Search Documents

By Stephen C. Tadolini

"The use of a torque wrench to establish the amount of actual load developed on an expansion anchor bofting system dates back to work completed in the early 1950s. The advent of ultrasonic measurement systems and hydraulic torque wrenches has made it possible for the U.S. Bureau of Mines to perform torque-tension measurements in the laboratory and the field much more accurately. The results indicate that the amount of initial boft preload may be overestimated by amounts in excess of 45% of the expected load using torque wrenches. This inaccuracy is primarily due to the friction that occurs between the bearing plate and the head of the boft. These parameters become extremely important when the support system is being used to prevent joint members from slipping relative to each other or when the boft acts as a heavy spring to clamp two or more sections together. Methods to overcome the frictional losses are presented in conjunction with a laboratory method to determine the actual torque-tension ratios for expansion anchor and combination bolting systems.IntroductionMechanically anchored roof bolts have been widely used in the mining industry since their introduction in 1947. Estimates made in 1989 indicate that out of 85 million fixtures, approximately 49 million bolting fixtures still use applied tension to complete the reinforcement necessary to maintain stable openings. Nearly 85 million bolts are used yearly. The most widely used bolt is the resin-anchored headed rebar, followed by standard mechanical roof bolts, specialty bolts (mechanically anchored, resin enhanced fixtures) , and combination bolts . Po st-tensioned resin rebars, combination systems, and friction stabilizers make up the remaining 10% of the units used (Fig. I).For mechanical, combination, and tension rebar bolts, the bolt tension is the primary means of reinforcing the roof, but in many cases, because of poor installation procedures, the bolts are ineffective. Mine operators recognize the importance of proper installation procedures. Long-term bolt tension measurements are required in the Code of Federal Regulations (CFR)In each bolting cycle, the actual torque or tension of the first tensioned bolt installed with each drill head shall be measured immediately after it is installed. Thereafter, for each drill head used, at least one roof bolt out of every four installed shall be measured for actual torque or tension. If the actual torque or tension of any roof bolts measured is not within the range specified in the roof control plan, corrective action shall be taken."

Jan 1, 1991

By E. M. De Souza, R. Penner

"Water is encountered at the majority of underground mines, both over their lifetime and during each stage of development and production. The dewatering system is one of the most important and costly components of an underground mining operation and it is often not well designed and analyzed. An effective design of a mine dewatering system will greatly reduce its energy cost as well as improve working conditions and reduce production costs. A computer-based system, called Qpump, has been developed to assist the underground operator to effectively design and/or assess over-all and local mine dewatering systems. The design features and principles used in the development of Qpump are introduced and an example which illustrates typical applications is presented.IntroductionTraditionally, dewatering operations have been given lower priority than many other operations in underground mining. Invariably water will be encountered during the sinking of the mine shaft, during development and subsequent production. The dewatering system thus becomes a very important component of an underground mine operation and, in fact, any mine manager will attest to the importance and necessity of an efficient mine dewatering system.The water problem is of varying importance at different mines. There are several factors that contribute to the water encountered. It is a function of the mining method and techniques utilized (backfill system, drilling and raising technology, dust control sprays, shaft water rings, etc.) and of prevailing conditions (ground water, rock structure and permeability). In some cases a mine may be so dry that little pumping is required while in others, the weight of water pumped may exceed by many times that of ore mined.The successful design and application of a mine dewatering system is dependent upon the operating conditions of each specific operation. There are no standard procedures and systems which can be used for all mining situations. However, an effective water system will greatly reduce the energy and production costs of a mine, improve working conditions and eliminate headaches because of flooded working places."

Jan 1, 1993

By Matt Manson

?? Current Exploration and Assessment ?? Overview of Potential Development ?? Infrastructure ?? Opportunities and Challenges ?? Renard? 1-10 kimberlite pipes and ?Lynx-Hibou? kimberlite dyke system within ?Foxtrot? property ?? 50/50 Joint Venture between Ashton (a subsidiary of Stornoway) and SOQUEM ?? Discovered 2001-2003 ?? Québec is routinely assessed as one of the top mining jurisdictions in the world ?? Agnico-Eagle Mines Ltd. Is Stornoway?s largest shareholder and a leading mine developer in Québec

May 1, 2008

By Ali M. Ghazi, Ronald J. Goble, Lowell S. Whiteside

"Geerite (Cu1.6S) is a rhombohedral copper sulphide which occurs naturally in epitactic replacement of sphalerite; cell dimensions closely approximate those of the host sphalerite.Geerite-type structures can be produced by leaching digenite (Cu1.8S) in ferric sulphate solutions. X -ray diffract ion and electron microprobe studies indicate that eight metastable geeritetype structures can be produced, depending upon the concentration of f erric sulphate solution used and the duration of the each. Although compositions cluster on or near values observed for natural phases, optical properties indicate that we are dealing with polymorphs of these phases. Leaching of chalcocite (CU2Sj in dilute f erric sulphate solutions produces similar results. In contrast, leaching of chalcocite in more concentrated solutions seems to produce true analogues of natural minerals.During froth flotation, sphalerite is activated with a monolayer of floatable copper sulphide with the composition, CuS, of the mineral covellite. However, covellite is not significantly more floatable than sphalerite, and has an incompatible structure because of the presence of covalently-bonded atoms of sulphur. Leaching ofdigenite was used to produce a polymorph of covellite with a geerite-type structure, compatible with that of sphalerite. This polymorph has a flotational behaviour similar to copper-activated sphalerite, suggesting that the monolayer has a geerite-type CuS structure. IntroductionIn an ideal close-packed sulphide structure the distance between sulphur layers, D, is equal to 2R 2/3, where R is the radius of the sulphur atoms. In sulphides with covalently-bonded sulphur layers, such as covellite (Fig. I), D will be an average of the number of covalentl y-bonded and close-packed sulphur layers, weighted as to the relative number of each type of layer. Both D and R are spacings which are readily identifiable structurally and on X-ray diffraction patterns. Goblel has shown that for copper-iron sulphides with metal-to-sulphur ratios between 0 and 2 and copper-to-total metal ratio s between 113 and I there are strong correlations between composition and measured D and R distances (Fig. 2). D can be represented by a single empirical equation relating interlayer spacing to composition; R must be represented by three equations relating the radius of sulphur atoms to composition. One of these equations (R, in Fig. 2) represents ideal close-packed behaviour, the other two represent sulphur radii greater than (R1) or less than (Rh) the ideal."

Jan 1, 1988

By Arsalan Talebzadeh

Construction -Surface ?First two intake fans constructed in 2007; third fan added in 2008 to reduce resistance in the system. 450 HP fans. ?Excavation for exhaust fans started in 2008. ?In parallel with underground construction in preparation for the changeover. ?Bulkhead in place prior to completion/ commissioning of

Oct 1, 2010

By P. O. Parfitt

The Critical Path Method has proved its usefulness at Mcintyre Porcupine Mines Ltd. This paper illustrates the techniques of network construction and analysis, and the application of the method at the Mcintyre copper mine to various projects in the gold mine. C.P.M.'s use in a mill maintenance project is also discussed.

Jan 1, 1966

"ALTHOUGH Canadian metallurgists have long been active in research, the scope of the work was somewhat limited until the be-ginning -of World War II. The rapid industrial development of Canada during the past ten years has been accompanied by .a similar upsurge in research. However, the wide geographical distribution of the research centres has made it difficult for the individual research workers to meet together and to exchange ideas or even to learn what projects .are being investigated or the nature and extent of the facilities available for work of this kind.The purpose of the present symposium is to assemble data relating to projects under investigation and the facilities employed at the various metallurgical research laboratories in Canada, thus providing some measure of correlation so that workers in different locations may learn what kind of work •is being .done at other points throughout the country.In reporting the symposium it has not been possible to reproduce the papers in full, but excerpts have been selected that give the essentia1 data."

Jan 1, 1952

By Rodolfo Zanella

Au/TiO2 catalysts prepared by deposition-precipitation with NaOH (DPN) (~3 wt%) and urea (DPU) (~8 wt%) were tested in crotonaldehyde hydrogenation at atmospheric pressure. There is no differences in activity (mole.gAu -1 s-1) and selectivity between both DPU and DPN samples for a given activation treatment. This is due to the fact that DPU and DPN samples exhibit similar gold particle size distribution, although the gold loading in DPU is much higher that in DPN. The DPU samples were reduced under H2 at different temperatures (120-500 °C) or under air at 300 °C with various flow rates, to vary the average particle size within a large range, 1.7 to 8.7 nm. The selectivity to crotyl alcohol (selective hydrogenation of the carbonyl bond) is high, 60-70 %, and almost constant as a function of the particle size. The selectivity to crotyl alcohol is also constant for conversions between 10 and 50%. These results suggest that the adsorption mode of crotonaldehyde is of ?3 or ?4-type. In contrast, the TOF depends on the gold particle size, it drastically increases when the gold particle size is ~2 nm. Our results are in agreement with former studies that suggest that the gold atoms involved in the hydrogenation process are those of low coordination.

Oct 1, 2003

By Anoush Ebrahimi

Mining dilution is one of the most important factors affecting the economy of mining projects. Ore losses and dilution are present at all stages of mining and while several models can investigate the influence of dilution it is its quantification that poses the most serious challenge (Pakalnis et al., 1995). This paper introduces a methodology to quantify dilution factor in open pit mines. The proposed approach makes use of general mining software available in most mining companies. Therefore it is amenable to most mining operations and provides a readily available tool for understanding mining dilution for operators and consultants. To illustrate the methodology the author uses an example from a hypothetical mine. Dilution increases the operating costs in the mill by increasing the tonnage of material to be milled. In addition to its direct impact on short term income of a mine, dilution causes significant changes in other factors that on the long term reduce the overall value of the project. For example, it prolongs the mine life by reducing mill?s effective capacity. It also reduces the feed grade. In most cases, lower feed grade means lower mill recovery. Dilution also increases the cut-off grade which in turn reduces the overall ore utilization of a mine. In some cases, to take advantage of economies of scale, mining operations tend to plan for higher mining rates. Moving to a larger scale of operation means less selectivity, hence more dilution. This is true for all kind of deposits. High level and uncontrolled dilution may ultimately defeat the purpose of increasing production rates. If not impossible in theory it is nevertheless extremely difficult and expensive to eliminate dilution in practice. Some amount of dilution is practically unavoidable in most mining operations (Scoble and Moss, 1994). Although completely avoiding dilution may be impossible, we can measure and control it. By better understanding the root causes of the dilution and planning accordingly, it can be controlled and reduced. While we do our best to identify and calculate all the other cost items of a project, no matter how small, it is common to make general assumptions about dilution instead of quantifying it. It is common to assume a general dilution such as 5% for massive deposits and 10% for tabular shape deposits. While these figures may be a good starting point in early stages of mining studies, it does not take in to consideration the complexity of the problem. Dilution factor varies within a single mine for different benches and zones. This is due to changes we see in grade distribution and shape of ore body. It also varies based on commodity price. It is necessary to make sure that these variations are taken into account when designing or evaluating a mine. Dilution varies in different mines based on the deposit characteristics, operational aspects and economic cut-off grade. For instance, shape of the deposit, bench height, equipment size, and market conditions will have an impact on the level of dilution in a mine. It is paramount for mining projects to have a better understanding of dilution right from the beginning. In times like today, where mining operations must operate at peak efficiency, it is even more crucial to be able to calculate and have a better grasp of all the parameters influencing the economics of a project including dilution. In order to produce better project evaluations, dilution studies should be an integral part of any project.

Aug 1, 2013

By J. Scrimgeour

"The word ""instrumentation"" has expanded from its original meaning, which in engineering perhaps referred to measuring apparatus alone. In its broadest form, it now includes sensors, display instrumentation, standard pack-aged controllers and, most recently, the use of stored program computers for on-line process control. The paper traces the evolution, in tutorial form, of the successive application of mechanization, measurement instrumentation, automatic control, central operating systems, programmed control, process computer control, direct digital control and, finally, hierarchies of computers used for process control and corporate management as a fully integrated business system. In the field of industrial minerals, the cement industry has seen the most widespread acceptance of these techniques. Computer control has been accepted as the way of life for the blending of chemical materials and for on-line control of the cement kiln. Accordingly, the cement application is selected for further presentation in the paper. This illustrates the trend progressing from control of single loops on process variables toward the objective of total control of the product quality. The economic justification for instrumentation, centralized control, automatic control and computer control is .discussed with reference to savings in fuel, maintenance, operating labour, depreciation, power and product quality improvements."

Jan 1, 1967

By E. Ghali

"Corrosion of support system components (e.g., bolts, mesh, plates) is a safety and economic concern in underground mines. This paper reports the results of a five-year study wherein corrosion coupons were installed at select locations in participating mines, recovered at regular intervals, analyzed for signs of corrosion, and tested to quantify loss in capacity. Complementary tests were conducted on recovered mesh and friction bolt specimens. The data provide insights into contributing factors for support systems corrosion, which aid in the selection of appropriate support strategies and reliable assessment of the useful life and need for rehabilitation of a support system.RÉSUMÉ La corrosion des composantes des systèmes de soutien (p. ex. boulons, grillages et plaques) est une préoccupation économique et de sécurité dans les mines souterraines. Cet article présente les résultats d’une étude de cinq ans pendant laquelle des coupons de corrosion ont été installés à des endroits spécifiques dans les mines participantes; ces coupons ont été retirés à des intervalles réguliers, analysés pour des signes de corrosion et mis à l’épreuve pour quantifier la perte de capacité. Des essais complémentaires ont été effectués sur les grillages récupérés et sur les échantillons de boulons d’ancrage. Les données aident à comprendre les facteurs qui contribuent à la corrosion des systèmes de soutien, ce qui est utile dans le choix de stratégies appropriées de soutien et pour une évaluation fiable de la durée de vie utile et du besoin de remise en état d’un système de soutien."

Jan 1, 2015

By L. Veleva, Garcia. A., G. Perez

Aluminum is a metal used for the transmission of electricity of high voltage, in the construction industry and other areas. In atmospheric conditions aluminum forms an oxide layer (Alz03'H20) as a result of its corrosion, entering the passive state. The oxide layer can be destroyed by the presence of ions (Cr, SOx-n) developing localized (non uniform) corrosion attack by pitting, difficult for evaluation. The concepts of fractals and self-similarity were used in this study for the characterization of the development of localized corrosion. Images obtained with a scanning electron microscope (SEM) of samples of electrolytic aluminum wire that have been exposed during one year in ruralurban and marine-coastal environments of the humid tropical climate of Mexico, have been processed. The development of pitting has been studied as a function of time, making a statistics of the frequency of appearance of pits versus the area occupied by them. The data show that the distribution of the pits follows a power law. Therefore, the concept of self-similarity can be applied for the study of the phenomenon of localized corrosion, describing their development with time.

Jan 1, 2006

By David Eichenberg

A154S A154N After 3 Years of Mining ?Current mining Level A154S 280RL ?110 Vertical metres of A154S ?Current mining Level A154N 300RL ?100 Vertical metres of A154N ?Variations in Kimberlite Volume ?Ore Types and Plant Production

May 1, 2006

By D. A. Beck

The load-deformation response of discontinuous rock under static and dynamic loading conditions has been simulated using Explicit Finite Element models. The intent of the analysis was to investigate the effects of specimen size and confining stress on strength, dilation and comminution. The simulations allow the development of homogenised constitutive material properties for discontinuous rock masses using laboratory scale measurements and representative Discrete Fracture Networks (DFNs). A procedure for this is presented which includes a comparison of measured seismic response in a mine to the Dissipated Plastic Energy (DPE) that is released in the simulated rock masses. The models also show how confinement and scale affect the stress-strain and DPE response of the simulated rock specimens, reproducing a number of known rock phenomena that are often poorly captured in geotechnical modelling. A case study is presented showing a satisfactory match between the model-derived, homogenised material properties and values achieved by calibration of a mine-scale model where many thousands of seismic, displacement and damage measurements were available.

May 1, 2009

By Alex Rown

"THE SYDNEY COAL FIELD has long been afflicted by high costs and low productivities. However, a distinct possibility now exists that improvements can be made in costs, productivities and revenues. If these hopes materialize, the Sydney coal field will once again be regarded as a valuable asset in our national inventory of energy and metallurgical coals. The economic possibilities for the Sydney collieries depend on performance at the pits and in the market place. Because this audience is already well informed about colliery planning, I would like to start with an assessment of the modern coal market insofar as it may relate to the Sydney field. Since 1950 we have seen a vast growth in the population and industrial empires of the western world which has resulted in an enormous and escalating demand for energy. If the energy supply pattern of the first 50 years of this century had been followed, this would have led to an immense demand for coal."

Jan 1, 1972

By Mengmeng Gai

This paper introduces a model-based automatic object recognition and registration framework to assist heavy equipment operators in rapidly perceiving 3D working environment at dynamic construction sites. A video camera and a laser scanner were utilized in this study to rapidly recognize and register dynamic target objects in a 3D space by dynamically separating target object?s point cloud data from a background scene for a quick computing process. A smart scan data updating method has been developed which only updates the dynamic target object?s point cloud data while keeping the previously scanned static work environments. Extracted target areas containing 3D point clouds were orthographically projected into a series of 2D planes with a rotation center located in the target?s vertical-middle line. Prepared 2D templates were compared to these 2D planes by extracting SURF features. Point cloud bundles of the target were recognized, and followed by the prepared CAD model?s registration to the templates. The field experimental results show that the proposed rapid workspace modeling method can significantly improve heavy construction equipment operations and automated equipment control by rapidly modeling dynamic target objects in a 3D view.

Aug 1, 2013

By C. J. Edmonds, R. Bland, W. C. Ferguson, R. Whitehead

"In 1969, the Environmental Science Division of James F. MacLaren Limited received authorization from The International Nickel Company of Canada, Limited to carry out a water quality monitoring program in the Lake Shebandowan region of Ontario, where a new base metal mining and milling complex was expected to go into operation in 1972. The objective of the program is to establish base-line water quality characteristics. Fully realizing their corporate responsibility to minimize the effects of the proposed activities on the environment, Inco decided that it would be desirable to establish a program by which any change in the quality of environmental waters will be detected before detrimental conditions ensue, permitting prompt corrective measures to be taken. The program has been in progress for over two years. The waters are sampled and analyzed four to six times per year. Sampling stations are located in Lake Shebandowan and on the adjacent Gold Creek - Matawin River system. On-site analyses and measurements are made of flow, dissolved oxygen, temperature and pH. Samples also are collected for later analysis in the laboratory. These samples are analyzed for a wide range of chemical and biological characteristics. The paper discusses the extent of the sampling program, the techniques utilized and the value of such programs in maintaining the quality of the environment."

Jan 1, 1973

By A. R. Turner

AERIAL survey methods have made enormous technical advances and gained new recognition since World War II. Before enlarging on this statement and reviewing some of the uses of aerial survey in industrial development it is important to de-fine what is meant by "aerial survey". The subject will be discussed in the broadest sense and references will be made to the four sections that compose the overall field of surveying operations from the air. These are: 1. Aerial photography and photo-graphic mapping. 2. The use of airborne electronic instruments for geodetic distance measurement and the determination of ground elevations. 3. Airborne geophysical surveying. 4. The extraction of qualitative and quantitative information from aerial photographs through the processes of "reading", analysis and interpretation. Many sciences and techniques are combined in aerial survey operations. The tools of the business include aircraft, finely engineered cameras, elaborate film processing and printing equipment, ground survey instruments, precision stereo-plotting instruments, map -

Jan 1, 1961

By Shuji Owada

Scrap electrical and electronic appliances, so called "E-waste", are not a present target to be collected and recycled under Japanese regulations. This material, however, contains considerable amounts of base, precious, and rare metals and it is necessary to recover these elements for maintaining stable supply and establishing "the society of environmentally-sound material-cycle". This paper describes recent trends of rare metals recycling in Japan and technological approaches to achieve the above objective. Also a research work to concentrate rare metals from the printed wiring boards by combining brand new comminution and physical separation methods is discussed.

Jan 1, 2011

By Rick Coleman, Chelvan (Chevy) Veloo

"P.T. Freeport Indonesia's lrian Jaya Operation has been producing copper concentrate continuously since 1972. Numerous ore discoveries and five mill expansion programs have seen the initial milling rate of 7,200 MTPD escalate to the present rate of 125,000 MTPD, producing 2.5 million pounds of copper and 3,500 troy ounces of gold per day. The latest expansion, commissioned in February 1995, incorporates a 34 foot Semi- Autogenous Grinding (SAG) Mill, two 20'x30' Ball Mills, conventional roughing, cleaner column flotation, and attendant upgrades to the existing concentrate pumping and dewatering facilities. This paper will describe the SAG Plant flowsheet, and focus on the key training issues which contributed to a successful plant start-up.IntroductionP.T. Freeport Indonesia's operations in the Ertsberg mining district are located in the Jayawijaya Mountains of Irian Jaya, the easternmost province of the Republic of Indonesia. P.T. Freeport Indonesia (PTFI), the operator, is owned by Freeport MacMoRan Copper and Gold (81.3%), the Government of Indonesia (9.4%), and private Indonesian investors (9.4%). Geographical location, and sailing distances are provided on the attached location map.The operation stretches over 7 4 miles ( 114 km) from the dewatering and concentrate shipping facility at the Port of Amamapare on the Arafura Sea to the Grasberg open pit located at 3400m. The regional geology is covered in detail by Van Nort et al (1991 ), with current proven and probable reserves estimated at 1.13 billion metric tonnes grading 1.30% Copper, 1.42 ppm Gold, and 4.06 ppm Silver. The Grasberg open pit mining operation provides 92% of the mill feed, and is described in detail by Hickson (1991). The remainder of the mill feed is derived from several underground block caving operations. Current production rates provide a mine life in excess of 25 years. However, very favorable geology in the area leads to expectations that additional reserves will extend the life of the operation considerably."

Jan 1, 1996