Search Documents

By G. St. J. Perrott, G. W. Jones

"In the course of its investigations pertaining to the promotion of safety the Bureau of Mines is actively engaged in investigating all promising materials that may be of value in rendering methane or other combustible gases, vapors, or solids less inflammable.Added substances are of value if such additions narrow the limits of inflammability, raise the ignition temperature, lower the speed of propagation of flame, or reduce the maximum pressure developed. Of major importance is the effect of added materials on the limits of inflammability, because methane is the chief combustible s liberated in mines, considerable work has been done with extinguishing agents on methane flames. For obvious reasons, a substance to be of value for the extinction flames should be a gas, or a liquid having a sufficient vapor pressure to give concentrations of the vapor in sufficient amounts to extinguish the flames or markedly narrow the limits of inflammability. The substance should be nontoxic, cheap, and noncorrosive and must be incombustible. Solids, such as rock dust, are undesirable and of little value for combustible gases because they soon settle out of the atmosphere, and their flame- extinguishing value is thereby lost. There are at present only a few gases and vapors-for example, nitrogen, carbon dioxide, and carbon tetrachloride-which meet these requirements.The extinction of methane flames by nitrogen, carbon dioxide, and argon has been reported by Coward and Hartwell 4; the extinction by water vapor by Coward and Gleadell 5, and the extinction by helium and carbon tetrachloride by Coward and Jones 6."

Oct 1, 1930

By E. A. Mihok

A pilot plant for treating mine drainage by neutralization with limestone was designed, fabricated, and operated by the Bureau of Mines. The process consists of (1) producing a very fine (minus 400-mesh) limestone slurry, (2) mixing the slurry with the mine water, (3) aerating the resulting mixture to remove carbon dioxide and precipitate iron, and (4) separating the solids from the liquid by sedimentation. A mine discharge of pH 2.8, containing 1,700 ppm total acidity, 36 ppm ferrous iron, and 360 ppm total iron, was treated at rates from 300 to 400 gpm. The treated water ultimately reached a pH of 7.4 and contained no detectable iron. The resulting sludge compacted to approximately one-third the volume of sludge from mine water neutralized with lime. The advantages of the limestone process, compared with the conventional lime process are as follows: Widespread distribution and lower cost of run-of-mine, indigenous limestone; simplicity of plant design; reduced hazards and plant operating and maintenance costs accruing from the use of a less reactive chemical agent; higher solids concentration of the precipitated sludge; and no deleterious effect caused by accidental overtreatment. While total process costs could not be determined, it is conservatively estimated that the cost of treating mine water by the limestone process is one-third to one-half the cost of the lime process, depending on the characteristics of the water to be treated and the availability and quality of limestone used.

Jan 1, 1968

By Jonathan E. Ludlow

A field test was conducted to demonstrate and quantify the relationship between deep cutting and the creation of airborne respirable dust for longwall mining With a double-ended ranging drum shearer. The testing program was carried out on the 3 North longwall of North American Coal Company's Quarto No. y mine in Claringten, Ohio. Continuous recordings of the dust levels were made at both the midface and tail ate areas. Data were collected during 27 shifts during which time 81 complete mining, cycles took place. Both drum speed and the number of picks per line were varied systematically during the testing program to alter the depth of cut while the production rate was held constant by maintaining a constant haulage speed. The test results indicated that at the midface position, airborne respirable dust was strongly dependent upon the depth of cut as influenced by both the drum speed and number of picks. Drum speed had a much stronger effect than number of picks over the experimental range, since a halving of drum speed reduced dust levels by approximately 60 percent while removal of every other vane pick resulted in only a 2.1 percent reduction at constant production. At the tailgate position, however, neither effect was strongly apparent. A tendency for the slower drum speeds to he associated with reduced power consumption and higher haulage speeds (and therefore production rates) was also noted. It is recommended that longwall operators oper¬ate at the lowest available drum speed wherever possible.

Jan 1, 1981

By James S. Browning

Recovery of fine mica from a sample of impounded tailing from the Dixie Mines, Inc., crushing and screening operations, Heflin, Ala., was investigated to determine if plant losses of mica could be reduced while econmically producing a commercially acceptable mica concentrate. Conventional wet-tabling and agglomerate-tabling methods yielded concentrates assaying about 95 percent mica from the tailing that contained 17 percent mica. Products containing about 98 percent mica and accounting for mica recoveries of 86 percent were obtained by flotation, using as reagents sulfuric acid, kerosene, and coco amine acetate (a mixture consisting chiefly of dodecyl and tetradecyl amine acetates). The results of the batch flotation tests were verified by tests in a small continuous flotation pilot plant.

Jan 1, 1963

By Frank T. Greene

An investigation of the quenching behavior of coal dust-air flames was carried out. The literature relevant to coal dust-air flames was reviewed, including information on the agglomeration, sedimentation, and dispersal of dust clouds. The simple equations relating the various concentrations involved in dust flame propagation are given and their implications elaborated. It is shown that the concentration seen by a moving flame in a sedimenting dust cloud can differ significantly from the concentration commonly measured in such experiments. The known dust cloud phenomena which appeared significant in flame propagation studies were experimentally evaluated, and quenching diameters, flame speeds, and lean propagation limits for several tube diameters measured. For Pittsburgh seam coal, the Minimum Quenching Diameter (MQD) for dust between 10 and 20 µm was found to be between 0.7 and 0.8 cm, and the lean propagation for 3.2-cm tubes to be approximately 200 mg/liter. Similar MQD data were also obtained for Pocahontas and Sewell coals, Beulah lignite, and a 50-gal./ton oil shale. The effect of temperature, coal particle size, and propagation tube material were also investigated.

Jan 1, 1981

By D. A. Wilson

A cyclic leaching process was developed for selectively leaching and recovering cadmium from nickel-cadmium scrap battery waste. The six major steps in the process are the following: (1) washing the plates to remove KOH electrolyte, (2) roasting at 550° to 600° C to oxidize metallic cadmium and decompose cadmium and nickel salts, (3) leaching with an ammonium nitrate solution, (4) precipitation of the leached cadmium from solution as cadmium carbonate using CO2 gas, (5) removal of CO2 from the lixiviator by adjusting to pH 4.5, heating, and evacuating the system, and (6) removal of small amounts of leached nickel from the lixiviator using a solvent extraction technique. The regenerated lixiviator is then recycled to leach additional plates. Cadmium extraction was 94 percent and the cadmium carbonate product contained 0.14 percent nickel and 0.12 percent cobalt impurity. The leached plates were smelted to a high nickel-low iron alloy with no detectable amounts of cadmium.

Jan 1, 1971

By F. J. Perzak

The Bureau of Mines conducted a flammability study of plastic ventilation ducts. Six rigid 16-in-diam fiberglass-reinforced plastic ducts from five manufacturers were examined using laboratory-scale, large-scale, and full-scale fire tests. The laboratory-scale tests included the American Society for Testing and Materials E162 radiant panel test, the E2863 oxygen index test, and the standardized small-scale flammability test (S3FT) developed by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and replicated by the Bureau of Mines. Ten-foot lengths of the same ducts were also subjected to a large-scale vertical fire test, and 20-to 30-ft lengths were tested in a full-scale in-mine fire test at the Bureau's Lake Lynn Laboratory mine. The data from the laboratory-scale radiant panel test and oxygen index test indicated that the ducts were fire-resistant, However, five of the six ducts failed the S3FT and vertical fire tests, and four of the ducts failed the full-scale in-mine tests with flame propagation rates that ranged from 3 to 10 ft/min. The results indicate the need for improved fire-resistant plastic ducts. The good agreement between the S3FT re-sults and the vertical and full-scale tests show that the S3FT provides a good indication of the flammability of fiberglass-reinforced plastic ducting under realistic fire conditions.

Jan 1, 1987

By Fred S. Karn

Inhibitors are used in coal mines as a precaution against accidental dust explosions. Although rock dust is the usual inhibitor many others have been tested. To facilitate testing a screening process using laser irradiation was proposed. The procedure includes irradiation of a coal-dust mixture followed by mass-spectrometric analysis of the evolved gases and an evaluation of the flammability characteristics of the gases. Carbonate-type inhibitors decreased the percentage of combustibles in the gases generated and inhibitors like NaCI (thermally stable salts) decreased the total gas generated. A suitable test procedure did not result from the investigation, demonstrating the inadequacy of fast heating, non-combustive techniques in rating inhibitors of coal dust explosions.

Jan 1, 1973

By J. Douglas Causey

In 1988, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied part of the 12,740-acre Blue Canyon Wilderness Study Area (OR-003-073) in order to evaluate its identified mineral resources. The study area is in Malheur County, OR, about 27 miles northwest of Jordan Valley. The study area is underlain by Tertiary welded tuff, tuff, perlite and tuffaceous sedimentary rocks capped by basalt. Jasper has been mined from several localities. Some mining has been done by hobbyists. However, the area has been covered by mining claims since 1964, with mining done by commercial operators. This region has been a source of "Owyhee picture" and other similar jaspers. More recent exploration has focused on the gold potential of nearby areas such as Quartz Mountain and Red Butte.

Jan 1, 1989

By Robert L. Lagace

This report presents a mathematical model for the propagation of UHF radio waves in the large cross-section tunnels of a room and pillar limestone mine, and describes the analysis of a small amount of propagation data obtained in a limestone mine. The model and analysis is based on the waveguide mode theory developed earlier for the transmission of UHF waves in coal mine tunnels, with allowance for propagation losses due to refraction into the tunnel walls, to scattering by wall roughness, and to long range random tilt of the walls. Propagation around corners and through pillars is also examined based on a ray theory approach, together with the beneficial effects of placing reflectors at intersections to significantly reduce corner losses. The theory is found to be in fair agreement with the data; however, additional in-mine measurements are needed to provide a more conclusive test of the model.

Jan 1, 1979

By Richard L. Fowler

[Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting, obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the bear overage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve completely self-contained shuttle car system which responds to the mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to valuate various guidance techniques during the feasibility study. Subsequent simulation rues were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing wan performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated Chi predicted performance capability during underground face haulage tests. Dust did not Impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance Closed loop steering control with manual override is recommended o: mended for the lateral guidance e system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.]

Jan 1, 1973

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude run to stills. Furthermore, the premise the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By E. H. Izen

A thermal imaging borehole probe was designed and fabricated for the purpose of obtaining thermal images, through smoke, of objects and people in underground mines. The effort was basically unsuccessful; electrical noise, and possibly thermal noise, interferred with the desired signals to the extent that spatial resolution in the images was unacceptable.

Jan 1, 1980

By J. C. Engel

Recent innovations in mine safety include the use of mercury vapor lamps for mine vehicle illumination. Such lamps, however, extinguish whenever the line voltage at the machine momentarily sags or is interrupted. The lamps must then cool for several minutes before they will restart. By supplying reduced high frequency power to the lamps from an auxiliary source, it is possible to maintain ionization in the arc tubes preventing the lamps from extinguishing. Essentially an auxiliary high frequency supply, the keep alive system provides additional power to the lamps automatically whenever the lamps are in danger of dropping out. The system can also provide the operator with the ability to dim the lamps at will for periods of up to three minutes by simply interrupting the 60 Hz power to the conventional ballasts. Each unit, housed in a steel explosion proof enclosure with a volume of approximately 0.6 ft3, is capable of servicing up to six 175 watt H-39 mercury lamps and two 100 watt H-75 reflector flood lamps. A total of 16 units were produced for the USBM under this contract and its extension.

Jan 1, 1979

By S. J. Rodgers

This report presents the results of in-mine studies to determine the severity of dust sources in conventional mining operations. Three underground coal mines were surveyed using gravimetric samplers and GCA RAM-1 continuous dust monitors. Two additional mines were surveyed using only GCA RAM-1 monitors. Data on dust control methods were acquired during the survey, also. The results indicated that cutting/drilling and loading out were the dustiest operations during a conventional mining cycle. Roof bolting, shot firing and product transport were less severe dust sources.

Jan 1, 1983

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude runs to stills. Furthermore, the premise -the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By Thomas L. Theis

The use of a suspended growth system of T. ferrooxidans attached in a film to individual particles of bentonite and operated as a sequencing batch reactor has been shown to be a practical way of oxidizing ferrous iron in acid mine drainage. This component followed by limestone neutralization is both a technically and economically feasible approach to the treatment of these wastewaters in comparison to existing and proposed methods. The advantages, in addition to less expense, are greater safety, acceptable treatment at a lower pH, lower solids buildup, less danger of overtreatment, and greater flexibility in operational characteristics. In this report data on the continuous bench scale operation of the system under a variety of conditions shows sustained levels of oxidation in excess of 9%. A cost analysis projects capital and operating costs of $80/1,000 m3 of wastewater.

Jan 1, 1982

By Donald O. Capstick

A mineral survey of a 5,700-acre portion of the 11,510-acre Upper Deep Creek Wilderness Study Area (ID-111-44B) in southwestern Idaho was conducted by the U.S. Bureau of Mines in 1985. No mining claims have been located, no minerals have been produced, and no resources have been identified in the study area. Three reconnaissance samples of alluvium from the Deep Creek drainage contained $0.21, $0.22, and $2.72 per cubic yard in placer gold, higher than usual for the Owyhee River canyonland area. The samples of near-surface material contained very fine gold in values too low to support large-volume commercial placer operations, but the quantity and size of the particles of gold in the alluvium is expected to increase near bedrock. Consequently, the area may be a target for recreational as well as small commercial suction dredge operations. The physical characteristics of the individual pieces of gold (bright and angular) indicate that it may have recently come from an unidentified nearby source.

Jan 1, 1986

By Michael Hamilton

Mineral resources have been identified at seven properties in the, Middle Fork Judith study area (fig. 1, and table 1). Commodities consist of silver, gold, copper, lead, zinc, and marble. Eleven properties (fig. 1 and table 2) have potential for discovery of silver, copper, lead, zinc, or sapphire resources. Of principle interest are the mineral deposits within contact zones between the Yogo intrusive complex and the surrounding Paleozoic sedimentary rocks. Contact alteration zones along the southern slopes of Yogo Peak have been prospected in a 2- to 3-mi (3.2-to 4.8 -km) long belt within the study area.

Jan 1, 1982

By Michael E. Meadows

The results of tests to determine the .regional applicability of four synthetic unit hydrograph models are presented. The SCS curvilinear (Haan), SCS single triangle, Williams and TVA double triangle unit hydrograph models were tested on 271 events from 38 USDA experimental watersheds in 14 physiographic provinces. Though inconclusive due to the limited number of events analyzed, the results indicated a regional tendency for each model, with the SCS curvilinear unit hydrograph method generally performing best overall. It outperformed the SCS single triangle by predicting better shape; they differed less than 2 percent in time of peak and peak rate predictions. The Williams model performed well at Oxford, Mississippi and Coshocton, Ohio, which suggests it may be applicable to surface mined lands within the Northern and Central Appalachian Plateau and Texas coal producing regions. The TVA model is applicable to the Appalachian Plateau, specifically the Cumberland Plateau. A second test using only the SCS curvilinear unit hydrograph on 11 small watersheds and 50 events was conducted to investigate the effect of the excesss rainfall pattern on simulation results. A Green and Ampt infiltration model was coupled with the SCS unit hydrograph model to determine if peak rate and timing errors noted in the regional test could be minimized with an alternate to the SCS curve number model for determining infiltration losses. The results confirm the curve number model is the better approach to determining the excess rainfall pattern for unit hydrograph simulation.

Jan 1, 1983