Search Documents

By C. Carrasco

"Over the last 30 years the average grade of mined ore bodies has significantly decreased while the proportion of waste removal has in many cases more than doubled. This has been identified as prime reason of a major increase in energy consumption and decrease in productivity across mining operation. Metal coarse preconcentration of ROM feed grades by size rejects low grade gangue/waste material in the size range of 10-100 mm prior to grinding, typically before primary crushing. This relies on propensity of metal to preferentially deport in the fine size fractions after breakage. Metal preconcentration by size has the potential to increase energy efficiency and therefore improve mining productivity on unit of metal basis. Results of an extensive belt cut sampling campaign conducted at a major Australian Au-Cu mine operation show that for some samples between 90% of Au and 80% of Cu is in 40% of the mass at -50 mm fraction. This indicates that low grade coarse material can be removed from the circuit, doubling feed grade at half of the tonnage and therefore improve energy efficiency per unit metal produced. This response, however presents significant variability in the same order as other processing attributes such as impact hardness and flotation recovery. This has led to development of geometallurgical laboratory tests using blast hole chips and drill core facilitating mapping and population of coarse metal preconcentration signatures in long term resources and short term production models. Preferential Cu deportment by size at drilling scale can be recognised, however scales up factors are required to transform laboratory results to production responses. At 50 % of mass the drilling products underestimate the belt cut responses by 20-30 %. Bulk sampling campaign with blast hole and drill core samples spatially related was also conducted to investigate in more detail the difference between production scale and drilling scale preconcentration responses."

Jan 1, 2014

By N. J. Bolin

The Aitik copper mine is located in the north of Sweden and the concentrator at the mine started its operation in 1968 with a capacity of 2 Mton ore per year. Since then the operation has expanded several times, and today the capacity is 18 Mton ore per year. A new expansion plan was investigated in 2005, however the building of a new concentrator was found to be a better solution, giving a lower cost, a longer lifetime and more concentrates to the smelter at the coast. Several choices have been evaluated regarding the location of the concentrator?s crushing, grinding, dewatering, process control and water systems. The energy cost comparison has been an important factor when evaluating the various choices. The single most important decision has been in choosing the grinding system. Once again the fully autogenous grinding system, favoured by Boliden, has proven to be the best solution. The location of the mill, high and near the tailing pond, gives lower transportation costs for the ore and tailings, compared to other locations. A new water system will lower the pumping cost, give better control of water circulation to the plant and create fewer problems with permafrost in the tailings disposal area. Molybdenum recovery will be installed in the new plant using a separate circuit. A gold leaching plant was also investigated. Gold leaching is planned for the pyrite concentrate from the chalcopyrite/pyrite separation and the concentrate from the desulphurisation circuit that will be installed on the bulk flotation tailings.

Jan 1, 2014

By Chris A. Fleming

"The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative.There is arguably an even more compelling reason for mining companies to consider cyanide recycling. With the growing storm of negative public opinion that the use of cyanide in the mining industry is attracting - following several highly publicized spills over the last couple of years - the time has come for the gold industry to demonstrate environmental diligence and stewardship in the use of this commodity that is so vital for their industry. There is no doubt that the widespread implementation of cyanide recycling will reduce the impact of the cyanidation process on the environment, both by reducing the risk of spills (with less cyanide being transported from manufacturing plants to gold mines), and by reducing the loading of toxic and nontoxic metals and ions in the tailings.This paper briefly discusses the pros and cons of the different processes that are available for the treatment of gold plant tailings to regenerate and recovery cyanide for recycling, and presents a techno-economic argument for the incorporation of this technology into many gold plant flowsheets today."

Jan 1, 2003

By E. V. Manlapig, M. C. Harris

"The complexity of the flotation process has made the identification of an appropriate model structure, for use in the prediction of flotation circuit performance, far from obvious. Work performed under the auspices of the AMIRA P9 flotation program has indicated that the metallurgical performance achieved from a flotation cell arises from the interaction of two essentially independent property classes, namely the cell operating conditions and the properties of the cell feed stream. These observations have led to the development of a model structure that associates a constant set of flotation parameters to the streams of the circuit, which are transformed into a flotation response depending on the operating conditions within the flotation cell.A variety of alternative model structures exist within the literature which do not make this distinction between cell and stream flotation properties, and many of these models are in widespread use for flotation optimisation and design studies, both in industry and academia.In this paper, data collected from an industrial flotation circuit is used to derive the parameters associated with two different types of flotation models. Simulations performed using these models demonstrate the need to differentiate between cell and feed properties. A model that does not differentiate between these two properties fails to successfully predict the metallurgical performance of a flotation circuit after a disturbance."

Jan 1, 2003

By A. Lane

Africa is ripe with opportunity for the mining industry. The continent has large, and relatively unexplored mineral deposits, and recent high economic growth rates have meaningfully improved the political, economic, and infrastructural environments. However, these opportunities are accompanied by significant risks, including resource nationalism, uncertain regulation, corruption, and continuing political instability (up to and including war). Forward-looking companies actively manage these risks by creating a sense of shared purpose with the countries and communities that own the resources, using tools such as stakeholder analysis, local narratives, scenario planning, and constituency engagement. They also measure socio-economic impact to insure the creation and demonstration of shared value.

Sep 1, 2012

By Paul Gottlieb

This paper reviews the status of automated applied mineralogy today and describes the history and fundamental theoretical and practical bases underpinning the development of automated systems. Details are given of the technical challenges that were faced in creating the new technology and in applying it to a range of applications. In recent years, automated mineralogy has become established as an essential enabling technology for the reliable acquisition of statistically sound comprehensive mineralogical and metallurgical data. This has had a revolutionary effect on the industrial use of such data in the study of geology, mining and mineral processing. Previously, using manual methods, it was not feasible to attempt this work because the large data sets required could not be assembled in a realistic timescale. There was a reliance on individual expert mineralogists and this was not scalable. The speed, reliability, detail and repeatability of the modern automated measurements has now made this type of analysis routine. Automated Applied Mineralogy has come of age! More than 100 systems have been installed around the World. Automated mineralogical analysers such as QEMSCAN® were originally developed as diagnostic metallurgical tools to improve mineral processing plants using samples drawn from plant surveys, bench and pilot-scale tests. They were used mainly for the assessment and auditing of size fractions of mill products, such as concentrates and tails. Subsequently, they began to be used for concentrator design and optimisation where ore characterisation was used to help understand the relationship between the feed ore and its subsequent behaviour in the plant. They are now widely used to measure exploration cores and drill chips from drilling programs to predict eventual metallurgical performance. Ore samples can be classified into metallurgical, as well as geological types, by combining mineralogical features in the ores with metallurgical properties related to grade control, separation, comminution, flotation and leaching behaviour. Three-dimensional block models of ore deposits are now being created based on processing response in addition to geological and mining properties. The development of automated systems began in Australia, the United Kingdom and Canada in the late 1970s and early 1980s. There were many technical challenges. Mathematical theories of randomness, sampling theory, image analysis and stereology were developed to ensure sample representivity so that meaningful information could be obtained. Sample preparation, presentation and measurement methods were developed to ensure that the random sampling was preserved during the measurements. Methods of automatic measurement and mineral identification evolved from the use of electron microscopes, fitted with backscattered electron brightness and energy dispersive X-ray detectors. Operational procedures were required to ensure that these instruments could accommodate a large number of samples and operate unattended for long periods of time. The new technology was progressively applied to a range of commodities and applications and new analysis methods, such as liberation measurement, were needed for metallurgical interpretation of mineralogical data.

Jan 1, 2014

By Maurício Torem, Gabriela Huaman, Antonio Merma

The purpose of this review paper is to succinctly present the most significant works related to Mineral Processing and Environmental Bioremediation and developed by the Mineral and Environmental Technology Group (METG) of the Materials Engineering Department of the Pontifical Catholic University of Rio de Janeiro (PUC-Rio). In mineral processing it was emphasized the use of the Rhodococcus opacus bacteria as a bioreagent in the bioflotation of some mineral samples (magnesite, calcite, hematite, quartz and apatite). The adsorption of the bacterial cells on the mineral surface can be due to specific and/or non-specific interactions, which will depend on several factors, as their surface charge and hydrophobic character. The zeta potential evaluation of the mineral particles before and after interaction with the R. opacus cells showed that the biomass modified the zeta potential profiles of the minerals, which confirm the adsorption of bacterial cells on the mineral surface. Moreover, the bacterial cells adsorbed caused a change in the mineral flotability which is related to a change in their hydrophobic character, thus, the mineral bioflotability was found to be dependent on the pH and the bacterial concentration. On the other hand, the environmental bioremetiation assessed the biosorption potential of three metal ions (lead, copper, and cobalt) by four different biomass Streptomyces lunalinharesii, Rhodococcus opacus, Rhodococcus ruber and coconut shell powder. For this purpose, biosorption process was characterized under different operating conditions such as initial pH and biosorbent dosage. The Freundlich and Langmuir isotherm models were applied to the equilibrium data obtained at different concentration.

Jan 1, 2014

By A. L. Hinde

The steady-state and dynamic behaviour of semi-autogenous grinding (SAG) mills are arguably best described using a population model that caters for the breakage kinetics and the material trans-port of rock and pulp inside the mill. Breakage kinetics are usually expressed in terms of a specific breakage rate function and a separate primary breakage distribution function. Material transport usually invokes the concept of a specific discharge rate function. Unfortunately, the breakage rate and breakage distribution functions for SAG mills are very difficult to estimate uniquely from plant data alone. Simplifying assumptions must be made to over-come this problem, which leads to many unresolved dilemmas with regard to whether or not the de-rived functions are accurate, precise, and reflect reality. For example, it is sometimes assumed that the breakage distribution function for a SAG mill treating run-of-mine ore can be derived from laboratory dropweight and tumbling tests on small rocks in narrow size ranges. Such tests hardly reflect the environmental conditions likely to be encountered in a pilot or production SAG mill where there is a wide spectrum of particle sizes. It is shown that the dilemmas associated with standard population balance models (models that utilise separate breakage rate and breakage distribution functions) can be overcome by expressing breakage behaviour inside a SAG mill in terms of a single function. This function is an energy-based cumulative breakage rate function defined as the fractional rate at which particles and rocks coarser than a given size break to below that size per unit specific energy input. A model for SAG milling is formulated, which invokes the concept of a cumulative breakage rate function. Comparisons are made between the mathematical structure of this ?simple model? and standard population balance models. Perhaps the most attractive feature of the ?simple model? is that the cumulative breakage rate function can be uniquely estimated from measurements of size distributions and mass flows of the feed and discharge streams together with the size distribution and holdup mass of the mill charge. Such measurement can easily be made at pilot scale. It is concluded that this simplified approach to SAG milling may turn out to be the quickest way to fully describe and quantify the performance of these very complex mills.

Jan 1, 2014

By Herman D. Mendoza

A rapid recovery/recycling process was introduced utilizing the surface-chemical properties of finely dispersed mercury and alumina (Al2O3) fibers in aqueous environment. The conventional method of amalgamation or .ball milling. involves the mixing of a substantial amount of mercury to collect free gold during the grinding stage. In effect, a portion of the mercury is transformed into minute droplets that readily float and disperse in the amalgamation effluent. The fine droplets of mercury in the dispersion readily attached onto the positively charged macroscopic alumina fibers (i.e. = pH 9.8) at conditions pH 3 to 10. When an effluent from settling procedure after an amalgamation-grinding stage is passed through a column-bed packed with alumina fibers, maximum collection of negatively charged finely dispersed mercury occurred at pH 3 to 6. The collection/attachment efficiency was 99.5%. The collected droplets of mercury, which are left in the column-bed of alumina fibers, were subsequently rinsed with alkaline solution at pH 10 to 11.5. At these conditions, both mercury and alumina fibers carry negative surface potentials and resulted in the partial detachment of mercury from the alumina fibers. The detachment efficiency was only 30-35%. The attachment/detachment mechanisms in this study were analyzed using the DLVO theory.

Jan 1, 2003

By Tracy Shimmield, Philip Samar

"Metals have been mined as ores since pre-history but metal production has increased dramatically in modern times driven by expanding Global GDP. Metal ore mining produces large amounts of waste rock and mine tailings. Mine tailings are the wastes produced after extracting the desired metal from the ore. There are several ways of dealing with this waste, and Ritcey (2005) identifies the following possibilities, land-based storage, backfill to the mine, deep lake disposal and marine disposal. In Papua New Guinea (PNG), both Misima and Lihir Mines adopted the marine disposal option, releasing tailings through a submerged pipe onto the sea floor. This special case is referred to as Deep Sea Tailings Placement (DSTP) in which the tailings deposition is sufficiently deep as to be below the euphotic zone. The most important aspect of deep sea tailings placement is that the tailings are deposited at great depth where exchanges between the seabed and the surface layers are small. The first quantitative multidisciplinary study of tailings impact on the deep sea was carried out from 2006 to 2010 in Papua New Guinea. The physical, chemical and biological work carried out has placed PNG at the forefront of research into the assessment and management of deep-sea environmental impacts related to mining in PNG. The study has provided data which has led to a better understanding of the ecological and geochemical processes in deep water that accompany DSTP in PNG and provided baseline data on deep-sea ecosystems in a scientifically poorly known tropical ocean. Additionally, guidelines on best practice for DSTP have been developed Here we present geochemical data obtained from sediment samples from the marine environment surrounding Lihir and Misima Islands."

Jan 1, 2014

By V. F. Petrov

Today, sodium cyanide is extensively used for extracting gold, however it is highly toxic to the environment if not managed properly. This paper discusses the key challenges presented to gold operations in efforts to come into alignment with the Russian environmental regulations and suggests solutions to overcome these challenges. It is a fact that the major environmental threat cyanide poses to water sources. Therefore, natural water sources should be well protected from the adverse effect of cyanides used in hydrometallurgical processes. For this, the following site procedures and facilities are practiced: in-site and external water recycling systems, reclaim water treatment if required and tailings ponds with water impermeable screens (tailings ponds with controlled leakage). Cost comparison analysis of cyanide destruction methods was carried out. It was revealed that the aldehyde treatment method developed by Irgiredmet JSC demonstrated the best economics. Cyanide emissions are treated by mass-manufactured packed and membrane devices which allow to keep cyanides at the acceptable limiting values established by environmental regulatory agencies.

Jan 1, 2014

By N. S. Phala

Declining gold grades, mineralogical complexity of ore bodies, increasing input costs, more stringent conditions in the licenses to operate, and uncertain gold price dynamics combine to exert significant ongoing pressure on margins of gold producers. Innovative approaches of extracting the metal from its ores are required to realize value from existing and future assets. In a conventional gold processing plant, size reduction of mined ore to produce floatable or leachable product is a significant cost contributor. A step change in cost reduction will be attained if radically energy efficient grinding approaches can be developed, replacing tumbling mills. In the path towards that goal, some quick wins are possible through waste rejection before grinding, and pre-treatment of mill feed to reduce grinding energy demands. Gold locked in complex mineralizations puts pressure on margins by increasing cost per oz (typically high $/t and low metal recoveries) in the hydrometallurgical steps. Gold miners are primarily price takers. The current narrow range of gold uses (predominantly investment and jewellery) is not an entirely desirable state. Some diversification into commercial uses would potentially be a price stabilizer. In this paper, promising research directions, some not always fully explored in the gold metallurgy research space, are highlighted to stimulate radical innovation for substantial value enhancements. The author strongly believes a shift from a traditionally conservative and incremental innovation approach to a more aggressive one, across all aspects of the gold metallurgy value stream (processes to products), is what the industry needs. Keywords: gold metallurgy value stream, thiobaccilus ferroxidants, HPGR

Sep 1, 2012

By M. Karamoozian

Modelling and optimisation of the power draw of large SAG mills are important due to the large power draw which modern mills require (5~10 MW). The cost of grinding is the single biggest cost within the entire process of mineral processing. Traditionally, modelling of the mill power draw has been done using empirical models. Although these models are reliable, they cannot model mills and operating conditions, which are not within the model database boundaries. Also, due to their static nature, the impact of the changing conditions on the power draw, within the mill, cannot be deter-mined using such models. Despite advances in computing power, on-line modelling of large plant scale mills could be a time consuming task. On the other hand, using on-line parameters for model-ling, result in more reliable control of SAG mill without performing any more costly tests. In this paper, SAG mill power draw is modelled using neural network approach. Six inputs, namely: solid percent, two bearing pressures, noise, recycle and feed rate were used to model the power draw. The produced model shows an acceptable correlation coefficient, R2 =0.9623.

Jan 1, 2014

Much has been published in recent years on the challenges facing the engineer of the 21st century and the consequent challenges facing the education providers and industry. The world is changing rapidly on the social, economic, political, technical and environmental fronts and our metallurgists/mineral processing engineers of the future will arguably need to have a different set of skills than those which were traditionally regarded as adequate during the latter half of the 20th century. This paper attempts to explore some of these issues and their ramifications.

Jan 1, 2014

As a kind of collector, Xanthates are generally used to make sulfide minerals hydrophobic in flotation process. Xanthate adsorption on a galena surface has been widely studied experimentally. In this paper, DFT methods were employed to investigate the local adsorption interactions about the collectors,such as ethyl xanthate (CH3CH2OCS2?, EO) and ethyl trithiocarbonate (CH3CH2SCS2?, ES), absorbing on two different PbS clusters. From the results, it can be easily found that, on the edge or at the apex, both collectors, with two S atoms bidentate coordinating on the clusters, have surprising interaction energies, while on the surface, its interaction is relatively weak in the form of monodentate ligand. NBO analysis results reveal that there is at least a covalence bond with sulfur atom about 10% and lead atom about 90% when the absorbed lead is on the lattice edge or at apex, but, if the absorbed lead is on the lattice surface, no covalence band would be found. Meanwhile, the S-Pb bond, formed by the absorbed Xanthate and galena lattice, seems to have much more covalence characteristic than that formed in the PbS lattice inner. Furthermore, those data also imply that the difference of the collecting effect between the EO and the ES may be not notable, because of the similar distance and the interaction energy for the same interaction mode.

Jan 1, 2014

Compressive crushing is applied in crushing plants used in mineral, mining, and aggregate in-dustry for fragmentation of rock materials. From a global perspective, the total volume of crushed rock is massive and corresponds to several billion tons. All societies have to fulfil a daily need of rock material products and its derivatives such as metals and minerals. The business for metals and minerals is global while the aggregates production is mainly a local industry. This paper presents a broader overview of optimisation with respect to product yield, use of natural resources and energy consumption. High level plant optimisation of compressive crushing plants is covered as well as real-time optimisation and optimisation of single production units. Each of three optimisation areas are presented and a discussion around how these three areas will be able to communicate with each other is given. Several models, e.g. process performance behav-iour with respect to wear, as well as fitness functions can be common for all three areas. Well-defined and representative fitness functions are of the utmost importance in order to assure that the optimisation results reflect the production targets. It is concluded that great benefits can be achieved by linking together different areas of optimisa-tion. The future for compressing crushing lies, without a doubt, in tailored processes both with re-spect to machines optimised for each customer, plant parameters and operation routines as well as an on-line adjustment, which takes into account current information and control possibilities.

Jan 1, 2014

By Y. M. Zhu, G. C. Gong

"The influences of citric acid (CA) on the flotation behavior of cassiterite using styrene phosphonic acid (SPA) as the collector were studied via single mineral flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations in this paper. The results of single mineral flotation tests revealed under the conditions that pH=4 and the dosage of SPA 100 mg/L, the recovery of cassiterite reached 76.78%. The addition of 20 mg/L AC decreased the recovery by 12.42% at pH=4. Contact angle measurements demonstrated the adsorption of CA prior to SPA made the cassiterite more hydrophilic. The results of zeta potential determinations and solution chemistry calculations indicated the chemisorption of C6H7O7- and C6H6O72- filled parts of the Sn site on cassiterite surface and prevented the SPA from getting adsorbed. The hydrophilic effect of AC was stronger than the hydrophobic effect of SPA and the flotation of cassiterite was crippled. INTRODUCTION Tin is an important metal which is widely used in medical instruments, marine engineering materials, electronic and electrical devices, welding, weapon manufacturing and organotin compounds industries (Angadi et al., 2015). Cassiterite is the only mineral from which the tin can be extracted, thus it is of great importance to efficiently exploit the cassiterite mineral. Flotation is an indispensable method for the recovery of cassiterite (Li et al., 2015). However, cassiterite is usually in association with many other gangue minerals which are of similar floatability, such as quartz, calcite, fluorite, iron oxide, wolframite, scheelite and tourmaline (Sreevinas, 1997). So some modifiers are necessary in the cassiterite flotation process. The amounts of the modifiers used in the flotation must be judicious and the overmuch modifiers may cripple the recovery of cassiterite (Parsonage et al., 1987). Nevertheless, the research about the effects of the modifiers on the flotation behavior of cassiterite has been rarely reported. In this paper, the influences of citric acid (CA) on the flotation of cassiterite using styrene phosphonic acid (SPA) as the collector were investigated by flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations."

Jan 1, 2018

By Dominic Howarth, Diana Drinkwater, Don McKee

"The pressures on mining and minerals education at the tertiary level are well known. Within Australia, for example, the number of undergraduate mining engineering courses with 30 or more students in each year has reduced to three (University of Queensland, University of New South Wales and Curtin University). Similar declines in both student numbers and participating institutions are evident in many other parts of the world, and notably in USA and most countries in Europe.An in depth study of the Australian sector was conducted in 1997/1998, resulting in the Back from the Brink report (Carter 1998). The Australian situation was summarised as follows.Australia’s minerals education system, in its current form, is fragile and is in no position to seize the opportunity (i.e. world leadership in minerals education) and is more likely to succumb to the threat.Current trends include:- an acute shortage of talented academic staff, as a result of University remuneration packages having become hopelessly uncompetitive with those in the minerals industry;- small student populations and high relative costs, making mineral specific courses vulnerable to closures, when Universities are under extreme cost pressures; this situation will be exacerbated if enrolments drop in response to, say, a cyclical down turn in the industry; and- under-resourcing of minerals departments because of their comparatively small size, making these departments incapable of delivering top class teaching in all aspects of their courses, despite being excellent in some areas.Most of the Australian issues identified above have direct parallels in other countries.The most common response of institutions to the threats is to seek strength, and in some cases survival, through various forms of linkages and networks. A number of these associations, which are frequently defensive in nature, are outlined in the paper."

Jan 1, 2003

By Eberhard Gock

The worldwide implementation of corrosion protection of low alloyed automotive metal sheets by zinc coating has led to supply shortages of zinc free non-alloyed steel scrap in the foundry industry. In a collaboration project, partly financed by the German government, with partners from the automotive industry, zinc metallurgy, scrap trading, foundry industry, and plant construction, a new acid-based pre-dezincification process has been developed, and a pilot plant with throughput of about 100 t/d has been put into operation at the Clausthal Umwelt-Institut GmbH (CUTEC) together with the Clausthal University of Technology in Germany. During the treatment process, acid from a zinc metallurgical plant will be supplied, which can be recycled to the primary zinc extraction process after raising the zinc concentration to more than 130 g/L zinc. This way, the separation of small amounts of iron by precipitation and the electrolytic zinc winning are outsourced and, as a result, the pre-dezincification process runs waste-free. In Germany, the amount of zinc coated ?new scrap? is approx. 3 million t per year with a zinc content of approximately 60,000 t per year. The possible additional incomes for the dezincified steel scrap are in the order of ?40 to ?50 per ton of scrap, the gained zinc content during the acid dezincification defrays the costs of the process, if the throughput is more than 700 t/d. In comparison to conventional dezincification during the electro arc furnace process followed by upgrading in a rotary kiln (Waelz process), the acid dezincification process running at a maximum of 50°C will cut the energy costs by up to 74% and the CO2 emission by up to 88%. In fact, a demonstration plant is being designed right now and will be installed for processing a part of the zinc coated metal scrap from the Volkswagen AG in Wolfsburg, Germany. Keywords: steel scrap, zinc-coated steel, dezincification methods, acid

Sep 1, 2012

By Moris Fresko, Julia Sun, Charles C. Golembewski, Vytas Svalbonas

"A history of mill strain gaging at Metso is presented. The output of these strain-gaging programs is compared with calculated stress ranges from different finite element solutions. These comparisons expose the amount of approximation that exists in the analytical solutions, starting from geometry, and material properties, and ending with different forms of internal load models. The influence of strain gaging results on mill design and analysis practices is also discussed. While these instrumentation programs are valuable in identifying areas of high stress in mills, and locations of stress concentration factors, they are by no means extensive or comprehensive enough to verify general internal load models. The vast majority of the programs were aimed at getting additional data about potential failure points, rather than describing overall mill stress behavior. This is especially true since the more recent gaging programs have not included the difficult task of gaging the mill rotating structure interior. This paper tries to avoid the novice path of leaping to general conclusions on the basis of insufficient data."

Jan 1, 2014