Search Documents

By Holt. Grover J.

"IntroductionThe history of iron ore production in the United States has followed a pattern not far different from that set in the production of non-ferrous ores; the first interest of the prospector and miner being the discovery and development of high-grade ores. In the early stages of development of most mining districts, high-cost low-grade ores are usually of slight interest due to the additional capital investment required in concentrating plants, as well as the increased requirements of •power and other facilities. As the reserves of higher grade ores are depleted and the technical knowledge of ore beneficiation is broadened, production of concentrates from the lower grade ores is stimulated.The real stimulus necessary to arouse serious consideration of beneficiated iron ore in the Lake Superior district has been provided by the serious inroads made in the high-grade ore reserves by two World Wars.The first shipment of high-grade iron ore from the Mesabi range in Minnesota was recorded in 1892, and the first token shipment of concentrates was made 15 years later, in 1907. Not until 1910 did the production of concentrates assume any great importance. A steady increase in concentrate production over the years is shown by the fact that, in 1910, concentrates accounted for 8 per cent of the total shipments from the State, whereas by the time of World War II this percentage had increased to 22 per cent and by 1948 had risen to 26 per cent. It seems a safe assumption that the shipment of concentrated iron ore, from the Mesabi range in particular, will continue to increase even more rapidly from now on, with other iron ranges of the Lake Superior district following this lead."

Jan 1, 1950

By F. A. Auld

"During the period 1958-1980 seven deep shafts were sunk from the surface in the UK. From 1977 until 1989 sixteen deep shafts were sunk in the UK, all concrete lined. Subsequently from 1989 up to the present day no deep shafts have been sunk in the UK, a period of 30 years. Developments in the design and construction of deep shaft linings in the UK therefore were predominantly carried out throughout the period 1977–1989. This knowledge is recorded in several published papers by the author over that period which will be referred to in the paper. INTRODUCTION The paper includes a review of past precedent for the design of deep shaft concrete linings in the UK and sets out the principles for future designs, including the design load to be adopted and Factors of Safety (SFs) to be used in the design. Hydrostatic pressure increases with depth from the surface and therefore the concrete lining must increase in thickness and strength throughout its depth to resist the pressure. High strength concrete mixes were developed to enable economic linings to reach greater depths and these will be detailed. The ground conditions to sink through in the UK consist of predominantly competent (self-standing when excavated) rock, which can be water bearing, and hence a hydrostatic pressure resisting lining is required. The paper describes the construction measures needed to produce a dry shaft by way of pour length, joint detail, backwall grouting and joint sealing details. PAST PRECEDENT FOR UK DEEP SHAFT SINKING AND LINING Seven deep shafts were sunk from the surface in the UK from 1957–1977 over a 20-year period (Auld, 1987). These are listed in Table 1. Three shafts were for British Coal, two were for Cleveland Potash Ltd and two were for the Central Electricity Generating Board. The British Coal shafts were 5.486 m and 7.315 m internal diameter to depths of 550 m and 780 m, respectively. At 5.5 m internal diameter and a depth of 1150 m, the two Boulby Mine shafts for Cleveland Potash Ltd are currently the deepest shafts in the UK. The two Central Electricity Generating Board shafts of 5 m and 10 m internal diameter, to depths of 255 m and 440 m, respectively, were ventilation shafts for a pumped storage scheme. Six of the shafts were sunk by Thyssen (GB) Ltd and one by Cementation Mining Ltd."

Jan 1, 2019

By A. A. McDonald

Anode casting has been in operation for two years in Hudson Bay Mining and Smelting's Flin Flon smelter. The new plant allows all casting to be done on one shift and so achieves considerable labour savings. The equipment and operations are described. Some important features are as follows: very consistent anode weights by the use of the load-cell controlled casting ladle; excellent mould life ; very low reject rate; and trouble-free take -off tower. Some of the start-up problems are described and an outline is given of the main operator functions. Data on labour, propane and maintenance costs are presented.

Jan 1, 1977

By D. G. Sinclair

In any discussion on the subject of mine-safety, it is well to honestly face the fact at the outset that mining is a hazardous occupation and that certain inherent dangers attach to the work, which, in spite of the greatest vigilance on the part of everyone concerned, will from time to time exact their toll of in jury or death from the underground worker. Great progress has been made of late years in narrowing down the range of these necessary risks, and, illustrative of what can be done along these lines by concerted effort, it is pleasing to read from time to time of large operating mines running for weeks, months, a year or more, without a single lost-time accident. To achieve any results in the work of accident prevention it is necessary, first, to have a definite goal, such as a no-accident period, be it a week, a month, or a year, to aim at; and, second, to set up definite standards to work by. The legal code of regulations should form the basis of all standards of work at every mine and should, for this reason, cover as far as possible all conceivable phases of operation. This represents the ideal, but in practice it is unattainable, largely because of the many variables that must be considered, due to the divergence in the scale of operations and to differing geological conditions at the different mines. Hence it becomes necessary for the operator who wishes to attain the maximum in the establishment of high standards of safe operation to so amplify the code as to meet the peculiar requirements of his operation.

Jan 1, 1930

By K. Jomoto, H. Majima

"Experimental work has been attempted to find a useful criterion of comminution which can be determined simply in a laboratory. The suitability of the ratio of the square of tensile strength to Young's modulus, St2/E, previously derived from the theory of elasticity as a criterion of comminution, was examined measuring tensile strength, Young's modulus and critical height for drop-weight impact of five different rocks. However, satisfactory correlation between St2 /E and critical height has not been obtained, suggesting the necessity of further experimental verification of the representative value of Young's modulus of rocks. The plot of St2 vs. critical height, however, shows one-to-one correspondence, and this finding suggests that St• may be a useful criterion of impact crushing. Also, a close relationship was observed between st• and the energy index for tumbling mill grinding of •the sample rocks. It is confirmed from these findings that the quantity St• is a useful criterion of comminution of rocks, not only for impact crushing but also for tumbling mill grinding. As shown in the experimental part of this paper, the determination ol St with irregularly shaped specimens is simple."

Jan 1, 1972

By G. Stenning

The paper outlines the need for high-volume ventilation in a uranium mining operation based on the design to meet environmental requirements for dust, radiation and diesel equipment. Mining methods in a highly mechanized operation, a key factor in design, are discussed. The construction and installation of major intake and exhaust fans are described briefly, together with the development of the mine airways and distribution system. Controls in the form of doors and bulkheads are important considerations in planning. Finally, the need to lower ventilation requirements in response to increasing power costs will result in future improvements.

Jan 1, 1979

By K. Adham

Both the dry and the wet fluorination systems require hydrogen fluoride (HF) for the process of uranium conversion to uranium hexafluoride (UF6). The dry methods depend on the electrolysis of HF to generate the fluorine (F2) required for the high temperature pyro-fluorination. The wet methods require aqueous HF in water solutions for the low temperature hydro-fluorination (Argonne, 2019). This paper uses the available HF safety guidelines and industry information to discuss the issues of transportation, storage and utilization. Health effects and environmental considerations are reviewed. Safe practices for handling the HF (both as anhydrous and as aqueous) are considered. Proper selection of different materials of construction are discussed, for both the anhydrous and the aqueous HF.

Jan 1, 2020

By A. G. Lylie

Introduction At the Britannia Mining and Smelting Company's mill, the equivalent of 2,500 to 2,800 pounds of copper sulphate crystals per day is made from copper which is precipitated from the mine-water. This copper sulphate is used in the mill for the recovery of sphalerite by2 flotation. From 1932 until 1936 it was produced by exposing the precipitate to air for thirty days and then dissolving the oxidized copper with dilute sulphuric acid. In 1936, the flotation of sphalerite was discontinued and, when it was resumed in 1947, steps were taken to try to improve the former method. The present paper outlines the way in which this was done, and describes the plant and procedure by which copper sulphate is now being made, and by means of which an appreciable saving is being effected. Aboratory Tests The previous work had established that the precipitate, which consists mainly of metallic copper, must be oxidized before the copper would dissolve in dilute sulphuric acid. Various methods for oxidizing it were tried but in the early laboratory work the only suitable one found was to heat the precipitate to 600°C. and hold it at this temperature for two hours. When this was done, approximately 90 per cent of the copper became soluble in .acid. This percentage was considered satisfactory for practical purposes, but the cost of roasting was prohibitive because only a small amount of roasted precipitate was required each day.

Jan 1, 1951

By J. Mullins

Coal was first banked by the Dominion Coal Company, Limited, in 1898, near No. 2 Colliery, the same site as is presently used for that purpose. Though today there are banks at Glace Bay, Sydney, and Sydney Mines, these notes, except when otherwise desirable, will be confined to describing the practice as developed at the No. 2 Banking Station, Glace Bay, as being typical of methods obtaining at all sites. Storing The manner in which the coal was piled is illustrated diagrammatically in the accompanying sketch. A train of coal was brought on the main trestle, which extended the full length of the banking ground at a height of 22 to 39 feet above the natural surface, and dumped into bins which were integral with the trestle work. Chutes from these bins permitted the coal to be fed into 3-ton cars, which were horse drawn laterally on narrow gauge tracks laid about 10 ft. centres, to a maximum distance of 400ft. from the trestle. These cars were end-dump and as the pile extended laterally the narrow gauge tracks were lengthened by shorter or longer filling pieces, so that their ends were always kept at the brow of the bank. Much coal, however, had to be dumped directly on the tracks and hand trimmed to fill the valleys, and level off, between the tracks.

Jan 1, 1931

By Grazyna Zakrzewska-Trznadel

The paper outlines the main objectives of the project that concern the evaluation of the possibility of uranium production from indigenous resources since Poland enters the nuclear program. The best available technologies are considered for uranium extraction and obtaining the yellow cake - U3O8. Liquid-liquid extraction with novel extracting agents, as well as membrane processes for separation of by-products will be tested in course of the project. The technological part will be completed with techno-economical analysis. Acknowledgement The studies were supported by the POIG project, No 01.01.02-14-094-09-00 ?Analysis of the possibility of uranium supply from domestic resources?.

Aug 1, 2010

By Anne-Marie Dagenais

Un recouvrement de type couverture à effets de barrière capillaire (CEBC) a été mis en place en 1988-1999 sur le parc à résidus de l?ancien site minier Lorraine situé au Témiscamingue. Depuis sa construction, la CEBC fait l?objet d?un programme d?auscultation et de suivi qui vise à évaluer son comportement hydrique et sa capacité à limiter le DMA. Des essais de consommation d?oxygène ponctuels ont également été réalisés sur le site afin de mesurer directement le flux d?oxygène traversant la couverture. Les résultats provenant des relevés de teneur en eau volumique et de succion, pour les années 1999 à 2001, montrent que les effets de barrière capillaire sont présents et que la couche de rétention d?eau demeure dans un état près de la saturation pour l?ensemble de la couverture. Les flux d?oxygène calculés à partir des mesures mensuelles sont en général inférieurs à 10 g/m2an, soit en deçà des valeurs de design de 20 à 40 g/m2an. Les essais de consommation d?oxygène réalisés sur la CEBC donnent également des flux d?oxygène du même ordre de grandeur. Les résultats obtenus de ces différentes méthodes d?évaluation concordent, et ils confirment l?efficacité de la CEBC à inhiber le flux d?oxygène et à contrôler le DMA.

Nov 1, 2002

By Guohong Yin

Oxidized sulfidic tailings contain significant amounts of accumulated acidity in the form of water-soluble secondary sulfate minerals and thus constitute long-term sources of acid drainage at many metal mining sites. As part of site remediation activities, alkaline amendments are often added to the oxidized tailings to increase the pH and immobilize the metals. This study assessed the advantages and limitations of using lime mud, a byproduct of Kraft pulp mills rich in calcium carbonate (> 90 wt. %), as alkaline amendment. The inorganic and organic constituents of lime mud samples were quantified. Leachable impurities were determined by the TCLP method. The performance of lime mud was compared to that of reagent grade quicklime (CaO) and calcite (CaCO3). Tailings treated with lime mud or calcite have strong buffering capacities and remain at neutral pH conditions (pH ~ 6.7) for long times. In contrast, tailings treated with quicklime have a very low buffering capacity, and their pH decreases with time. Furthermore, lime mud has finer particle sizes and thus a greater specific surface area than most forms of commercially available calcite, which results in enhanced reactivity. Dissolved metal concentrations are similar in tailings slurries treated with lime mud or calcite. This study suggests that lime mud is an environmentally and economically attractive alkaline amendment for oxidized mine tailings.

Nov 1, 2002

By W. R. Hopkins, J. A. Davis

"This paper presents a discussion of the mechanisms by which aerosols of the process electrolyte are entrained into the breathing environment of copper, Zinc and nickel eIectrowinning tankhouses. Literature outlining the health effects associated with worker & posure to the acidic and metallic contaminants found in the airbome aerosols is summarized and compared with existing North American regulations.A brief review of the existing technologies for the source reduction of these aerosols is presented. This paper outlines the industry experience with use of covers, balls, beads, shapes, fixtures and chemical surfaetants. Each of these devices is ranked according to its effusiveness in the process in which it is used, and rated according to its operator acceptance.The various forms of existing in-plant ventilation systems are reviewed with a discussion of their relative merits and effectiveness. Actual experience is related, detailing the methods of testing for ambient contaminant levels in a variety of tankhouse environments. Guidelines are provided for the site and process specific criteria which govern the selection and ultimate effectiveness of a particular form of ventilation system.Finally, actual project experience is cited in which hydraulic modelling is used a design tool in tankhouse ventilation design. These projects include the upgrading of existing traditional ventilation designs, and the ''grass roots"" design of a more efficient aerosol source control system to be used in high altitude, cold weather sites."

Jan 1, 1994

By A. Rahimi

Refractory castables based on alumina-silicate aggregates are commonly used in casting wheel components and launders. In this research the recycling process of waste magnesia chrome bricks for production of refractory castable lining for launders and casting wheel ladles at Iranian Sarcheshmeh copper complex (I.S.C.C.) is discussed. The smelting plant of ISCC consumes 4,000 tons refractory materials and produces 2,000 tons waste refractories annually. In order to reduce the environmental pollutions and gain the economical advantages, the recycling of waste refractories proved to be a solution [1]. In ISCC, 800 tons alumina or alumina-silicate refractory castables are used for linings of anode furnace ladles and launders annually [2]. In the present work, the spent bricks from reverberatory, converter and anode furnaces were analyzed in term of microstructural changes from hot zone to the cold end to evaluate the changes in texture and chemical composition. Different formulations based on recycled magnesia chrome aggregates and various particle size distribution and cement content were tested. Economic recycled magnesia chrome refractory mixture was prepared after crushing and sizing the non-deteriorated regions of wasted bricks. After evaluation of physical and mechanical properties of samples, one ton of refractory castable was prepared and successfully installed in the casting wheel ladles.

Jan 1, 2007

By R. B. Kaunda

One fundamental requirement for surface and underground rock engineering is the ability to characterise the rock mass. An accurate characterisation of the rock mass allows rock engineers to optimize designs safely and economically. A number of classification systems have been developed in the past 50 years to help characterise rock masses such as RMR, Q system, Rmi, and several others. The challenge in developing rock characterisation schemes is often practicality, i.e. creating systems with relatively simple inputs for the everyday practitioner. A second challenge is the degree of subjectivity often inherent in commonly used classification systems. These challenges are especially exacerbated in weak rock or densely jointed rock masses. This paper introduces a new approach to characterise densely jointed rock mass using artificial neural networks and principal component analysis, based on principles commonly used in the geotechnical engineering of rock fills and waste rock dumps. Thirteen input parameters are dimensionally compressed using principal component analysis. Using a global database with more than 100 case histories, an artificial neural network is developed to conduct the rock mass characterisation. The advantage of this approach is less subjectivity as commonly used engineering (quantitative) terms are put to use. A further advantage is that given that the method is site-data dependent, it allows for ‘fine tuning’ of the model for a specific site.

Jan 1, 2015

By G. A. Maki, P. J. Fullman, R. G. Roden

"In October 1984, Rocanville Division began using a stacking system to handle potash mill tailings. Previous to this date, mill tailings were slurried to the top of the tailings pile and allowed to debrine while flowing down the pile. With the new stacking system, slurried tailings are fed to mobile stackers. The stackers consist of cyclone packs to debrine the tailings and drag conveyors with screw discharges to deposit the tailings onto the existing pile. This paper deals with the various aspects of the project from conception to its present state.IntroductionPrevious to 1984, when the stacking project was first implemented, potash mill tailings were handled as follows. Mill tailings were first debrined to approximately 65010 solids using a cyclone cluster. The cyclone underflows were then introduced onto a vacuum scroll filter table. Here the tailings were further debrined and discharged into the disposal tank where the tailings were reslurried with reclaim brine and pumped to the tailings disposal site. At the disposal site the slurry was discharged onto the tailings pile and by a natural settling process the tailings were debrined with the brine ultimately collected in the reclaim brine ponds. The shape and profile of the tailings pile was controlled by building salt dykes to control the flow of the discharged tailings slurry. As the tailings pile grew in height, booster pumps were added to the disposal system."

Jan 1, 1990

By G. W. Evatt

This paper presents the scientific framework underpinning the Resource Valuation and Optimisation Model (RVOM). The RVOM is a Real Options software package, which helps mine owners optimally plan their operations, understand their project risks, and make defensible valuations. This is achieved in the presence of both financial and physical uncertainty. The three key outputs from the RVOM are: Valuation, Optimal Decision and Probability of Decision, where a decision can include any combination of: normal operation, expanded operation, care and maintenance, and abandonment (and variants thereof). This paper presents a clear example of the RVOMs usage to a case-study gold mine.

Jan 1, 2011

By G. S. Hume

THE discovery of natural gas with naphtha in 1924 in the Upper Palaeozoic limestone of Turner Valley, 35 miles southwest of Calgary, has led to continuous developments in this field. Drilling undertaken soon after this discovery demonstrated that the anticlinal structure was in reality a major drag-fold cut off on the east side by a westerly inclined fault of large displacement. The faulted edge of the .limestone at depth determines the eastern limits of the field, which between 1924 and 1936 was shown to have a gas area 14 miles long by about 1 mile wide. Since the strata dip westerly, away from the axis of the fold, drilling becomes progressively deeper to the west and, with the advent of deeper drilling, crude oil was discovered in 1936 on the west flank of the structure but in the same porous reservoir rocks as the gas on the crest and upper parts of the fold. Since 1936, drilling has been undertaken wholly for the production of crude-oil and at present two producing areas have been found within the Turner Valley structure. The larger of these, at the south end of the field, in the vicinity of Highwood river, has a length of about 4 3/4 miles and a proved width of one mile, whereas the smaller, in the north end of the field, south of the north fork of Sheep river, has only a few producing wells.

Jan 1, 1939

By J. Lui

At its Copper Cliff Smelter, bulk nickel and copper concentrate is processed in two Inca flash furnaces and Peirce Smith converters to produce Bessemer matte containing 0.6%Fe. After slow cooling and Matte Separation, Bessemer matte is converted into three main products using magnetic separation and flotation technology: (1) a nickel containing chalcocite concentrate (MK); (2) two types of copper containing nickel sulfide (ME and MR); (3) metallics (MYN). MK is further processed in the Inca top blowing bottom stirring MK Reactor to produce semi-blister copper containing ~4%Ni and ~3±1 %S. The semi-blister copper is then purified in the multi-purpose vessels (MPV) to produce blister copper by reducing Ni, Fe and S content through oxidation. High melting point NiO is formed inside the MPVs. The accumulation of solid NiO and other oxides requires periodic cleaning by adding reductant and furnace matte, a unique process called "washout" at Inca. For many years, the reductant used for the "washout" process has been 15%Si Ferro-silicon. With increasing cost and limited suppliers for 15%FeSi, alternative reductants were pursued. This paper summarizes the development and commercialization of new alternative reductants for MPV "washout".

Jan 1, 2007

By Peter McBride

Human excellence in all areas of endeavour is acknowledged and recognized. Establishing role models and spreading the word on best practices helps broader audiences. For on-the-job safety, recognition awards are a component of successful programs. In Canada?s mining industry since 1941, the John T. Ryan Safety Trophies initiative has contributed to the sector?s improving record in this area. The much sought after and rich in history John T. Ryan trophies are recognized symbols of safety excellence in Canada. The effectiveness of the Ryan safety recognition program in Canada has led to its export to other mining countries seeking to improve their overall safety performance.

May 1, 2008