in partnership with MSHA and the industry, generated the NIOSH safety framework for functional safety of PE mining systems. An overview of the NIOSH framework is given; the key framework elements, the safety life cycle and safety integrity levels are detailed. The safety framework approach has impacted the national and Australian mining industries by enabling the industries to advance from an ad-hoc approach to a formalized and systematic functional safety process. In retrospect, valuable lessons were learned for addressing functional safety and for changing industry perspectives and practices. These lessons continue to benefit mining and are applicable to other industries as well.

By L. C. IlsLey, H. H. Clark

As part of its investigations of the causes of mine accidents and of the safest and most efficient methods of handling electricity underground, the Bureau of Mines undertook a study of the ignition of mine gases by the filaments of electric incandescent lamps. This bulletin describes the investigation in detail and gives a complete record of the results obtained.

Jan 1, 1913

By M. J. Ferrante

Relative enthalpies of high-purity disodium hexatitanate (Na2Ti6013) were measured at the Bureau of Mines to provide new thermodynamic data needed to advance the technology of materials. Measurements from 298.15 to 1,478 K were made by drop calorimetry with a copper block. Tabulated values are listed for the standard relative enthalpy, heat capacity, en-tropy, and Gibbs energy function between 298.15 and 1,500 K. Enthalpy data are also given in equation form and are combined with thermodynamic data from the literature to derive values of standard enthalpies of formation, Gibbs energies of formation, and logarithms of the equilibrium constants of formation. Similar calculations were made for the reaction of Na20 with Ti02.

Jan 1, 1986

By Tell Ertl, Ernest E. Burgh, John R. Wagner

The principal goal of the Oil-Shale Mining Division is to develop the most economical methods and practices for mining oil shale. Experimental work in the mine has not progressed far enough to conduct full-scale breaking tests; therefore, mining season - to October 31, 1945, has been confined largely to problems connected with drilling cost oil shale. Calculations have indicated that commercial production will result in breaking the oil shale; the largest individual turn will be for drilling. This paper is a report on the progress of phase two of drilling research to date; it outlines the development of a successful hard-surfaced rock bit for drilling oil shale.

Dec 1, 1948

By Sidney Katell

Continuing the series of cost bibliographies which was initiated with the publication of Information Circular 7516 in October 1949, the present report covers the period from January 1959 through December 1959. The abstracted articles, concerned with all facets of cost engineering in the field of petroleum and chemical plants and related facilities, were obtained from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Report of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Week. 6. Coal Age. 7. Coal Utilization. 8. Cost Engineering. 9. Industrial and Engineering Chemistry. 10. Nucleonics. 11. Oil and Gas Journal. 12. Petroleum Engineering. 13. Petroleum Refiner. 14. World Oil. On Oct. 16, 1959 a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers became effective. This agreement provides for the publication of the annual bibliography under the sponsorship of both groups with the work load involved in the preparation divided equally between the two. As a result, the present report partially reflects the efforts of the members of the Association.

Jan 1, 1960

By E. A. Hewitt

This paper describing the mining practices at the Park Utah mine in the Park City district is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Park Utah mine is situated at Keetly, Utah, about 5 miles east of Park City. The Park City district lies on the eastern slope of the Wasatch Mountains, 25 miles southeast of Salt Lake City. The district embraces a tract located between the crest of the main range on the west and the mountain meadows along the eastern foothills. The elevation of the Union Pacific Railroad station at Park City is 7,000 feet above sea level. The town and mines are served by two railroads; one 28 miles long is a branch of the Union Pacific Railroad and connects with the main line at Echo Junction, east of Ogden; the other is 35 miles long and joins the Denver & Rio Grande Western Railroad at Salt Lake City. The district and mines are also accessible by excellent automobile roads from Salt Lake City and surrounding points (fig. 1).

Jan 1, 1930

By R. L. Loofbourow

The adjacent towns of Rouyn and Noranda, centers of the Rouyn mining district of western Quebec, are 360 miles by air line almost duo north of Toronto. Rouyn is reached from the main lines of the Canadian National Railways and the Canadian Pacific Railway at North Bay, Ontario, by the Temiskaming & Northern Ontario Railway and its subsidiary, the Nipissing Central Railway. Noranda is the southwestern terminus of a branch from the Canadian National Railway between Winnipeg and Quebec. The Rouyn mining district is a part of a mineralized zone that has been traced for a distance of 140 miles from Kirkland Lake in Ontario eastward into the Province of Quebec to the Pascalis district. From Rouyn the mine is 5 miler almost duo south over a gravel rend built by the company with assistance from the Province of Quebec.

Jan 1, 1933

By Hsin Wei Wu

A real-time Diesel Particulate Matter (DPM) monitor has been developed on the basis of the successful National Institute of Occupational Health and Safety (NIOSH) designed Personal Dust Monitor (PDM) unit. The objectives of a recently completed Australian Coal Association Research Program (ACARP) study were to modify the PDM to measure the submicrometre fraction of the aerosol in a real-time monitoring underground instrument. Mine testing focused on use of the monitor in engineering evaluations to determine how conditions can be improved. Studies, including a selection during Longwall (LW) moves as described in this paper, demonstrated how DPM concentrations from vehicles fluctuate under varying ventilation and operational conditions. Correlation between the current SKC DPM measurement system and real-time DPM monitors were conducted and results from six mines show a correlation between elemental carbon (EC) and the new monitor DPM mass ranging from .51 to .81 with R2 >.90. These differences are suspected to be due to variations from mine to mine in aspects such as mine atmospheric contamination, vehicle fleet variations, fuel type, engine maintenance, engine combustion efficiency, engine behaviour or interference from other submicrometre aerosol. Real-time monitoring readily reflects the movement of individual diesel vehicles and allows pin-pointing of high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. DPM monitoring approaches that have been available for some time based on shift average monitoring do not readily allow successful engineering evaluation exercises to determine acceptability of pollution levels. Identification of high DPM concentration zones allows efficient modification of mine ventilation, operator positioning and other work practices t o reduce miners? exposures without waiting for laboratory analysis results.

Jan 1, 2010

By Gloria L. Walker

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1990

By Wilbert T. Malenka

In its search for a highly productive mining system for anthracite beds pitching from 100 to 200, where conventional mobile equipment cannot be used) the Bureau initiated a longwall project by introducing a shearer drum cutter loader of European origin. Because of the undulating nature of the roof and floor and changing bed thicknesses, the machine proved inflexible and extra work was required in lifting bottom coal and blasting top coal.

Jan 1, 1966