Search Documents

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks, R. L. Sachdeva

"A combined shaft-electric furnace for the smelting of ores and the melting of metallized iron pellets is being developed. The materials are preheated, and in some cases pre-reduced, in the shaft before being transferred to the electric furnace, where melting or smelting is completed. It has been demonstrated that this combination of equipment will enable much of the relatively expensive electrical energy to be replaced by cheaper energy in the form of oil or natural gas, and preliminary experiments indicate that the total energy requirements for a melting or smelting operation are significantly reduced. Projections based on results obtained from the preliminary experiments indicate that further improvements will be possible when certain modifications to the equipment are completed."

Jan 1, 1968

By E. S. Moore

In order that a logical conclusion may be reached regarding the possible occurrence of commercial iron deposits in Canada it is necessary to consider some important producers found elsewhere on this continent. A study of such deposits reveals the fact tl:~at a number of distinct types are producing large tonnages of ore. These types may be classified according to origin and occurrence as follows: (1) Bedded sedimentary deposits. (2) Contact metamorphic deposits. (3) Residual ores. (4) Lenses in metamorphic rocks and m some cases of uncertain origin. In addition to the types listed there are other deposits which have contained or do contain considerable ore and they either have not been worked on a large scale or they have been nearly exhausted. These include the following types: (1) Magmatic segregations. These are mostly titaniferous magnetites. (2) Dikes of magnetite of igneous origin. (3) Bog and lake ores in glacial drift. (4) Black sand placers.

Jan 1, 1925

By Yin Guangzhi, Song Zhenlong, Li Minghui, Li Wenpu, Deng Bozhi

"Darcy's law is widely used to describe the oil and gas flow characteristics in the multi-pore media reservoir. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the high-velocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore. The gas flow velocities in coal in different deformation stage under different gas pressure gradient were tested and the relationships between gas flow velocity and gas pressure gradient were discussed, which can help us to investigate the transformation conditions of gas linear flow and gas nonlinear flow in coal. The results showed that the gas flow in the coal under low effective stress environment can be described by Darcy's law. The low-velocity non-Darcy flow of gas gradually occurred and the start-up pressure gradient increased in the coal as the effective stress increased. The low-velocity non-Darcy flow of gas also occurred in the coal at the yield deformation stage, however, the start-up pressure gradient decreased as the effective stress increased in this stage. In post-peak stage, the highvelocity non-Darcy flow of gas occurred in the coal under low effective stress environment. The gas flow in the coal gradually returned to be Darcy flow as the effective stress increased. The mechanism of the phenomenon is discussed based on the experimental results. The research results can be used to guide well test analysis and prediction of oil-gas production. INTRODUCTIONThe oil and gas flow in original multi-pore media reservoir are usually regarded as steady and linear processes and can be described by Darcy’s law. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the highvelocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore or workface. The gas flow in the multi-pore media even may be unsteady under some conditions such as gas emission and outburst.The phenomenon of underground water low-velocity flow in clays was deviated from Darcy’s law was found in the end of the nineteenth century (King, 1898). The deviation from Darcy’s law was later reported and investigated more (Swartzendruber, 1962; Miller and Low, 1963). These researches revealed that the start-up pressure gradient exists under low permeability conditions. Klinkenberg (1941) proposed that the permeability constant as determined with gases is dependent upon the property of the gas, and is a linear function of the reciprocal mean pressure. This effect can be explained by taking into account the phenomena of slip, which are related closely to the mean free paths of the gas molecules."

Jan 1, 2015

By Yulin Zhou, WenFeng Li, Wen Chen

"In this article, with the help of the X-ray photoelectron Spectroscopy (XPS), a modern test method, all the characteristics of the chlorite,and adsorption collector A6 on the surface of chlorite have been studied. There exist abundant carboxylic C-O and C=O structures in the Carbon XPS atlas with strong adhesive ability after the reaction between new collector A6 and chlorite, which indicates that the ring structure and ether-base functional groups can strengthen the reaction between collector A6 molecule and chlorite surface. The results of XPS analysis indicate that the photoelectron spectroscopy peaks of Mg2p and Al2p moved towards low energy after collector A6 absorbed on chlorite surface, which indicates that chemical bonding through electron cloud transfer happened between collector A6 and Mg, Al ions of chlorite surface. The chemical reaction promoted the adsorption of A6 on chlorite surface and eventually improved the ability of A6 to float and collect chlorite.INTRODUCTIONThere are a large amount of iron-bearing silicate minerals such as chlorite in different types of gangue minerals in iron ore from different areas besides quartz (Yingyong et al, 2012; Qiang et al, 2009). There always exist Mg2+, Al3+ Fe3+ and other metallic ions due the isomorphic replacement among the irons of this kind of minerals. The dissolution often occurs on the surface of minerals with abundant metallic ions during grinding process, and some ions are exposed on the surface, such as Mg2+, Fe3+, Al3+, Si4+, which can increase the surface electrical behaviour of iron-bearing silicate minerals (Wanzhong & Chuanyao, 2002; Yuping et al., 2007), making it easy for the surface to react preferentially with the depressants such as causticizing starch which making it impossible for the surface to reach with conventional anionic fatty acid collector (Mowla et al, 2008). Thus, the beneficiation efficiency is dramatically decreased and the improvement of concentrate grade becomes very difficult. The conventional aliphatic acid collector has some defects such as poor selectivity, poor low temperature resistance, sensitive to water hardness, etc. Thus, the addition of synergist (Liu, & Yu, 2015) or other compound reagents (Zhou et al, 2015) can promote the adsorption of reagents to mineral surface, and improve the collecting capacity and selectivity of aliphatic acid collector to minerals. The addition of polar group to nonpolar group in aliphatic acid can improve the water solubility, dispensability and hard water resistance (Tian et al, 2013). The nitrogen atoms in amid ate aliphatic acid collector can adsorb on mineral surface by itself and supply coordinate electron which can form chelating keys to improve the collecting capacity of collector. There exist coordinate electron in oxygen atoms of ether acid collector, which, along with the oxygen on carboxyl compose chelate with metal (Luo et al, 2015). There are also exist some opinions that the ether acid can arrange into similar crown ether structure which can absorb on mineral surface. A new alicyclic unsaturated ether acid compounds collector A6 is adopted in this paper, the structural formula is listed in Figure 1. The A6 has a strong collecting ability to chlorite with strong water solubility and low temperature resistance."

Jan 1, 2016

By Yu Chen, Charlie C. Li

The application of rock bolts for the stabilisation of underground openings needs a good understanding of the response of the bolts during rock excavation. The pull-and-shear performance of two types of rock bolts—that is, the fully encapsulated rebar and the D-Bolt—has been studied both experimentally and numerically. The rock bolts were tested under a pull-and-shear load at five displacing angles (i.e., 0°, 20°, 40°, 60°, and 90°), and at the same time, the strains on the bolts were monitored during testing. The two types of rock bolts have similar loading capacities, while the loading angle has obvious influence on the deformation capacity of the D-Bolt. The ultimate total displacement of the D-Bolt decreases from 140 mm under pure pull loading to 70 mm under shearing. The displacement capacity of the rebar is not significantly influenced by the loading angle but remains at a quite low level from 29 to 53 mm. The D-Bolt yielded in a longer section the rebar bolt under pure shear. A trilinear material model was used to simulate the strain hardening behaviour of the bolt steels in the numerical code FLAC3D. The numerical results show that the axial load in the bolt decreases exponentially with the distance from the loading position for the rebar bolts, but it remains constant in the bolt sections between the anchor positions for the D-Bolts. When the bolt is subjected to a lateral load, shear stresses are created on the D-Bolt surface within a short distance from the loading position.

Jan 1, 2015

By George W. Bain

Mr. Geo. W. Bain: Dr. H. C. Cooke's discussion of 'The Geology and Mineral Deposits of the Harricanaw and Bell River Basins' possesses many of the elements of a good political address; perhaps his long residence in Ottawa has some bearing upon his method of discussing geological work. The three essential parts of the address are all included. First, the plank - "Contributed discussion on the Geology and Mineral Deposits of the Harricanaw and Bell River Basins"; second, the personal attack upon the opponent, to show antipathy to the opponent as well as to his ideas; and third, controversion of a number of statements, which have been made to appear as planks of the opponents platform, even statements and work which are in no way connected with one under discussion. In the following pages, I will confine my attention to a defense of my work in the Harricanaw and Bell River basins, leaving discussion of the other areas mentioned by Dr. Cooke until results of the re-surveys are published. It is intimated that it was impossible to make a geological examination of an area of 1,600 sq. miles on a scale of four miles to the inch (base map supplied) in three and a half months, because "the area is accessible only from the railway along the northern edge together with a few roads close to it, and from rather wide separated streams?. There is one way, known to most geologists, whereby a place can be reached other than by railway coach or motor boat, and that the oldest of all -- walking. Most of the region was reached in this fashion. The boundaries of all the 18 townships included in the map are surveyed, nine are divided into lots, and the north-south and east-west centre lines of most of the others are surveyed and have mile-posts placed.

Jan 1, 1927

"In the present study, the reduction behavior of composite pellets comprising of iron oxide, synthetic graphite and slags were investigated in a laboratory-scale horizontal tube furnace. Two different types of slags indicating silicate base and aluminate base slags were chosen to examine the effect of slag chemistry on the reduction behavior of pellets. Slag composition of binding materials has influences on the reactions occurring in composite pellets during direct reduction. In-situ high temperature visualization approach was used to observe the slag / iron / carbon interactions at 1773K (1500°C). The off-gases were measured by means of infrared analyzer to determine the reaction rates of the pellets. Different physical appearances during the in situ reaction inferred a strong correlation between the slag composition and internal reactions. In addition, compression tests were conducted to examine physical strength of the pellets. This investigation was carried out to establish feasibility of physical property control of pellets by selecting optimum slag compositions of binding materials INTRODUCTIONCurrently, most of the iron ore mines have facilities that make an ore more usable for the blast furnace operation by improving its physical properties (e.g. pelletizing and sintering). However, during the process, a large amount of fuel is supplied to indurate materials which consequently deteriorate energy efficiency and produce more CO2 emission. Along with increased interests, direct reduced iron (DRI) making process; simply without coke oven or sintering process, has opened the era of clean and environmental friendly iron making process. While some of the established DRI technologies such as Midrex and HYL were restricted to certain locations where natural gas is abundant, coal based technologies using Rotary Hearth Furnace (RHF) such as FASMET and ITmk3 have been developed with regardless of expensive fuel deposit. In addition to the direct use of pulverized non coking coal and fine iron ore, RHF process also has advantages of utilizing waste materials such as EAF dust, biomass and recycled plastics. Nevertheless, there are still many challenges in the coal utilizing technologies as the unprocessed coal and the waste materials contain huge volatiles and ashes. Although recent investigations on volatiles in a RHF process (Sohn and Fruehan, 2005, 2006) have indicated the benefits of coal in terms of iron oxide reduction and have shown feasibility of multi-layer process, carbon composite pellets still have disadvantages because of its weak mechanical bonding strength. As the mixed system with carbon and oxides generates intermediate gases (e.g. CO and CO2) between solid particles, it is difficult to keep its physical state without the help of binding materials. In this reason, industries have been tried to use various binding materials such as bentonite, kaolinite and Portland cement. However, they are still struggling to find out new materials that provide not only sufficient mechanical strength but also metallurgical properties, such as porosity, reducibility and swelling throughout the reduction reaction. Recently, Canadian researchers (Aota et al, 2006) observed enhanced mechanical strength of pellets by using high alumina cement as a binder and concluded that the method could be used to recycle EAF dust as well, but in depth mechanism of reinforced strength has not been concerned. Most of the ashes coming from binders formulate certain type of slag during the reduction process due to its incombustibility. Thus, observation and regulation of slag property is an essential for the control of carbon composite pellet. Yet, only a little thermodynamic consideration from the perspective of slag chemistry has been adapted in the iron and steel making industries as ash has been easily ignored for its tiny proportion. In this study, effect of CaO-SiO2- Al2O3 slag system on the reduction of iron oxide was investigated in terms of"

Jan 1, 2012

By Y. Jin, H. You, H. Pang, B. Lin

Successful application of steam assisted gravity drainage (SAGD) on the recovery of land facies ultra-heavy oil in Xinjiang oilfield depends largely on shortening the preheating period with the aid of the micro-fracturing technology, which is conducted through controlled water injection to a pair of horizontal wells to create homogenously distributed microcracks in the zone between the two wells. The numerical simulation of this mechanical process is yet to be investigated. Up to date, there has been research work on rock mechanics during the SAGD production period of marine deposited ultra-heavy oilsands, but the counterpart research on land facies ultra-heavy oilsands of Xinjiang oilfield is left undone. In this regard, this study is attempted to perform numerical simulation of the fracturing process on land facies unconsolidated oilsands. With this objective, the study first investigates geological and physical identification of the field collected cores, then carries out mechanical analysis on laboratory triaixal test results, based on which numerical simulation of the fractured zone is performed. The simulation is applied through a finite element platform adopting extended Drucker-Prager constitutive model, with the parameters determined by experimental work. It is verified that hydraulic fracturing of unconsolidated oilsands generates a microcrack feature in terms of a dilative zone instead of linear apertures. The extent to which the fractured zone propagates is visually demonstrated based on the magnitude distribution of equivalent plastic strain or volumetric dilation. Evaluation of the connection of injection and production wells can possibly be determined by the expansion of the saturated region around each well. Finally, the implications on the efficiency of hydraulic fracturing in stimulation of the pay zone are investigated.

Jan 1, 2015

By A. Djebara

Today, indoor air quality, especially in manufacturing industries, is of great interest due to the use of new processes and advanced materials such as those containing nanoparticles. Manufacturing processes generate aerosols (dry or wet) which can be detrimental to occupational health and safety and to the environment. Controlling metallic particle emissions during machining processes should limit their formation at the source, and thus minimize the risk of exposure; this at-source reduction requires the characterization of the particle emitted (size, nature, concentration, etc). The metrics normally used in characterizing fine and ultrafine particles include the mass concentration, the specific surface and the number concentration. Most of these metrics are affected by the size, the geometry and the density of the measured particles. Information about the form and the real size of the particles is thus very important. A procedure for collecting and characterizing fine and ultrafine metallic particles was developed and applied to the study of particles emission during the machining of aluminum alloys. It was found that metallic particles emitted during the machining of aluminum alloys are of various shapes and sizes, and this information must be taken into account when characterizing these particles.

Jan 1, 2011

This paper discusses three case studies conducted at Highland Valley Copper mine (HVC) that illustrate operational improvements and insights which resulted from using the McGill University gas dispersion sensors. In the first study, the superficial gas velocity (Jg) sensor was used to implement a gas profiling control strategy for the rougher, scavenger and first cleaner cells in the Cu/Mo separation circuit. The data showed a 40% reduction of down-the-bank Cu recovery at constant Mo recovery which resulted from operating the cells at the target profiles. In the second study, the bubble size analyzer was used to better understand two mechanisms of bubble formation in the two flotation columns that make up the final Mo cleaning stage: the conventional rubber-sleeve sparger and the Microcel(TM) system. The data showed a considerable reduction of bubble size in the Microcel column which resulted in a significant increase in concentrate quality (1-2% Mo absolute) and a dramatic (4-5 fold) increase in concentrate production rate compared to the typical operation. The estimated economic benefit resulting from the improved column flotation operation was an overall 4% increase in Mo circuit recovery. In the third study, real-time measurements obtained from the gas holdup and bulk density sensors were used to infer the pulp density (% solids) in a rougher cell of the bulk flotation circuit. Validation tests demonstrated that this approach provides reliable pulp density measurements. Although promising, more work is required before implementing this approach at HVC.

Jan 1, 2009

By H. S. Wilson

"The property owned by the Lamaque Mining Company comprises a group of forty-four claims and fractions occupying an area of about 2,458 acres, in west-central Bourlamaque township, Abitibi county, Quebec. It is on ,the outskirts of the towns of Bourlamaque and Val d'Or, about 70 miles east of Noranda, near the eastern end of the belt of greenstones of Keewatin and Timiskaming age that extends eastward through Kirkland Lake into northwestern Quebec, terminating in Haig and Jurie townships 40 miles to the east.The claims on which the orebodies occur were first staked in 1923; No. 3 vein was discovered the following year. The original discovery was made by R. Clark in 1923. This was a small quartz vein containing a pocket of coarse gold on the north side of a hill near the northwestern corner of block 3. It is said that all the gold was removed in one shot in blasting into the vein; elsewhere it was barren. A picket line was then run west along the strike of the vein, which occupied a narrow shear zone, and about 2,000 feet west, in prospecting on either side of the picket line, a large boulder of quartz and tourmaline containing visible gold was found. This led to more intensive prospecting by trenching in the vicinity with the result that the No. 3, or 'float' vein, about 250 feet north of the boulder, was found. Due to low ground this vein was exposed in only one trench. The only other important vein found on the surface was the No. 1, or H, vein, which was exposed in several places by stripping and trenching, but it did not carry appreciable amounts of gold."

Jan 1, 1954

By T. Xue

429 As part of Inco's S02 abatement project for its Sudbury operations, a weak acid treatment plant (W ATP) was commissioned at the Copper Cliff smelter in August of 2004 to treat the weak acid streams generated by the flash furnaces, the MK reactor and the fluidized bed roaster (FBR) gas cleaning plants. The W ATP process was developed by Inco Technical Services Limited (ITSL) by means of laboratory and mini-pilot plant programs. In the W ATP process, the feed solution containing arsenic, sulphur dioxide, iron and other impurities is treated by oxidation and neutralization to form a stable precipitate for disposal in Inco's tailings impoundment area. During the commissioning of the WATP, a team of operations, maintenance, engineering, project and R&D personnel was formed, and the designed capacity was achieved in less than a month. Since then, the W A TP has been operating smoothly and the impurities, specifically arsenic, in the Copper Cliff smelting process have been effectively removed.

Jan 1, 2006

By Kr. N. Karparov

Measurements made with high precision GPS landmarks and geotechnical radar Reutech MSR- 300 associated with the observed movements in the north face of Assarel Mine, where on a horizontal distance of 50 m, 2 groups of landmarks indicated different deformation behavior. Measurements are made in order to confirm the applicability of the radar system in regions of complex geotechnical conditions. The standard deviation of each landmark is used as an accuracy standard between the separate measurements of the deformation vectors made by the high-precision GPS system for each landmark. A very good correlation between the displacement vectors can be seen based on the measurements made with the high-precision GPS system and the measurements made by the radar system MSR-300. Geological, engineering geological and hydro-geological conditions of the area of concern are discussed in this paper. The measured deformations and the FLAC/SLOPE analysis show similar results. In the paper is discussed their local character and their sensitivity to other geotechnical and hydro geological conditions.

Aug 1, 2013

By G. Banini

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012

By W. D. Mulholland

"I ASSUME that any effort on my part to deal with the question of the importance of the mining industry is going to be largely an exercise in preaching to the converted, but there are one or two aspects that I'd like to particularly mention.The first is that, in terms of almost all factors, the mining industry is a very important industry in Canada. It is important in terms of employment in relation to the gross national product of Canada and it is particularly important in the international trade of Canada. So far from being insignificant domestically, it is also an extremely important factor in the international picture. That's an important point to bear in mind, because as we talk about all the other matters we never can lose sight of the fact that mining management always has to be conscious of its international competitive position. It is something that one forgets at one's peril, and to a somewhat greater extent than is true of many other industries, those managements have to compete in an international context for their markets, to some extent for their people for specialized skills and of course for finance. In the evolution of domestic policies it is a very, very perilous step to take to impair that competitive ability of the domestic mining industry."

Jan 1, 1972

By M. J. Latva-Kokko

This paper describes the behaviour of iron and the methods used for iron control in the nickel matte leaching process. OMG Harjavalta Nickel Oy processes approximately 10 000 t/y of iron, which enters the process with the nickel matte raw material. Iron dissolves and precipitates in several different stages of the leaching process. Compounds like ferric hydroxide, parabutlerite, goethite, hematite and jarosite are found. Iron removal is done within the leaching process, and this means that the dissolution of nickel sets the limiting conditions for iron precipitation. A leach residue consisting mainly of the iron precipitates is neutralized and stacked in the waste pond. When iron is precipitated from concentrated nickel sulphate solution, some nickel is lost by co-precipitation. Recent studies have shown that Ni-Fe ratios less than 1%, attributed to co-precipitation, can be obtained with jarosite precipitates, compared to 2-3% ratios typically found with hematite precipitates. Iron can be precipitated as jarosite under the optimal nickel leaching conditions by adding ammonium sulphate to the feed slurry of the autoclave.

Jan 1, 2006

By Grant S. Diamond

THE BIBLIOGRAPHY on the use of static electricity in mineral beneficiation consists largely of patents. Some references are found in mineral textbooks, but very little data on flow-sheets of commercial installations are known to the writer. As a matter of fact there have been relatively few successful commercial applications of importance. Johnson prepared and published a Table showing the polarity and static field intensity requirements of many minerals. There have been reports of successful beneficiation of rutile, zir-con, coal, potassium chloride, and phosphate rock. Otherwise, the field of success has been very limited. This may be due to three reasons: first, the mining industry has been averse to dry processes, be-cause of dust nuisances in dry crushing; second, the electrostatic processes used in the past apparently developed no substantial economic advantages; and third, because flotation or other . methods have proven successful on many minerals, the industry has not felt the need for a radically different process. In the feldspar industry there was ?an attempt at electrostatic beneficiation about twenty years ago which was based on the use of fluoride fuming of the pegmatite head feed, in order to make the mineral reactive in a static field. This process was originally said to be successful, but was discontinued because of corrosion damage to machinery. Another effort by use of a chemical additive such as an or-ganic hydroxyl compound has also been attempted. Neither of these processes is known to be in use today.

Jan 1, 1957

By F. W. Guernsey

Of all the elements, sulphur occupies a place by itself. It is mined in situ, in such quantities and of such purity that, as regards the tonnage produced, it is the first of any element on the list. Iron and coal the great tonnage producers, are combinations of elements, while sulphur is mined and marketed almost chemically pure. It is sold, in large quantities, commercially, calling for a purity of 99.5 per cent while for medicinal purposes, the Pharmacopoeia requires only 99 per cent. purity. It is a very common commodity, and like many common things is of extreme importance, in the progress of our civilization. The substance has been known from the earliest times, the word sulphur being derived from the Sanskrit Culvari", hence the Latin Sulphur. Commercially it is also called brimstone, this word being a derivative of the Anglo-Saxon Bryne Stane or burning stone. From our younger days, we have been more or less familiar with the mineral. On the spiritual side being threatened, if we did not behave ourselves, with an ultimate consumption in a lake of fire and brimstone, (which in moments of reflexion was not pleasant to contemplate) while our bodily ills were taken care of by inward applications as a spring medicine. In both instances, the effect required, was generally attained. Sulphur occurs in nature, both free and in the combined state, it being estimated that it forms, over one tenth of one per cent of the first ten miles of the earths surface. (I do not know who did the estimating and it is not guaranteed).

Jan 1, 1923

By Chris Harris, Kamal Adham

The use of HCl acid is gaining momentum among hydrometallurgical processes. However, the issue of environmentally efficient and economically viable ways to regenerate HCl acid (from various metal chloride intermediate products) remains a technology and operational challenge. The authors provide a state-of-technology review based on Hatch’s years of testing, design and commissioning experience with high-temperature units (fluid bed and spray roasters), plus the recent efforts in the area of low-temperature HCl regeneration.

Jan 1, 2014

By T. Urbancic, Eric von Lunen, G. Viegas, A. Baig

"The characterization of the failure process of induced fractures by hydraulic stimulation is fundamental to understanding the generation and evolution of the discrete fracture network within the reservoir. A more detailed analysis of the fracture mechanism can be a powerful tool for identifying fluid flow paths and proppant placement within the reservoir. For example, during the rupture process the energy release is partitioned into different physical processes for which the relative ratio is changed by the presence of fluids or rotations in the local stress field with relation to the frictional resistance in the fracture plane. Fractures occurring in the same host rock under the same stress conditions are expected to rupture similarly, independent of their size (self-similarity). Changes in the scaling relationships of fractures are indicative of a change in the failure process, host rock or in-situ stress. Correlation of failure process data with reservoir rock properties and the in-situ stress field will help identify regions within the reservoir with characteristic types of failures. Further correlation with hydrocarbon production data can be used to develop efficient treatment plans and production diagnostic tools.In this study we investigate the failure process of ~27,000 microseismic (M < -1) fractures induced during a hydraulic fracturing shale completion program in NE British Columbia, Canada by estimating static and dynamic source parameters, such as dynamic and static stress drop, radiated energy, seismic efficiency, moment tensor, fracture plane orientation, slip direction and rupture velocity. On average, the microseismic events have low radiated energy, low dynamic stress and low seismic efficiency, consistent with the obtained slow rupture velocities. Events fail in overshoot mode (slip weakening failure model), with fluids lubricating faults and decreasing friction resistance. Events occurring in deeper formations tend to have faster rupture velocities and are more efficient in radiating energy. Variations in rupture velocity tend to correlate with variation in depth, fault azimuth and elapsed time, reflecting a dominance of the local stress field over other factors.Further identification of spatial and temporal distribution of families of events with similar characteristic rupture behaviors, based on either rock formation, depth, source type, fracture plane orientation, stress drop, pad or proppant stage, may be used as a proxy for specific fracture network development and hydrocarbon production. This information may be used to determine reservoir properties, constrain reservoir geo-mechanical models with measured physical parameters, classify dynamic rupture processes for fracture models and improve fracture treatment designs. These will be the focus of future studies."

Jan 1, 2015