Search Documents

By H. F. Moore

Jan 1, 1936

By H. H. Evinger, M. Muskat

Although the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.' In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was measured and an attempt was made to determine the effectiveness if sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to deter-mine the effect of tamping were performed by Snelling and IIalL2 Small charges (zo grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.~ The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.6 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

By J. F. Fidiam, T. F. Ford, A. G. Loomis

It is only within the past 10 years that serious attempt appears to have been made to improve rotary drilling fluids by the application of the principles of colloid chemistry, although the use of chemicals to control the rheological properties of clay slips has long been known in the ceramic industry. The main difficulty apparently lay in the lack of a complete analysis of all of the functions of a drilling fluid in the drilling of the well, together with the lack of adequate consideration of how colloid science could be applied to secure these ends, and particularly how apparent antithetical properties of the fluid could be compromised. Thus one analvsisl of the many requirements of a drilling fluid proved conclusively that the viscosity should be low, in order that cuttings and entrained gas might be eliminated effi-ciently in the settling ditch, while the loss in carrying capacity accompanying low viscosity could be regained by increasing either the density of the mud or the upward velocity of the mud stream in the annular space of the well, and the danger of sticking of the drill stem due to rapid settling in case of enforced suspension of drilling operations could be eliminated by enhancing the thixotropic properties of the fluid. The desired properties of the drilling fluid having thus been established, it was a natural step to treat the fluid with vis-cosity-reducing chemicals, such as salts of weak organic acidsl for example, sodium tannate or gallate—and to adjust the pH to the alkaline side to such a degree of thixo-tropy as would give low viscosity and low yield point under the conditions of flow prevailing in the settling ditch, but rapid gelation and high yield point when quiescent in the annular space during shutdowns. In fact, flow in the settling ditch should be just short of turbulent while flow in the well, together with the flow of mud past the cuttings, is practically always turbulent. The use of chemicals other than those mentioned, such as Calgon (sodium hexametaphosphate) and certain other phosphates together with sodium tannate, has now become standard practice and it is the consensus that this method of treatment has proved to be an important step in the development of the art of drilling oil wells. It is safe to assume that the application of colloid chemical principles can also help in solving other outstanding problems of drilling fluids, such as the development of cheaper and more efficient viscosity reducers ; the development of chemicals that do not lose their effectiveness in a short time during drilling operations; the finding of chemicals to preserve the plastering properties of muds when concentrated brines are encountered or in drilling through salt beds; improvement in the plastering properties of poor muds by further defloc-culation, and, conversely, the prevention of excessive deflocculation of certain marine shales sometimes encountered; the preparation of muds suitable for the successful drilling of heaving shale formations; the finding 0f chemicals to treat the mud to prevent or to diminish lost circulation; the development 0f muds that will not impair 6

Jan 1, 1941

By S. N. Kesten, Richard Murphy, A. H. Land, W. F. James

Introduction—by W. F. James and A. H. Lang This paper describes the geology and present state of development of uranium and thorium deposits in Canada. It is expected that this information will be added to that now being assembled from available American and British data to provide a background for engineers and others who may be called upon in the future to examine or search for radioactive deposits. Some generaliza- tions regarding the Canadian deposits are included, but many of these are necessarily tentative. The information contained in the paper is up to date for the end of 1948. The information contained in this paper has been derived from many sources. Much of it is from the records of the Canadian government-owned Eldorado Mining and Refining (1944) Limited and from examinations of government and private properties made by officers of the Geological Survey of Canada. Some information on privately-owned properties has been quoted from other sources mentioned in the text. The information has been assembled by W. F. James of Eldorado Mining and Refining (1944) Limited and A. H. Lang of the Geological Survey of Canada, who have written the sections for which they are credited. The description of the Eldorado mine is based on reports by Richard Murphy, formerly chief geologist for Eldorado; the report by Mr. Murphy was published previously by the Canadian Institute of Mining and Metallurgy,' to whom the writers are indebted for permission to repub-lish. The section dealing with the geology of and development work in the Goldfields area, where Eldorado has important holdings, is by S. N. Kesten, field geologist for Eldorado. The geological diagram of the Goldfields area (fig. 2) was kindly supplied by A. M. Christie of the Geological Survey of Can-

Jan 1, 1951

By H. l. Burghoff, E. C. Bohlen

The work reported in this paper was carried out to supplement the existing information concerning directional properties and recrystallization textures of annealed brass sheet and strip. These characteristics are of direct interest when the forming and drawing properties of such material are being considered. Among those who have made contributions in this field are Bass and G1ocker;l Bauer, Göler and Sachs;2 Phillips and Samans;3 Pratt;4 Price;5 Cook;6 Richards;7 Brick;8 and Brick and Williamson.9 These investigators have found, in general, that in brass strip that shows directional variations in properties, tensile strength has a minimum value and elongation has a maximum value at 45' to the rolling direction. The most pronounced directional properties have been found in material given the greatest reductions in rolling followed by high annealing temperatures. Recrystallization texture of brass has been variously reported as (II3)[II2], (ooi)[ioo], and a combination of (II0)[II5] and traces of the primary rolling texture, (110)[112]. The directional studies have been very informative, but actual tests appear to have been confined to material in its final condition. Tests at intermediate stages have received little attention although previous history of some materials has been partly considered. Perhaps the most comprehensive investigation was made by Cook,' who studied the directional properties of 70-30 brass strip for which the final and penultimate, or next to the last, anneals and the final reductions were varied. He found that, for any given combination of penultimate anneal and final reduction, the tendency toward the development of directional properties was reduced as the temperature of the final anneal was decreased. In addition to drawing cups and making tensile tests of the finished material at various angles to the rolling direction, he measured the frequency and the angles of twins in grains for several specimens. Plots of his twin counts showed directionality for the materials that produced eared cups. Test Materials and Equipment For this investigation, one commercial heat of 68-32 brass was cast in the form of bars for cold-rolling, I31/2 in wide and I1/2 in. thick. The analysis was as follows: 68.83 per cent copper, 0.04 per cent lead, 0.01 per cent iron, 31.12 per cent zinc (by difference). The bars were so processed to the final thickness, 0.020 in., as to obtain on this thickness all possible combinations of the variables listed below except those involving the sequence of 84 per cent penultimate reduction and 84 per cent final reduction: I. Penultimate reductions of 37 per cent, 50 per cent and 84 per cent; 2. Penultimate anneals at 800°, 900°, 1050° and 1200°F.; 3. Final reductions of 37 per cent, 50 per cent, 69 per cent and 84 per cent;

Jan 1, 1942

By R. H. Brown, F. Keller

Because of the extensive use of Alclad 24s alloy sheet in aircraft construction, there is much interest in the metallurgical changes caused by heat-treatment of this product.1, 2 One of these changes is the result of the diffusion of soluble elements from the core into the coating during treatment. This paper deals with the thermal treatments that may influence diffusion and with the practical effects of diffusion on the serviceability of the product. As is well known, Alclad 24s-T sheet has a core of high-strength alloy combined with surface layers of relatively pure aluminum. The microstructure of a cross section of this product is shown by Fig. I. Not only does the relatively high-purity coating have a high resistance to corrosion, and hence serves as a mechanical barrier between the core metal and the corroding environment, but in addition this coating exerts electrochemical protection over areas where the core may be exposed, such as cut edges. In addition, the coating affords electrochemical protection to projecting heads of A17s-T, 17s-T and 24s-T rivets, or attached members made from these alloys. Under some conditions of heat-treatment, however, diffusion of copper into the coating will alter the electrochemical relationship between the coating and the core to the extent that only partial protection will be obtained under some corrosive conditions. The reason for the electrochemical protection lies in the fact that the coating layers of pure aluminum are anodic to the alloy core. The addition of copper to aluminum produces alloys in which the potential is lower than that of the pure metal. Moreover, as the amount of copper in solid solution in 24s alloy is increased, the potential of the alloy becomes more cathodic. When heat-treated at 920°F. and quenched in cold water, 24s-T is about 0.16 volt cathodic to pure aluminum. However, copper will diffuse from the core into the coating, and if it reaches the surface the potential will be altered in a cathodic direction. Thus the potential difference between the core and coating may be less than 0.16 volt, depending uponIthe thickness of the coating, and the time and temperature of heat-treatment. Of the methods available for determining the extent of diffusion of copper from the core into the coating of Alclad 24s-T, two are generally used; namely, the metallo-graphic and the solution potential methods.3 Metallographic Methods Metallographic methods will reveal the progress of diffusion of copper into the coating. For instance, the diffusion zone in the coating intermediate between the coating surface and the core is shown in Fig. I. This photomicrograph is of a polished and etched cross section of 0.040-in. Alclad 24s-T sheet. Diffusion proceeds into the coating more rapidly along the grain boundaries than through the body of the grains. Consequently, the diffusion zone is not of uniform width

Jan 1, 1944

By R. Floyd Farris

A method is presented for determining minimum waiting-on-cement time, which takes into account the differences that exist between types and brands of cements and such individual well conditions as depth, temperature, and pressure. The basis for the method was determined by laboratory tests. Being a laboratory development, several steps were required to prove its merit. The first step consisted of laboratory tests designed to determine the minimum cement strength required in wells. Basis was found for setting a minimum value of 8 Ib. per sq. in. tensile strength. Next, it was shown by laboratory tests that the time to 8 Ib. per sq. in. tensile strength may be expressed as a function of consistometer stirring time to loo "poises," the approximate relation being "the time to 8 Ib. per sq. in. tensile strength equals the time to I00 'poises' times three." Next, it was shown that the time of maximum temperature development in cement slurries, due to heat of hydration, is also related to consistometer stirring time to loo poises, but only by a factor of approximately two. It was shown also that the shut-in casing pressure will build up after cement is placed and register a maximum pressure at approximately the same time the slurry down the hole attains maximum temperature. From this and the relationships listed above, the general rule was established that minimum waiting-on-cement time (time to 8 Ib. per sq. in.) after casing cement jobs in any well is equal to the time when the shut-in casing pressure reaches a maximum, as measured from the initial mixing of cement, times a factor of 1.5. Cement plugs drilled in the field at the time prescribed by this formula were found to drill "firm to hard," thus confirming the laboratory tests. These tests prove that many of the present regulations for waiting on cement require a longer time than is absolutely necessary. Use of the method herein proposed offers the possibility of a saving of $1200 per well. Introduction The length of time allowed for cement to set after casing is determined either by state-wide rules, field rules, or self-imposed rules written into drilling contracts. In general, the time is dictated by experience and common practice. However, owing to differences in opinion and in experience of the various groups involved, waiting-on-cement time often varies from one area to the next. For example, an operator in an area where no rules exist may drill out of surface pipe at 24 to 36 hr., while another operator in another area may wait 48 hr. or more to comply with state or field rules, although the depth of the well, hole size, type of cement, and other data are identical. An even greater difference in practices will be found by making similar comparisons with respect to oil-string cement jobs. Differences in waiting-on-cement times of 36 to 48 hr. are common. Further complicating the picture is the rather common practice of allowing more waiting time for cement to set at the greater depths than is allowed at the shallow depths. This practice has existed for years in spite of the common knowl-edge1,2,3 that the temperature of the earth at the usual setting depths of surface

Jan 1, 1946

By M. Cohen, R. T. Howard

It has long been realized among metallurgists that a fast, reliable method for the quantitative determination of the percentage of microconstituents in an alloy would be of great benefit in studies of equilibrium and transformation in the solid state. For example, Polushkinl has shown that the compositions of two coexisting phases in a binary system at a given temperature may be calculated very simply with the aid of two alloys lying in the two-phase field if the relative amounts of the two phases in each alloy can be determined. Recently, Grange and Stewart2 have traced the course of the austenite-martensite reaction in a series of commercial steels by making visual estimates of the percentage of martensite formed as a function of cooling temperature. The correlation of mechanical properties with structure, a subject of wide-spread current interest, is likewise dependent upon quantitative microanaly-sis. Yet, there are very few investigations described in the metallurgical literature, wherein methods of quantitative microscopy are employed. Usually, the relative amounts of the microconstituents are estimated in a qualitative or semiquantita-tive way. The authors were faced with this problem some time ago in studying the kinetics of austenite decomposition. Several aspects of this research could not be treated satisfactorily by other quantitative tools, such as specific volume,' magnetic,6 dila-tometric, electrical resistance7 or x-ray measurements.a It became necessary to find an impersonal quantitative method that could be applied to microstructures. Fortunately, it was noted that geologists and petrographers had coped with quantitative microscopy to a considerable degree in their attempts to evaluate the mineral contents of rocks. A number of excellent articles were found on this subject, and since they appear to be unknown generally to many metallurgists, the first part of the present paper is concerned with a review of the literature in some detail. With this survey as a background, the authors have adapted the so-called methods of point-counting and lineal analysis to metallography, as described in the second part of the paper. Austenite-martensite structures were selected for illustration not only because they are important in many ways, but because such fine intermixtures are notoriously difficult to estimate visually. Literature Survey Perhaps the earliest work on quantitative microscopic analysis goes back to Delesse9 (1848) who proved mathemati-

Jan 1, 1948

By M. Prats, D. G. Russell

The performance of a well in a bounded, layered reservoir with interlayer crossflow has been investigated mathematically. The system studied comprises a centrally located well in a bounded cylindrical reservoir composed of two layers of contrasting physical properties. The reservoir contains a single fluid of small and constant compressibility. In the case of a well producing at constant pressure, the production rate of the crossflow system declines exponentially after the early transient behavior dies out. For wells which produce with constant rate, the pressure-time relationship is linear following the transient. For very early production time, the production rate of the two-layer crossflow system behaves as that of the two-layer stratified system (the case in which the layers are in communication at the well only). Except for early time, in most practical cases the performance of a two-layer reservoir with cross-flow can be duplicated by that of a single-layer reservoir. The equivalent single-layer reservoir must have the same pore volume and the same drainage and wellbore radii as in the two-layer case. In addition, the equivalent reservoir must have a "kh" (permeability x thickness) product equal to the sum of the "kh" products of the respective layers in the crossflow system. If the porosity and permeability distributions are known, the production and pressure behavior of a well with and without crossflow can be predicted. From a comparison of the observed pressure or production performance of a well and the theoretical behavior, the occurrence of interlayer crossflow can be detected. INTRODUCTION When flow is possible across the bedding plane from a low-permeability layer into an adjacent layer of moderate or high permeability, the earlier depletion of the more permeable layer will cause such flow to occur. If this situation exists, the oil recovery from tight layers can be appreciable; thus, the economic ramifications of interlayer crossflow are apparent. The possible importance and extent of flow between adjacent and connected layers — whether resulting from capillary, gravitational, or viscous forces — have been the subject of considerable speculation for many years. Jacquard1 presented a rigorous analysis of the crossflow due to single-fluid expansion occurring between two adjacent and connected layers when the well produces at constant rate. His presentation was entirely mathematical, however, and no numerical results from evaluation of the mathematical solutions were presented. Our objectives in the preparation and presentation of the present paper are essentially twofold— (1) to analyze the behavior of a well which produces a single compressible fluid from a bounded, layered reservoir with interlayer crossflow, and (2) to present practical numerical results and simplified formulas to facilitate engineering analysis of reservoirs with crossflow. The constant-terminal-pressure case was analyzed rigorously, whereas the constant-terminal-rate case was treated only for semisteady-state conditions. DESCRIPTION OF THE IDEALIZED TWO-LAYER RESERVOIR The reservoir to be studied is assumed to be bounded and cylindrical in shape, with a completely penetrating well at its center. The reservoir is composed of two adjacent horizontal layers between which fluid is free to flow. Each layer is assumed to be homogeneous, isotropic and completely filled with a fluid of small and constant compressibility. The total thickness of the reservoir is small enough

ALABAMA. Anniston.-Noble, A. E., 20th St. and Wilmer Ave. Auburn.-Brown, R. L., Box 0. Belle Ellen.-Hutcheson, W. C. Bessemer.-Abbott, C. E., T. C., I. & R.R. Co Dobbs, G. G., Box 97. Ferguson, V., U. S. C. I. Pipe & Fdy. Co. Williams, E. P., Tenn. C., 1. & R. R. Co. Birmingham.-Aldrich, T. H. Aldrich, T. H., Jr., 406 Woodward Bldg. Allen, A. W., 1616 S. 14th Ave. Bowron, J., 1401 S, 20th St. Burbidge, T. A., Brown-Marx Bldg. Coxe, E. H. Tenn. C., I. & R. R. Co. Crawford, C. G., Tenn. C., I. & R. R. Co. Crockard, F. H., Brown-Marx Bldg. Ellis, E. E.,1515 Brown-Marx Bldg. Fairbairn C. T., Woodward Bldg. Fies, M. H., 2316 Highland Ave. Geismer, H. S., Keiser-Geismer Engrg. Co.

Jan 1, 1917

By A. U. Seybolt

The pressure-temperature relations required to maintain the existence of Si3N4 in silicon-iron of 0.44-11.7 pet Si have been partially explored. The critical data obtained have allowed the calculation of some thermodynamic quantities, and have shown evidence of an order-disorder two-phase field extending at 800°C from about l pet to 5.5 pet Si. THE presence of silicon nitride in electrical sheet, nominally about 3 1/4 pet silicon, balance iron, has been described by several authors'" but there has been some discrepancy among them regarding the identity of the nitride. Also, little has been reported on the quantitative thermodynamic prop- erties. In the work to be reported here, the nitride has been found to be more stable than described by Corney and Turkdogan." Several silicon nitrides have been described in the past, including SiN, Si3N4 and Si2N4 (see, for example, Abegg6 and Pascal7). However, the literature on nitrides other than Si,N, is all very old. No recent investigators using the more powerful tools available today have reported the presence of any nitride other than S3,N4. W. B. Hicke and L. R. Brantley8 in 1930 determined the dissociation pressure of Si3N4 which they made by reacting nitrogen

Jan 1, 1959

By M. Semchyshen, G. A. Timmons

The predominant orientation in both straight-rolled and cross-rolled molybdenum is the {100} [110] texture. Upon complete recrystallization, this same texture predominates, but there is less spread about the ideal orientation. A secondary orientation about the [111] direction as the axis develops in cross-rolled sheet. Compression-rolled sheet exhibits random orientation in the plane of the sheet. Some mechanical properties were measured at varying angles to the rolling direction to determine the effect of preferred orientation on anisotropy in molybdenum sheet which had been straight, cross, or compression rolled. THE development of the arc-cast process has made available large ingots of molybdenum from which it is possible to roll sheet of considerable size. It is anticipated that such sheet will be further fabricated by spinning, drawing, stamping, or forming. Anisotropy of physical properties caused by the preferred orientation developed in the sheet during rolling may be expected to affect the behavior of the metal when subjected to these fabricating operations. To produce a sheet which will be most amenable to the fabrication of a given shape by a particular operation, consideration should be given to the directions and magnitudes of plastic deformations produced in the operation. When possible, the rolling schedule should be controlled to develop a texture which favors the required deformation. The existence of preferred orientations in rolled molybdenum sheet has been reported by Jeffries,' Konobejewsky,' Fujiwara," Goss,' and Ransley and Rooksby." None of these investigators obtained sufficient X-ray data to permit the construction of pole figures; instead, they based their conclusions upon Debye-Scherrer patterns of a limited number of positions. Ransley and Rooksby devoted some attention to transcrystalline cleavage at 45" to the rolling direction, indicating that it is appreciable in polycrystalline material only when the crystals are in the ideally preferred condition, and that this condition is only approached if the metal has been rolled successively in two perpendicular directions. In a recent paper, Custers and Riemersmao introduced the first pole figures to describe the textures of straight-rolled and cross-rolled molybdenum sheet. To increase the knowledge concerning the generation and effects of preferred orientations in molybdenum sheet, an investigation was undertaken to determine the effects of variations in rolling schedule and annealing treatments on preferred orientation, and to correlate preferred orientations with some mechanical properties. The orientations of straight-rolled, cross-rolled, and compression-rolled sheet have been determined by X-ray analysis, both as-rolled and after recrystallization. Pole figures have been constructed to describe the textures produced by these various rolling procedures. Texture of Cast Molybdenum Ingots In the arc-cast process, molybdenum powder is pressed into a vertical column which is sintered to increase its strength as it proceeds downward into a water-cooled mold, where the metal is melted in an alternating-current arc established between the end of the formed powder electrode and the metal bath at the top of the growing ingot. Since the solid-liquid interface moves continuously upward in the mold, the crystal axes are not normal to the cold surface of the mold but have the curvature shown in Fig. la. X-ray analysis reveals that the cube axis is the fiber axis and that it is normal to the cold surface of the mold; that is, the [loo] direction is parallel to the longitudinal axis of the ingot. This substantiates recent work by

Jan 1, 1953

By Fred L. Morritz, Harold M. Manasevit, Richard Nolder, Arnold Miller

Experimental evidence is presented which confirnis the epitaxial relationship between the deposited silicon and the sapphire substrate. Four distinct modes of orientation relationships have been established. These have been shown to be Single-crystal gvowth retention as a function of surfaces oriented off ideal has been qualitatively indicated. Both full-circle goniometer X-ray techniques and replica electron microscopy have indicated varying amounts of microtwinning in the silicon. film, which may he caused by the mode of silicon formation. Parameters have been found where twin density is less than I pct. The early stages of' epitaxy of silicon m sapphire have been examined by electron-microscope techniques... and mechanisms have been proposed. THE first report of the deposition of single-crystal silicon on sapphire (single-crystal aluminum oxide) was made at the American Physical Society Meeting in Canada' by one of us and was subsequently published in the Journal of Applied physics.* This paper summarizes some of the work carried on in this area since that time, in addition to reviewing some of our earlier observations. The initial single-crystal deposits of silicon on sapphire reported were obtained on sapphire planes produced by cutting a sapphire rod perpendicular to its fastest growth direction, which is approximately 60 deg from the C axis. Direct correlations between the microstructure and X-ray data as to the single crystallinity as shown in Fig. 1 are evident. These deposits were identified as (111) silicon on the substrate oriented near the (1123) of sapphire. (Sapphire notations are designated according to the c over a ratio of 2.73.) It became evident that substrate quality and surface play an important part in successful epitaxy. For example, in Fig. 2 we observe an interesting

Jan 1, 1965

By C. J. Rosa, W. C. Hagel

An attempt is made to determine the diffusion coefficients of oxygen ions in hypostoichiometric zirconium oxide. A phenomenological theory is developed for three-phase, unidirectional volume diffusion of a gaseous species from a planar source. Knowledge about oxygen diffusion in a and ß zirconium and experimentally measured rates of movements of interfaces permit the evaluation of oxygen ion diffusivi-ties in ZrO2-x. The results conform to the relationship: sq cm per sec, for the temperature range of 875" to 1050° C. DIFFUSION coefficients of oxygen ions in stoichio-metric oxides have been studied by many investigators. The obtained results not only supplement the knowledge about the lattice-defect structures of oxides and conduction mechanisms but also provide information of technological importance. Rate processes such as oxide sintering, high-temperature creep deformation, and oxidation of metals and their alloys are directly dependent on diffusion phenomena. Unfortunately, diffusion coefficients obtained from studies on stoichio-metric oxides cannot be treated without restraints when applied to oxidation kinetics, if precise evaluations of oxidation rates are desired. Oxides formed on metals are usually nonstoichiometric and exhibit nonuniform distribution of either cation or anion vacancies across their thicknesses. Debuigne and Lehr1 extended Danckwerts'2 mathematical analyses and furnished a semitheoretical treatment for evaluating oxygen diffusion coefficients in zirconium oxide in terms of weight gain measurements during oxidation of zirconium in the temperature range 400° to 850°C. Their calculations are based on theoretical partitioning3 of the total amount of oxygen between a zirconium and its oxide phase. An inherent discrepancy appears to continue throughout their calculations. The amount of oxygen confined to the oxide phase should be corrected by multiplying the calculated oxide thickness by the inverse of Pilling-Bedworth ratio, if expansion of zirconium dioxide is taken into account. The purpose of the present investigation is to provide a new semitheoretical treatment for evaluating diffusion coefficients of moving species in hypostoichiometric oxide. The analyses are relevant to unidirectional volume diffusion. Although the presented method is quite general, its applicability will be discussed in terms of kinetic measurements from oxidation of zirconium at temperatures above the a/ß transition, for reasons stated in the later part of this paper. EXPERIMENTAL Pure, 99.93 wt pct, zirconium samples of approximately 2 by 1 by 0.35 cm were exposed to oxygen for various times at four temperature levels: 875°, 950°, 1000°, and 1050°C. High-purity, better than 99.9 vol pct oxygen was passed through a cold trap and columns containing anhydrous CaSO4 to remove residual water vapor. Before exposing to oxygen at a pressure of 500 Torr, specimens were subjected to wet abrasion on 200- through 600-grit Sic papers and polished with 1—p diamond dust. Prior to oxidizing, all zirconium samples were vacuum-annealed at 10-6 mm Hg for about 15 min at the test temperature. The temperature variation across the uniform heat zone was ±2°C from the preset value. Final polishing, for phase thicknesses measurements, was performed by using 8- and 1-p diamond dust and followed by vibrator polishing with 0.05-µ ? Al2O3 solution. Measurements of phase thicknesses were made by projection on a metallographic viewing screen. Conventional powder X-ray analyses for the oxide were employed. RESULTS Fig. 1 is an example of the cross section of oxidized zirconium. Designations of phases given below this figure are the same as those used in the three-phase diffusion system represented by Fig. 5 in the following section. Zirconium oxidized for longer exposure times showed two types of oxides: white oxide at the surface and an underlaying layer of gray oxide. X-ray powder patterns of these oxides at room tern-

Jan 1, 1969

By Henry P. Ehrlinger, James C. Bradbury

Tripoli is a naturally occurring, very finely divided form of silica found chiefly in some midwestern and southeastern states and used commercially as fillers and abrasives. Definitions Tripoli is a microcrystalline, finely particulate, more or less friable form of silica that appears to be the product of leaching of siliceous limestone or calcareous chert. The term was originally applied to a deposit near Seneca, MO, that resembled material of that name found near Tripoli In North Africa (Hovey, 1894). The two deposits were subsequently found to have different physical characteristics -the North African tripoli, now called tripolite, is a diatomite, composed of the siliceous skeletons of microscopic marine plants called diatoms; the Missouri tripoli contains no diatom remains. The term tripoli, however, continued to be used for the Missouri material and is now applied in a general way to most silica deposits similar to it in characteristics and geologic origin. In commercial trade tripoli is commonly understood to designate material from the Missouri-Oklahoma field; silica from southern Illinois, the other major producing area, is referred to commercially as amorphous silica. Each term, however, may be used commercially for material, regardless of place of origin, that has the characteristics or uses commonly ascribed to the material from one or the other major producing area. For example, in the commodity price listings, Engineering & Mining Journal routinely lists under Tripoli, prices "f.o.b. Elco, IL" and "f.o.b. Seneca, MO, and Rogers, AR," and under Silica, amorphous, prices "f.o.b. IL," and "f.o.b. bierks, AR." Amorphous silica, the commercial designation given to southern Illinois tripoli, is, like the term tripoli, a misnomer. Mineralogically, the southern Illinois deposits are composed of microcrystalline quartz, and no amorphous material has been detected during X-ray and scanning electron microscope investigations (Leamnson, Thomas, and Ehrlinger, 1969; Thomas et al., 1970; Keller, 1978). Soft silica is another term that has been applied to Illinois and Tennessee tripoli, presumably to distinguish it from the more compact Missouri material. It has also been used in the ceramic trade to distinguish tripoli from "hard" silica, or silica flour, produced by pulverizing silica sand (Heinz, 1937). Rottenstone, produced commercially in Pennsylvania, is similar to tripoli in that a major constituent is finely particulate silica, and its uses are much the same as those of Tripoli-as abrasives and fillers. The origin of rottenstone also is similar to that of tripoli-decomposition of a siliceous sedimentary rock. The parent rock is defined as a siliceous limestone (Gary, McAfee,, and Wolf, 1972; Thrush, 1968) or as shale. Heinz (1937) quotes a brief statement describing the Pennsylvania deposits -"a black impure shaly limestone grading into black shale"-but does not identify the source of the statement. For convenience, rottenstone is included with tripoli in the reporting of production statistics in US Bureau of Mines (USBM) Minerals Yearbooks. Other materials that have been called tripoli include siliceous deposits in San Bernardino County, California (USBM Minerals Yearbooks, 1934-1941) and in Nevada (Chandler, 1960). These, however, differ in composition and/or origin from tripoli and, therefore, should not be identified by the name tripoli.

Jan 1, 1983

By G. W. P. Rengstorff, R. B. Fischer

A study was made of the effect of impurities on the bend ductility of cast molybdenum. High purity molybdenum was repared by re-melting under high vacuum. The ductility of "transverse-grain" specimens indicated that intergranular brittleness decreased with an increase in purity of the metal. THE production of as-cast molybdenum with high ductility at room temperature would make working of the metal easier and increase the usefulness of the as-cast metal. Furthermore, a .knowledge of the factors that influence the ductility of as-cast molybdenum might be applied to the problem of making fusion weldments having satisfactory room-temperature ductility. Individual grains of commercial as-cast molybdenum are slightly ductile at room temperature. However, the presence of carbides at the grain boundaries may cause the metal to fracture in a brittle manner. This behavior has been discussed.' The amount and distribution of the impurities in as-cast molybdenum would be expected, from previous research on the metal, to have considerable influence on its ductility. Some effects of oxygen and carbon on the mechanical behavior of the metal were discussed by Parke and Ham,2 Woodside,3 and Zappfe. Landgraf, and Worden.4 Parke and Ham2 found that, if a sufficient number of molybdenum oxide particles were present at the grain boundaries, the intergranular cohesion was reduced to the extent that arc-melted molybdenum would rupture intergranularly during hot forging. They also found that if the oxygen content was less than 0.003 pct, the cast molybdenum was hot forgeable. It is suspected, however, that forgeable molybdenum may contain a small amount of oxide that could reduce the ductility of the as-cast metal at room temperature. Also, there is the possibility of the unfavorable distribution of other impurities having a detrimental effect on the ductility of cast molybdenum. The results of a study of the influence of purity on the room-temperature ductility of cast molybdenum are presented here. Vacuum Arc-Melting to Produce High Purity Mo One way of determining the effect of impurities on the ductility of molybdenum is to prepare and test metal as free of all impurities as possible. Accordingly, the present investigation was undertaken with this in view. Arc melting in high vacuum (less than 0.1 micron of mercury) was chosen as the method for reducing the impurities below the concentrations occurring in commercial molybdenum. Commercial arc melting of molybdenum is carried out at about 50 microns pressure. During the arc melting, carbon and oxygen in the metal react to form carbon monoxide. By virtue of the vacuum process, the partial pressure of carbon monoxide is maintained at such a low value that the reaction greatly lowers oxygen and carbon contents. An excess of at least 0.03 pct C is used in commercial arc melting to insure that the oxygen content will be below 0.003 pct. The excess carbon remaining after the deoxidation step forms carbides on freezing. Some of the carbides precipitate at the grain boundaries and, as will be shown, have an unfavorable effect on the room-temperature ductility. In the present work, only the small amount of carbon (0.003 pct) contained in the commercial powder-metallurgy molybdenum used for melting stock was present. Partial removal of oxygen from the melt probably occurred as the result of the volatilization of molybdenum oxides, or by distillation of oxygen at the high melting tem-

Jan 1, 1953

By H. F. Moore

Jan 1, 1936

By Walter Kauzmann

ALL viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.[t] Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem -i.e., the dependence of shear rates on temperature, stress, etc.-from the standpoint of recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of applications1 RESOLUTION OF MACROSCOPIC SHEAR INTO MICROSCOPIC MOVEMENTS; RESEMBLANCE TO CHEMICAL REACTIONS Just as any large body is made up of many small units, or atoms, so macroscopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for nonturbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove. In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker,4 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the

Jan 1, 1941

By C. D. Hall

This paper may be divided into two main parts: (1) analysis and data to show that Eq. 6 adequately correlates the authors' experimental data, and (2) the assertion that Eq. 20 "should permit scale-up with data taken from one pipe diameter for Newtonian, inelastic non-Newtonian, and viscoelastic fluids, such as dilute polymer fracturing fluids, which produce considerable pressure reductions." The authors might well recommend that this broad grouping of fluid types could be correlated by using Eq. 6 (requiring data from at least two pipe diameters). On the other hand, Eq. 20 is only shown to be adequate for conditions within the range of the present data set. Specifically, predictions by Eq. 20 for diameter scale-up to casing sizes would give larger deviations than implied in Table 2, and scale-up for some other fluids that give large drag reduction could be grossly in error. The description of a class of fluids "which produce a diameter family of straight parallel lines on a log (d?p/4L) vs log (8 v/d) plot. . ." defines a necessary condition for using Eq. 6; i.e., that s shall be constant for each fluid. The proposal that Eq. 20 is applicable to turbulent flow of such fluids is equivalent to saying that the spacing of these parallel lines, with A being constant, will be found to correspond to m = -1.20 for all such fluids. Table 1 shows the values of m derived from data on 16 non-Newtonian fluids. The key statement of this paper is that the diameter exponents "do not vary significantly from . . . -1.20." In statistical terms, this says that the m value for each fluid, which was obtained from all the measurements made on that fluid. has not been shown to be different from the arithmetic mean of the m values for the 16 fluids tested. This implies that the group mean, -1.20, is a more reliable value to use for an individual fluid than is the m value derived from the data on that fluid alone. No statistical test is described to support the key statement that the diameter exponents do not vary significantly from -1.20. Such a test would have to take into account that each individual m value is shown to correlate the pressure gradients for its fluid, with only about 3 percent standard deviation over the diameter range covered. That is, the m value is not the result of a single independent measurement. Thus, it would not be sufficient, or valid, to compare the deviation of one of the m values with the variance of the 16 values of m about their mean. An alternative interpretation of the key statement is that the diameter exponents do not vary appreciably from -1.20; i.e., that using -1.20 does not cause serious inaccuracy. Table 2 seems to be offered in support of such an assertion. However, such a statistical treatment (1) is unnecessary and (2) cannot lead to any valid scale-up generalization. The amount of error introduced by using a 1"wrong" value of diameter exponent — i.e., -1.20 instead of m — is determined by Eq. 6. The ratio of the pressures predicted by Eqs. 6 and 20 for scale-up from ds in small pipe to d, in casing is The pressure for 30-percent calcium carbonate slurry (m = -1.112) in 10-in. ID pipe would be predicted 30 percent higher by Eq. 6 than by Eq. 20, if based on tests in 0.5-in. ID pipe. The data set tested in Table 2 represents only a limited sample of pipe diameters (ratio of about 4:l) out of the population of diameters that would

Jan 1, 1970

By J. F. Olk, E. D. Spaulding, R. E. Thurmond, G. A. Komadina, R. W. Hernlund, J. A. Journeay

THE Pima pit is a 1700x1400-St oval, the long T axis parallel to the strike of the orebody. The north side of the pit is carried as a final pit slope that coincides with the footwall of the orebody. The south side and east and west ends of the pit are working slopes continually being stripped back toward the final slopes. An inclined roadway extending from the natural ground surface on a 5 pct grade down to the north- east corner provides access to the pit. This road enters the pit 130 ft below the natural surface and continues as a pit ramp on a 5 pct grade to the 3150-ft bench (roughly the base of the alluvial cover). At this point the ramp system is steepened to a 12 pct grade and continues to the pit bottom. The 5 pct grade is maintained in the alluvial section to facilitate scraper haulage out of the pit. In addition to this main access ramp, temporary working ramps in the alluvial areas allow shorter routes to dumps. These are left on top of working benches and do not change the overall working slopes. Below the base of the alluvium, haulage is by truck down to the skip loading point or up from the bottom to the skip loading point.

Jan 4, 1958