Search Documents

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent, high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptablecomputational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By Mark Bauckman

Discussion Topics • Market Needs • Technology Developments & Best Practices • Industry & Government Developments • Future Possibilities & Your Role

Jan 1, 2006

By Raden Haris Handayana, Jihan Farhan Lubis, Milia Putri, Tengku Deli Hamonangan Hasibuan, Sani Salahudin

An environmental issue that must be controlled from coal overburden blasting near the structure is ground vibration. Damaging ground vibration is the effect exerted from residual energy from blasting that does not work to fracture the rocks. Sebuku Tanjung Coal is a coal mining that operates T3 Pit adjacent to the High Voltage Tower. This structure is included in the Class 5 building with a maximum Peak Particle Velocity (PPV) of 40 mm/s. The shortest distance from the blasting location to the structure is 105 m. The initiation system used is electronic detonators combinate with emulsion as an explosives type. In Indonesia, the government regulated vibration limitation on SNI 7571:2010. The blast outcomes targeted are PPV below 40 mm/s, fragmentation size <80 cm for Excavator Komatsu PC-2000, and digging time <12 seconds. In this paper, the blast design was engineered by conducting Signature Hole Analysis for optimizing delay timing configuration and Scale Distance regression analysis to determine optimum charge weight per delay at the blast site. PPV results from 30 blastings achieved 100% below 40 mm/s with the range of about 1.773-30.250 mm/s. The deviation between PPV prediction to PPV actual is less than ±18% which provides the blasting with electronic detonator resulting in good PPV prediction for controlling vibration. The average fragmentation size (D80) is 55.81 cm in the 1st layer and 54.81 cm in the 2nd layer. The average digging time is 10.30 seconds in the 1st layer and 10.12 seconds in the 2nd layer.

Feb 6, 2023

By Rob Lederer, Chris Batten

Traditionally coal model digital terrain models (DTM) are created from lithological information obtained from broad scale exploration holes. The grid layout and distance between holes means that models do not commonly display local variations of seam dip, faulting and shearing. Due to this, issues can often arise when designing the loading of blast patterns based on potential variances between model and actual coal seam locations. Many sites will often attempt to create more accurate models through the collection of data from coal edge pickups on highwalls and in blast faces, along with information recorded by drillers (touch coal holes) from both production and presplit holes for both the current and previous blasts.

Jan 1, 2012

By G Mendoza, L Taddei, C Robertson

It is a well-known industry fact that many mine sites around the globe experience blast holes that have elevated temperatures due to reactive ground, geochemical reactions, geomorphic reactions, sub level open fires, etc. It has been reported in many previous industry publications (White, Saputra et al) that elevated blast hole temperatures are a norm at many mine sites and are dealt with on an ongoing basis while the drill and blast process continues under elevated states of alert. The choice of explosives products including the type of detonator, primer, accessory, and bulk product all must be taken into consideration when loading blast holes where there is a known potential for elevated temperature conditions. It should also be noted that these elevated temperatures inside blast holes can be consistent throughout the blast hole length or vary in position within the blast hole depending on the mine conditions mentioned in the opening statement above. The risks associated with the loading of primers and bulk explosives in holes where elevated temperatures are present include: the ejection of the bulk explosives product, deflagration of the explosives during initiation of the blast or premature and uncontrolled initiation of a blast hole(s). This paper describes a unique and novel approach to the active monitoring of the temperature within blast holes with the application of electronic detonators with integrated temperature measuring (ITM) capabilities, deployed and demonstrated at a mine site in Mexico during January 2023 to March 2023. The deployment of ITM capable electronic detonators allows a user to monitor and record the real time temperature at multiple locations (e.g., toe, middle and collar) at each electronic detonator’s position within the blast hole, with the ability to react instantaneously to elevations in temperature reported. The measurement of the temperature can be for a single ITM electronic detonator, or simultaneous for an array of ITM electronic detonators, allowing for the potential for the data to be represented by a time/temperature/hole depth three-dimensional heat map. Changes in temperature at different borehole positions can vary, however, often the collar position is expected to be the most reactive due the combination of bulk explosive product and oxygen exposure, which can be confirmed with the application of the ITM electronic detonators. A mine site’s reaction to a measured elevated temperature within a blast hole can vary depending on the temperature measured and the change in temperature from the last measurement made. The study was found to produce real-time in-hole temperature information which was previously unobtainable without the introduction of another device. New and adaptive elevated temperature hole policies can be created and adapted proactively as real time information is received, leading to a safer mining operation.

Jan 21, 2025

By Wilfrid Comeau

The RICHTER scale is used in classifying earthquake severity. It is an energy scale giving the estimated energy liberated at the source of the earthquake. Earthquake damage on the earth’s surface, for example at the epicenter - spot on the earth’s surface directly above the earthquake, for a given RICHTER number can vary. This depends on the depth of the earthquake focus. Deeper earthquakes will generally cause a lower level of damage at the epicenter but the damage will be spread over a greater area. As mentioned by Randy Wheeler on Blastserve, each successive RICHTER number represents about a 30-fold increase in energy. This scale is open at both ends with “0” RICHTER equal to about 104 Joules. The lowest level detected by sensitive instruments is about 2 on the RICHTER scale or about 107 Joules. The highest-level earthquake detected at 8.9 RICHTER represents a release of about 3 x 101 7 Joules.

Jan 1, 2003

By Michelle Crull, Susan Hamilton

Explosives safety requirements in the United States began in 1909 when the American Railroad Institute questioned explosives manufacturers regarding distances necessary to protect employees and property. In response to this inquiry, a group of explosives manufacturers collaborated to study over 200 explosive accidents. This study resulted in the 1914 American Table of Distance (ATD) published by the Institute of Makers of Explosives (IME). The 1914 ATD provided suggested separations between explosives and inhabited buildings, public highways, and public railways.

Jan 1, 2010

By Aris Tambunan, Nella Lubis, Nurafrianti Saala, Komang Widhiayanto, Herry Saputra, Rudolf Sitorus

Maximizing mining recovery rates and minimizing ore loss are pivotal objectives for economic efficiency and operational effectiveness. This study explores methods to address these imperatives by enhancing ore production and recovery through improved blasting techniques and spillage control in the Martabe Gold Mine Project in North Sumatra Province, Indonesia. Between 2018 and 2021, the average mining recovery rate stood at 93%, resulting in a potential annual ore loss of 7% and a potential quarterly financial impact of close to $2 million. Maintaining and enhancing mining recovery became crucial, with a planned 30% increase in total material movement for 2022. The mining recovery target for 2022 was set at 96% based on best achievement historical data from 2021 to increase ore tonnage by 203 KTon per annum. To achieve the primary objective of increasing ore production by improving mining recovery, the study focused on predicting and controlling the movement of blasted ore to reduce spillage and enhancing the grade control model to reflect actual conditions post-blasting. Several alternative solutions were explored, primarily emphasizing drilling and blasting activities. Essential methods included capturing the actual blasting movement to adjust the ore block based on blasting design data and post-blasting muckpile topography. This approach minimizes ore loss by providing output as ore block adjustment based on post-blast movement data. In addition, the tie-up design was adjusted to control ore spillage outside the pit ridge. The implementation of these methods yielded significant improvements. Adjusting the ore block based on actual blasting movement contributed $1,545,764 in benefits. Controlling ore spillage outside the pit ridge achieved a 10% reduction in spillage, contributing $79,184 in benefits. These enhancements successfully met the 2022 mining recovery target of 96%, marking a 3% increase from 2021. Consequently, ore loss was reduced by 178 KTon throughout 2022, resulting in a financial impact of $7.3 million. The study underscores the significance of precise blasting techniques and effective spillage control in enhancing mining recovery rates.

Jan 21, 2025

By D. Scott Scovira, Remi Proulx

The Meikle Mine is a high grade, underground gold mine utilizing primary-secondary longhole open stoping with delayed backfill to produce 3000 stpd of ore. Hot and reactive ground conditions were encountered early on in the mine life. Ground temperatures up to 330” F were measured. In the early stages of mining, the mine experienced premature detonations using different explosives. The learning curve to safely mine this high-grade gold deposit in hot and severely reactive ground was indeed very steep. Currently, the Meikle Mine uses a special buffered bulk emulsion in all blasts to address hot and reactive ground concerns. In addition, exacting procedures are also followed to ensure safe work with explosives. The combination of new explosives technology and strict loading procedures permits high mine productivity with the highest degree of safety.

Jan 1, 2000

By W. Sharkey Bowers

This study was undertaken in order to determine a conservative estimate of the attenuation rate of vibrations through the shallow limestone in South Florida due to quarry blasting.

Feb 1, 2020

By Tyler Rockley, J. P. Remi Proulx, Ruilin Yang

A highwall blast vibration project was carried out to quantify the level of blast vibrations produced from a trim blast in soft rock and a combined production and trim blast in hard rock. Combining production and trim blasts could be performed without exceeding the mine’s vibration limits.

Feb 1, 2020

By Deepesh Yadav, B. S. Choudhary

Underwater drilling and blasting is conducted for deepening of sea channels for port berths, lake or reservoirs for water supply etc. so that rock dredging becomes easier. During this process there are several associated unwanted effects having potential to cause damage to surrounding structures and the environment, flora and fauna. Though all these ill effects can’t be completely eliminated but adopting controlled blasting techniques can minimize these to tolerable levels. It is recognized that ground vibrations resulting from rock blasting below water near dam may endanger the safety of earthen dams. Therefore, controlled blasting technique was used to ensure the safety of dam and its efficacy was established by monitoring of blast vibrations. The usage of small quantity of explosives confined in blast holes, non-electrical delay detonators and initiating each hole with a separate delay helped to minimize the ground vibration effects on surrounding structures.

Jan 1, 2018

By Andrew Moore

It has long been common practice to conduct drilling and blasting operations at surface quarries in the Midwest in close proximity to near-vertical highwalls. The main reasons for such an approach, and the limited use of adequate safety controls, can be associated with higher costs, operational constraints, lithological requirements, property boundary restrictions, inadequate quarry planning, or a lack of understanding of highwall risks. Working in proximity to highwalls, without effective controls, exposes personnel and equipment to increased risk of incidents. In recent history, there have been isolated incidents involving equipment damage, or personnel injury/fatality around the United States. However, the Midwest market has largely escaped the effects of such incidents, even though the exposure rate is high. Awareness about this matter greatly increased on January 19th, 2021, when a significant incident occurred at a quarry near Green Bay, Wisconsin. As a crew was loading a typical blast near a highwall, a ground fall occurred, and multiple rock fragments struck a laborer working on the bench below. This individual sustained significant and life-altering injuries.

Feb 6, 2023

By Sedat Esen

"This paper presents a critical review of the fragmentation data obtained from some large open pit copper and gold mines. Database ncludes 35 mines with Uniaxial Compressive Strength values ranging from 19 MPa to 227 MPa (2756 psi to 32923 psi). Variation in the fragmentation data and the causes are discussed in detail. Quality assurance/quality control (QA/QC) in drilling and blasting was shown to have significant impact on fragmentation. In addition, controllable blast design parameters including drill pattern, powder factor, blast timing, stemming length, etc as well as the large blast sizes havesignificant potential to improve fragmentation. Feed size requirements of crushing and grinding circuits were discussed in detail. The paper discusses the effects of different size fractions (top size, 80 %passing size and % passing 10 mm (0.5 in)) on the downstream processes and the role of the fragmentation model in the mine to mill process. Blast domains based on rock strength and structure canbe established by using a fragmentation model which is calibrated using measured fragmentation data. This allows the blast engineer to compensate for changing rock characteristics and stabilize the ROMfragmentation size and result in increased crusher and mill throughput. Two case studies were presented to demonstrate the benefits achieved in downstream processes. Main benefits were reduced downtime at crusher circuits, improved mill throughput as well as reduced total operating cost. A simple relationbetween uniaxial compressive strength and powder factor was proposed using the database for the optimized mines as a guideline to allow site engineers to compare their sites against the other sites."

Jan 1, 2017

By J. Sanchidrián, A. Fernández, P. Segarra

The combination of chemical analysis techniques as XRF and measurement-while-drilling (MWD) technology in underground mining is a novel approach to gather comprehensive on-line information about physical and mineralogical data. In this work their integration is investigated aiming to delineate the ore/waste boundary. The input data analyzed come from a narrow vein underground mine, where the ore correspond to fluorite, and gathered in two production levels with complex mineralogical characteristics. Two approaches are followed to build a generalizable classification methodology and a site-specific model: a k-means clustering heuristic algorithm to define rock classes based on their physicochemical features, and a machine learning (ML) ensemble model trained with drilling parameters. For an imbalance class problem, a good recognition is obtained for the ore when is related to a high content of silica and for the waste. To predict the ore with low silica content it is necessary to integrate an analysis-while-drilling method to recognize the fluorite content when this mineral is embedded in different rocks. MWD can be employing for the lithologies recognition when representing different structural and mechanical properties between them.

Jan 1, 2024

By Gerard McAlinden, Daniel Frost, Patrick McAlinden, James McAlinden

In an effort to recover Polychlorinated biphenyls (PCB’s) that had leached into bedrock below the Hudson River in Upstate New York, a shaft and tunnel complex was designed that would allow installation of inclined and vertical wells into the zones of contamination to recover PCB’s by gravity. A joint venture of Merco Inc., of Lebanon, NJ, and Obayashi Corporation, of San Francisco, CA, was awarded the contract for constructing the first Tunnel Drain Collection System in the world. Conventional drill and blast techniques were the most economical method to construct the project but due to the presence of PCB’s and community concerns, innovative drill and blast practices were needed.

Jan 1, 2010

By Drew Martin

In March 2010 the Boral Linwood Quarry, Adelaide South Australia, implemented the blasting contractors Monte Carlo Blast Vibration Model as part of their blast design process. The Linwood Quarry was developing an area where blasting activities were marginally complying with the statutory vibration limits. Compliance to the statutory limits was only being achieved through the use of small blasts (less than 15 000 T (14 763 ton)) at a high cost to the quarry.

Jan 1, 2012

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"The urgent need for improvements in the control and mitigation of environmental and social conditions associated with the extraction and processing of raw materials is increasingly a demand imposed by legal entities and institutions. Therefore, this present article proposes an improvement of the estimation in the magnitude of the vibrations resulting from rock blasting methodologies in the surrounding areas,incorporating the heterogeneity caused by uncontrollable parameters, such as geological andgeotechnical characteristics. This methodology combines the use of empirical vibration attenuation lawscommonly known and with terrain discretization techniques using Voronoi’s decomposition. For thevalidation assessment of this methodology, the data set collected and compiled is composed by 87 vibration measures collected in 16 sample points in one area of study of which 2/3 of the samples were used to create the model and 1/3 for the validation. Using normality tests for statistical residue analysis,it is possible to infer that this present model has null residual mean, as well as a smaller sum of residualerrors. Comparing the methodology present in this paper with the procedures executed nowadays, areduction of the errors associated with the estimation is obvious, highlighting a better characterization of the behavior of the vibrations associated with rock blasting."

Jan 1, 2017

By Jeff Hiedeman, Clint Sestrich, Christopher Hyle

Westslope Cutthroat trout have declined in distribution and abundance across their range and currently occupy about 59% of their historic habitat. Due to hybridization with non-native species such as rainbow trout, genetically pure populations persist in only 10% of that range. A westslope cutthroat trout population with relatively high genetic purity (97%) and conservation importance persists in less than two linear stream miles in the headwaters of the South Fork Madison River in southwest Montana. The relative purity of this population has been maintained through the presence of a downstream intermittent reach. However, spring flows fill the intermittent reach, creating a connection between occupied westslope cutthroat trout habitat in the headwaters and the habitat of competing trout species downstream.

Jan 1, 2011

By Thomas E. Ricketts

Occidental Oil Shale Inc. has spent the last eight years at its Logan Wash. mine near DeBeque, Colorado, developing its modified in-situ oil shale process for obtaining oil from oil shale. Modified in-situ technology involves large underground chambers, or retorts, which are formed by mining out a minimal volume of rock to allow explosive expansion of the surrounding rock into tile mined void volumes. The resulting rubblized retort volume must contain a fairly uniform particle size distribution and void distribution to permit maximum oil recovery during subsequent in-situ processing operations. The more uniform the rubblized volume of particles, the more oil recovery obtained during processing. The processing involves first igniting the top of the retort and then. injecting air into the top of the retort to drive the combustion front downward through the entire rubblized volume. The oil is continuously collected at the bottom of the retort during the processing.

Jan 1, 1981