Search Documents

By M Sandy, P Bamford

The Challenger Gold deposit was discovered in 1995 by Dominion Mining Ltd in a remote western area of the Gawler Craton in South Australia. Mine development commenced in 2002 with initial production from an open pit supplemented by ore from a very small adjacent auxiliary pit. Development of the underground mine commenced in 2004. The orebody plunge of just less than 30 degrees requires careful attention to mine design. Production from the M1 orebody, with less than 800 ounces per vertical metre (ovm) and very limited æsurgeÆ capacity, requires careful scheduling and implementation to ensure continuity of ore feed for milling. Initial production results from underground stopes included more dilution than anticipated. The narrow, high-grade zones proved to have much more complex geometry than early interpretations had indicated. Greatly improved understanding of the mineralisation controls resulted in important changes being made to the underground mine design and method. Coupled with careful control of development and drilling and blasting practices, this resulted in an immediate reduction in dilution and high recoveries of the resource. The benefits of these changes flowed through in the 2005/06 financial year, resulting in a 150 per cent increase in gold production to 108 080 oz and a sharp reduction in cash operating costs to A$280/oz. This was followed in 2006/07 with production of 108 91 oz of gold at an operating cost of $309/oz and in 2007/08 with 109 326 oz of gold at $367/oz. Production to June 2008 has been mainly from the M1 orebody, with the lowest stoping to date on the 580 m Level (615 m below surface) above development mining on the 520 Level. The rate of vertical advance of mining this orebody has averaged 150 vertical metres per year. The increased current combined JORC compliant resource and reserve position of over one million ounces, now includes the M2 and M3 orebodies with a current total average gold inventory up to 1400 - 1500 ovm. Exploration has intersected other shoots and all shoots are open at depth. The adjacent M2 and M3 orebodies are being developed for stoping. The narrow width of these zones from 1 m up to 4 m will require continued focus on ore zone definition, accurate development and careful drill and blast practice. In addition, to minimise cost increases in the current period of rapidly escalating labour, equipment, consumables and energy costs, high productivities will need to be maintained to allow the established rapid mining advance to continue at low unit costs.

Jan 1, 2008

By A B. Bayooke, A C. Robertson

In terms of underground tunnelling in metres advance per capita, Australasia compares well with the best world performers. This is because of the large number of metalliferous mines, coalmines and civil tunnelling projects, with the Australian tunnel advance for civil and mining projects exceeding 625?km/a. In terms of hard rock quarry extraction, Australia produces approximately 200?Mt/a of aggregates, roadbase, fill material and specialist rock products from its quarries, which equates to approximately 8?t/capita. Australian mining and tunnelling contractors are also of world standard and are used to excavating in a variable range of ground conditions in a competitive environment. One author has been involved in tunnel and underground space planning and quarrying in Australia for the past 25 years and predicts that, over the next 20 years, there will be a major swing towards underground space for commercial uses. This paper identifies the potential uses of underground commercial excavation and the planning and geotechnical challenges for the future. Underground quarrying creates new opportunities to extend existing quarries within their urban footprint with minimum impact on the surrounding community. Investigations by the authors reveal that there are very few cities in the world that actually incorporate underground space planning in their city plans. However, cities such as Helsinki have been planned in detail to utilise the rock resources beneath them. Brisbane is used as a case study for a practical application of commercial underground space and underground quarrying in Australia.CITATION:Bayooke, A B and Robertson, A C, 2014. Geotechnical challenges for underground commercial space and quarrying in Australia, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 317–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D Veneziano, J Van Dyck, R Snow, W Pytel, O Zanoli

Best practice standards generally recommend assessment of the environmental and societal risks posed by tailings storage facilities, but they rarely specify how the analysis should be made. As a case study, this paper describes a safety assessment of the Zelazny Most tailings pond operated by the Hydrotechnical Unit of KGHM Polska Miedz SA in Poland. The complete assessment includes a failure mode effect criticality analysis (FMECA) that considers all conceivable failure modes, but this paper focuses on one key mode, the loss of stability during the planned raising of the crest above its current level. Reliability against static dam failure considers uncertainty on the safety factor in a limit equilibrium approach. The threat of dynamic (earthquake induced) instability is assessed by developing a model of future seismicity as a function of the mining plan and considering uncertainty on the induced permanent displacements along critical sliding surfaces. We quantify the additional level of protection against outflow provided by the beach using an event tree with expert-assigned probabilities. Continuous monitoring of the dam for premonitory signs of instability and a set of loss-prevention plans in the case of a spill provide additional layers of protection; their effectiveness is quantified by estimating the fraction of the population that could be evacuated as a function of warning time. The probabilistic analysis indicates that the safety targets are met and produces practical recommendations on how to maintain and improve the safety level while the dam crest is raised above its current level.CITATION:Van Dyck, J, Pytel, W, Veneziano, D, Snow, R and Zanoli, O, 2015. Safety of a tailings storage facility against dam instability, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 253–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By A G. Noble

Tunnelling for hydro-electric power projects can be a very challenging component of the overall development. In contrast to urban transportation tunnelling where the logistics for access and supply of power, water and other essentials are readily available, hydropower projects are usually in very remote locations and all necessary plant, equipment, spares and materials need to be brought in and the site must function as a self sufficient unit.For a large scheme the river diversion tunnel(s) are usually on the initial phase critical path in order to meet the non-negotiable deadline of river diversion before the onset of the wet season. A newly formed tunnelling crew, once mobilised to the site for the project, will face the first major learning curve of the project’s systems and logistics during this critical tunnelling activity.Power tunnels convey the water to the turbines in the powerhouse and are usually on the critical path for the main works, especially if the scheme comprises a powerhouse located within an underground cavern. A modern cavern arrangement requires a complex warren of various openings: access adits, ventilation/cable tunnels, shafts, surge tunnels, etc.Hydropower tunnel construction tends to be dominated by tunnel boring machine (TBMs) or drill-and-blast excavation techniques and each has its challenges in very remote locations. TBMs still have long lead times as for any type of project, but additionally require a thorough roads and bridges infrastructure assessment of the country from the port of entry to the site to ensure a problem-free delivery. In some cases the project also requires the establishment of a complete precast concrete segment production facility and the space for creation of laydown areas; there is no ‘just-in-time’ delivery mechanism applicable to typical remote hydropower sites.This paper highlights the technical and risk management considerations in the planning, design and construction of tunnels for hydropower projects. It contrasts the typical factors that govern the design of urban transportation tunnels with those for remote hydropower tunnels. The perspectives of stakeholders are provided including those of international lenders. With examples from large and small scale projects across the globe it provides an insight to all parties and in particular, those tunnellers that are working in the hydropower field for the first time.

Mar 8, 2011

By A Giblett, S Hart

"In 2015 operations under the ownership and/or management of all Newmont Mining Corporation subsidiaries (Newmont) produced 5.7 Moz of gold and 619 Mlb of copper from mining operations in five countries, with well over 100 Mt of ore processed by various grinding technologies. Processing methods used in the extraction of metals include flotation, oxidation, conventional cyanidation and heap leaching. The grinding technologies applied in milling operations feeding metal recovery processes include conventional wet grinding semi-autogenous grinding (SAG), rod and ball, dry grinding, concentrate regrinding and ultra-fine grinding, and ball milling of high pressure grinding roll product. SAG/ball (SAB) configurations represent the dominant comminution flow sheet within the company and the circuit configurations employed include SAB, SABC-A, SABC-B and single-stage (SS) SAG milling, with SAG mill feed ranging from run-of-mine (ROM) ore through to secondary crusher product. The collective experiences earned from designing, operating and debottlenecking these various comminution circuits provide many lessons that can be applied to the design and optimisation of future operations. This paper provides an overview of Newmont’s diverse comminution circuits, discusses recent performance and offers some insight into optimisation and design considerations based on recent experience in both endeavours.Citation:Giblett, A and Hart, S, 2016. Grinding Circuit Practices at Newmont, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 293–302 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By D Morrison

Backfill is usually considered a necessary evil that contributes little to the principal objective of the operation, ore production. Consequently, it is relegated to an auxiliary role in the operation with minimal equipment and resource allocation in planning and is only superficially considered during feasibility studies. In many mines, the inadequacy of the design and operation of the backfill system ultimately leads to frequent delays, excessive costs and, in the worst cases, major instabilities which result in reduced ore production and lost or unrecoverable ore reserves. The primary objective of backfill is to prevent the progressive deterioration of mined out excavations. With the exception of narrow vein operations, it is too weak to alter the mining induced stress regime and control stress concentrations caused by stope extractions. However, the direct benefits of backfill include the possibility to consider a wider range of mining methods, recovery of 100 per cent of the planned resource and the selection of a stoping sequence that minimises the regional stability problems that cause production shortfalls in the later years of mine production. Indirectly, backfill is a practical means of solving other issues, such as waste disposal, that impact the viability of mining. In Australia, the geotechnical conditions of many mines are becoming more difficult and increased attention to the importance of backfill is warranted. This paper describes realistic aspects of backfilling and the positive impacts a well co-ordinated fill system can have on mining activities as a whole. Examples are presented where an integrated approach to backfill systems have offered significant benefits to the operation.

Jan 1, 1998

Coal mining legislation makes frequent reference to æSafety Management SystemsÆ but there is a chronic shortage of useful guidance material as to how these might be applied to hazardous exposures. Several studies have indicated that for each death that is reported as a result of an industrial æaccidentÆ, there are five deaths that caused by occupational exposures. Because the deaths from occupational exposures do not occur on site and often well after employment has ceased, they are generally unreported. Improved access to mortality data from coroners, the Australian Institute of Health and Welfare and superannuation service providers (early claims from death and total permanent disability), has given rise to some analysis of death and disability data that provides evidence that there are emerging opportunities to develop and improve safety management systems for hazardous occupational exposures. Issues explored include how safety management systems might be developed in relation to dusts and chemicals and other hazardous exposures to ensure the risk of disorders with long latency periods are reliably assessed and the exposures effectively managed. The current standards and guidelines which refer to safety management systems in general or to management of exposure related hazards are examined. Many standards are based on dose-response studies that provide for an acceptable percentage of workers to suffer adverse health outcomes. An alternative management system might be to apply dose-response relations to health surveillance to identify æat riskÆ individuals and effectively manage health and related safety risk at an early stage.

Jan 1, 2005

In February 1995, Falconbridge Limited approved the construction of a nickel mining and milling facility on its Raglan property situated in the Nunavik region of northern Quebec, Canada. The construction period successfully terminated with the commissioning and start-up of the plant and concentrator in early-December 1997. The estimated life of the project is 20 years with an annual mining rate of 800 000 tonnes of ore, producing 21 000 tonnes of nickel per year. This paper discusses the subject of æRemote Mining in the Canadian ArcticÆ as it applies to the Raglan mine process and people. During the feasibility stage of the project, many assumptions were made which influenced the design and operating parameters of the facilities and the equipment. Transportation, communication, remote logistics techniques and standard industry practices required to support a æfly-in/fly-outÆ operation were reviewed and either adopted or rejected for use at Raglan. These assumptions were æmade to fitÆ the uniqueness of our planned operation. It was also acknowledged that many of them would ultimately impact on the people required to staff the operation following construction. Therefore, their suitability and applicability were examined from an economic, operational and human perspective. In a continuing effort to improve the quality of life for Raglan employees, as well as the economics of our mine operations, these assumptions are under constant review and scrutiny. There is no doubt that experiences gained, and willingly shared by other North American arctic mining operations, proved invaluable and are a big reason for RaglanÆs overall success thus far. The mining industry is being challenged technically to develop lower grade orebodies at the lowest possible cost. In addition to environmental constraints, serious social, political and moral questions are being asked and added to this list of challenges. Miners throughout the world must improve their operating standards and public image if we want to attract the best possible employees. Remote mining operations provide a unique opportunity to experiment with various human resource concepts as well as demonstrate the industryÆs commitment to environmental and community concerns.

Jan 1, 1998

By D J. Brake

The risk from fire remains one of the most serious of underground mine disaster scenarios. The impacts of mine fires on the underground ventilation system and the production of toxic gases have been difficult to model and therefore assessments have relied largely on empirical data, historical precedent and subjective opinions. Underground fire modelling software has had limited availability and been technically challenging and time consuming to use especially for routine mine investigations. There has also been no well-accepted set of assumptions for fire modelling in mines, which has resulted in a lack of confidence in adopting its use more widely. This paper describes modelling of three critical fire scenarios in underground hard rock mines: a fire (LHD) in an underground diesel refuelling facility, a fire in an underground explosives magazine and a fire on an underground ore transport conveyor. Modelling was undertaken using VentsimÆs VentFIREÖ fire simulation module. It describes the basis of design, the key assumptions, the methodology used and provides examples of the outputs, conclusions and recommendations. It reviews the impacts of these fires on egress and entrapment strategies in the mine. Some general principles regarding improvements to ventilation circuit design based on this analysis are also recommended. Whilst the fire scenarios were based on actual case studies, they have been disguised for this paper.CITATION:Brake, D J, 2013. Fire modelling in underground mines using Ventsim Visual VentFIRE software, in Proceedings The Australian Mine Ventilation Conference , pp 265-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

State ownership of minerals results in domestic legislation regulating mining operations. The mining industry today is dominated by a number of transnational companies, each subject to internal and external pressures for a more responsible approach to resource management. Thirty to 40 major companies are responsible for the bulk of the worldÆs mineral production with the balance coming from state-owned, second tier and junior companies and from artisanal miners.Mining companies operating within competitive commercial environments formerly focussed on mineral production. Companies worked to standards and expectations then current which largely failed to recognise the impact of mining activities on community interests. The mining industry acquired a reputation for arrogance, and for placing profitability ahead of issues considered equally or more important by local communities. Current perceptions continue to reflect disquiet about industry attitudes towards traditional land-owners and access to their lands, to environmental contamination, handling and storage of waste materials, utilisation of water and electricity, and to rehabilitation of worked out areas. Major international mining companies concerned at continuing criticism sponsored a series of initiatives with the objective of providing guidance on working harmoniously within the community. Industry commissioned studies, performed through the agency of disinterested parties, resulted in May 2002, in a Declaration being issued at an International Conference in Toronto. The Declaration was based on, but did not reflect all of the recommendations of the MMSD Report, æBreaking New GroundÆ.This paper considers whether benefits would result from the negotiation of a legally binding and enforceable international protocol encompassing the objectives of the MMSD report or the Toronto Declaration. It attempts to identify the problems associated with implementing and enforcing international mining law, should it be introduced. Aspects of mining operations having cover under customary international law are reviewed, as are rights, obligations and remedies for breaches of national mining law. Conclusions are drawn based on established procedures relating to implementing international agreements. The continuing ability of mining companies to operate within communities will result from each satisfying the communityÆs expectations rather than by complying with largely unenforceable legislation.

Jan 1, 2004

By N McKenzie, E Taylor, S V. L Barrett, H Lagger, A Purwodihardjo

This paper discusses the temporary support design methodology for the largest road caverns ever built in Australia—the Lutwyche Caverns—part of the Airport Link project in Brisbane, Australia. The Lutwyche Caverns with a maximum excavated span of 27 m form a key component of this major road project, allowing on and off ramps merging with the underground highway. In addition to the two large span caverns, a 15 m soft ground tunnel with 5 m cover above the caverns and two 24 m deep burial chambers for the 12.4 m tunnel boring machines (TBMs) had to be built in record time at Lutwyche.The temporary support design methodology involved the use of a range of analytical approaches, including empirical methods to provide a starting point for design development, key block models to determine the potential influence of discontinuities on excavation stability and 2/3D continuum and discontinuum models to determine the potential influence of adjacent excavations and the proposed construction staging on the design. In addition, probabilistic analysis of potential kinematic instability using a discrete fracture network (DFN) approach was also undertaken to establish the critical block loads for the temporary lining, while the continuum and discontinuum models were used to design the support for the 1.5 m diameter rock pillar at the north end of the northbound cavern.The numerical modelling was undertaken in close conjunction with the contractor to develop the optimal construction sequence, considering the available construction equipment on-site and the overall project program requirements. Part of the presentation will further show the applicability of the developed design during construction (deformations, monitoring field observations) and lessons learned for future cavern construction in Australia.CITATION:Lagger, H, Purwodihardjo, A, Barrett, S V L, McKenzie, N and Taylor, E, 2014. Temporary support design for the largest road caverns ever built in Australia – the Lutwyche Caverns, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 399–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By N Ganjian, A Delavar, F Rashidi Nejad

Iran is one of the most seismically active countries in the world, being crossed by several major fault lines that cover at least 90 per cent of the country. As a result, earthquakes in Iran occur often and are destructive. So, it is important to consider the seismic stability and reliability of all structures including tailings dams.In this study, the tailings dam stability of the Sangan Iron Ore Mine in Khorasan Razavi, Iran is considered for the case study. The tailings storage facilities of the mine have three cells with the capacity of 45 million cubic metres. The first cell, which has three stages of dam raising, has been recently brought into operation. This cell has a downstream-raised retaining embankment. As the risk of seismicity in this area is high, seismic response of this dam was evaluated by numerical methods. To do this, appropriate models were developed for materials used in foundation and body of the embankment. Then for seismic stability analysis, Tabas (Iran – 1978) and Chi-Chi (Taiwan – 1999) earthquake acceleration simulations were applied.The results of this study indicated that the upstream portion of Stage 3 of the dam and dam crest did not experience significant horizontal displacements during earthquake period, but the downstream portion of Stage 3 of the dam showed a maximum horizontal displacement of 60 cm at the third stage of dam raising. This is three times more than what was estimated by the designer. Also, the maximum vertical displacement resulting from simulation of the Tabas earthquake was 35 cm. The results of dam response to Tabas and Chi-Chi earthquakes indicate that displacement, shear stress and pore pressure by the Tabas earthquake were higher than the case of Chi-Chi earthquake. The higher energy of Tabas earthquake and the higher frequency near to the natural frequency of Tabas earthquake could be the reasons of this difference. The results of this case study confirm that if the studied tailings dam impacted by an earthquake of a similar magnitude to Tabas, the dam will be seismically stable and the developed strains will not be significant.CITATION:Delavar, A, Rashidi Nejad, F and Ganjian, N, 2015. Seismic stability analysis of Sangan Iron Mine Project tailings dam, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By P Holtham, K C. Runge, E Tabosa

Traditionally, comminution and flotation have been surveyed, analysed and optimised separately. This often results in less than optimal outcomes because of the complex interactions between the two processes. Flotation recovery is a strong function of the valuable mineral particle size distribution with lower recovery of ultra-fines due to poor flotation kinetics, optimum recovery for the intermediate sized particles and lower recovery for the coarser particles due to poorer liberation. Thus, to optimise flotation recovery and grade it is usually best to grind to a fine size. This requirement needs to be balanced by the cost of grinding finer and the revenue that results from an increase in grinding throughput, which often results in a coarsening of the flotation feed.This paper demonstrates a technique which can be used to predict the effect of a change in feed grind size on flotation performance. It can be used to determine the optimum grind size for a particular operation which optimises total circuit profitability. Analysis is relatively easy to perform, as a minimum, requiring only size by assay data of the feed and product streams of the process. Case studies will be presented that demonstrate the usefulness of this technique in feed grind applications. Potential use of the technique for regrind evaluation is discussed. The limitations associated with this technique in certain circuit scenarios will also be outlined.CITATION:Runge, K C, Tabosa, E and Holtham, P, 2014. Integrated optimisation of grinding and flotation circuits, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By G A. Blengini, S V. èolar

The minerals industry is faced with choices beginning in the exploration phase and extending over the life cycle of the mine. Firms examine the technical feasibility of alternative actions and typically rank them based on economic performance. Increasingly firms also consider alternativesÆ contribution to sustainable development. There are many visions of what a sustainable future should look like and much debate about what should be sustained. Sustainability is a process, a series of incremental actions, and each alternative course of action has the potential to further progress toward one or more sustainability goal. However, because it is not possible to sustain everything everywhere simultaneously, trade-offs and choices inevitably have to be made.Sustainable decision making before investment (ex ante decisions) should incorporate a broad suite of quantitative and qualitative information. One approach is to utilise an integrated sustainability assessment (ISA) framework that supplements traditional technical and financial tools with other tools such as objectives hierarchies (OH) and life cycle assessments (LCA). OH is a problem framing method that captures stakeholder and decision maker interests, objectives and values. LCA addresses material and energy flows, and environmental impacts. The outputs of these tools can be combined with additional qualitative measures and analysed using multi-criteria decision analysis (MCDA). MCDA models facilitate comparison of different alternatives on the basis of a set of criteria and indicators. Some can incorporate information on risk attitudes and preferences ( multi-attitribute value theory models) and others uncertainty about outcomes (multi-attribute utility models). Studies have been published describing and comparing tools for minerals sector decision analysis. Our paper extends this literature, discussing how a combined OH-LCA-MCDA can support ex ante sustainability assessment by incorporating preferences, risk attitudes, and monetised or non-monetised social and economic variables, in a manner that captures their inherent complexity. We also discuss how such a combined model would support trade-off analysis.

Jan 1, 2009

By J Carter, B J. Armstrong

Best practice for the submission of samples to an internal or commercial laboratory requires quality control materials to be included for the purpose of independently and comprehensively assessing laboratory performance. These quality controls include the use of certified reference materials (CRMs) and may be blind to the laboratory. Iron ore companies purchase these materials from reputable manufacturers from stock of run-of-mine materials at the appropriate grades. The international standard, ISO 17034 (ISO, 2016), specifies the competency requirements for organisations manufacturing reference materials, and includes rigorous requirements for the assessment of homogeneity, stability and establishment of property values and their uncertainties. Homogeneity is one of the most important measures of suitability for all certified reference materials and refers to the degree to which the composition and properties of a sample are uniform throughout the batch, relative to the analytical precision of the method. More specifically, homogeneity studies of candidate reference materials should be assessed for both within sample variance and between sample variance with appropriate statistical controls. The design and application of homogeneity studies are discussed as they apply to both crushed and pulverised reference materials. Crushed certified reference materials have been utilised by the iron ore industry for a number of years and provide the user with a critical assessment of variances in sample preparation in addition to analysis. Crushed reference materials are similar in presentation to an RC sample and are generally used as discrete parcels of material submitted to the laboratory from the field. Pulverise certified reference materials miss the sample preparation step and are subsampled from th delivered sachet at the point of analysis. This paper compares the relative homogeneity performance of crushed and pulverised certified reference materials by grade across key iron ore chemical constituents. Outcomes are benchmarked to the international standard ISO 9516 (ISO, 2003) for the determination of various elements in iron ores by lithium borate fusion and X-ray fluorescence. Practical implications are discussed with reference to a case study from an iron ore laboratory in the Pilbara.

Sep 18, 2023

By L Blackwell

Strategic mine scheduling is an industry best practice for increasing the long-term value of mining operations and supply chains. The application of optimisation technology such as mixed integer linear programming (MILP) is able to achieve a mathematically optimal result for a given scheduling model. Such a model will typically define the available source material, processing options and desired constraints for accessing and processing the material. Most strategic scheduling models, however, do not include a sufficiently detailed model of capital expenditure options related to capacity expansion.Typical strategic schedule models do not include important capital expenditure features such as capacity decay or expiration (limited lifespan of trucks), precedence relationships over time (rail construction before a new plant or non-linear expansions due to economies of scale) or mutually exclusive option sets (choices of plant size). By not including these features, a strategic mine scheduling model for a capital-sensitive operation is unable to be optimised to deliver maximum value or profitability.This paper presents several results of MILP optimisation using advanced capital expenditure modelling for mining operations and supply chains. Results of the study demonstrate that optimising capital expenditure at the same time as optimising the mining schedule allows for minimisation of capital purchasing, optimal timing for those purchases and optimal scheduling around them. Overall, this results in an increase in net present value.CITATION:Blackwell, L, 2014. Capital expenditure modelling for strategic mine scheduling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By A Dennis, T Hunter, R Coleman

For metallurgical plant design, it is necessary to progress through successive phases of test work, piloting and process development before involving all the other engineering disciplines and “freezing” the process design criteria and flow sheet. This process usually relies upon the experience, skills and personal preferences of various technology providers, study and engineering entities, test work and metallurgical laboratories and, most importantly, the owner’s team and its operators. Current industry trends include lower grades, more complex orebodies, geometallurgy in defining orebody variation and design envelopes, more common “hybrid” plant processes and the market demands for more reliable, timely and predictable early plant performance.This paper will discuss interaction of these trends and provide guidelines for the level of detail and technical complexity required for a number of different “typical” examples. The paper will pay particular attention to the study definition level translated into the required detail and certainty needed by the overall process “owner” and original equipment manufacturer (OEM) equipment suppliers to ensure the best real plant performance. Some recent case studies will be discussed. In many projects, at a late stage of project definition, it has become common practice to undertake a “value engineering” phase. Although it could be argued that this should be undertaken earlier, it is largely driven by an overall need to reduce capex and “optimise” the perceived “fat” built into the project during the detailed design process. This value engineering can be very counterproductive to project timing and operational performance and warrants discussion.The paper is intended to promote discussion on a topic of wide interest. The authors’ diverse backgrounds and experiences are integral to the views in this paper.CITATION:Dennis, A, Coleman, R and Hunter, T, 2017. Critical process design considerations from test work to operations, in Proceedings MetPlant 2017, pp 12–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By M Scoble, C Hughes, M Roberts

At 14 per cent, the representation of women working in the mining industry is the lowest among primary industry categories in Canada. Despite an increase in research and industry commitment to advance and retain women in the mining industry, the gender gap in mining organisations persists.This paper is based upon a recent Canadian survey of 163 highly qualified women (HQW) working in the mining sector. For the purpose of this research, HQW were defined as women with a BachelorÆs degree or higher. This research sought to identify career progression and retention patterns of women who in theory have the educational qualifications to advance into positions of leadership in mining operations. We considered why womenÆs advancement in mining organisations has stalled; examined the career development pathways of HQW; and investigated the interactions of mining workplace culture on HQWÆs career development and retention within the Canadian mining industry. Results?indicated two distinct career pathway trends for HQW. æThe specialistÆ; a career characterised by multiple professional scientific and technical positions, and æthe corporateÆ; a career characterised by professional administrative roles and roles in mid-level management. It was found that neither æcorporatesÆ nor æspecialistsÆ systematically progressed into senior management and executive roles. These findings suggest that HQWÆs careers in mining are stalled, despite a strong indication by respondents of interest in their professional career advancement. With regards to?workplace?culture, respondents indicated that blatant forms of gender discrim-ination have been reduced in mining workplaces; however, exclusion from informal networks, implicit bias and subtler forms of workplace discrimination persist. Consistent with previous mining sector research, improving work-life balance, work flexibility and mentorship were found as key drivers for HQW to advance and remain in the industry.CITATION:Hughes, C, Scoble, M and Roberts, M, 2012. Where are the women? Highly qualified women in the mining industry, in Proceedings International Mine Management 2012, pp 23-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By M Colwell

The Coal Mine Roof Rating (CMRR) is a rock (roof) mass classification (RMC) system/index that was originally developed by the United States Bureau of Mines (USBM) for aspects of underground coalmine geotechnical design and was first introduced to Australia as a part of the original Analysis of Longwall Tailgate Serviceability (ALTS) project conducted in 1997/1998. In subsequent years further refinement to its calculation was undertaken, such that the CMRR is now an industry standard for quantifying the structural competence of the primary bolted roadway roof interval and has been routinely/widely used by Australian collieries over the last 25 years with great success for roof support/chain pillar design. There have been many publications discussing the use and calculation of RMC systems and this paper also provides an important update and recommendations in how best to calculate the CMRR. However, it is rare to find an explanation as to why and how a RMC system/index satisfactorily takes account of the mechanics and rock mass behavioural issues associated with ground reinforcement. This paper provides such an explanation and insight with respect to the CMRR so it is: 1) better understood, 2) to allay any concerns, and therefore 3) will continue to be confidently used by and for the collieries’ benefit.

Nov 29, 2022

By D Liu, M Edraki, L Berry

The presence of clay minerals slows down the settling rate and mitigates compact consolidation efficiency in tailings dewatering. The increasing use of saline water in many plants, affects the dewatering performance and presents the mining industry with new concerns. Efficient tailings dewatering is a great challenge due to the complexity character of tailings, especially clay mineralogy, clay content, and water chemistry. In this study, existing studies of the effect of different affecting parameters, such as pH, ionic strength and polymer flocculants, on clay aggregation behaviours are reviewed. The settling behaviours of three types of commonly observed clay minerals in tailings, kaolinite, bentonite, and illite, are also investigated in saline water with different water salinity as a case study. The settling rates of clay minerals are found to be affected by water salinity, clay type, clay content and polymer dosage levels. High salinity water hinders the settling of kaolinite but assists the settling of bentonite and illite through formation of different aggregation structures.The current work has indicated that strategies to promote more rapid dewatering could include adjusting flocculant type or level, water salinity and salt balance, and tailings solid content levels. Implementing dewatering strategies may require a more detailed knowledge of the effect of surface chemistry on the nature and strength of the clay inter-particle forces. This study discusses the research gaps on how to better manage clay-rich tailings in saline water and identifies new research directions. The development of a water management model, supported through in-line monitoring data to predict and manipulate of the surface chemistry of the clay component of the tailings could be a new direction to manage the issues associated with clay minerals in the process of dewatering and tailings management. Mine planning (water use requirements, operating costs) could benefit from more detailed studies on dewatering of clay-rich tailings in saline water. CITATION:Liu, D, Edraki, M and Berry, L, 2018. Improving the dewatering efficiency of clay-rich tailings in saline water, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 476–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018