Search Documents

By J Ledgerwood

Namakwa Sands is a mineral processing company based on the West Coast of South Africa and is solely owned by Exxaro Resources Limited. Mineral ore is mined and processed, concentrated and both chemical and mechanically upgraded before being sent for electrostatic and magnetic separation units. The final high value mineral products report as Zircon, Rutile and Ilmenite.The recovery of non-magnetic material is largely dependent upon a number of factors, including but not limited to dew point, ambient temperature, feed rate, mineral size distribution, specific gravity and mineral content in head feed. One important limiting factor to recovery in typical dry mill operations is the particle size distribution of the feed. Variance in the particle size has catastrophic consequences for recovery. This is the reason for this study. Until recently large variances in non-magnetic production were viewed to be a function of machine operation. This view was later rejected with the feed size distribution determined as the major driver of low recoveries, for Namakwa Sands orebody 50 per cent variance in particle size distribution can be noticed within one day. This is because of the successive mining blending techniques employed.The predicament is that the two modes were so closely placed together that recovery of a single mode is almost impossible without the consequence of greatly reducing recovery. The second mode was found at 125 µm while the first was at 90 µm. Interestingly, for the mentioned feed type a cumulative size distribution of a unimodal feed type is almost exactly the same as for a bimodal size distribution. Thus a plot of cumulative size distribution will show no difference due to the modes being so close together. This is the reason why this phenomenon was not noticed before.The study also found that, using an high tension roll (HTR) or rare earth roll, a fine stream with a single mode at 90 µm versus a coarse stream with a single mode at 150 µm would yield completely different results interms of yields. Larger conductive particles are thrown from the roll while small particles loose charge faster (entrainment). Results in terms of the bimodal size distribution show that even though 25 per cent of the feed type is greater than 150 µm the yields followed a similar pattern to that of the coarse particles rather than that of the majority (75 per cent) fine particles. This confirms what was published by M Ziemski and P N Holtham in 2005 on charge decay rates; they mentioned that particle bed effects played a major role in recovery.

Oct 5, 2011

By L O. Filippov, A Piçarra, I V. Filippova, N P. Lima, K Silva

The reverse cationic flotation using the starch as depressor of iron oxides is the most efficient upgrading process when is applied to the simple systems composed by hematite/magnetite and quartz. The fundamental studies performed with iron ore samples from different deposits over the world (Brazil, Russia, Mexico) confirmed the inefficiency of starch when the silica content in the concentrate is controlled by Fe/Mg-bearing minerals. The main approaches for solving these issues focused on using new collector formulations or new depressants. However, the alternative depressants tested inhibited flotation of quartz or were less efficient as iron oxide depressant. In this work, a comparison between new amidoamine collector with conventionally used etheramine and oleate collectors in the flotation of pure minerals and actual iron ore samples was performed. The electrophoretic mobility, contact angle and infrared spectroscopy measurements allowed to deduce the hindrance effect as main mechanism of selective adsorption of the amidoamine on the quartz surface compared to hematite and kaolinite. Molecular modelling studies revealed that this steric hindrance effect can be explained by the combination of the "shield" formed by the coordinating water molecules on the (001)-D2 hematite surface and the large volume of the amidoamine head group. The amidoamine tested as collector without use of a depressant showed excellent flotation selectivity allowing the total flotation of quartz from a mixture with hematite. High collector performance and selectivity were confirmed during reverse flotation of quartz using continuous flotation column (D = 500 mm; H = 4000 mm) and allowed to produce the iron concentrates with more than 60 per cent of iron from the rejected slimes samples of Vargem Grande 2 processing plant (Iron Quadrangle, MG, Brazil). The new collector allowed to develop flexible flotation flow sheets to process the iron ore with a complex gangue mineralogy and unlock the old altered tailings and slimes product as new resources

Aug 24, 2022

By M Brady, O Salisbury, C Claassen, B Beamish, H Baxter

Monitoring for signs of elevated spontaneous combustion in the active goaf behind the longwall face is crucial for early intervention of any potential heating incidents. Typically, trigger action response plans (TARPs) are established at the start of longwall mining and often are only reviewed when triggers are activated frequently and become ‘nuisance alarms’, or in the worst case scenario after a heating event. Narrabri Mine has adopted a proactive approach of reviewing the longwall active goaf spontaneous combustion monitoring TARP at the commencement of each longwall block and prior to reaching a known ‘mylonite zone’ of crushed coal, which is associated with increased coal oxidation. The review is based on information recorded from the monitoring data of the previous longwall blocks as well as interpretation of relevant spontaneous combustion propensity results for the coal. This has resulted in the mine implementing a zoned TARP approach for each longwall block covering both the longwall retreat through normal undisturbed coal and the zone where the goaf is influenced by the increased coal oxidation associated with the mylonite coal. The consequence of this approach is that it has removed the issue of having nuisance triggers being activated during mining through a known increased oxidation zone, while maintaining a high awareness of indicators of spontaneous combustion.CITATION:Baxter, H, Claassen, C, Salisbury, O, Brady, M and Beamish, B, 2015. Implementation of a zoned trigger action response plan associated with changing mine conditions at Narrabri Mine, in Proceedings The Australian Mine Ventilation Conference, pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D Clarke, I Minniakhmetov

The Olympic Dam deposit is truly a world-class IOCG-Ag deposit, the world’s fourth largest deposit of copper and the world’s largest known single uranium deposit. Traditional and non-traditional methods have been used to accurately model the geology and mineralisation of the Olympic Dam deposit. Conditional simulation models have long been used as the most robust method for estimating risk and uncertainty in mine planning decisions at other mines around Australia and the world. There are many challenges associated with simulating the Olympic Dam deposit at a selective mining unit size sufficient for underground mine planning purposes. These include the size of the deposit, resulting in hundreds of millions of grid blocks; the disseminated nature of the zoned sulfide mineralisation. And lastly the direct relationship of the relative abundances of the sulfide mineral species that are crucial to the Olympic Dam smelter performance. Several geostatistical techniques have been utilised in the workflow for the Olympic Dam Conditional Simulation model to address these challenges. The key techniques are: • Projection Pursuit Multivariate Transform to de-correlate the main elements before simulation. • Pluri-Gaussian implicit boundary simulation method to simulate the mineralisation domains. • Spectral simulation method of de-trended and de-correlated attributes with account of local varying variance. The resulting conditional simulation models have been validated against histograms, grade-tonnage curves, cross-plots and assessed for variogram reproduction. This paper presents how the final conditional simulation models compare to benchmarking models created using alternate estimation techniques of ordinary kriging and local uniform conditioning. It also presents a validation process using historical samples to test final estimate accuracy of the simulation models.

May 24, 2023

By H Hoogvliet

The Goondicum Crater industrial minerals deposit is located about 30 km east of Monto, Central Queensland, Australia. Early exploration programs in the 1990s found alluvial ilmenite along the banks of the Burnett River. This mineralisation was traced upstream to the Goondicum Crater. The Goondicum Crater is a topographic feature centred on a roughly circular 6 km diameter layered gabbro complex. Significant ilmenite, apatite, titano-magnetite and feldspar mineralisation are present in a weathered horizon up to 25 m thick. After several drilling campaigns in the Crater and subsequent feasibility studies, the project was developed by Monto Minerals Ltd, an ASX listed company, in 2007. However, the project never achieved production performance expectations and ran out of commissioning funds. The company subsequently went into voluntary administration in August 2008.In 2009, the RMM Capital group, of Brisbane, took control of Monto Resources Pty Ltd, and renamed the company Belridge Enterprises Pty Ltd (Belridge). Belridge commissioned a redevelopment study aimed at recommencing mining and processing operations. As part of the redevelopment study the authors planned a drilling campaign, managed a quality control program and developed a block model. This paper describes the drilling program, analytical procedures, quality control procedures and the preparation of the block model.The block model for the resource estimate was created using 1 m high blocks, wireframes defining the main material types, and 2.5 m thick horizontal search ellipsoids with a radial pattern. The deposit was ‘flattened’ prior to modelling. To assist with the economic evaluation of the project, each block in the model was assigned a net dollar value based on economic parameters provided by Belridge, including anticipated revenues and costs. This modelling technique allowed for efficient investigation of various scenarios and was used extensively in the development and optimisation of the project’s financial model. At a zero net value per block, comparable to a break-even cut-off grade of four per cent ilmenite equivalent, the Indicated plus Measured resource is estimated at 51 Mt, averaging 4.1 per cent ilmenite, 1.9 per cent apatite and 2.5 per cent titano-magnetite.

Oct 5, 2011

The man in the street (and no doubt most members of the Institute) thinks of wire, if he gives it any thought at all, as a most commonplace commodity. It is an accepted necessity, and like most necessities is taken for granted, unless a shortage in one or other of its multitudinous forms or products causes inconvenience.For many years Australia has ·been a large consumer of wire, particularly for fencing. With the rapid development of secondary industry the demand has increased in both size and character until at the present time much of the wire produced in this country is used as raw material for subsequent manufacturing processes. The call has been of so varied a nature that the Newcastle Wire Mills now turn out a greater variety of wire types than any other single plant in the world.In this paper, the aim is to provide a picture of the manufacturing, properties, and uses of wire. No attempt is made to cover the subject in any detail, as the field is much too broad for anything other than general treatment. Many phases, particularly in regard to manufacturing processes, are, therefore, dealt with cursorily, but it is hoped that the paper will, without delving too deeply into the technical aspects of Wire production, give a general appreciation of:- (a) How steel wire is made. (b) The remarkable physical characteristics obtained by judicious combination of chemical composition, heat treatment, and subsequent cold work. (c) The uses of steel wire.HISTORY.Best known of the early references to wire is that appearing in Exodus, where mention is made of gold wire being used for the sacerdotal robes of Aaron. However, the period in question, about B.O. 1491, is comparatively modern history as far as wire is concerned, for specimens believed to have been made about B.O. 4600 have been found. It is fairly certain that the Egyptians produced iron wire in B.O. 4000. Of particular interest is the

Jan 1, 1947

By E de Necker, F D. I Hodg, L-M Cruywagen

The acid mine drainage (AMD) situation at three opencast collieries in the Witbank Coalfield, South Africa, was evaluated from different perspectives. Twenty-seven test pits were dug into the spoils of these collieries to characterise the in situ conditions of spoils of varying age. Detailed static testing was done on surrounding drill holes and additional samples were taken from the test pits. Selected samples were tested using different techniques, namely ABA, mineralogy and kinetic tests. Groundwater monitoring boreholes from the areas surrounding these spoils were also used for characterisation. The ABA results compared favourably with the in situ determinations; acidic test pits proved to be potentially acid-generating from ABA, even when the samples had neutral paste pH. Kinetic test results showed these samples to yield low pH leachate over the test period. In several of these results, the theoretical depletion of neutralising potential and the onset of acidity were well matched. NAG pH-values and final observed water chemistry corresponded for the cells predicted by ABA to acidify, but compared poorly in cells that did not acidify. Results from the non-acidic spoils were consistent with the in situ observations. Alternative kinetic test methodologies were also employed. Duplicate samples were tested in humidity cells and in aerated trays that were manually wetted on a regular basis. Results from these tests showed an excellent correlation. Detailed mineralogical determinations using XRD and XRF were used for comparison to the ABA and, in some cases, humidity cell results. These comparisons show that the ABA results are consistent with the results expected from the mineralogy. The conclusion from these assessments is that ABA, in most cases, provides information that can be correlated to the field, mineralogy and to humidity cells. The use of multiple techniques leads to a higher degree of confidence in the use of the data.

Jan 1, 2003

The cost of power is an important matter to mining companies generally and this thought that the members of the Australasian Institute of Mining Engineers, as well as the engineering and mining professions generally would be interested in any proposal for the reduction of that cost-has led to the presentation of this paper.The writer trusts that the description will be found clear and increase the interest in this exceedingly interesting subject. In the working up of the electrical arrangements touched on in this paper, the author has had the able assistance of hisfriend Mr. F. J. Mars, to whom he offers his hearty thanks. The selection of the best class of power plant for a mine is a very difficult and large problem and it is quite out of place to dogmatise that anyone of the many systems that offer isbetter than another, eg that the all electrical is better than the partly direct steam-driven and partly electrical, or that a gas plant is better than a steam plant.Such a selection is one that calls for very careful and close consideration, in each particular case, of a large number of regulating factors before it is possible to arrive at a proper decision.

Jan 1, 1911

By B Jones, M Chappell

Installing ground support correctly is not an easy task, whether lack of operator training, poor ground conditions or underperforming equipment. Confirming the quality of installation can help with planning and remedial works and help to maintain a safe working environment. A 2?m bolt with 700?mm of encapsulation will pass a 10?t pull test (assuming ground conditions permit); however, it will not provide any data of the unencapsulated length and thus the ability to withstand corrosion. Complimentary testing in the form of non-destructive testing (NDT) can provide factual data that leads to the assessment of the quality of the encapsulation. By improving the quality of the encapsulation, the risk of corrosion is reduced, the ground support durability is improved and hence the asset life is enhanced.This paper presents a case study of a trial using the NDT system RokTel™. Installations of varying quality were installed and tested. The characteristics tested were corrosion, load and free length. These characteristics can be tested and assessed for cable bolts, thread bar bolts and split sets. The aim of this paper is to present NDT testing as a viable method for assessing installation quality and ongoing performance of the ground support.CITATION:Jones, B and Chappell, M, 2014. A non-destructive testing method for measuring bolt condition, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J Herd, J Rowe, M Cutbush, d F. Aziz

WearApp provides expertise for assessing the degradation of removable screening media panels on vibrating screens right in a user’s pocket. Through the WearApp application, users can simply take a picture of a panel using their mobile, enter some basic information and have the application assess the wear to provide a recommendation for whether the panel needs to be replaced. Where traditional mechanisms for assessing panel wear only measure a few points across the panel face and rely on having personnel with specialised knowledge available to perform the assessment, WearApp uses deep learning models to analyse the entire panel face and support the user to make an informed decision. The application works through analysing a panel image and using a model to automatically detect the corners of the panel. Given the known dimensions of the panel, this enables the application to calibrate the pixel size against a known reference. A second set of models then detect the apertures and measure their dimensions. With the aperture dimensions defined the application assesses the wear of the panel through referencing a stored 3D model of the aperture. Finally, the data from each aperture is collated and the wear of the entire panel face defined. Since WearApp performs measurement of the entire panel face, it also allows the user to perform a more detailed analysis of the panel’s wear profile. Where typically, the panel wear is only measured in a few locations, WearApp’s analysis enables users to visualise the panel wear across the entire panel face, identifying areas of high wear that could be leading to premature panel replacement. Additionally, because the entire panel face is measured the change in screening efficiency can be calculated accurately for the worn panel, even taking into account the impact of aperture pegging by small rocks.

Sep 1, 2024

By D Mather, H R. Asche

"In the civil tunnelling field, the use of tunnel boring machines (TBM) has now overtaken the use of conventional excavation methods (drill and blast / roadheader). This is due to a number of reasons, including the increasing availability and reliability of TBMs, the ability to deal with a wider range of face conditions, and the reduced excavation cost that TBMs can bring.Mining companies have spearheaded the advances in shaft boring by mechanised means, both in blind and raise boring. However, mining companies have been slower to adopt mechanised tunnelling.When contrasted with a conventional mining contract, there are good reasons why TBMs in mining applications are relatively rare. A conventional decline contract may have very little geotechnical information. The decline alignment can be subject to change as the tunnelling progresses. The infrastructure requirements are less for a conventional decline, and the sunk cost prior to excavation commencing is lower. Contract documents can be very simple.The history of TBM use in mining is reviewed and lessons are described. From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.We believe that despite the additional requirements for TBM declines, the cost and time advantage to mining companies is very attractive. The challenge is to recognise and to meet the requirements for success in a TBM drive to achieve the advantages of: faster advance rates reduced rock damage/overbreak reduced support requirements uniform muck characteristics greater personnel safety.From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.CITATION:Asche, H R and Mather, D, 2014. Use of ?tunnel boring machines in the mine environment, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 655–662 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014

By M J. Thurley, L Lindqvist, D Degerfeldt, J Nyström, R Nordenskjöld

Rock breakage is a major component of all mining and mineral processing operations with the particle size distribution linked to productivity through the comminution chain. Optimisation and automatic control of comminution, material handling, and agglomeration processes is a complex task with large potential for gains in productivity, and energy efficiency. A key factor in realising these gains is the requirement for fully-automated online particle size distribution measurement to provide the necessary feedback and input for control. Moreover, to enable automatic control system it is necessary to provide a consistent, reliable size distribution measurement that avoids the significant errors resulting from under-sizing overlapped particles and over-sizing clusters of fine particles. Published literature and observation of commercial systems indicate a body of predominantly 2D photographic based particle size measurement systems that suffer from a number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited colour variation in the material. In order to overcome these limitations a university and industry collaboration developed three-dimensional particle measurement (3DPM) between 2006 and 2012, based on 3D surface profile measurement of the visible material on conveyor. 3DPM avoids particle delineation errors due to variation in material colour and shadows, detects overlapping versus non-overlapping particles, and identifies areas of fine particles as fines and not large rocks. 3DPM measures: the visible material and calculates its particle size distribution, bulk volume, detects boulders, and conveyor belt fill factor in an automated consistent manner. Furthermore, 3DPM’s advanced algorithms allow observation of particle variation that would otherwise be undetected without the capacity to identify visible areas-of-fines and overlapped particles. Boliden Mines has installed 3DPM at three operations for measurement between the stockpile silo and grinding mill, and measurement after the primary crusher. Fragmentation measurements across multiple years of measurement are presented with some observations of plant behaviour. In the future 3DPM results will be incorporated into automatic control strategies for plant optimisation. 3DPM is used across a wide range of material types and applications that also includes; limestone aggregate for quality control in manufacturing, agglomerates for closed-loop automatic control in chemical production, and measurement of coke for size-based blending feed control to the blast furnace in steel production. CITATION:Thurley, M J, Degerfeldt, D, Nyström, J, Nordenskjöld, R and Lindqvist, L, 2018. Automated, online measurement of bulk material size distribution on conveyor using 3D profile imaging at Boliden Mines, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 641–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By P Myers, T Elkington, S Wonday

Sierra Rutile LimitedÆs (SRL) heavy mineral sand mining operation in Sierra Leone, West Africa, is embarking on a new phase of its life. After confronting many challenges during the 1990s and 2000s, SRL is embarking on a strategy of growth to recover maximum value from the mine over the rest of its life. Sophisticated linear programming techniques have been used to develop an optimum strategy for extracting SRLÆs many known deposits of economic grade, while considering options for expansion and for a variety of mining and processing methods and combinations. CITATION:Myers, P, Elkington, T and Wonday, S, 2012. Strategic optimisation at Sierra Rutile - A case study in maximising project value, in Proceedings Project Evaluation 2012 , pp 59-66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By Osorio J. D C, McMahon M. D

Burwood Beach Sewage Ocean Outfall is being constructed by the Hunter District Water Board as part of an amplification scheme to eliminate pollution from adjacent bathing beaches. The outfall consists of a 93m vertical shaft, 1950m of 2.7m diameter tunnel with a series of diffuser outlets connecting the seaward end of the tunnel to the sea floor on a rock outcrop. The site of the work is in the Newcastle Coal Measures and the project is complicated by the proximity of colliery workings to tunnel alignment, although the colliery records provided valuable information on geological features. The location of the tunnel was determined to be in the Waratah Sandstone Formation immediately below the colliery workings after three different alternatives were considered. The shaft, which will be sized to suit contractor's construction methods and equipment, will be sunk through about 24.5m of alluvial material and 68.5m of rock. The tender documents were developed to allow the contractor considerable flexibility in construction method to suit available equipment. The specification also allowed great flexibility in tunnel construction method with minimum cross sectional area of 5.7m2 being the basis for a number of allowable alternative profiles ranging from circular to horseshoe.

Jan 1, 1987

By P Collier

From 1972 until 1989 when operations were suspended Bougainville Copper Limited (BCL, owned 53.58 per cent by Rio Tinto Limited) operated a large open pit mine and processing facility at Panguna on Bougainville Island, Papua New Guinea producing copper concentrate containing significant quantities of gold and silver.BCL has a stated vision of recommencing operations at Panguna. In 2008, Rio Tinto, on behalf of BCL, conducted a multi-disciplinary study to assess the technical and financial viability of redeveloping the Panguna operation. One of the key outputs of the study was a Joint Ore Reserves Committee (JORC) Code compliant mineral resource statement based on the existing block model and fundamental data, archived since mine closure. Historical data (including the resource block model and drill hole data) was recovered from computer archives by a former Panguna mine employee familiar with the various obsolete data formats, thus maintaining an unbroken chain of custody of the data by Rio Tinto since operations were suspended. No additional data were collected as part of this study.The extensive data and documentation archive facilitated a sufficiently detailed evaluation of the fundamental data and model to support an updated resource statement. Table 1 of the JORC Code was used to guide the model validation process.Reconciliation of blasthole and metallurgical plant data with the reserve model, indicated that the copper and gold drill hole composite database was significantly biased towards underestimation in several key domains due to a combination of the following: mineralisation loss during core loss, core loss (minor), vertical drill holes failing to intersect sufficient subvertical mineralised fractures and veins, drill hole spacing too wide, and variable diamond drill hole core size. The resource model evaluation was based on three material types (all previously mined at Panguna), that were defined based on cut-off grade and rock type parameters: direct feed ore – material for delivery directly to the plant, preconcentration and screening ore – subeconomic material beneficiated to produce fines of economic grade, and waste. Three pit shells and designs were generated based on three separate sets of economic parameters. These economic parameters were also used to assign material types to the block model. The three resulting models were then evaluated against the corresponding pit shells.Classification of the resource was approached conservatively due to the inherent bias in the drill hole data. Consequently only Indicated and Inferred resources were tabulated.The study highlighted the importance of maintaining detailed documentation pertaining to resource estimates and operational history, particularly reconciliation, and the value that can be added by a simple, low-cost data compilation exercise.

Aug 22, 2011

At its Port Kembla Plant, Australian Fertilizers Ltd. manufactures Superphosphate and other Phosphatic Fertilizers.Phosphate Rock is received from Nauru and Ocean Island. It contains water insoluble tri-calcium phosphate, Ca3(PO4), to an average of about 86%.It is crushed to pass a 20-mesh x 26-gauge woven wire screen, and is then treated with Sulphuric Acid to give the product Superphosphate with a water solubie prosphate content of 20.5%, estimated as P205. Sulphuric Acid is made by the chamber process. Three sets of chambers are installed, on,e five-chamber set of timber frame work construction and the other two of more recent date, each with four chambers of steel frame work construction. A fourth chamber set is now being built.Sulphuric Acid is delivered for use. at about 70% H2S04, the strength depending upon the rock used.Mixing - The crushed rock and sulphuric acid are mixed in weighed and measured proportions respectiyely in one-ton batches in revolving cast fron pans, mechanically stirred. The mixture, while still slurry, is run into a closed horizontal concrete cylinder (den) where, with the completion of the chemical reaction, it rapidly sets as Superphosphate.Approximately fifty batches are required to fill a den. When full, the den is opened ana the mass cut out by a revolving cutter. The product is elevated and conveyed to any required position in the Superphosphate storage shed, where it dries and matures.Despatch - As required, the Superphosphate is excavated by a two ton grab and conveyed from the matured "dump" to bagging units where it is disintegrated, screened and bagged at twelve bags to the ton. The filled !Jags are closed by machine and delivered to railway trucks immediately.Mixed Fertilizers - Sulphate of Ammonia, Sulphate and Muriate, of Potash, and Blood and Bone are mixed with Superphosphate and thoroughly incorporated to give different mixtures to meet special plant requirements.

Jan 1, 1938

By D Timms

The Kempfield deposit is located in the Hill End Trough, one of several intracratonic basins developed during Silurian–Devonian time, in the eastern province of the Lachlan Orogen, Eastern Australia.The deposit contains an oxide resource of 5.8 Mt @ 58 g/t Ag and a sulfide resource of 14.4 Mt @ 45 g/t Ag, 1.7 per cent Zn and 0.6 per cent Pb, classified and reported in compliance with the JORC Code. The deposit has been previously explored by a number of companies, including INCO, Shell, Jones Mining, Golden Cross Resources and recently Argent Minerals Ltd (Argent). Argent is currently completing a definitive feasibility study with a view to mining the deposit.The deposit is hosted at the boundary between the Molong High to the west, comprising Ordovician sediments and volcanic rocks and the Hill End Trough to the east, interpreted as a back-arc basin containing Silurian sediments and siliceous-feldspathic volcanic rocks. The boundary between these two strato tectonic units is an imbricate thrust fault zone known as the Copperhannia Thrust.The Kempfield deposit is hosted in felsic volcanic rocks known as the Kangaloolah Volcanics. These have been in-faulted and folded into the Middle Ordovician meta-sediments of the Coombing Formation of metasediments along the Copperhannia Thrust. The Kangaloolah Volcanics belong to the Late Silurian Mumbil Group, comprising submarine carbonate-shale facies interspersed with extensive felsic volcanic piles, which grade conformably upwards into turbiditic sandstone and siltstone sequences (interpreted to represent a deeper depositional environment). These turbiditic rocks are known as the Campbells Formation, comprising siltstone, sandstone and andesitic tuff. The rocks at Kempfield are metamorphosed to lower greenschist facies, reflected through the different type of schists.Silver, gold, lead, zinc mineralisation is hosted in barite-rich horizons, near the boundary to quartz-phyric tuffaceous rocks in submarine, immature, reworked felsic ash tuffs. Barite appears to be hosted in greatest concentrations by the coarser grained volcanoclastic sandstones and grits, whilst intercalated siltstones are volumetrically minor and tend to return low barite and silver. Mineralisation is hosted in stratiform and probably stratabound barite-rich horizons. A northeast-trending, steeply dipping, metamorphic cleavage (S1) occurs throughout the project area.

Aug 22, 2011

By D M. Brady

Underground coal mines in Australia have embraced the use of various inertisation techniques both proactively and reactively. The use of such techniques can have a significant influence on ratios and trends used to monitor the status of the underground environment. Whilst control strategies should never be ignored in favour of preserving the integrity of ratios, the influence and significance of the changes likely to be seen should be anticipated and understood for reliable interpretation of the situation. This paper looks at the influence inertisation techniques can have on results and subsequent interpretation.CITATION:Brady, D M, 2013. The influence of inertisation techniques on gas interpretation, in Proceedings The Australian Mine Ventilation Conference , pp 259-264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By R Schmitt, Y Ghorbani, I McElroy, N J. Bolin, M Parian

Aitik is a large copper porphyry type deposit located in northern Sweden, currently exploited at an annual rate of approximately 45 Mt. The ore’s exceptionally low head grade of 0.25 per cent Cu and varying degrees of hardness across the entire deposit pose challenges to the two fully autogenous grinding lines, each of which comprises a primary autogenous mill in series with a pebble mill. The variability in ore grindability frequently leads to fluctuations in mill throughput. Within the framework of a geometallurgical approach, the present study investigated the relationships between ore grindability and modal mineralogy. For this purpose, drill core samples from different lithologies were subjected to Boliden AB’s in-house grindability tests. This fully autogenous laboratory-scale test generates a grindability index mainly related to abrasion breakage, which is a significant breakage mechanism within autogenous mills. The test results suggested divergent degrees of grindability within and across the selected rock types. A combination of scanning electron microscopy, X-ray powder diffraction, and X-ray fluorescence analyses was performed for the grinding products and bulk mineral samples. The resulting mineralogical and elemental properties were subsequently correlated to the parameters from the grindability tests. It was shown that the main mineral phases, such as plagioclase, quartz, and micas, correlate well with the grindability indices. Similar correlations were found regarding the sample’s chemical composition, attributable to the main mineral phases. A further inverse correlation was established between the sample’s calculated average Mohs hardness and the grindability indices. Moreover, mineral liberation information provided by scanning electron microscopy was associated with the parameters mentioned earlier. The identified relationships between grindability, modal mineralogy, and element grades may help Boliden develop a predictive throughput model for Aitik based on the mine’s block model.

Aug 24, 2022

By Y Xie, L O’Connor, S C. Dominy

"Sheeted vein gold deposits are characterised by multiple subparallel veins and free milling gold. In situ heterogeneity of mineralisation results in grade and process parameter variability, which will increase project risk. Measured variability is often enhanced by poorly designed sampling and test work protocols. Protocols that are optimised within the framework of the theory of sampling to suit the ore type, together with quality assurance/quality control systems, will reduce variability and provide fit-for-purpose results. The geometallurgical approach requires spatially distributed samples within a deposit to support variability modelling. Diverse attributes from core logging, mineralogical/textural determination and small-scale tests are used to measure variability. This contribution emphasises early stage geometallurgical intervention during project development. It presents a discussion of representative sampling in the context of the theory of sampling. A case study presents a protocol that exemplifies how data can be gained from a well-designed and planned program to support a resource estimate and prefeasibility study.CITATION:Dominy, S C, O’Connor, L and Xie, Y, 2016. Sampling and Test Work Protocol Development for Geometallurgical Characterisation of a Sheeted Vein Gold Deposit, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 97–112 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016