Search Documents

By S. Parent, J. -F. Lepage, S. Glover

"Goldcorp – Eleonore’s 7 000 tonnes per day gold mill was started up in October 2014 and achieved commercial production in April 2015. During the first year, operation has faced challenges from grinding, flotation, sulfide cyanidation and tailing filtration to achieve targeted throughput, availability and recovery.The optimization of non-sulfide tails filter cloth lifetime and filter press availability had the most significant impact on ramp-up of both mill throughput and availability. A change in steel ball addition size to the grinding circuit was made to meet the targeted p80 of 65 µm. Various optimization efforts were conducted on the flotation circuit, intended to recover all sulfide-bearing minerals. The goal is to attain the environmental target of 0.12% sulfur in flotation tails (to eliminate acid mine drainage or AMD), while an average of 0.31% sulfur was obtained over the first months of 2015. Collectors, frothers, activators and hydrodynamic parameters were tested to improve the circuit desulfurization efficiency. High sulfide reactivity in pre-oxidation and cyanidation severely impacted dissolved oxygen levels and cyanide consumption. Studies were undertaken to understand the effects of mineralogy, grind size and leach conditions on gold dissolution kinetics and cyanide consumption. Efforts were focused on pre-oxidation to restore dissolved oxygen levels as well as optimizing both lead nitrate addition and pre-oxidation time.INTRODUCTIONGoldcorp Eleonore’s mill commissioning started in September 2014. It was considered to operate the mill at 3 500 tpd during design, as the mine was planning to operate at this throughput for the first year. However, with the stockpile of ore and a higher throughput from the mine, the mill was able to run at higher tonnage than initially anticipated.While increasing tonnage, a few bottlenecks were discovered and overcome in areas such as filtration and cyanide destruction. There were also recovery issues which were addressed in areas such as grind and sulfide leach. This paper focusses on the first complete year of operation ending September 30th 2015. A process description and the flowsheet are presented below and it will then go into detail about operational, metallurgical, mechanical and design issues experienced during the year."

Jan 1, 2016

By T. Loos

The Norddeutsche Affinerie operates an Outokumpu-Flash-Furnace as a smelting unit. The pyrometallurgical slag cleaning process is based on the slag reduction and settling in the electric furnace. Since 1972 when the slag cleaning furnace was built the throughput could be increased fourfold. However, an extensive optimisation effort is required in order to keep the copper loss low. A parameter study with a neuronal network model based on real process data was conducted to identify parameters impacting on the copper loss in the slag. It could be demonstrated that the main parameters responsible for copper loss in the final slag are fixed parameters of the flash furnace. For a better understanding of the copper loss in the electric furnace microscopic analyses of the slag structure and viscosity measurements were performed. Based on these results the reduction and settling of the copper containing droplets could be increased in both pilot plant studies and industrial scale. 4

Jan 1, 2007

By A. Kowalski

Telvis Limited, manufacturer of an emergency communication dispatcher's broadcasting system, now introduces the possibility of a remote software upgrade to its devices. The paper presents methods, features and ways to accomplish this task. It describes the mechanisms used and the opportunities that arise from the use of this type of functionality. The mechanism software update presented applies to devices on the surface and in underground areas of mines. The electronics used currently allow the use of remote software updates, but the mining equipment makes little use of these methods. This paper aims to start the discussion on this topic and tries to lay the path of development by showing one of the first examples of the application.

Aug 1, 2013

1 INFORMATIONS GÉOLOGIQUES ET PLANIFICATION MINIÈRE La notion de gisement exploitable s'appuie sur les connaissances de géologie, d'ingénierie et tablir la rentabilité en fonction des investissements requis, des coûts de production, et des revenus qui sont tributaires de la demande et des prix des marchés. C'est une notion qui est d'abord diffuse lors de la découverte et de la première délimitation d'un gisement "d'intérêt économique potentiel" mais qui doit se confirmer et se préciser par des travaux additionnels pour devenir de plus en plus quantitative et assurée. 1.1 Informations géologiques Les conditions géologiques varient d'un gisement à l'autre (forme, dimensions, attitude, concentration et continuité -litages, effets de pépites - de la minéralisation). D'autre part, chaque méthodes minière a des contraintes différentes quant aux possibilités de sélectivité d'une part, d'acquisition d'information additionnelle lors du développement de la mine d'autre part. Cette problématique a été résumée au tableau 1, modifié de Vallée et al. (1993) [tableau 5, CIM Bulletin, avril 93, p. 74.].

May 1, 2002

By P. Tukkaraja, K. Katzenstein

"Block caving is one of the most economical and efficient underground mining methods and has gained popularity around the world especially for extracting low grade and massive ore bodies. However, during the extraction of ore from the draw bells, gases trapped inside the cave could emit into the working areas; hence, ventilation plays a key role in operating block cave mines successfully where gas emission is a concern. To design an effective ventilation system for a block caving mine, given the dynamic nature of the caving process, it is necessary to develop airflow characteristic curves (P-Q) for a given cave. This study uses a 1:100 scale physical model with an exhaust fan system, and a Computational Fluid Dynamics model of a block cave to investigate the airflow behavior through the cave filled with broken rock material. From this study, it was observed that the cave airflow resistance increases with the decrease in cave porosity and the particle size.INTRODUCTIONThe block cave mining method is gaining popularity owing to its low cost and high productivity. This study considered a case where this bulk mining method is used for the extraction of an orebody that contains uranium mineralization. During the extraction of broken ore from the draw bells, radioactive gases trapped in the cave zone could be released into the production drifts and could create unsafe working conditions in the mine. Mine ventilation systems play an important role in regulating the migration of radon in working areas. One of the strategies to control radon migration in a block cave mine is to exert negative pressure on the cave zone by using an exhaust fan above the cave zone. In order to select an appropriate exhaust fan system, it is necessary to study the airflow resistance of the cave zone (Loring & Nelson, 2006).Extraction of broken ore via drawpoints creates a void volume inside the cave called the air gap. Air gaps with larger heights can lead to air blasts in a block cave mine should the cave collapse. Besides that, the air gap can also lead to decrease in ventilation system efficiency due to recirculation of air flow and associated shock losses. Air gap height can also have a profound effect on the variation of cave airflow resistance (Erogul et al., 2015, 2017). The knowledge of cave airflow resistance is also important for predicting the intensity of an air blast. Cave airflow resistance is a function of cave properties such as broken rock size, air gap, and porosity inside the cave zone (Baysal et al., 2017). Initially, a scaled experimental model with a forcing system was developed to investigate the airflow behavior through the cave, however, this model couldn’t provide an observable change in the airflow resistance when the cave properties were changed (cave porosity, and airgap) This was attributed to the difficulties associated with forcing system in terms of achieving lower porosity values with the available material (lightweight shipping boxes) for simulating broken rock inside the cave zones, and controlling air leakage from the model (Ajitha et al., 2018)."

Jan 1, 2019

By W. R. Lindsay

Considerable attention has of late been given to the blasting of large amounts of ore in one operation, on account of the saving in labour and explosives and consequent low cost per ton, and also on account of the additional safety to employees. The blast here described, at the Hidden Creek mine. at Anyox, B.C., is not necessarily unique either in size or methods employed, but some interesting p10blems were encountered and the solutions of these may be of interest to others engaged in similar work. The ore consisted mainly of old scope-bottoms and sill pillars, although there also were some braces and parts of vertical pillars included. Some of the stope-bottoms were overlain by caved waste, and one of the problems was to break them in such a manner that the maximum amount of ore could be recovered without serious dilution with waste. The ore blocks, designated as the 385 silt and the 7 A-103 blocks, were under preparation for blasting for over a year, as conditions permitted. This work consisted in drilling long machine drill holes, varying in length from 14 to 20 feet. These holes were drilled with the Numa detachable bit, made locally, starting at 2~-inch diameter and bottoming at 2 inches for the longest length. The long hole drilling was used in the thinner sections of the area. For the stronger, thicker portions, powder drifts (3 ft. by 4 ft. in section) were driven for the powder charges. Reference to the plan and sections (Figures 2 co 8 inclusive) show the relative location of these, as well as the long drilling. The amount of explosives used in the powder drift charges averaged 0.25 pounds per ton of estimated burden, varying from 0.2 to 0.3 pounds per ton.

Jan 1, 1934

By W. Abdellah

Underground mine developments, such as haulage drifts and cross cuts, play a vital role in providing access to ore extraction areas for mine production. The stability of mine developments is thus of crucial importance during the life of a mine plan. Many Canadian mines use longhole mining methods or one of its variants. These methods require access to the orebody through mine developments such as haulage drifts and cross cuts on multiple levels. This paper examines the stability of mine development access intersections with respect to the planned mining sequence. A case study, the #1 Shear East orebody at Vale?s Garson Mine in Sudbury, Ontario, is presented. A three-dimensional, elastoplastic, finite difference model (FLAC 3D) was created for a development intersection situated 1.5 km below ground surface. The stability, or performance of the intersection, is evaluated in terms of the strength-to-stress ratio. The ratio threshold is set at 1.4 for temporary openings. Unsatisfactory performance is defined as a strength-to-stress ratio less than this threshold value. The performance of the intersection stability is evaluated at various modelled mining stages and the probabilistic method of analysis is then invoked to study the probability of unsatisfactory performance of the intersection. The results are presented and categorized with respect to probability, instability, and mining stage.

Aug 1, 2013

This paper focuses on the dissolution of various Manganese based compact additions into liquid Magnesium. The experimental procedure employed cylindrical compacts with various Manganese compositions. The various temperatures of the additions and the Magnesium bath were measured simultaneously during the immersion of the additions into Magnesium bath. The exothermicity level of these additions during their dissolution into liquid Magnesium was determined. The relation of the exothermicity level with the dissolution kinetics was also examined. In addition, SEM and EDX work was conducted for additions, which were withdrawn from the Magnesium bath. Finally, the recovery of these additions was estimated by taking samples from the Magnesium bath and conducting ICP analyses.

Jan 1, 2006

By \/eena Sahajwalla, Alexander Blagus

This paper reports the effect of using High Density Poly-Ethylene (HDPE)/coke blends on the reduction behaviour of Mn3O4 to MnO at 1000°C. The results suggest that CH4 release increases with increasing HDPE addition. The results show that the rapid release of methane, over only the initial five minutes, limited the interaction of Mn3O4/MnO with CH4. With the devolatilisation of HDPE there was increased porosity in samples containing HDPE, assumed to be the major factor in differences of reduction rates.

Jan 1, 2011

By F. Khomamizadeh

In this study the effect of solidification rate, T6 and T7 heat treatments on thermal fatigue resistance of A319 aluminum was investigated. Increasing of the solidification rate improved the thermal fatigue resistance of the alloy by refinement of the microstructure. The most sensible areas for thermal fatigue crack growth were the eutectic zones, T6 and T7 heat treatments improved the thermal fatigue resistance of the alloy by enhancing of the matrix resistance against the crack propagation. The slight reduction of the thermal fatigue resistance after T7 heat treatment is attributed to coarsening of the precipitates which reduces the matrix resistance.

Jan 1, 2005

By X. -P. Zhang, L. N. Y. Wong

Shale gas exploitation initiated in North America has rapidly extended worldwide. Hydraulic fracturing is an emerging field technique for stimulating the gas reservoir. The study of cracking processes, particularly crack coalescence, is vital for a successful hydraulic fracturing to enhance the gas exploitation. Experimental studies have observed that the size effects of the constituent particles are significant on the cracking behavior of the rock specimens. To further investigate the size effects, the bonded-particle model (BPM), which is based on the discrete element method (DEM), is adopted in the present research. In flaw-containing specimens, by varying the crack resolution (?= a/2R), which is the ratio of half flaw length (a) to particle size (2R), the size effects on cracking behavior under compressive loading are studied. By keeping the flaw length constant, the particle size is varied independently in the BPM analysis. Decreasing the crack resolution increases the first crack initiation stress, but it has no obvious effects on the uniaxial compressive strength. The trajectories of the first cracks and secondary cracks hence generated have a higher resolution and are well-defined in those specimens possessing a higher crack resolution. On the contrary, in lower crack resolution specimens, the macroscopic first cracks appear to be wider and less continuous. These findings from numerical simulation clearly demonstrate particle size effects on cracking behavior. Special attention should be paid to these effects in future numerical study using the bonded particle model.

Jan 1, 2015

By D. Bouchard, M. Forté, A. Charette

A transparent replica of a casting die was built to achieve a better understanding of the filling mechanisms of aluminum in high pressure die casting. Water and tomato paste were respectively used as analogues for the Newtonian liquid aluminum and the non-Newtonian semi-solid aluminum. The transparent die was installed on an industrial casting press and filling was filmed with a high-speed camera. Differences between the Newtonian and non-Newtonian fluids are presented and discussed.

Jan 1, 2006

By D. M. Xue, T. B. Li

"With the increase of human engineering activities, global climate change and active plate tectonics movement, the giant landslide frequently occurred in southwest China, which caused huge property and human losses. Besides, the potential landslides pose severely threaten to the construction and operation of airports, railways, highways and power stations etc. In order to provide accurate guidance for the landslide investigation, stability analysis and mitigation, the giant landslide is redefined according to landslide volume, depth of slip surface, complexity of landslide mechanisms, and degree of landslide mitigation difficulty, and classified with the typological classification approach based on the twofold attributes of landslide behavior including formation mechanisms and reactivation features. Finally, the threefold particularity of the giant landslide is also summarized, which enables a more effective landslide mitigation design.INTRODUCTIONWith the increase of anthropogenic activities, global climate change and active plate tectonics movement such as continual uplifting of Qinghai-Tibet plateau and strong earthquakes, the occurrence of giant landslides was in ascending trend in southwest China (Huang, 2009), which caused serious destruction, and greatly endangers such engineering construction from safety, time and economic aspects as airports, railways, highways, power stations, etc. Giant landslides have huge scale, complex formation/reactivation mechanisms and mechanical behavior. They may not be identified during the hazard investigation, but may be firstly initiated or reactivated due to the following engineering activities, heavy rainfall or strong earthquakes. Consequently, the landslide mitigation is inevitable and costly. However, it is difficult to control the deformation of giant landslide with lack of a correct understanding of genetic mechanisms (Marui, 2012; Zhang, 2000) and the excessive large sliding forces of the slide blocks calculated by the conventional limit equilibrium method. For instance, the failure of anchored pile wall for the No.102 giant ancient landslide (Zhu et al., 2012) and stabilization measures for the Sidi Rached viaduct landslide(Guemache et al., 2011); four rows of piles had not prevented the occurrence of the No.12 landslide in a high fill slope in the Panzhihua airport (Li et al., 2012)."

Jan 1, 2015

By G. T. Lapidus, R. Zárate-Gutiérrez

Selective leaching of lead from a Pb-Ag-Zn concentrate with hydrogen peroxide in citrate solutions was studied at room temperature. Leaching tests were performed, varying the H2O2 concentration and the solid-liquid ratio, holding the solution pH constant at 7, and the citrate concentration at 1 M. Lead extractions of 100 % were achieved with 4 and 5 times the stoichiometric quantity needed to form elemental sulfur, with only a small amount of metal impurities dissolved (Ag, Zn and Fe). The lead solubility limit at those conditions was found to be ~21 g L-1. X-ray diffraction analyses of the leach residues were free of galena (PbS), while other metal sulfides, such as sphalerite (ZnS), chalcopyrite (CuFeS2) and pyrite (FeS2), were basically unaffected.

Jan 1, 2014

High Pressure Grinding Rolls (HPGR) are said to be a good option in new grinding circuits. Due to their low energy consumption compared to other grinding systems such as SAG milling, there is a strong incentive to check their behaviour for certain ore types. With rising energy prices the operation will become even more beneficial in future. As published in the past, the HPGR is claimed to increase the liberation of the valuable mineral component within an ore. An investigation at the research centre of Polysius was conducted to substantiate the liberation behaviour in finish grinding operations. A pilot scale HPGR test unit (POLYCOM MAGRO) with a roll diameter of 950 mm and processing capacity of 80 t/h was used. Grinding tests were completed with a screen and a two stage drying air separation process (SEPOL). Analysis included standard screen analysis, fractional XRF and modern MLA technology. A technique was developed to oppose the amount of produced slimes (resuming bad flotation) against the positive effect of producing high mass fraction at flotation-easy sizes. The paper shows how effective the use of a dry grinding separation could be in terms of production of mass of liberated metal.

Jan 1, 2012

By Wm. F. Wuest

INTRODUCTION THE Western Canada sedimentary basin has one feature in common with the Precambrian Shield area: it also was a great chemical laboratory. The mining industry of Canada exploits the end products of chemical experiments that occurred on the Shield during periods of repeated disturbances in Precambrian times. The petroleum industry on the other band exploits what also appears to be the final results of chemical experiments that took place throughout all of post-Precambrian up to Tertiary times. Since the subject of this paper is a factual study of Alberta well waters, no attempt is made to answer significant questions pertaining to the probable role waters play in the generation of oil, or to the significance of the effects of structure and depth on waters. Data from several hundred well-water analyses were compiled by the writer in a series of charts and diagrams, of which those included in this paper are representative. Early studies indicated the possibility that outstanding anomalies in general concentration of waters and in greatly increased concentration of elements such as calcium, magnesium, bromine, and iodine for example, might be expected from wells that produced oil or were in the immediate vicinity of producers. The water analyses from wells which? were drilled at a later date did not confirm this possibility, and it is suggested that, aside from their initial value to the petroleum engineer or to. those interested in the commercial possibilities of brines, no definite significance as an aid in oil discovery can be attributed to water analyses.

Jan 1, 1951

By J. M. Hollicky

The economical processing of wet and sour natural gas presents a problem due to the seasonal demand for natural gas. The plants must be sized to handle the peak loads but may only operate at half capacity on the average, in which case the sales value of sulphur and hydro-carbon liquid by-products cannot support the operating and capital costs of the plant. This must result in an increased price for the gas. This problem was solved by Pacific Petroleums and Westcoast Transmission in the design of their pipeline and plant facilities now operating in the Peace River area, where there are both wet and dry gas fields. By .building a plant to process sufficient wet gas to pro-vide the base load requirement, and by drawing on the dry gas fields for peak loads, an optimum economic operation was ?possible. The sulphur, L.P.G., and gasoline produced not only are able to support the operating and capital costs of the pro-cessing plant, but were instrumental in the sharp drop in retail prices of these commodities in the area. The sour gas and condensate is gathered from the fields in the area and transmitted in a two-phase gathering system to the gas processing plant at Taylor, B.C. The condenrnte is knocked out in inlet scrubbers. Hydrogen sulphide and carbon dioxide are removed in an amine scrubbing unit. The hydrogen sulphide is stripped from the amine and is sent to the Jefferson Lake Sulphur Company's plant which produces sulphur by the partial oxidation of the hydrogen sulphide. The natural gas, now sweet, is processed in an absorption unit to recover additional liquids, before being de-hydrated to remove water. It is then sent to Westcoast's main c8mpression station. The condensate recovered in the inlet scrubbers and the liquid re-covered in the absorption unit are fractionated to remove fuel gas, used in the plant, and to produce pro-pane, butane, and naphtha. The pro-pane and butane are scrubbed with caustic soda to remove hydrogen sulphide. The naphtha is treated with hydrogen in a unifiner unit to re-move sulphur compounds completely, and is split into a light and heavy naphtha. The heavy naphtha is .catalytically reformed to produce a high-octane blending-component. These fractions are blended with components produced from crude oil at the Dawson Creek refinery to produce a high-quality balanced gasoline with special attention being paid to volatility for ease of starting, warm up, and engine cleanliness, and octane for power and ?performance.

Jan 1, 1958

By J. B. Boniwell

The INPUT electromagnetic prospecting system was originally developed by Dr. A. R. Barringer in an effort to increase the sensitivity and penetration of airborne EM methods. Although brought to an operational state some several years ago, it is only through relatively re-cent modifications and testing that some of the potential of the system has been fully realised. This is brought into perspective by some recent results over known ore deposits and geologic environments.

Jan 1, 1967

By A. Klingberg, M. Svensson, N. Smolko Schwarzmayr

"Removal of silicates and carbonates from sedimentary phosphate ores by the use of new synthetic collector/formulations was investigated in a comparative study with traditionally used collector systems as references. In the direct carbonate flotation the new formulations showed higher efficiency, contributed to an improved balance of P2O5 recovery and P2O5 enrichment in the recovered material. Efficiency of the new formulations containing synthetic surfactants was 1.5–2 times better than potassium salt of fatty acid sulfonate based formulations that are traditionally used for that purpose. The new formulations also provided up to 7% increase in P2O5 recovery at the same P2O5 grade. The new synthetic collectors for removal of silicates showed extremely good selectivity towards silica bearing minerals. The selectivity factor for the flotation tests when new formulations were used was 32–52 and for the flotation tests with the traditional collectors: 20–32. The ratio between distribution of an amount of silicates (as SiO2) and distribution of phosphate in the froth (waste) is defined as the selectivity factor. The new formulations provided more than 2% decrease of the amount of SiO2 at the same P2O5 recovery.INTRODUCTIONPopulation growth and decrease of arable land are the main reasons for constant increase of consumption of apatite (phosphate ore) in the fertilization field (Lannefors, Gorochovceva, Klingberg, Lima, & Gustafsson, 2015). Fertilizers play a key role for farmers to produce more with less land. The phosphate component of the fertilizer is vital for producing healthy and large amount of crop. As a result the demand for phosphate rock is growing.The largest producers of phosphate rock are the Unites States, Morocco, Tunisia, China, Russia, and Brazil. The term “phosphate ore” includes all phosphate-bearing minerals and rocks, but only two of them are of industrial interest: apatite (igneous origin) and sedimentary phosphate (Peres, Araujo, El-Shall, Zhang, & Abdel-Khalek, 2007). The majority of the world’s phosphate deposits are of the sedimentary type. There are two different types of sedimentary phosphates: siliceous and carbonaceous which are categorized based on gangue minerals (such as quartz, carbonates, mica, and clay)."

Jan 1, 2016

By F. K. McKean

THE task of establishing a new corrosion testing laboratory is more difficult than it need be because there is very little information on the subject available in the literature. Many articles describing tests and results may be found, but a wide search will unearth only passing remarks on the different types of equipment that may be selected for accelerated corrosion tests. An article describing some of the apparatus needed in a corrosion laboratory should be of help to those interested in building a new unit or in making additions to an old one. In May of this year, the writer was given the assignment of equipping a laboratory for general corrosion testing, to form a part of the new Physical Metallurgy Research Laboratories of the Department of Mines and Resource~ at Ottawa. With the help of senior members of the staff, along with what could be gathered from other sources, a list of necessary equipment was compiled and a plan for arranging it in the rooms was decided upon. Where possible, the apparatus was constructed in the excellent machine shops at the disposal of this Department, while the rest was placed on order with the manufacturers.

Jan 1, 1945