Search Documents

By J. G. Savins

Certain types of macromolecules added to water and salt solutions flowing in turbulent motion can reduce the pressure gradient. Alternatively, the volumetric capacity of a pipe for these fluids is increased by the presence of these materials. Examples presented show that the drag reduction can become significant. Thus, the presence of 0.28 per cent of a gum derivative in a solution of sodium chloride flowing at 200 gal/min in a 1.89-in. pipe yields a pressure drop which is 0.44 of the single-phase drop measured under the same conditions of turbulent flow; the addition of 0.1 per cent of a vinyl derivative to a I-in. water line yields a throughput capacity which is 1.78 of the single-phase capacity at the same pressure drop. It is further shown that these phenomena are distinctly different from previous observations with other classes of non-Newtonian systems. There a simple lowering of friction factors below the levels predicted from the resistance laws for Newtonian fluids is associated with a suppression of turbulent motion. A rational physical explanation for drag reduction is advanced. Briefly, the proposed mechanism is a storage by the molecular elastic elements of the macromolecules in solution of the kinetic energy of the turbulent motion. INTRODUCTION This study was inspired by a recent review of some paradoxical drag reduction phenomena in turbulent pipe f1ow.I Under very moderate conditions of turbulent flow, the pressure gradient necessary to pump solutions containing certain specific kinds of polymers, fibers and metallic soaps may become appreciably lower than that required* to pump the solvent, i.e., water or a low-viscosity hydrocarbon, under identical flow rates in the same conduit. As shown by our review, this phenomenon of drag reduction in turbulent duct flow was first noted during the second world war, apparently arising in connection with the development of flame warfare weapons. Since that time several papers illustrating this phenomenon have appeared: Toms, Oldroyd,3 Agoston et al., Bundrant and Matthews, Robertson and Mason,6 Ousterhout and Hall,7 Daily and Bugliarello~ Lummus, Anderson, and Fox. 9 That there are practical applications for techniques which increase discharge or decrease the pressure necessary to transport a liquid through a pipeline is illustrated in the patents which have issued which take advantage of this peculiar phenomenon, e.g., Mysels,l0 Dever, Harbour, and Seifert.11 One also finds fragmentary evidence of this effect in the data pertaining to a few of the polymeric solutions studied by Shaver12 and Dodge.13 However, these investigators were concerned with the development of friction factor vs Reynolds number correlations for a variety of non-Newtonian solutions and suspensions, rather than in a study of drag reduction-. A similar kind of drag reduction effect has been observed in gases. Sproull, for example, reports that adding dust to air flowing in turbulent motion through a pipe results in a lowering of the pressure gradient at identical flow rates. There are also military applications for reducing the drag on hydrodynamic vehicles. For example, the possibility of injecting a rheologically complex fluid into the boundary layers of bodies to reduce the skin friction has been investigated by Fabulal5 and Granville.16 Along somewhat different lines are the drag reduction studies of Kramer.17118 He has shown that skin friction can be reduced by covering the surface of a vehicle with a flexible skin. The effect is apparently due to the boundary layer being stabilized by the presence of the skin. Drag reduction by means of coexisting gas and liquid boundary layers, e.g., film boiling and continuous gas injection, has been proposed by Bradfield, Barkdoll, and Byrne,19 Cess and Sparrow,20'21 Sparrow, Jonsson, and Eckert.22 Here the skin friction occurs between a vapor and a surface rather than between a liquid and a surface. There are several references in the literature to friction-factor correlations for non-Newtonian solutions and suspensions: Shaver and Merri11,23 Dodge and Metzner, Clapp,25 and Thomas.26

Jan 1, 1965

By C. S. Finney, John Mitchell

The introduction of ovens for the production of metallurgical coke is believed to be due to L. L. Norton who operated an iron foundry in the vicinity of Connellsville, Pa. Persuaded by his foreman, an English immigrant named Nickols from Durham, L. L. Norton put up a 12-ft square oven which produced coke in 1833. The coal used was taken from a local mine at Mounts Creek. The oven seems to have been used in conjunction with the customary method of coking in mounds. It was in the Connellsville district also, in 1841, that two carpenters, Provence McCormick and James Campbell, formed a partnership with John Taylor, a stone mason, for the manufacture and sale of oven coke. The task of the mason was to construct the ovens, while the carpenters were to build the arks by which the coke could be taken by water to the market at Cincinnati. The following account of the enterprise was given by McCormick: "James Campbell and myself heard in some way that I do not now recollect that the manufacturing of coke might be made a good business. Mr. John Taylor, a stone mason, who owned the farm on which the Fayette coke works now stand, and who was mining coal in a small way, was spoken to regarding our enterprise, and proposed a partnership-he to build the ovens and make the coke and Mr. Campbell and myself to build a boat and take the coke to Cincinnati, where we heard there was a good demand. This was in 1841. Mr. Taylor built two ovens. I think they were about 10 feet in diameter. My recollection is that the charge was 80 bushels. The ovens were built in the same style as those now used, but had no iron ring at the top to prevent the brick from falling in when filling the oven with coal, nor had we any iron frames at the mouth where the coke was drawn. The top and mouth had to be repaired when they fell in. In the spring of 1842 enough coke had been made to fill two boats 90 feet long-about 800 bushels each-and we took them to Cincinnati down the Youghiogheny, Monongahela, and Ohio, but when we got there we could not sell. Mr. Campbell, who went with the boats, lay at the landing some two or three weeks, retailing out one boatload and part of the other in small lots at about 8 cents a bushel. Miles Greenwood, a foundryman of that city, offered to take the balance if he would take a small patent flour mill at $125.00 hi pay, which Mr. Campbell did. He had it shipped here. We tried it, but it was no good, and we sold it to a man in the mountains for $30.00, and thus ended our coke business." So successful did the coke subsequently prove to be in use that the three partners were asked to deliver more. Evidently they had had enough of the coke business, however, for they refused to have anything more to do with it. Few ovens were built between 1841 and 1855, and it is reported that in the latter year, "there were only 26 coke ovens along the river above Pittsburgh". Successful coke makers of these years included Mordecai Cochran, Richard Brookius, and Colonel A. M. Hill. It was the use of coke in 1859 in the Clinton furnace erected by Graff, Bennett and Co. in a plant on West Carson Street, Pittsburgh, that brought the real beginning of the coke-iron era in America. Here the successful use of Connellsville coke as a blast-furnace fuel was demonstrated beyond all possible doubt, and from the year 1859 the coking industry expanded tremendously. The era of beehive coke ovens During the latter half of the nineteenth century and the early years of the twentieth, the major percentage of metallurgical coke produced in the United States came from beehive ovens. It was not until 1893 that the first battery of by-product ovens came

Jan 1, 1961

By L. S. Allen, R. L. Caldwell, W. R. Mills

Borehole models used in the study of nuclear well logging are reviewed and the merit of heterogeneous us homogeneous formation simulation is discussed. .A heterogeneous model for simulating sandstone formations of variable porosity is described. Simulation adequacy was checked by steady-state and pulsed-neutron measurements. INTRODUCTION In the course of developing new methods of nuclear well logging, the problem of testing new logging instruments under controlled conditions always arises. This testing is usually done in wells of known lithology, porosity and fluid saturation, or in laboratory test facilities which simulate the borehole environment. Although the former approach is possibly more satisfying, it is frequently difficult or inconvenient to find wells with enough variation in the cited parameters for a truly comprehensive study, On the other hand. laboratow- test facilities can simulate a wide variety of formation and borehole conditions if care is exercised to maintain adequate simulation under all conditions. Workers concerned with the development of nuclear well logging methods have reported several types of research facilities in the past. Tittle, et a1 used cubical tanks filled with Ottawa silica sand to study the steady-state behavior of thermal and epithemal neutrons in simulated sandstone logging environments.1 In addition to the effects of fresh vs salt water, a wide variety of casing sizes and compositions were investigated. Tittman also used a large tank of Ottawa sand to measure the slowing down length of sio2;2 for making the same measurement in CaCO3, however, an assembly of solid Vermont marble blocks was used. More recently a very useful and carefully planned test pit for nuclear logs was constructed under the auspices of the API.3 This facility consists of three massive limestone sections, each 6-ft thick and more than 5 ft in diameter. The blocks are buried, one on top of the other, in a concrete- lined pit having a total depth of 24 ft. Each section is made of a different limestone to achieve porosity variation, the selection being Carthage (2 per cent), Indiana (19 per cent) and Austin (26 per cent). The blocks are traversed by a 7 7/8-in. diameter borehole and are saturated with fresh water. Great care was taken to insure total saturation of the stone. Homogeneous mixtures and materials have not been used exclusively for simulating earth formations. Tittle, et a1 4 showed that a heterogeneous lattice of water and graphite could be used to simulate Liquid furfural with very little effecton measured thermal and epi thermal neutron distributions. Subsequently, a lattice-type model for simulating limestone earth formations was designed and built by Berry This limestone model was constructed of 7/8- x 11/4- x 36411. marble rods glued together with a plastic resin to form a 36-x 42- x 42in. cube. The cube was honeycombed vertically with 7/8- x 7/8- x 3641-1. holes for porosity and had a 111/2-in. diameter hole in the center to serve as the borehole. Lower porosities were simulated by placing marble rods in the square holes. The finished cube was used with the borehole vertical and set in a tank to hold liquid for filling the holes in the rock matrix. A second type of heterogeneous borehole model has been proposed by Kukharenko, et a1.6= In this concept the model is composed entirely of solid material. The hydrogen equivalent of formation fluids is simulated by making the model of alternating layers of dense rock and celluloid. Additional hydrogen is included by drilling vertical holes in the rock sections and filling them with solid forms of hydrogeneous material. The volume of the holes is equal to the volume of the celluloid layers, so an axial and radial dispersion of the hydrogeneous material is thus obtained. One such model was composed of alternate 50 mm-thick sand layers and 2 mm-thick celluloid sheets. Approximately 200 appropriately spaced plastic tubes were used in each sand section. The plastic tubes were filled with paraffin for additional hydrogen concentration. This arrangement yielded a model with a water-equivalent hydrogen concentration of 10 per cent. Experimental data taken in this model and in a model consisting of the same material but homogeneously dispersed showed that the heterogeneous system adequately

Jan 1, 1966

By D. M. James, J. C. Martin

The results are presented of a study of the application of analytical methods to the solution of two-phase flow into single wells. Approximate analytical expressions for the pressure distribution in two-phase flow are found ;;; a number of conditions. The results obtained from the analytical solutions me found to be in good agreement with results obtained by finite difference techniques using a high speed digital computer. Mathematical solutions for four sets of boundary conditions are presented. All of these solutions are composed of a short-term transient plus a steady or quasi-steady state. The rates of decay of the short-lived transients are analyzed. It is found that the durations of the short-term transients may be characterized by a parameter defined as the time constant which can be determined from simple relations. It is shown also that if the outer radius is much greater than the radius of the well. the short term transients decay at rates which are proportional to the square of the exterior radius, and the rates of decay are only slightly dependent upon the radius ratio. Numerical solutions based on finite difference techniques are presented for a number of conditions. The numerical solutions are in good agreement with the predictions based on the theoretical analysis for small and moderate drawdowns. Examples involving large drawdowns indicate that the nonlinearities in the equations of flow do not appreciably alter the longevity of the short-term transients. In all cases the time required for the short-tern transients to disappear is predicted satisfactorily. INTRODUCTION The mechanism by which oil and gas flow into a single well is of vital interest to the petroleum industry. The fundamental equations of two-phase flow which describe this mechanism are nonlinear partial differential equations. Numerical solutions of these equations describing pressure transients have been obtained with the aid of electronic computers. Although solutions obtained in this manner take into account a large number of effects, the reduction of this information to useful generalities is difficult. One method of obtaining generalities is the use of linearized approximations of the nonlinear equations. Since it is possible to obtain explicit solutions of the linearized equation, general properties of the role of pressure in the flow mechanism may be ascertained. Results obtained from this approach are limited to some extent by the linearizing assumptions. The severity of these limitations may be evaluated by comparing solutions of the linear equation with numerical solutions of the more exact nonlinear equations of two-phase flow. In the past considerable amount of work has been devoted to studying pressure build-up using the single-phase flow theory. Unfortunate1y, most prep sure build-up tests involve multiphase flow. A small amount of work has been done studying pressure build-up where the flow is two-phase. The encouraging results of these studies suggest that useful results may be found from additional studies of not only pressure build-up, but also the rapid transients associated with placing a well on production. This paper presents the basic theory of the pressure transients associated with placing a well on production and with closing it in. The paper is concerned chiefly with two-phase compressible flow; however, the results also apply to single-phase flow. The results are based on analytical solutions of the flow equations, and they are verified by numerical solutions using finite difference techniques. Much of the previous work on compressible flow into wells has been confined to single-phase flow. Some work has been done on compressible two-phase steady state flow, and solutions of the equations of flow have been found by finite difference techniques using high-speed computers. Muskat1 presents some rather general solutions to the equations of single-phase compressible flow into wells. Much work has been done on pressure build-up in wells (see, for example, Refs. 2-6). Almost all of the work on pressure build-up concerns single-phase flow with the exception of Ref. 5 and part of Ref. 2. Some work has been done on pressure fall-off in injection wells.718 Muskat9 presents the solution of the equations for radial steady state two-phase compressible flow. Handyl0 extends Muskat's solution to obtain

By M. A. Grossmann

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a ''pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain sue may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of un- hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybde- num when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as wouldappear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added " 20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost lo per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome- molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By George Krauss, M. Cohen

The reverse martensitic transfomzation (i.e., the conversion of martensite to austenite on heating) was investigated in Fe-Ni alloys containing 30.5 to 33.5 wt pct Ni. The reversed austenite was found to be sufficiently distorted to exhibit marked differences in mechanical properties and to undergo recovery and re crystallization on further heating. In particular, the yield strength of the reversed austenite was as much as 2.5 times higher than that of the virgin austenite: with five cycles of the direct and reverse martensitic transformation, the yield strength was 2.6 times higher. There was an accompanying decrease in strain-hardening capacity and in stable ductility or uniform elongation. The recrystallization was observed to follow sigmoidal kinetics, but was characterized by an abnormal1y large temperature dependence which was evidently due to carbon segregation at the migrating grain boundaries. Upon recrystallization, the strength Properties reverted to those of the virgin austenite, but the ductility did not fully recover until the annealing temperature was further raised to dissipate the carbon segregation at the grain boundaries. The transformation of reversed austenite to produce second-generation martensite resulted in an unusually imperfect structure, thereby leaditg to additional strengthening. Horlleuer, the martensitic phase was much less responsive in this respect than was the austenite. MOST martensitic transformations are capable of undergoing a reverse transformation back to the austenitic phase on heating.&apos; This reaction, like the direct transformation to martensite on cooling, is usually athermal. In analogy with the Ms andMf temperatures for the martensitic transformation (where M, > Mf), the reverse transformation is characterized by the As andAf temperatures (where As<Af). It is well-known that the finish (Af) of the martensite-to-austenite reaction on heating may occur at a temperature where austenite is not stable relative to other phases in the equilibrium diagram.&apos; Reverse martensitic transformations have been found to influence the properties of the parent austenitic phase in a number of ferrous alloys. The austenite thus produced after one or more reversals is significantly altered in strength, microstruc-ture, diffusivity, and annealing characteristics compared to well-annealed, virgin austenite. The first detailed observations of such phenomena were made by Wasserman3 on an Fe-30 wt pct alloy. He found that the reversed austenite (i.e., austenite formed by the reverse martensitic transformation) was much stronger than the original austenite, and the second-generation martensite (i.e., martensite produced from the reversed austenite) was somewhat stronger than the first-generation martensite. On heating the reversed austenite, recrystallization occurred in a manner similar to that of a cold-worked metal; the Laue spots sharpened and the strength decreased.4 In recent years, Russian workers have shown considerable interest in these reverse martensitic transformations. Most of such investigations5-10 have been concerned with the stabilization of reversed austenite relative to subsequent martensitic transformation, and because of its unusual nature, this phenomenon will be discussed in detail elsewhere." On the other hand, the annealing behavior of reversed austenite and the attendant variation in properties have received little attention beyond the experiments of Wasserman.3,4 Gridnev eta1.,8 in one of the few such studies. followed the hardness change of reversed austenite as a function of time at three annealing temperatures. The marked strengthening of austenite achieved by the reverse martensitic transformation has been referred to as "transformation strengthening" by Wasserman3,4 and as "phase hardening" by Malyshev et a1.7,9,10 to differentiate it from hardening produced by cold working. Both groups of investigators noted that further strengthening of the austenite could be attained by repeated or cyclic transformations, but the first cycle resulted in the most pronounced effect. Evidence of the altered microstructure of reversed austenite has been reported by Maximova and Nikonorova6 and by Edmonson and KO.12 The former found that reversed austenite was much more sensitive to etching than the original austenite, and the latter authors observed a (&apos;ghost" structure resembling martensite in certain areas of the reversed austenite. Enhancement of the self-diffusion rate in reversed

Jan 1, 1962

By M. A. Grossman

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of unhardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of o.-2o per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as would appear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.2o per cent Mo provides a factor of 1.63, an increase of over 6o per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater harden ability will be obtained by using, for example, o.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By S. A. Levy, J. D. Wood, J. F. Libsch

A study of the preparation and characteristics of a sevies of Fe-C-N alloys has been conducted. X-ray, microhardness, and metallographic data from a series of single-phase alloys produced by controlled nitriding of carburized foils are reported. The existence of a, y&apos;, and E carbonitride has been confirmed and it has been found that y&apos; is the hardest of these three phases. These results have been used to interpret the structures observed in nitrided steels. ThIS paper represents the second phase of a three-part study concerning combined nitriding and induction hardening. The first part&apos; reports the engineering properties (depth hardness, fatigue, corrosion, and tempering resistance) obtained when seven different steels were subjected to the combined surface hardening treatment. The present paper concerns the nature of a series of single-phase alloys prepared by controlled nitriding of carburized foils. The objective was to simulate the various layers present in the as-nitrided steels. A third paper will report data concerning induction hardening of the foils and will attempt to set forth a mechanism for the high hardness obtained with the combined treatment. Studies of nitriding generally fall into three categories. The first were performed with bars using conventional nitriding procedures, thus yielding a nitrogen gradient and a series of phase layers near the surface.2-6 Such studies were complicated by the presence of the nitrogen gradient, for it was difficult to correlate microhardness and X-ray data with chemical composition. There were always complications due to penetration of the X-ray beam which yielded data influenced by underlying layers. Similar difficulty was experienced in taking hardness readings on a tapered specimen or in isolating various layers by machining. A second group of investigations was primarily concerned with establishment of regions in the Fe-N7,9,10 or the Fe-C-N phase diagram.8 These were performed with powder specimens which were nitrided in am-monia-hydrogen mixtures to produce a series of single-phase specimens. Unfortunately, the powder specimens were not amenable to either microstruc-ture or microhardness study. The third was essentially a compromise of the first two. Bose and Hawkes," using 0.005-in.-thick iron foils, were able to obtain microhardness, microstruc-ture, composition, and X-ray data on Fe-N alloys of eutectoid composition by equilibration in ammonia-hydrogen mixtures at 1290°F. To obtain a better understanding of the nitriding process and the characteristics of the phases in ni-trided plain carbon steels, the present investigation was undertaken. The investigation was patterned after that of Bose and Hawkes with the exception that nitriding was performed at 930°F (below the eutectoid temperature), as in the case of conventional nitriding. In addition to gaining some understanding of the source of high hardness of nitrided and induction-hardened steels, found in a previous study,&apos; this investigation was concerned with the possibility of controlling the phases present in a nitrided case through the use of ammonia-hydrogen mixtures. Knowledge of the properties of each phase and the conditions necessary for its production could make it possible to avoid undesirable surface layers in nitriding. EXPERIMENTAL PROCEDURE Specimen Preparation. A specimen thickness of 0.005 in. was selected to insure that a uniform nitrogen concentration could be obtained in a reasonable length of time by equilibration in an ammonia-hydro-gen atmosphere. The starting material was a vacuum-cast ingot of pure iron, the major impurities of which were: C, 0.003 pct; 0, 0.014 pct; S, 0.004 pct; N, 0.003 pct.* &apos;Compositions are quoted as weight percent except as noted. The ingot was heated to 1500°F in a nitrogen atmosphere and forged to a slab 0.25 in. thick. The material was then reduced to 0.005 in. by alternately cold rolling and annealing in a nitrogen atmosphere at 1600°F. This material was divided into five groups of specimens which, after carburizing, yielded the following carbon contents: 0.003, 0.28, 0.36, 0.46, and 0.74 pct C. The carburizing was performed by the Leeds and Northrup Research Laboratories, using a controlled "carburizing potential" which yielded a uniform carbon concentration throughout the cross section.

Jan 1, 1970

By William G. Pariseau, H. Douglas Dahl

Recent subsidence legislation indicates that mining engineers would be welt advised to be able to predict and control surface damage caused by mine subsidence. To date, such an ability is practically nonexistent. Model analysis is suggested as one of the alternative paths available which might yield fruitful results. Similitude requirements developed for a self-loaded body in static or quasi-static equilibrium indicate that complete similitude without centrifuging is an impracticability. However, a pilot experimental study which used a simplifying assumption to correctly model mine subsidence has produced results in qualitative agreement with field observations. The purpose of this paper is to present a discussion of the various approaches that can be taken in the study of mine subsidence phenomena. Particular attention is focused upon the rational selection and use of laboratory models. Broadly interpreted, mine subsidence is the deformation of the rock mass enclosing a mine. Depending upon a number of factors, the movement of the subsiding rock mass may disrupt gas and water lines or other buried utilities, damage surface structures such as buildings and bridges, dislocate streams, roads, and rail lines, aggravate acid mine drainage and fire problems, and generally mar the landscape. It is clearly a problem that no mine manager can safely ignore. It is also a problem that will grow with the general population increase. In the following discussion, a summary review of past and present approaches to subsidence studies is given. The possibilities of duplicating subsidence phenomena in laboratory models are examined, and an analysis of a particular type of model is presented. Some preliminary results obtained from a model of the particular type analyzed are then discussed. REVIEW OF PREVIOUS WORK Historically, subsidence investigations have been empirical studies in the field and laboratory or theoretical analyses of mathematically idealized media. Empirical and theoretical work in the United States has generally lagged behind investigations abroad. In the United States, field studies are mostly pre-World War 11. These are summarized in the Mining Engineer&apos;s Handbook. &apos; Field studies in Europe are more recent and more extensive. Those made in Great Britain are summarized in the Subsidence Engineers Handbook2 and represent observations made at 157 different collieries. Such studies by themselves are of limited usefulness as are all empirical studies. One can never be certain that conditions at one mine will be similar enough to those at another to warrant the drawing of like conclusions. European subsidence formulas rely heavily upon the "angle of draw" and "critical area" concepts. The angle of draw is defined as the angle between a vertical line through the face, and another line extending from the face to the surface at the point where movement is zero. The critical area is defined in relation to the least extraction necessary to produce maximum subsidence. Fig. 1 illustrates the angle of draw and critical area concepts. First and second "limits of influence" are also shown. The angle of draw and associated critical area concept are obviously not well defined, being dependent upon the accuracy of the surface survey. In Great Britain, the angle of draw has increased through the years from about 26 to 35°. In the United States, zero and negative angles of draw have been reported. In the authors&apos; opinion, these purely geometrical concepts represent an oversimplification of subsidence phenomena and their use, in the United States at least, should be discouraged. Empirical observations of laboratory models containing layers of earth, sand, clay, and plaster were made by Fayol (cited by Peele) as early as 1885. An outgrowth of his work was the "dome theory," a verbal description of what is assumed to occur in subsiding rock masses. The dome theory has since fallen into disrepute. Theoretical analyses worthy of the name treat a subsiding rock mass as a deformable body. In these analyses, the actual rock mass is replaced by an idealized material that deforms according to a simple stress-strain relationship. The stress equations of equilibrium expressing the Newtonian laws of mechanical action and the geometry of strain furnish additional equations that must be satisfied. A loading criterion-generally understood, and in some cases stated explicitly-completes the theory.

Jan 1, 1969

By M. Marciano, K. Kreider

Silicon carbide coated boron fiber (Borsic) reinforced aluminum composites were made which exhibit strength and modulus values predicted by the rule of mixtures. A successful technique for fabricating these composites consists of plasma spraying of monolayer filament reinforced tapes and subsequent diffusion bonding of these tapes into composites. The elastic properties of the composites were given by the rule of mixtures in reinforced directions. (The modulus parallel to the fibers was 32 x 106 psi for a composite with 50 pct by volume fibers. The other elastic properties for a composite with 50 pct fiber were transverse modulus = 14 to 16 X 10 psi, G = 9.5 x 106psi, and v,, = 0.23. Tensile strengths of over 190,000 psi were measured for the composites with 50 pct fiber and the average strength for these composites was 162,000 psi. These same composites had interlaminar shear strengths of 12 to 15,000 psi. Multidirectionally reinforced composites demonstrated the same reinforcement efficiency in strength and modulus as the uni-directimlly reinforced composites. Comrpessive strengths of composites with 50 pct by volume fiber were found to be greater than 250,000 psi. STRUCTURAL filamentary composite materials are being considered for use where high strength, high modulus, and lightweight materials are required. Metal matrix composites have been considered for use at temperatures ranging from cryogenic (aluminum stainless steel) to 6000°F (plasma sprayed tungsten plus tungsten fiber) and other requirements have been similarly diverse. Metal matrix composites offer high modulus and high strength in unreinforced directions, the ability to be joined by brazing or welding, and greater fracture toughness compared with the more easily fabricated resin matrix composites. This paper deals with the mechanical properties of aluminum boron composites, a system which is being considered for applications where lightweight, high modulus, and high strength are required at temperatures including those above the normal operating temperatures of resin composites. The boron fiber used in this investigation had an average room temperature strength of greater than 400,000 psi, a modulus of 58 x 106 psi, and a density of 0.09 lb per cu in. (2.6 g per cu cm).&apos; The fiber used in the composites had a coating of silicon carbide to retard degrading reactions with the matrix at elevated temperatures. The coated fiber, which is sold commercially as Borsic: has been reported to have excellent resistance to degradation at temperatures up to 600°C in air and in aluminum2 and the same mechanical properties as the standard bare boron fiber. Fabrication of Composites. The composites were diffusion bonded from plasma sprayed monolayer tapes. These tapes were fabricated on a substrate of aluminum alloy foil which is incorporated in the composite matrix. The technique consists of winding a layer of fiber on the foil, and plasma spraying the balance of the matrix alloy over the windings which bonds all of the components together. Advantages of this process include the ability to achieve good fiber spacing, Fig. 1, the formation of a good bond between fiber and matrix (achieved during the plasma spraying), and the adaptability of the process for forming large and complex parts. This is particularly true when used with brazing foil backing which alloys low pressure bonding of the structural shape. PROPERTY EVALUATION TECHNIQUES Tensile test specimens, 5 to 7 in. long with a reduced gage section and ,030 to ,040 in. thick, were cut from composite sheets with a diamond saw. The gage section was .200 in. wide, while the gripped section was .240 in. wide and over 2 in. long in each grip. The standard gage length used was 1 in., however, transverse specimens (i.e., specimens with the fibers oriented 90 deg to the loading axis) were tested without a reduced section. Twelve specimens were also made with a 3-in. gage length but no significant effect of gage length was measured. The tensile test specimens were mounted in a fixture and aligned in friction grips using a 10X microscope. Unbonded foil doublers (0.010-in.-thick aluminum) were used to insure firm gripping with a minimum of damage to the fibers. The test specimens were transferred to the testing machine in a rigid fixture and mounted in the self aligning loading train. Testing was performed using a Tinius Olsen four screw testing machine with a torsion bar LVDT load

Jan 1, 1970

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

Binary alloys of titanium with silver, lead, tin, nickel, copper, beryllium, boron, silicon, chromium, molybdenum, manganese, vanadium, iron, and cobalt were studied. One-half-pound ingots of the alloys were prepared in an arc furnace, employing a water-cooled copper crucible, an argon atmosphere, and a water-cooled tungsten electrode. The half-pound ingots were fabricated by forging at 1700°F in air to 1/4-in. slab, followed by hot rolling at 1450°F to 0.060-in. sheet. Tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships were determined for these alloys. EARLY in 1947, as one phase of the evaluation of materials for Air Force Project RAND, Battelle successfully arc melted Bureau of Mines titanium and obtained a few basic properties of unalloyed titanium and several titanium-base alloys. The low density, excellent resistance to corrosion, and high tensile properties of these materials stimulated a great deal of interest among metallurgists and designers seeking better materials of construction. As a result of this early work, Battelle, under contract with the Air Materiel Command, Wright-Patterson Air Force Base, has continued extensive studies of titanium alloys. The result of the first year&apos;s work is described in three papers. The present one deals with binary alloys, the second with ternary alloys, and the third paper with quaternary alloys. Melting Method The arc furnace for melting titanium and other refractory metals was developed at Battelle Institute under Air Force Project RAND. During the present work, considerable improvement has been made in the design and operation of this furnace for making small ingots of titanium and titanium alloys. The improved furnace design is illustrated by fig. 1, which shows a cross-sectional view with the dimensions of various parts and their relationship to one another. The essential features of the furnace are the inert argon atmosphere, the water-cooled copper crucible, and the water-cooled tungsten elec- trode. The melting crucible is formed by spinning 0.064-in. annealed copper sheet. A groove for an O-ring seal is spun into the flange of the crucible. A fiber gasket between the crucible flange and the water-cooled brass cover provides electrical insulation. The brass cover is fitted with a sight glass, an opening for the water-cooled electrode, and a tube through which the material is charged. Direct current is used for melting, with the positive electrical terminal connected to the water jacket and the negative terminal to the electrode. A typical heat is made in the new furnace as follows: Approximately, 0.20 lb of titanium under 2 mesh per in. and the alloy addition, if any is to be used, are placed in the bottom of the crucible. The cover is clamped on the crucible so that the O-rings make a tight seal. The remainder of the charge is placed in a glass bottle, and this is connected by a rubber hose to the charging tube of the furnace. The crucible and the charge are evacuated with a mechanical pump to a pressure below 50 mm of mercury, or less if desired, and held at this reduced pressure for 5 min. Hot water is circulated through the jacket during the evacuation period to assist in outgassing the crucible. Following the evacuation, tank argon of 99.92+ pct purity is flushed through the crucible for 5 min and then adjusted to give a positive pressure of 1 to 2 psi. During subsequent operation, an argon pressure regulator introduces only enough argon to compensate for the small leakage which occurs through a mercury trap. Re-evacuation and reflushing the melting chamber with argon produced a negligible reduction in contamination. Two 550-amp generators, connected in parallel, constitute the power source. Normally, about 800 amp are used for melting alloys which are not extremely refractory. The generators are set for 90 v open circuit and 200 amp. The arc is struck and the electrode is withdrawn to produce an arc of 23 to 26 v. This voltage is maintained while the electrode tip is moved slowly around a circle 1 in. smaller than the diameter of the ingot. The current

Jan 1, 1951

By Walter E. Lewis

Myriad problems face all of us in the next decade. Vietnam, poverty, and pollution are perhaps the most pres- sing. A lesser one but still vital to us as a Nation is the slow hut apparently relentless extinction of the mining, metallurgical. geological and petroleum engineer. Are we doomed to take our place in the crossword puzzle with the moa. to be defined like it as an "extinct bird"? Or can we reverse the trend perhaps, in the next decade? The plain fact is we are an endangered species, and must resign ourselves to virtual extinction in the 1970&apos;s unless the trend is reversed. Probably, many of us have felt the problem will solve itself if left in the in-basket long enough, believing, that the trend will reverse solely on the basis of demand for these disciplines. This approach has not worked up to now, it gives no promise of working in the future, and furthermore, the problem has been in the in-basket much too long. The point is simply this: What can each of us do as an individual, or as part of a company, a State agency, a Federal agency, a university, or an organization such as AIME?

Jan 1, 1970

By AIME AIME

In the uniform of his country for the second time, Harry Phillip Stolz. Chairman of the A.I.M.E. Petroleum Division, holds a commission as Lieutenant-Commander in the Naval Reserve and is attached to the office of Inspector of Naval Petroleum Reserves in California. During World War I he left his studies at Stanford University to join the Army and was granted a commission as Second Lieutenant of Infantry. He remained in the Army Reserve until 1938 when he resigned to accept a commission as a member of the Naval Petroleum Reserves Advisory Board. Born in San Francisco Jan. 29,1899, where his father had lived since 1880, he was in that city during the turbulent year of 1906 where the city was ravaged by fire and earthquake.

Jan 1, 1942

By AIME AIME

CHARLIE WARNER, Chairman of the Petroleum Division, is no stranger to the problems of the oil industry or to those of the Petroleum Division, after more than 25 years of experience in locating and producing oil and more than 22 years of membership in the Institute. He was born at Jefferson, N. Y.. April 27, 1894, and educated in the public schools of New York State and at Cornell University where he studied geology and allied sciences from 1913 to 1917 and received a B.A. degree. Immediately upon completion of this training, he was employed by the Empire Gas & Fuel Co. as a field geologist in Oklahoma and Kansas. Two years later he became district geologist for the Emerald Oil Co. in Oklahoma and Kansas, and in 1920 he rejoined the Empire Gas & Fuel Co. in the capacity of district geologist in Oklahoma. In September of 1921 he began his association with the Houston Oil Co. of Texas. He was district manager for the company in the Mid-Continent area until 1932 when he was transferred to the head office at Houston, where he became superintendent of the land and lease department in 1934 and was elected a director of the company in 1941. In these capacities, and also as petroleum engineer for the company, he keeps in intimate touch with all phases of field activity and with the regulation of the industry by State and Federal agencies.

Jan 1, 1943

By J. E. Tobey

UNDER war conditions coal immediately assumes a position of highest importance for coal must carry the basic load for industry. The upward trend in production continued through 1941. Bituminous coal production alone about equaled the total output of bituminous and anthracite in 1940. The figures for 1941 approximated 500,000,000 tons for bituminous, and 54,000,000 tons for anthracite, and production of by-product and beehive coke exceeded that of the previous year. The coal industry, under the National Bituminous Coal Act, is going through a period of readjustment, and is beginning to stabilize itself under the statute. The Federal Mine Inspection Nill became law during the year.

Jan 1, 1942

By S. Terry, W. Callender, R. J. Cornelius

When a dry ball-mill grinding circuit was in- stalled at the pellet plant of Hamersley Iron Pty. Ltd., it was something of a pioneering venture, since this was one of the first instances where such a circuit had been applied to iron ore on a major scale. The Hamersley pellet plant is located in Dampier on the coast of Western Australia. The feed for it consists of -8mm fines produced as a screened product at the Mt. Tom Price mine 186 miles inland from Dampier. It was these fines that encouraged the choice of a dry grinding facility for the plant. At the outset, tests had shown that the fines could not be filtered satisfactorily with a wet grinding system. At the pelletizing plant, the fines are stockpiled, reclaimed, dry ground in ball mills, formed into pellets on balling discs, hardened on an indurating line, and stockpiled for shipment overseas. These operations are shown in Fig. 1.

Jan 7, 1969

By AIME AIME

FOUK fields of activity are now recognized by the A.I.M.E. in its award of medals for conspicuous achievement: the Saunders medal for mining, the Douglas medal for non- ferrous metallurgy the Lucai medal for petroleum, and the Rand medal for distinguished achievement in the broad field of mining administration including the organization and development of enterprises in all branches of the mineral industry. This last is known officially as the Charles F. Rand Memorial Medal, and it award is made possible through funds supplied by the Charles F. Rand Foundation. Until this year money thus available was used for other special projects, so that the forthcoming presentation of the Rand medal to Robert C. Stanley is notable as being the first time that achievement in mining administration has been thus recognized.

Jan 1, 1940

BECAUSE of the impetus given to placer mining since the price of gold was advanced to $35, several types of small dredges have made their appearance, especially in the Lincoln and Oroville areas of California. Some of these are known as "doodle bugs," and have been given considerable publicity, though many believe their performance has been overrated and that complete costs of construction and operation, if known would not put them in so favorable a light. Fig. 1 is a doodle bug owned by E. M. Clark and operated near Lincoln, Calif. It is understood that it was abandoned because of inability to handle deep ground. A similar machine that has been operated-profitably by Comstock Placers is shown in Fig. 2.

Jan 1, 1938

By AIME AIME

As already announced, the XCIIId meeting of the Institute will be held at Toronto, beginning July 23, 1907. Hotel Headquarters will be at the King Edward Hotel, in which also the sessions will be held. The Queens, Rossin, Wallen, Iroquois and Palmer are good hotels not far from the King Edward. Members must secure their hotel-accommodations beforehand, by direct correspondence with the hotel they select. For those who neglect this precaution, the Local Committee will doubtless do what it can, but is unable to promise anything. Correspondence concerning this meeting (including notices of intention to attend it) should be addressed hereafter exclusively to Mr. W. G. Miller, Provincial Geologist, Bureau of Mines, Toronto, who is the representative of the Local Committee. The excursion to Cobalt, Lake Tenagami, Sudbury, etc., arranged by that Committee, involves the use of a special Pullman train for meals and lodging. After waiting a reasonable time to hear from members, the Local Committee has made its contract for Pullman cars. According to its latest report, there was still room for additional excursionists. Under this head, application made immediately to Mr. Miller may not be too late. Sessions for the presentation of papers, etc., will be held at the King Edward Hotel on Tuesday afternoon, July 23, and Wednesday morning and afternoon, July 24. The following papers have been accepted: 1. Sonic Reflections on Secrecy in the Arts, by James Douglas, New York, N. Y. .2. The Wilfley Table, by R. H. Richards, Boston, Mass. 3. The Tar-Sands of the Athabaska District, by&apos; Robert Bell, Ottawa, Can. 4. The Occurrence of Nickel in Virginia, by Thomas L. Watson, Blacksburg, Va. 5. Coal-Briquetting in the United States, by E. W. Parker, Washington, D. C.

Jul 1, 1907

By Murl R., Schrock

THE use of diamond-drill holes at the Moctezuma Copper Co., Pilares mine, Pilares de Nacozari, Sonora, Mexico, for the ventilation of raises has resulted from experiments that were made in an effort to secure continuous and efficient ventilation in hot and gaseous raises. The method is particularly applicable in long raises and in raises run from development levels where the source of fresh air is distant. In order that the CO, concentration shall not become excessive, 30 cu. ft. per min. per man must be supplied to a heading for breathing purposes:&apos; The quantity of air that will pass through a diamond-drill hole by

Jan 1, 1929