Search Documents

By C R. Fountain, W R. Cannings

The zinc-lead-silver mineral resource at Lady Loretta ranks amongst the worldÆs richest when measured in terms of in situ metal grades. However, the project remains undeveloped 28 years after its discovery in 1969. The primary obstacle to development has been the fine and complex grain structure of its ores, which make flotation concentration inefficient even with fine grinding. The size and remote location of the deposit have also hindered exploitation. BUKA planned to directly fume the volatile target metals from the ore when it acquired the project. Intensive, post-acquisition modeling showed the innovative processing route to be uneconomic, notwithstanding high metals recovery and low waste content in fume product. Progressive modifications and supplements to the underlying fuming process enhanced economics and resulted in a new mine-to-metal processing route for zinc-lead-silver ores. The proprietary, three-stage BUKA Zinc Process offers technical, economic and environmental advantages. It is expected to find widespread application in the treatment of ores and residues. However, neither continued R&D nor application to Lady LorettaÆs currently delineated resource can be justified under prevailing market conditions. The objectives and results of each step in the process development sequence are outlined with reference to their impact on the commercial viability of the Lady Loretta project.

Jan 1, 1998

By D Kahler

Modern gold production from the Gympie Goldfield commenced in 1995 with the first production from the Monkland Mine. The primary ore target was the 2.5 m wide Inglewood Fault ore zone, which was initially mined using traditional narrow-vein shrink stoping. This manuallyintensive mining method allowed the mine to re-open with minimal capital cost, however the trade off was low productivity and high operating costs. As the mine has developed, access through 100-year-old, timber-lined, small shafts, and the high cost of delineating reserves, has restricted modernisation of the operations. In early-2000 a stockwork lode was discovered adjacent to the existing workings with an economic width of 40 m. In order to maximise the benefit of such an orebody, mining needed to be approached in a new way. This paper summarises the many changes implemented at the Monkland Mine, including the necessary cultural change, implementing long-hole stoping, de-bottlenecking and the application of mechanisation. The result has been a significant improvement in safety performance, higher productivity and a more secure future for all those involved in the project.

Jan 1, 2002

Designing and constructing OxianaÆs Sepon gold and copper operations in one of the most remote areas in Laos has been a great achievement; one which was recognised by the engineering industryÆs highest accolade û the Australian Engineering Excellence Award in 2005. The developing nation of Laos has no previous mining or heavy industrial experience, but the support of the Lao Government and a remarkable Lao workforce has enabled the project to be developed and operate as well as it would anywhere else in the world.When making a decision to invest offshore, several geophysical and jurisdictional criteria need to be considered. Laos offers unparalleled prospectivity, a central location with growing infrastructure, a ready workforce and a developing but supportive regulatory regime. In addition, the Sepon copper project has exceptional characteristics, including its high grades, location near the surface, leachable qualities, access to hydropower and the ability to produce cathodes on site. These attributes and its location in the centre of a region hungry for resources contributes to the projectÆs excellent economics.

Jan 1, 2006

How do you initiate closure planning for a mine site that is on the doorstep of a major community without generating the extremes of panic or complacency? That is the question that is faced by Australia's largest gold mine, the Kalgoorlie Consolidated Gold Mines (KCGM) Super Pit in Kalgoorlie-Boulder. KCGM's Community Relations Manager, Danielle van Kampen, will reveal the lengthy closure planning process that is in train to alert yet not alarm the community about the future of the Super Pit and to generate discussion on issues of importance. What will happen to the 'big hole' that generates both mining and tourism dollars for the City of Kalgoorlie-Boulder as its anticipated closure date of 2021 comes closer? How do you communicate a constantly evolving closure date? Although the process may generate more questions than answers, the project will be discussed at length and with the added benefit of independent community recent research in the form of the public 2009 Closure Consultation and the KCGM 2010 Social Impact Assessment. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Jun 1, 2010

The introduction of a new mining method to Australia is not without its risks and challenges. This paper discusses the processes of planning a new operation, with particular emphasis on block caving and its Northparkes adaptation. As well as applying advanced technologies, here also is the opportunity to develop the art and science of block caving for its application to a wider range of geotechnical conditions than previously Envisaged.

Jan 1, 1995

The mining industry is quite often faced with declining selling prices for its products in the face of rising prices for the input cost resources that it uses. Blasting is a key activity within the mining system and has a vital role to play within the Mine to MillTM concept. It is therefore important that blasting makes a positive contribution to mine profit and productivity. There are several variables involved in considering the profitability and productivity of blasting. The rock types and structures, the bench height, the blast hole drill rig specifications, hole diameter, spacing and burden, explosive loading and initiation and blast size fragmentation. Productivity accounting is a methodology which is used elsewhere to give additional insights into the productivity and pricing factors that drive the financial performance of a business. Miners know intuitively that productivity and pricing influence costs and profit, but only with productivity accounting can the dollars involved be calculated. Drilling and blasting are part of a chain of unit operations in a mine. For an owner-miner, drilling and blasting would be considered as cost centres and a productivity accounting cost model approach would be relevant. On the other hand a contractor is likely to consider drilling and blasting as a profit centre, in which case a productivity accounting profit model approach would be appropriate. Both of these will be explained. The paper provides a basic outline of deterministic productivity accounting and demonstrates its application to blasting. Drilling and blasting data from a mine was obtained for a two-month period. The change in productivity and prices was calculated to obtain the dollar contributions from them towards the change in cost. It was determined that although there had been productivity dollar gains these were offset by larger pricing dollar losses, the net effect being that total drilling and blasting costs increased. The productivity accounting analysis gives the facts and the mine is in a position to establish priorities based on knowing the dollar contributions of each input used.

Jan 1, 2001

Last September, when I was asked to prepare this paper, I was told the subject was "mining," a broad subject indeed! Rather than choose one of the many important technical and economic details which characterize mining today, I turned to a subject which fas- cinates me: mining's image. If we are to survive and prosper into the twenty-first century, and if industry and society are to continue enjoying the material benefits which flow from mining, we must address the melancholy fact that the general public at best does not understand mining, and at worst does not believe it is needed or deserves to continue. While my point of view is largely that of an American mining executive, I would hasten to point out that Homestake has participated in Australian mining for over three decades, and our subsidiary, Homestake Gold of Australia Limited, is now a major producer in this "lucky country." Does society need a viable minerals and metals industry? The answer is obviously "yes," so the challenge is to change some minds: not just those of the amorphous "public," but on a focussed basis targeting journalists, educators, TV commentators, politicians and opinion makers of all stripes (I thought of using "rifle shot" instead of focussed but thought that might be misconstrued). Along the way we miners must also look deeply into ourselves, our attitudes towards the society in which we function, and our willing- ness to change as well as to seek change in others. How did we become such bad guys? More than a century ago mining was not just accepted, it was even romanticised. In America, we had altered the time-honored concept of "Crown" lands into public lands made easily available to settlers pushing back the frontier. Miners even preceded the farmers and stockmen in what was perceived as nation-building, although by the 1890s there was a growing interest in conservation, especially the protection and management of forests and national parks. Even though emphasis was shifting toward government stewardship and away from trans- fer of public lands to private ownership, homesteading and mining were clearly recognised as valid uses requiring not just access, but security of tenure. Indeed, conservation as it was then understood implied management of the public domain as well as its protection. Initially this was no great problem to the U.S. mining industry, but as the nation grew and competing land uses became more important, conflicts began to appear, first over water rights and later over air quality and destructive mining practices. But these were local disputes rather than national issues, and two World Wars, the Great Depression and post-war reconstruction lulled our industry into thinking that nothing had really changed. After the storm began to break in the 1960s, the mining industry found itself confronted by a growing maze of complex and costly laws and regulations. It took us longer than it should have to realise that, in facing this challenge, we seemed to have lost the understanding and support of many of our legislators and a majority of the general public. For over 20 years now, since the first Earth Day in 1970, the U.S. Mining

Jan 1, 1991

By A G. Guinea

If you were reading this article in a newspaper or similar in the 1800s, you would know that the world was firmly in the grip of the Industrial Revolution. You might have been one of the families that decided that an agriculturally based existence was no longer for you, and that the promise of a factory job was more appealing and more secure. And it was. Financially at least. Not so much from a workplace safety perspective.

May 5, 2022

By Liu Wenyong, Huang Yucheng, Yang Ba

High-water rapid-solidifying material, called æhigh-water materialÆ, is a new material developed by the authors over many years. The material can solidify nine times its volume of water into solid. The material is a fine kind of binder with special properties. The solidifying body of high-water material with water has quite a high early strength. The compressive strength of the material within three days can reach the same strength as conventional Portland in 28 days. One ton of the material can replace three tons of conventional Portland cement as binder. Some important achievements have been made in application of high-water material. In metal mines, based on the material, a new full-tailing cemented backfill technology has been developed. The characteristic of the new technology is that high-water material is used as binder and full tailing or alluvial sand is used as backfill aggregate. Because of the application of the new technology, major technical problems in backfill technology such as classifying of tailing, dewatering, transportation of pulp, low strength of backfill body, environmental contamination and so on, have been solved.

Jan 1, 1998

By Jarvis ST

Colliery spoil is the major constituent of colliery spoil 'rockpaste' which has been used to infill abandoned limestone mines in the West Midlands of England since the early-1980s. The other constituents of rockpasle are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes onto consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising mulling a 6600 nt' section of an abandoned mine was conducted prior to the mulling of the Littleton Street Mine which had a volume of about 500 000 m'. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. This paper shows how a colliery spoil based paste has been successfully rued for infilling abandoned mine workings. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. To-date over I I mines with a total volume exceeding two million cubic metres have been backfilled.

Jan 1, 1998

By K George

The Dugald River lead-zinc-silver deposit is located approximately 60 km north-west of Cloncurry and 87 km north-east of Mount Isa. The development project is expected to turn operational in 2018. The resource is estimated to contain 61.1 Mt at 12.6 per cent zinc, 1.9 per cent lead and 34 g/t silver, with a projected mine life of 25 years. The evolution from exploration project to development project has presented multiple challenges for the technical team. Understanding and modelling the structural complexity of the deposit has been one of these challenges.Historically fault zones were logged as a lithology, with structural measurements recorded in a separate database table. When underground drill programs and development commenced in late 2012, it was recognised the deposit was more structurally complex than had been modelled. The extensive number of fault zone lithologies in core logging, made it difficult to identify fault trends and model faults in 3D software packages.In 2014, a structural project was conducted to produce a fault model for the deposit. The project highlighted that by logging the faults as a lithology, a shortage of fault characteristics was being recorded. Additionally, structural information could not be filtered to identify different fault sets due to the lack of information available to filter on. One of the major outcomes of the study was to change the methodology for the structural logging of drill core.Faults are now logged in a separate structural log. The structural log collects two types of information: interval data and point data. The interval data represents the damage zone of the fault in the surrounding rock and the point data the plane of movement for the fault. The faults are further characterised by their intensity on a scale of one to five, the type of fault structure (fault breccia, fault vein etc), the minerals present on the fault surface and structural measurements when available.The new data set allows fault data to be filtered based on fault characteristics, making implicit and explicit modelling of the faults more timely and accurate. The data set can be used to produce fault wireframes as single surfaces from the point data or hanging wall and footwall surfaces from the interval data. The logging method and how its applied in fault modelling form the focus of this paper.CITATION:George, K, 2017. A new approach to logging and modelling faults at the Dugald River Pb-Zn-Ag deposit, North West Queensland, in Proceedings Tenth International Mining Geology Conference 2017, pp 315–320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Pigdon SP, Anderson RM

The production of stabilised backfill at mine sites commonly uses Portland cement as the binder. Calcined gypsum has cementing properties and is cheaper to produce than cement. This paper discusses the strength of fills stabilised with calcined gypsum. Laboratory tests were carried out on specimens prepared from tailings obtained from four different sites to allow for the wide variety of tailings found in practice. The results show that the gypsum-based fills can achieve a strength of I MPa using around two and a half to four times the corresponding amount of cement.

Jan 1, 1998

By D Bruggemann, F Sereshki

There has been an ongoing research on coal and gas outburst for the past two decades at the School of Civil, Mining and Environmental Engineering, University of Wollongong. Research study began with a humble beginning, initially conducting basic laboratory studies on the coal and gas properties, progressing into the determination of gas content of coal by sorption technique and the effect of gas pressures on coal strength. The present laboratory facilities and research interests are extended to include the study of coal permeability and shrinkage properties and their effect of gas drainage characteristics with respect to gas type, and pressures. All the changes are examined with respect to changing in-site geological conditions of the coal deposit investigated. The aim is to provide a long-term support to industry in establishing a data bank for Australian coal deposit characteristics and properties.

Jan 1, 2005

By Ward M

The current and future requirements for an underground mine information management system are being met with a flexible, value-engineered approach to mine information/communication infrastructures. El-Equip has developed and delivered to over fifty mines around the world an integrated, high capacity, radio-based leaky feeder communication system called MultiCOM. To meet the requirements of recently developed advanced information management technologies, such as production and ventilation management, the system has evolved to support simultaneous mobile and fixed information delivery services over an integrated single cable system. The following paper will review how MultiCOM is enabling information/communications technology to cost-effectively implement mine monitoring and control applications. Applications described in this paper include mobile vehicle production tracking, vehicle location, ventilation system monitoring and control with integrated ventilation system simulation. The techniques described are leading the world in terms of flexible and value-engineered applications of technology in the underground mine.

Jan 1, 1995

Coal mining ceased at Strongman Mine this year after 70 years of production. Underground mining finished in 2003 and opencast methods began in 1998. During the life of the mine, 8 million tonnes of coal was extracted from two underground mines and 1.2 million tonnes removed through opencast methods. Strongman Mine is within the Grey Coal Fields; various seams have been extracted from the Rewanui Coal Measures. Coal extracted was predominantly of thermal or semi-soft specifications and characterised by low sulphur and low ash.   The area has steep topography, high rainfall (>3000 mm/yr) and is particularly exposed to westerly quarter winds. Strongman 1 and 2 underground mines are located in the steep, narrow valley which leads to the Strongman Opencast at the top of the valley. Subsidence from underground mining combined with spontaneous combustion, has resulted in an underground fire which has had substantial surface effects. Opencast mining in the steep topography resulted in several landslides at the perimeters of the site. These factors, along with water management, topsoil management and erosion control have added to the complexity of rehabilitating the site.   Rehabilitation of the site is well underway, including infrastructure removal, final landform creation and revegetation of the Strongman Opencast footprint (~45 hectares). Some innovative methods of rehabilitation have been trialled. Successful trials such as helicopter-seeding and moss hydro-seeding on highwalls are now routinely used along with traditional revegetation practices. 18 hectares disturbed land has been replanted with 88 000 seedlings, and another 200 000 seedlings are scheduled for planting over the three years. Fire management is an ongoing challenge; however thermal photography shows a steady decrease in hot areas which have been contained by grout curtains.   Mine closure is some time away and will occur after all standards set by Solid Energy and regulatory bodies are achieved.

Jan 1, 2006

The Sao Chico gold project is located on the Tocantinzinho trend which is the most mineralised zone in the Tapajos Mineral Field of Brazil (see Figure 1). The Tapajos goldfi eld was the site of the biggest gold rush in Brazilian history in the late 1970s and 1980s when approximately 500 000 garimpeiros (artisanal miners) rushed to the area to exploit extensive areas of newly discovered alluvial gold. Approximately 20 - 30 million ounces of gold were produced from these operations before the easily won alluvial gold deposits were largely depleted. The Tapajos region has had little exploration by modern exploration methods compared to any other equivalent gold fields in the world. The gold occurs in sulfide veins developed in shear zones within Proterozoic granites. Gold grades vary from approximately 15 g/t in the hard rock veins, to up to several ounces per tonne in the supergene weathered upper portions of the veins. Goldbearing vein zones in the weathered profile are free digging. In addition, tailings dumps from previous mining operations contain gold grades of approximately 1 g/t. Metallurgical test work conducted to date indicates that gold recoveries of at least 70 per cent can be achieved via gravity concentration. Gold Anomaly, via its 100 per cent owned Brazilian subsidiary, Gold Aura Do Brasil Mineracao Ltda (GOAB), plans to mine the tailings and weathered vein material by open cut methods to generate a quick cash fl ow and to provide a better understanding of the mineralisation as part of a feasibility study for mining the underlying sulfide zone mineralisation (see Figure 2). Mining will utilise locally hired excavators and trucks and ramp up to a rate of 100 tonnes per day. To treat the gold-bearing material, GOAB has purchased an integrated 'state of the art' gravity concentration processing plant from Gekko Systems of Australia. The processing plant includes a scrubber for clay and oversize removal, coarse gold gravity separation via an inline pressure jig and an inline spinner; and fine gold gravity separation via a Falcon Concentrator. The plant is expected to be operational by late 2010. This is an ABSTRACT ONLY. No paper was prepared for this presentation. 

Aug 1, 2010

By C J. Moran

Given that the mining industry is committed to sustainable development principles and that Australia is experiencing changes to the regulatory environment that aim to modernise the water sector and encourage adoption of consistent approaches, there is a well defined need for the Australian minerals industry to develop a water accounting framework. This requires: key terms and definitions for water metrics for use in the Australian minerals industry that is consistent with the wider water sector, a suite of metrics representing key components of an operationÆs water balance, a calculation method for some of the metrics, and a reporting protocol. This paper presents the methodology that was used to derive these four components. Existing accounting frameworks were reviewed and key terms and definitions that were consistent with current requirements were proposed. A calculation methodology was developed to obtain some of the key indicators and variables that cannot be easily measured directly (water loss through evaporation is an example). The adopted terms and definitions dictated model development, with the conclusion that a systems approach was the most effective calculation process. To test the proposed definitions and calculation methodology, values for water metrics were derived for eight sites. The proposed framework and definitions could deal with the specific situations selected as case studies. The associated calculation methodology produced complete accounts at various levels. Some elements of the accounts could be directly checked against available data and simulations. The framework captured well variations in the reuse efficiencies; reuse efficiency could even vary for similar processes. It is concluded that this preliminary accounting framework provides a consistent language and metrics for quantifying and communicating water management, both at the intersection of the site with the surrounding landscape (through detailed reporting of site inputs and outputs) and within operational activities. Using this consistent framework for quantifying and documenting water use within an operation will provide a platform for compiling and comparing minerals industry water use with other sectors. This may support benchmarking activities within regions or companies and help demonstrate leadership amongst water users in water resource stewardship. The approach presented here is applicable to a wide variety of mining and processing activities, and biophysical environments, and can be adopted as the first step towards developing national water accounts for the Australian Minerals Industry.

Jan 1, 2009

By R Hao

Uncertainties in large open pit geotechnical modelling has been a major concern for slope stability analysis. The level of confidence in the in-put assumptions, such as structural and rock mass model, dictates the modelling results to some extent. This article is to detail a case study of Kalgoorlie Consolidated Gold Mines (KCGM) regarding a predicted inter-ramp failure on an as-built pit walls by a 3D numerical modelling. Significant concerns were raised across site and multiple preventive plans were considered. After intense data collection work, it was confirmed that the risk of failure had been overestimated. The case study has improved the understanding of geotechnical data in-put and has enhanced the process of creating and updating geotechnical structural models at KCGM.

Jun 22, 2022

The Managalase area is remote and little visited by geologists or prospectors. Yet it holds the key to the tectonics and petrology of this part of Papua. The eastern Managalase plateau (M, Figure 1) lies between the Hydrographers andesite volcano (H) and Sesara shoshonite volcano (S) to the south of Popondetta on the Papua Peninsular. It contains over 30 small volcanic centres in an area of only 400 km2 . To the south and west lies the basic-utrabasic belt (B-UB) of the Morobe arc. This is the leading edge of oceanic plate obducted over the Owen Stanley Metamorphics during the lower Eocene time. To the east and southeast lies the Cape Vogel geosyncline where the western end of the Woodlark basin spreading centre enters mainland Papua. The extension of the spreading centre as a suture might pass as far as the southern margin of the Musa Coastal plain. A new pattern of plate tectonic motions has been determined by the global positioning system and the southern margin of the Woodlark plate has been redefined (Tregoning et al, 1998; Taylor, Goodliffe and Martinez, et al, 1999). The Managalase plateau is margined by two inferred faults. These outline a cusp protruding from the main basic-ultrabasic belt where these rocks are near the surface. The westerly arm of the cusp passes through the centres of the Hydrographers and Mount Lamington andesitic volcanoes. Mount Lamington overlies Quaternary alluvium and underlying Tertiary sediments (Arculus et al, 1983) but members of the basic-ultrabasic belt crop out on the southern flanks. The easterly arm of the cusp is an inferred shear zone (and ? fault) connecting up with the terminus of the suture on the Musa coastal plain. Movements on the two faults forming the cusp are thought to have produced the conjugate N-S, E-W faults on the plateau (Ruxton, 1966). To the east, and isolated, are the two large andesitic stratovolcanoes of Mounts Victory (V) and Trafalgar (T) which together form Cape Nelson. Mount Victory was last active in the 1890s. The Waiowa shoshonitic volcano explosion centres (W), last active in 1943 - 1944, lie near the suture adjacent to the actively rising Goropu mountains. Extension in these mountains is clearly demonstrated by the soil profiles being skeletal along a bounding fault and ageing uphill. The incision of small parallel ravines also dig deeper further upslope from the fault. To the south-east of Mount Suckling (K) the Dayman Dome is also an expanding mass. The Owen Stanley fault is parallel, and located to the south of the suture. The Mesozoic metamorphics form the backbone of the Papuan Peninsula. The intramontane Musa Trough is thought to date from the mid-Tertiary. At the eastern end of the trough Pleistocene and Recent ultrabasic breccias and alkali basalt crop out (Green, 1961).

Jan 1, 1999

By T A. J Hopper, S Mukkisa, K-O Ott, D Palmer

RIG Technologies has developed new technology that can successfully acquire high quality natural gamma ray (GR) and hole deviations, downhole while drilling, on reverse circulation drills. This technology survives the hostile downhole environment with shocks of between 400–2500 g for 7– 10 days at a time. The Logging While Drilling (LWD) service eliminates the need to run in-rod surveys, either by the driller or by wireline trucks and crews. This time saving is in the middle of the drilling process, thus enabling drills to keep drilling and increase their productivity. Additional to the natural GR and directional survey, the downhole tool is equipped with sensors to measure the downhole dynamic response of the drilling system providing insights into rock hardness, density and potentially clay types. These parameters have never been acquired behind the hammer before and coupled with surface measurements from the drills themselves, form a rich data set for trainable machine learning algorithms shortening the time to receive advanced geophysical answer products from sometimes months, to live feeds directly from drills (Hopper, 2019). Alive, high speed, two-way data link between surface data acquisition systems and downhole geophysics tools has been established and incorporates calibrated surface measurements of dynamic forces directly on the drill string to match up with those measured downhole. Receiving live streams of natural GR and hole deviation surveys as the drill is drilling allows true remote decisionmaking with live data available anywhere in the world. The combined data from surface and downhole dynamics builds a data set that could begin to enable true optimisation of autonomous drilling processes.

Nov 8, 2021