Search Documents

By J. B. Gayle

In a modern blast furnace, production depends, to a large extent, on the rate at which the furnace gases can be forced through the charge. Since these gases must make their way through the voids between particles of coke, ore, and limestone, the size and size distribution of the stock-column materials are of considerable importance. Also, because the coke pieces support the weight of the overburden and provide the majority of the voids through which the gases pass, their ability to withstand the shattering and abrading forces to which they are subjected should be related to the maximum obtainable production for any particular furnace. Although the wide acceptance of this point of view is indicated by the ever-increasing demand for stronger and more uniform blast-furnace cokes, economic considerations demand that a quantitative evaluation of the relation between coke quality and blast-furnace performance be made available to the industry at the earliest possible date. The following studies of size-distribution patterns and breakage processes were, therefore, conducted as a part of a preliminary investigation intended as a basis for future studies of the relation between coke quality and blast-furnace performance. The major findings may be summarized as follows: 1. New evidence for the presence of two independent distributions of sizes in run-of-oven cokes has been obtained, and a method for characterizing and estimating the relative importance of the individual distributions has been demonstrated. This method has also been used to study the different types of degradation taking place during the tumbler test.

Jan 1, 1954

The analysis of in-mine grounding systems began with an extensive literature search which is still in progress. About a dozen articles have been found which deal directly with grounding problems on low voltage power systems or mine power systems. These systems have special grounding problems because normal load currents can be nearly as large as many types of fault currents. Information has been collected on the influence of cable spacing) conduit geometry, location of nearby conducting structures, etc., on the magnitude and path of fault current. Many other articles have been found which are less directly related to mine ground system analysis. The in-mine ground system analysis team has also inspected portions of two mine power systems to become familiar with the practices used in grounding. One electrical engineer and several other mine personnel have been interviewed concerning mine power system grounding practice. Already several aspects of the mine grounding system have been marked as requiring special attention.

Jan 1, 1975

The U.S. Bureau of Mines has been concerned for many years with the general problems of underground coal mining and the particular problems due to the methane content of the coal. The Bureau and others have worked diligently to improve the health and safety conditions for underground coal miners. It has been recognized for many years that the methane in coal would have some value if it could he recovered and used, Also its removal before coal mining began or during the mining cycle itself would make mining safer and more economic due to a potential saving in ventilation costs. The work covered in this report was carried out to review methods of removing methane from active and inactive regions of operating coal mines and to determine how the methane could be concentrated and utilized economically.

Jan 1, 1975

By C. E. Gregory

In terms of a Research Proposals supported by a Grant Agreement dated 30 June 1973, the author was commissioned to prepare an annotated bibliography of mine fires. The main objective was to conduct a comprehensive program of library research and search of official files to prepare a list of articles dealing with actual occurrences of mine fires. This bibliography as now completed includes an annotated reference from each article or report cited, underlining the cause, extent, methods used, procedural errors made, results achieved, ventilation effects, and lessons learned from the operation of subduing the particular fire.

Jan 1, 1974

By Eleanor Abshire

This bibliography is the result of a cooperative project undertaken by the Bureau of Ships and the Bureau of Mines to accumulate literature published to date on zirconium and hafnium and to establish an information center on these metals for the use of any interested research organization or library. This bibliography, which will be supplemented as additional information is accumulated, consists of references, with abstracts, to pertinent literature on the subject published from 1907 to date.

Jan 1, 1957

By Richard C. Moore

The U.S. Bureau of Mines contracted a study to review the air and water monitoring requirements of five Federal environmental acts (the Federal Water Pollution Control Act, the Safe Drinking Water Act, the Clean Air Act, the Surface Mining Control and Reclamation Act, and the Resource Conservation and Recovery Act) and to compile information on the currently available monitoring instruments. A literature review of the acts and their associated regulations was conducted to determine applicability to the mining industry as well as any air and water monitoring requirements. In addition, an industry search and literature review was performed to assess the instrumentation available to comply with the monitoring regulations. Based on this research, the instruments are classified by general applicability to air, surface water, or ground water monitoring, then catalogued by monitoring parameters. A discussion is provided on recommended and innovative monitoring techniques.

Jan 1, 1981

By Thomas M. Barczak

State-of-the-art longwall roof supports provide effective strata control, but failures of these support systems still occur. To identify failure mechanisms and the impact these failures have on the safety of the support system, the U.S. Bureau of Mines has been conducting research on shield mechanics in the Bureau's unique mine roof simulator, as well as field studies of in situ support loading and investigations of longwall failures, Three types of failures are discussed: (1) inadequate support capacity, (2) structural failure, and (3) instability. Hypothetical situations with proposed courses of action and case studies of actual longwall failures are described. This information is intended to assist the Mine Safety and Health Administration (MSEIA) and industry mining personnel in safety evaluations of longwall roof support systems.

Jan 1, 1989

By S. H. Ash

THE information obtained by examining and analyzing the core drillings from 15 diamond-drill holes shows that with the proper equipment little difficulty should be experienced while sinking the shafts at the 15 selected sites. Although a number of holes penetrated formations containing a high percentage of silica,, the health hazard from dust can be removed by using proper dust-control equipment. Methane was detected in small amounts in only one (hole 5) of the boreholes. The methane hazard should present no difficulty if adequate ventilation is employed while sinking the shafts.

Jan 1, 1952

By R. B. Krog

As part of its mining health and safety research program, the National Institute for Occupational Safety and Health (NIOSH) conducted a longwall methane emission and mining time study at a mine operating in the Pittsburgh Coalbed to access the methane emission consequences of mining a longer face. The methane emission contributors from the mining of a longwall face are: 1) gas released from the coal broken by the shearer, 2) gas emitted from the coal on the face conveyor, 3) gas emitted from the coal transported on the belt, and 4) background gas emitted from the coal face and from the adjoining ribs. Based on the results of the study, a set of site-specific mathematical formulas and constants were developed to characterize each of the four longwall emission contributors. The mathematical formulas were then applied to longer longwall face mining scenarios to predict the methane emissions from these faces.

Jan 1, 2006

By W. J. Kroll

This investigation was undertaken with the idea of studying a number of unconventional methods for making chromium to determine whether production cost could be lowered and to discuss some of the more recently described processes. These comprise carbon reduction of the oxide in vacuum, nitride dissociation, fusion electrolysis of the chloride, amalgam method, iodide dissociation, calcium reduction of the oxide, hydrogen reduction of the chloride, and reduction of this compound with zinc and with magnesium. Preference is given this latter method, which is shown in a flow sheet. Special attention is given purification of the chloride and separation of the vacuum at about 900° C. A reduction method for the elimination of traces of oxide contained in pure chromium by pure hydrogen obtained from the dissociation of zirconium hydride is described. The various methods are compared in a table in the appendix. Aluminothermic and silicothermic methods for the reduction of chromium oxide and the aqueous electrolysis have been disregarded in this investigation.

Jan 1, 1950

By D. H. Mullen, S. M. Runke, J. B. Cunningham

"SUMMARYThe coarse-grained granitic pegmatities of the United States have long been a source of many important industrial minerals, because of this, they have been studied intensively by geologists, mining engineers, and metallurgists. These studies have amassed a rather astounding array of published and unpublished information.Correlation of geological studies between individual pegmatites, as well as between major districts, has brought forth some semblance of order to the knowledge of the structure and Mineralogical composition of those highly complex and irregular deposits, making it possible to classify certain prgmatitites and pegmatitec zones into several groups of associated minerals; based upon the presence or absence of the minor minerals of beryllium and lithium. This classification or grouping of minerals, with the methods that have been developed for recovering certain of these minerals, makes possible a systematic approach to the winning of many of the industrially important minerals from pegmatite rock by a single integrated process.As the coarse-grained granitic pegmatites are composed primarily of,feldspar, quartz, and muscovite, the methods developed for separating and recovering them, as well as those methods developed for separating and recovering such minor minerals as spodumene and lepidolite, are important contributions to the over-all problem of pegmatite treatment. Some of these methods have been demonstrated in the laboratory only, whereas others have progressed beyond the laboratory stage arid are being employed in commercial operations.Recent laboratory investigations at Rapid City, employing both these early developments and the mineral groupings, have demonstrated that a single integrated process can recover muscovite, feldspar; and. quartz from the rejects of hand-sorting a typical muscovite-feldspar-quartz material. Employing a newly developed procedure for the flotation of beryl, the investigations have also demonstrated the possibility of recovering the beryl, in addition to muscovite, feldspar, and quartz, by an integrated process from a typical berylliferous pegmatitic material in which all of these minerals are present."

Dec 1, 1952

By D. Denton, M. Stickney, R. Langston

The National Institute for Occupational Safety and Health and the Stillwater Mining Company worked cooperatively with the Montana Bureau of Mines and Geology to develop a system that would collect seismic data at the Stillwater and East Boulder mines. The purpose was to obtain baseline information on the magnitude and location of mining-induced seismicity to determine if the mines needed multi-channel in-mine monitoring systems. Seismic data recorded at field sites near the mines are being telemetered via FM radio through a series of repeaters to a central recording site where the seismic signals are digitized using an Earthworm data acquisition system. The Earthworm system performs several data analysis tasks in near-real time and places raw seismic data, preliminary hypocenter locations, and magnitudes on a Website within 5 min of a seismic event. Such rapid access to seismic data allows personnel at the Stillwater Mine, Spokane Research Laboratory, and Earthquake Studies Office to evaluate seismic events quickly and respond in ways that may improve the safety of mine personnel underground. Installation of the system also broadened earthquake coverage to south-central Montana, a region previously not covered by the seismograph network.

By W. W. Adams

With production of coal per man-hour of work at a higher level than ever before, the coal-mining industry of the United States established a near-record in lowering the accident rate of nonfatal injuries per million man-hours of exposure in 1940, the injury rate being lower, except for 1939, than in any year since 1930, the first year for which comparable figures for nonfatal accidents were collected by the. Bureau of Mines, United States Department of the Interior. The rate for fatal accidents, on the other hand, was not as low or favorable as in 1939, nor was it as low as in many years since 1910, the earliest year for which fatality rates were complete for all coal-mining States. Accident and employment reports received from mine operators and fatal-accident reports from State mining departments and inspectors showed that 533,267 men were employed at coal mules in 1940, exclusive of the number employed at coke ovens, Although this number represented 6,108 fewer employees than in 1939, a large increase was made in the volume of work performed and in the quan¬tity of coal produced. In 1940 the amount of labor performed at coal mines was 748 million man-hours, a gain of more than 10 percent over the previous year. The average employee worked 199 days, an increase of 20 workdays per man. Production of coal was nearly 513 million tons, an increase of 14 percent, of which more than 461 million tons was bituminous coal and more than 51 million tons was Pennsylvania anthracite. Accidents to mine workers caused the death of 1,388 employees; in addition, 59,781 employees were injured, and each injury resulted in disability of the employee for more than the remainder of the day on which the accident occurred.

Jan 1, 1942

By Richard E. Thill

The Bureau of Mines' Oil Shale Data Bank (OSDB) was created in 1976 to serve as a centralized source for the storage, retrieval, and dissemination of technical literature, patents, and information on research projects in oil shale. Thousands of bibliographic references, patents, and research projects relating to the mining of oil shale have been identified, abstracted, and indexed according to selected keyword topics. The resulting data bank listings are contained in three sections, each with a separate keyword breakdown for use in rapidly identifying references pertaining to a specific subject. All references cited in the OSDB were published prior to an established cut-off date of May 1, 1981, when a redirection of Bureau of Mines programs resulted in the loss of project funds and the subsequent phasing-out of data bank operations. ACKNOWLEDGMENTS The oil shale data bank listings are the result of a team effort of the project staff. The contributions of Jimaleen Jansma for keypunching, information acquisition, and data entry, and John Brandenburg and Sandra rake for keywording and information acquisition are gratefully acknowledged. Appreciation is expressed to the staff members of the Smithsonian Science Information Exchange, Washington D.C. for their cooperation in supplying data on recent research projects in oil shale for inclusion in the OSDR listings. Appreciation is extended also to the staff of the Gallegos Research Group for assisting with computer services to obtain the final printouts and transfer of files onto magnetic tape.

Jan 1, 1982

By T. M. Barczak, S. C. Tadolini

Reduction in the recovery time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. The recovery entry is developed at the longwall stop position and supported ahead of time so that the required combinations of standing and internal supports can be installed before the longwall face approaches. A calibrated three-dimensional finite element model, developed in conjunction with an underground test area, provided the critical components and design principals for a comprehensive parametric study. The study indicates that vertical, horizontal, and shear stresses concentrated on the outby abutment pillar corner of the recovery room resulting in deformations in the immediate roof above the primary roof support anchorage level. The results of the numerical model and field site observations indicated that the combination of the internal bolting system and the standing concrete supports are critical for the successful and safe extraction of the longwall equipment. Cable supports installed at and angle over the pillars can help stabilize the disturbed zone above the adjacent fender and outby pillars, however; standing supports are required in most sedimentary roof conditions to increase stability and assure a safe longwall extraction.

By David E. Siskind

The U.S. Bureau of Mines and the State of Indiana cooperated with AMAX Coal Co. and its consultants to determine the effects of coal mine overburden blasting on nearby pipelines. Five pressurized 76-m pipeline sections were installed on the Minnehaha Mine highwall near Sullivan, IN, for testing to failure. Four 17-to 51-cm-diameter welded steel pipes and one 22-cm PVC pipe were monitored for vibration, strain, and pressure for a period of 6 months while production blasting advanced up to the test pipeline field. In contrast to previous studies of small-scale, close-in blasting for construction, these tests involved overburden blasts of up to 950 kg per delay in 31-cm blastholes. Analyses found low pipe responses, strains, and calculated stresses from even large blasts. Ground vibrations of 120 to 250 mm/s produced worst case strains that were about 25 pct of the strains resulting from normal pipeline operations and calculated stresses of only about 10 to 18 pct of the ultimate tensile strength. No pressurization failures or permanent strains occurred even at vibration amplitudes of 600 mm/s.

Jan 1, 2010

By Russell E. Griffin

Dielectric constants and dissipation factors were measured by the Bureau of Mines for 13 simulated lunar rocks over the 20-to 100-megahertz frequency range by means of the susceptance-variation method. Measurements were made at room temperature and normal atmospheric pressure. Results are presented and some comparison is made with data reported by others. The rocks used include a broad range of physical characteristics and chemical compositions from the large areas of volcanism in Oregon and northern California, and two nonvolcanic types. These rocks make up a suite of rock standards used by a group of laboratories engaged in lunar research. The data presented will add to the basic scientific and engineering knowledge needed to utilize extra-terrestrial mineral resources for support of future space missions.

Jan 1, 1974

Develop tools that mine personnel can use to comply with 30 CFR,Part 47. Background The new MSHA rule, 30 CFR, Part 47 (also known as the HazCom rule), requires all mines to develop a written program to track hazardous chemicals at their sites. More specifically, the rule requires that mines list all chemicals and determine which are hazardous; develop a written Hazard Communication Program; label all containers used to store hazardous chemicals; obtain or develop Material Safety Data Sheets (MSDS) for all chemicals stored or produced; provide miners with training in working around hazardous chemicals; and make information about hazardous chemicals available to all workers. All mines with six or more employees must have complied with the new rule by September 23, 2002, and mines with five or fewer employees will have to be in compliance by March 21, 2003.

Mar 1, 2003

Mercury has been used by mankind since prehistoric times. It has been, and is now, widely used in industry and medicine and has unique properties which make direct substitution difficult or impossible. At present its principal uses are for electrical apparatus, control instruments, electrolytic soda preparation, mildew-proofing paints, pesticides, and medical and dental preparations. Deposits of mercury are less common than those of other base and precious metals, but some of the deposits are very large and have been ample to meet the world's past demands. The price of mercury has had many sharp fluctuations, but in general, the limited number of producers has resulted in a more stable price structure than that of many other commodities. The United States has been one of the main producers of mercury, and from 1850 to 1961 produced 3,247,704 flasks. Yearly production since World War II has varied from 4,535 to 38,067 flasks. An estimate of domestic resources of mercury producible at various price ranges was prepared for each mercury mine by combining specific knowledge of mercury mineralization with estimates of potential, based on geologic information and past production history. The sum of the individual estimates for each price range is shown in a table. A parallel estimate of nationwide production potential was made from a study of past price and production relationships. These were analyzed by plotting yearly production figures against the previous year's price, expressed in dollars of constant purchasing power. An equation was fitted to the data by mathematical means and was used to extend the curve into areas of higher than historic prices. Potential production rates at various price levels were taken from this graph. The estimated yearly production rates were used to make an estimate of total potential based on the premise that production rates and reserves have a proportionate relationship. The rate of developing mercury reserves during the period from January 1944 to January 1962 is considered, and it is shown that if this rate can be continued, the mercury resources of the United States, at a constant dollar price of $500 per flask, are adequate to support a production of 60,000 flasks per year for 30 or more years. This publication contains a history and description of the mercury industry in every State which has had production and individual descriptions of all mercury properties which have reported significant production. Accompanying tables give the important facts about all known mercury occurrences.

Jan 1, 1965

Mercury has been used by mankind since prehistoric times. It has been, and is now, widely used in industry and medicine and has unique properties which make direct substitution difficult or impossible. At present its principal uses are for electrical apparatus, control instruments, electrolytic soda preparation, mildew-proofing paints, pesticides, and medical and dental preparations. Deposits of mercury are less common than those of other base and precious metals, but some of the deposits are very large and have been ample to meet the world's past demands. The price of mercury has had many sharp fluctuations, but in general, the limited number of producers has resulted in a more stable price structure than that of many other commodities. The United States has been one of the main producers of mercury, and from 1850 to 1961 produced 3,247,704 flasks. Yearly production since World War I1 has varied from 4,535 to 38,067 flasks. An estimate of domestic resources of mercury producible at various price ranges was prepared for each mercury mine by combining specific knowledge of mercury mineralization with estimates of potential, based on geologic information and past production history. The sum of the individual estimates for each price range is shown in a table. A parallel estimate of nationwide production potential was made from a study of past price and production relationships. These were analyzed by plotting yearly production figures against the previous year's price, expressed in dollars of constant purchasing power. An equation was fitted to the data by mathematical means and was used to extend the curve into areas of higher than historic prices. Potential production rates at various price levels were taken from this graph. The estimated yearly production rates were used to make an estimate of total potential based on the premise that production rates and reserves have a proportionate relationship. The rate of developing mercury reserves during the period from January 1944 to January 1962 is considered, and it is shown that if this rate can be continued, the mercury resources of the United States, at a constant dollar price of $500 per flask, are adequate to support a production of 60,000 flasks per year for 30 or more years. This publication contains a history and description of the mercury industry in every State which has had production and individual descriptions of all mercury properties which have reported significant production. Accompanying tables give the important facts about all known mercury occurrences.

Jan 1, 1965