Search Documents

By Fred N. Kissell, Andrew B. Cecala

In This Chapter [Where methane is emitted at longwall faces Where methane accumulates at longwall faces Using the modified shearer-clearer to eliminate ventilation eddy zones Using a walkway curtain to reduce methane buildup during the headgate cutout Control of frictional ignitions and The best location for the methane monitor] The methane released along a longwall face represents only 10%–20% of the total methane emitted from the entire longwall panel. Nevertheless, in very gassy coal seams, this methane released at the face can pose a problem because the shearer is a ready ignition source. Preventing methane ignitions at longwall faces requires four actions. The first is to provide better ventilation around the shearer to eliminate the ventilation eddy zones at the drums where methane builds up. These eddy zones are eliminated by mounting additional water sprays on the shearer to direct air into them. The second action to prevent methane ignitions is to install a water spray behind each cutter bit and regularly replace worn bits. Water sprays behind each cutter bit act to quench the hot metal streak that follows a worn bit when it strikes rock. The third is to ensure that no ventilation eddy zones are inadvertently created by poor placement of water sprays. The fourth is to ensure that the methane monitor on the shearer is in the best location to detect methane accumulations. ADDRESSING METHANE ACCUMULATIONS AT LONGWALL FACES3 Cecala et al. [1985a, 1989] and Denk and Wirth [1991] studied methane emission and ventilation patterns at longwall faces to find where methane accumulations are most likely. Although not always the case, the major source of methane at longwall faces is usually the breakage of coal by the shearer. Stress-related fracturing of the coal seam at the face, called bumps or bounces, can cause the release of additional gas (Figure 4–1).

Jan 6, 2006

By Michael A. Trevits

Since the promulgation of the MINER Act and the follow-up changes to the regulations governing mine seal construction and maintenance, mine operators must be acutely aware of the atmosphere in sealed mine areas and prepared to deploy control technologies when the conditions are warranted. On Site Gas Systems1 in Newington, Connecticut was awarded a contract by the National Institute for Occupational Safety and Health (NIOSH) to construct a novel in-mine nitrogen (N2) generation plant using pressure swing adsorption (PSA) technology. PSA technology utilizes carbon molecular sieve material and pressure to adsorb oxygen (O2) molecules while allowing N2 molecules to pass through the sieve material. The prototype PSA unit was tested at the NIOSH Safety Research Coal Mine (SRCM) where a 62,000 ft3 area of the mine was rendered inert during a series of two tests. The resultant data were then used to construct a CFD simulation of both injection tests. In addition, O2 depletion and gas leakage rates were quantified in the model and were compared to actual values. Once the model was calibrated, the sealed mine area was doubled and simulations were made with various injection rates and injection site locations to determine the impact on the time needed to render this area inert. This paper presents an overview of the PSA plant, the details of the gas injection tests and CFD modeling work.

Jan 1, 2010

By Kray Luxbacher, Mario Karfakis, Erik Westman, Peter Swanson

Three-dimensional velocity tomograms were generated to image the stress redistribution around an underground coal longwall panel to produce a better understanding of the mechanisms that lead to ground failure, especially rockbursts. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Eighteen tomograms were generated and high-velocity regions correlated with high abutment stresses predicted by numerical modeling. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated, indicating that velocity tomography may be an appropriate technology for monitoring stress redistribution in underground mines.

By P. L. Swanson, F. M. Boler

The U.S. Bureau of Mimes conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic destressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 21/2-week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 1993

By Thomas P. Mucho, Thomas M. Barczak, Dennis R. Dolinar

Maintaining ground stability in the gate roads, particularly the tailgate, has always been critical to the success of longwall mining, both in terms of safety and productivity. Several new support technologies have been developed in recent years to replace conventional wood and concrete cribbing for secondary roof support. Since their performance characteristics are unique, the best practices that have been developed with conventional wood cribbing may not be applicable for these alternative support technologies. Therefore, with so many options to consider and the importance of achieving adequate ground control at minimal cost, the trial-and-error approach to longwall gate road support is no longer prudent. This paper discusses a design methodology for standing secondary tailgate supports. This design technique requires in-mine measurements of tailgate support loading and convergence to establish a tailgate ground reaction behavior based on support and strata interaction. The methodology uses the performance characteristics generated in the National Institute of Occupational Safety and Health's (NIOSH) Mine Roof Simulator (MRS) to match the stiffness and load characteristics of various supports to the measured ground reaction behavior. It can be used to determine the appropriate application of alternative roof support systems or to design in-mine trials so that a fair and equitable comparison of different support systems can be made. A case study of the methodology at a western Pennsylvania mine site is presented in the paper, including a comparison of four alternative support technologies to the conventional wood and concrete cribbing historically used at this particular mine.

Jan 10, 2000

By R. E. Heithecker

In Kansas, almost every oil well drilled into a limestone formation is treated with hydrochloric (muriatic) acid upon completion. This is done to increase the potential capacity of the well and thereby increase its "daily allowable" production (see p. 9 ), to shorten the time required to produce the recoverable oil, and to increase the quantity of oil recovered ultimately from the reservoir. The porosity and. permeability of limestone formations seldom are uniform throughout the proved area, consequently the production capacities of completed wells vary considerably. Acid treatment of wells tends to increase production capacity and to equalize potential capacity. If offset wells already have been treated with acid, new wells usually are treated to protect the property on which they are drilled against drainage. Even though competitive conditions do not exist in a field, it

Jan 1, 1939

By R. E. Heithecker

In Kansas, almost every oil well drilled into a limestone formation is treated with hydrochloric (muriatic) acid upon completion. This is done to increase the potential capacity of the well and thereby increase its "daily allowable" production (see p. 9), to shorten the time required to produce the recoverable oil, and to increase the quantity of oil recovered ultimately from the reservoir. The porosity and. permeability of limestone formations seldom are uniform throughout the proved area, consequently the production capacities of completed wells vary considerably. Acid treatment of wells tends to increase production capacity and to equalize potential capacity. If offset wells already have been treated with acid, new wells usually are treated to protect the property on which they are drilled against drainage. Even though competitive conditions do not exist in a field, it

Jan 1, 1939

By S. J. Schatzel, W. P. Diamond, F. Garcia

Methane explosions have historically been one of the major causes of fatalities and injuries in underground coal mining operations. Advanced numerical models and predictive modeling approaches have the potential to offer optimized methane control solutions for general mine planning purposes and to address specific methane-related operational problems. This paper describes the development of reservoir models for the longwall mining environment and their application for investigating the influence of various completion design parameters on the methane drainage effectiveness of gob gas ventholes. The influence of increasing longwall panel width on the effectiveness of current gob gas venthole completion and placement strategies in the Pittsburgh Coalbed were evaluated and optimized designs developed to capture the expected increase in methane emissions on the larger panel.

By L. C. Brichta

During a study of the Badger-Peacock area from October 1950 to June 1953, the Federal Geological Survey and the Federal Bureau of Mines completed nearly 98 miles of resistivity profiling and drilled 96 test holes aggregating 17,628 feet of bore, In addition, seismic profile measurements were made along 8 traverse lines for an aggregate length of about 16,600 feet. The geophysical surveys were conducted by the Geophysics Branch of the Geological Survey; the drilling was done by the Bureau of Mines. Electrical-resistivity measurements disclosed 21 low-resistivity anomalies and 1 high-resistivity anomaly. Correlation of the resistivity data with the geological information revealed by the drilling disclosed that the low-resistivity anomalies indicated either slumped shale deposits in limestone sinks or undisturbed deposits of shale lying in erosional depressions in the limestone. The high-resistivity anomaly indicated hard, undisturbed limestone at or near the surface.

Jan 1, 1958

By R. Karl Zipf, Francois E. Heuze

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINETAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress-strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory-scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle () for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

On June 20, 1972, Ocean Energy was awarded Contract No. H0220055, entitled Portable Task Luminaire System Development. Initially, this was a 12 month program consisting of three phases: Phase I -- Design of the Luminaire System and Battery Chargers, Phase II -- Fabrication of Prototype Units, Phase III -- Fabrication of Production Prototype Units and Battery Chargers. In addition to developing the Portable Task Luminaire System, however, this contract was amended a number of times in the course of the program to include the development of a Low Coal Portable Task Luminaire, a Rib Mounted Luminaire System, and a Machine Mounted Luminaire System, all based upon the same high frequency fluorescent lighting and safety technologies involved in the Portable Task Luminaire. This report covers the activities of this program as amended, and includes the development and fabrication of all of the systems. This report constitutes the final fulfillment of the contract.

Jan 1, 1974

By M. P. Board, J. K. Whyatt, T. J. Williams

The U.S. Bureau of Mines has been conducting a series of rock mechanics investigations at the Lucky Friday Mime in the Coeur d'Alene Mining District of northern Idaho. In the present study, the energy release rate (ERR) index was used to evaluate three underhand stope backfill parameters--cement content, density, and placement gap-to determine their influence on rock bursts. This index provides a relative measure of the likelihood of rock bursting for a given rock mass. It is known that the elastic idealization of the rock mass inherent in this method causes underestimation of stope closure and hence underestimation of the influence of backfill on rock bursting. However, this evaluation still showed that (1) changing from present practice to one in which backfill was omitted altogether would increase the ERR by 42 pct and (2) perfect placement of backfill would reduce the ERR below present practice levels by 28 pct. The easiest step toward perfect placement would be elimination of the placement gap, which accounted for half of the difference in ERR between present practice and ideal placement conditions. There was no indication that increasing initial fill strength through increased cement content would affect the ERR.

Jan 1, 1992

By Paul M. Tyler

The technology of clay and the manufacture of ceramic products therefrom, and also the clay resources of most of the individual States, are already covered by a voluminous literature. The present resume touches these matters only briefly; its purpose is essentially to bring together in small compass certain of the elementary factors affecting the potential commercial value of a clay deposit. In its preparation the author made extensive use of the annual chapters on Clay in Mineral Resources of the United States and in the two annual issues of the Minerals. Yearbook that succeeded them. For careful review and constructive criticism of the manuscript, the author is indebted to Hewitt Wilson. GENERAL DESCRIPTION The term ?clay? includes a great variety of substances that may differ widely in chemical mineralogical and physical properties. No two clays are exactly alike. All of them however, have the prominent characteristic of becoming more or less plastic when wet. Nearly all of the useful clays can be molded into articles, will hold their shape while being dried, and can be converted into a hard, rocklike substance by heat. Clay may, and in fact usually does, consist of a number of minerals among the commonest of which are kaolinite, quartz, feldspar, iron oxides, mica, bauxite, calcite, and manganese oxides. Organic matter is often present. Pure kaolinite, which has the formula A1203. 2 SiO2. 2H2O, is ordinarily, considered to be the parent "clay substance," butt most clays contain other hydrated mixtures of alumina and silica (aluminosilicic acids) along with indefinite amounts of sand and other nonessential minerals3/ Even, this so-called inert matter affects the plasticity, drying shrinkage, ease of drying, and final density, and at high temperatures may react chemically with the clay substance.

Jan 1, 1929

By D. E. Andrews

The objective of this study was to investigate the environmental effects of slaking of surface mine spoils. To accomplish this, both field and laboratory programs were undertaken, supplemented by a thorough literature search. The field program consisted of drilling the highwall as well as test pitting in recent, two-, five, and ten- year-old spoil piles at four active mining sites in the eastern bituminous coal fields. Pertinent observations were made and samples collected for laboratory analyses which consisted of several standard geotechnical, agronomic, and geochemical tests. Durability tests utilized included jar slake, cyclic wet-dry, rate of slake, and slake durability tests. Correlation between field and laboratory portions was made- and results presented. The report is concluded with a discussion of the slaking process and associated environmental impacts, proposal of a preliminary classification system for use in premine planning, and presentation of management techniques to optimize the slaking process.

Jan 1, 1980

This Bureau of Mines report and its companion report (Information Circular 9143) have been prepared to assist in the preparation of prefeasibility type estimates for capital and operating costs of mining of various types of mineral occurrences using current technology. The handbook provides a convenient costing procedure based on the summation of the casts for the unit processes required in any particular mining or mineral processing operation. The costing handbook consists of a series of costing sections, each corresponding to a specific mining unit process. Contained within each section is the methodology to estimate either the capital or operating cost for that unit process. The unit process sections may be used to generate, in January 1984 dollars, costs through the use of either costing curves or formulae representing the prevailing technology. Coverage for surface mining includes dredging, quarrying, strip mining, and open pit mining. The underground mining includes individual development sections for drifting, raising, shaft sinking, stope development, various mining methods, underground mine haulage, general plant, and underground mine administrative cost. This system can be used for estimating cost data for an undeveloped deposit or for checking or verifying mining costs from a developed deposit, with a minimum amount of background information.

Jan 1, 1987

By James Westfield

Drilling for roof bolting has created a new dust problem for the coal-mining industry. Drilling is inherently dusty, and control of dust produced by drilling vertical or nearly vertical holes is much more difficult than control of that produced by drilling flat or down holes.4/ Also, the dust produced by roof drilling differs in composition from that produced by drill-fur, or cutting the coal face because it contains a significantly greater amount of free silica and therefore presents a greater potential hazard of silicosis. Roof bolting has been practiced successfully in the mines of the St. Joseph Lead Co. in southeastern Missouri for over 20 years, but it was not until 1947 and 1948 that large-scale roof-bolting experiments were conducted in coal mines.5/ Although the need for dust control in conjunction with roof drilling was recognized from the beginning, the development and acceptance of roof bolting progressed so rapidly during 1949 and 1950 that solution of the dust problem lagged behind other engineering phases of the technique.

Jan 1, 1951

By J. H. Crary

This report summarizes the results of a one-year agreement for research on the electromagnetic environment in coal mines, which was conceived as the beginning of a long term cooperative program between ITS and the Bureau of Mines. The concepts on which it was originally based are a result of the report on mine rescue and survival by the Committee on Mine Rescue and Survival Techniques of the National Academy of Engineering, dated March 1970. This report drew particular attention to the need for improved communications during and following mine disasters. In particular, the outstanding problems identified were the location of, and communication with, trapped miners. Some tentative solutions, generally involving long-wave electromagnetic signals, were offered. Consideration of the problems of disaster location and communication soon leads to consideration of the communications techniques (or lack of them) for use under normal mining conditions. In particular, if a disaster communication and/or location system is to be readily available and operable under disaster conditions, it should also be usable during mining operations. In this way operators can become familiar enough with the system to operate it during disaster conditions, as well as provide a mechanism for regular testing.

Jan 1, 1972

By H. D. Kline

This publication describes mining and milling methods and costs at the Madison mine of National Lead Co., St. Louis Smelting & Refining Division, in the Fredericktown district of southeast Missouri and is one of a series prepared by the Federal Bureau of Mines on methods, practices, and costs of mining and milling throughout the United States. The are bodies of the Madison mine are known for the complexity and diversity of their are minerals. Sulfides of copper, nickel, and cobalt occur in commercial quantities with lead sulfide, which is the most valuable metallic mineral in are bodies of the Bonne Terre formation in southeast Missouri. Several attempts were made by various operators to mine the complex ores and separate the sulfide minerals before 1927 when National Lead Co. became interested in the Fredericktown district. Operating then as the St. Louis Smelting & Refining Co., the company began mining and milling ores from the Madison mine in 1944 and has operated continuously since then. A recently built refinery produces copper, nickel, and cobalt metal from a concentrate containing iron sulphides and small quantities of copper, nickel, and cobalt sulphides.

Jan 1, 1961

By D. Harrington

Educational campaigns conducted by the manufacturers of explosives, the Bureau of Mines, mining companies, and safety organizations have contributed greatly in reducing accidents caused by explosives arid blasting. Despite these campaigns and the dissemination of information, accidents from explosives and blasting continue to be the direct cause of scores of fatalities and hundreds of nonfatal accidents annually, not only in the mineral industry but essentially wherever explosives are used. The experience of many mining companies and other users of explosives has proved that accidents from explosives can be prevented or averted by the proper training of employees in the handling and using of explosives and by the enforcement of definite rules and instructions for their use. Unfortunately, throughout the years numerous false impressions and ideas have grown up and around the use of explosives. Many of these can be traced back to the manner in which the users of explosives were originally taught, if instructed at all; and as with many types of misinformation in nearly all walks of life, those false ideas are decidedly persistent and being so cause much damage. Many if not most of the users of explosives gained their knowledge of explosives and blasting by watching others and more or less "absorbing" the procedures and thrones of the other fellow, who acted unconsciously as teacher or instructor. A study of explosives accidents reveals the results of such "teachings" when the causes of the accidents are determined, and as might be expected the results very often are far from good. One of the most persistently erroneous impressions or ideas is concerned with the burning rate of safety fuse. Many men with

Jan 1, 1944

By E. O. Binyone

"https://www.youtube.com/watch?v=PBPyGXjlBHIhttps://www.youtube.com/watch?v=3AbtiKOYg7Y&feature=push-fr&attr_tag=uKtVW3yq2ZngptnE%3A6https://www.youtube.com/watch?v=PR2THayf-N8https://www.youtube.com/watch?v=mF-BXiWocqIhttps://www.youtube.com/watch?v=TuesIw-OZA4https://www.youtube.com/watch?v=v2HP7sTIZgEhttps://www.youtube.com/watch?v=v2HP7sTIZgEINTRODUCTIONIn 1937 the Eureka Corporation, Ltd., of Canada obtained a lease on the mining property of the Richmond-Euroka Mining Co. in the Eureka mining district, Eureka County, Nevada. In 1910 the Richmond-Eureka Co. suspended all operations except small-scale leasing, but company and other geologists contended that the El Dorado dolomite would also carry ore in its continuation from fault block north and northeast of the productive old working. The company began to explore the fault block in 1923 by diamond drilling from the,900 level of the Locan shaft, but for various reasons the hole was drilled to a depth of only 2 feet and was then abandoned. Eureka Corporation, Ltd., planned an extensive diamond-drilling program, which included four deep diamond-drill holes, one designated ""A"" fig. if it is to be drilled from the surfaced, and three designated ""E"", ""C"" and ""D"" figs land to be drilled from the 900 level of the Locan shaft. Of these only B and C were completed by the company. Hole C was a contribution,of the hole started by the, started by the Richmond Eureka Co. The site for hole D (figs. 1 and 2) was prepared, but the hole was not drilled. Both B and C holes penetrated sulfide ore carrying good percentages of zinc, lead, gold, and silver. The ore bodies were 40 feet thick and were found approximately 1,400 feet below the 900 level of Locan shaft.On the basis of the very favorable results obtained from the drilling program, the Eureka Corporation planned extensive development of the property and in 1942 commenced sinking the Fad shaft (figs. 1 and 2). The shortage of equipment and materials brought on by the war and difficulties with water in the shaft greatly hindered progress. However, early in 1943 the Eureka Cor¬poration, Ltd., of Canada submitted to the War Production Board a proposal for developing the mine and milling 500 tons of zinc-lead ore a day. The proposal involved an expenditure of $2,890,750."

Dec 1, 1946