Search Documents

By E. L. Kinsella, F. S. White

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By F. S. White, E. L. Kinsella

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By R. B. Walker, R. Palmer, L. C. Bryner

The purpose of this investigation was to further study some of the factors affecting the air oxidation of sulfide minerals. Data obtained from laboratory studies on the effect of temperature, concentration of iron salts, pH, and other catalysts on the biological and nonbiological oxidation of sulfide minerals are presented. The oxidation of copper sulfide minerals and subsequent leaching of the soluble copper has long been a profitable operation. The chief oxidizing agent is oxygen from the air. This reaction is influenced by a number of different factors such as temperature, light, hydrogen ion concentration, oxidizing agents, and various catalysts. Sullivan1 found that copper sulfide minerals are slowly oxidized by the air and that dilute sulfuric acid and iron (111) increased their solubility. At that time it was not known that bacteria were involved in the oxidation of the sulfide minerals. It has been shown that pyrite, molybdenite, free sulfur, and the copper sulfide minerals found in the waste rock dumps in Bingham Canyon, Utah, are largely oxidized by chemosynthetic autotrophic microorganisms found in the leaching streams.2-6 Similar organisms have been isolated in other mining areas7,8 and from the effluents from coal rnines.9 The following are some of the questions that have arisen regarding the mechanisms of the reactions involved in the leaching process. How dependent is the leaching operation upon the biological reactions? How does the temperature effect the biological and non-biological reactions? How does the concentration of iron (II) and (111) effect the rate of oxidation of copper (II) sulfide? Does the iron act as a catalyst? Does activated carbon act as a catalyst on the oxidation of sulfide minerals? What effect does the hydrogen ion concentration (pH) have on the above reactions? The purpose of this paper is to report the results of laboratory studies on these problems. EXPERIMENTAL The apparatus used in this investigation was an air lift percolator described in our earlier work.' The percolator consisted essentially of an air lift which enabled the leaching solution and microorganisms to pass freely through a suspension of mineral (substrate) in Ottawa sand. The air lift served the additional purpose of maintaining an ample concentration of oxygen and carbon dioxide in the nutrient (leaching) solution. (See Fig. 1.) The percolators were so constructed that they could be immersed in liquid constant temperature baths for temperature studies. The thermostats were controlled to +0.5°C. The reactions were all run in the dark. The percolators were charged with one to three g of mineral, dispersed in 100 g of Ottawa sand and 100 ml of nutrient or leaching solution. The sand was purified to remove traces of iron by digesting with concentrated hydrochloric acid and washng with distilled water until free from chloride. After drying, the sand was ready for use. The compressed air supply was regulated to 5 psi and bubbled through an aerator containing distilled water, which was maintained at the same temperature as the bath used. The air was filtered through cotton plugs to maintain sterile conditions. The tops of the

Jan 1, 1968

By John M. Kelly

New Mexico produced 39,475,388 bbl. of oil in 1944, the greatest amount in one year in the oil history of the state. This production was 593,046 bbl. or 1.25 per cent more than in 1943. New Mexico retained its position as the seventh largest oil-producing state. The maximum per well allowable on Jan. I, 1944 was 48 bbl. daily and at the end of the year it was 45 bbl. daily. Allocations as set by the New Mexico Oil Conservation Commission closely followed the recommendations made by the' Petroleum Administrator for War. The average daily pipe-line runs were within 4 per cent of the allocation. Production by counties was as fol1ows;Lea County, 33,509,548 bbl.; Eddy County, 5,504,498; Northwestern New Mexico 461, 342. Drilling activity for New Mexico in 1944 was well above that of 1943, with 362 completions. Of these, 283 were oil wells, 12 gas wells and 67 dry holes. The ratio of dry holes to producers, about I to 4, was an improvement over 1943. Wildcat drilling during 1944 was responsible for the discovery of six new fields and the extension of two present producing areas. Drilling records were established in New Mexico during 1944 with the deepest producer ever completed, the Humble Leonard Oil Company's No. I at 11,969 ft., in the Ellenburger section of Ordovician age near Jal, Lea County. The discoveries in Lea County during 1944 were as follows: West Lovington field, where Fred Turner, Jr. drilled his No. I State B .in C SE SW sec. 4-17-36 and completed it for 122 bbl. of oil in 8 1/2 hr., in the San Andreas section of Permian age. The Tonto field, where the T-exas Company completed its No. I Baskin at a total depth of 3586 ft. in Seven Rivers lime of Permian age, with an initial production of 254 bbl. of oil in 21 hours. The Drinkard area, where the Gulf Oil Corporation's Drinkard No. I flowed 782 bbl. of oil in 14 hr. from the Yeso section of lower Permian age, thus opening the first lower Permian production in the state. The total depth of this discovery was 6508 ft. and oil was 38.8" A.P.I. gravity. The Dublin area, where the Humble Oil and Refining Co. established a drilling depth record of 11,969 ft. drilling and completing its No. I Leonard Oil Co. well in the Ellenburger lime of Ordovician age. This well flowed 221 bbl. of oil per day, of 48.9º A.P.I. gravity oil. It is in sec. 12-26-37. The new pay horizon discovery of the Continental Oil Co. in the Skaggs area, where the company completed its Skaggs B-23 No. 2 in sec. 23-20-37 for 236 bbl. of oil in 21 hr. from the Wolfcamp section of lower Permian age, at a total depth of 7725 ft. This well was drilled to granite at 10,465 ft. and plugged back to the Wolf-camp for a new pay zone completion.

Jan 1, 1945

By D. C. Porterfield

ProUuction of crude oil in Venezuela increased from 186,134,000 bbl. in 1940 to 2~8,131,ooo bbl. in 1941, or 22.6 per cent, to establish a new all-time high for the country. While the average production for the year was 625,000 bbl. per day, production during the month of December 1941 averaged 751,000 bbl. per day, and during the last week of the year, 766,000 bbl. per day. Production from the Lake Maracaibo basin averaged 454,000 bbl. per day during the year, or 72 per cent of the total for the country, compared with 73 per cent of the total produced in 1940. Drilling during the year was approximately on the same scale as in 1940, with 438 wells completed in 1941 as compared with 429 the year before. Exploratory completions decreased from 18 in 1940 to 6 in 1941. Of the drilling operations in 1941, 56 per cent was concentrated in the Lake Maracaibo basin and 44 per cent in eastern Venezuela, success being 98 per cent in the Lake basin and 83 per cent in the east. Successful completions for the country as a whole amounted to 92 per cent of the total wells drilled. Exploratory drilling in 1941 resulted in the discovery of three new fields, all in eastern Venezuela; viz., Guara, about II km. to the northeast of the Oficina field but on a separate structure; Santa Rosa, which is east of El Roble field on a structure forming a part of the major Santa -Ana- San Joaquin-El Roble uplift; and Santa Barbara, which is southwest of the Jusepin field on an extension of the main Jusepin anticline. At the close of the year three wildcats were drilling, all of which showed prospects of obtaining production; that is, Mercedes No, 2 in central Guarico, Las Ollas No. I on the Anzoategui-Guarico border near the town of Zaraza, and Quiamare No. I in Anzoategui northeast of the town of San Mateo. In spite of heavy withdrawals and the resultant natural decline in the potentials of older producing areas, new drilling during the year increased the potential production of the country from an estimated 780,000 bbl. per day at the end of 1940 to an estimated 810,000 bbl. per day at the end of 1941, or approximately 4 per cent. Since domestic consumption of petroleum products is insignificant compared with total production, exports of crude and products during the year increased in line with production. Crude exports totaled 196,800,000 bbl., compared with 158,400,-000 bbl. in 1940, and exports of products were 26,100,000 bbl., compared with 21,900,000 bbl. the year before. Exports of crude from Venezuela to the United States amounted to 36,500,000 bbl. In addition, about 2,200,000 bbl. was imported in bond into the United States for transfer to Canada. Total refining capacity of the country in 1941 was approximately 125,000 bbl. per day, including a crude-conversion plant with a capacity of 32,000 bbl. per day, capable of making fuel oil only. Three plants with a capacity of 121,000 bbl. Per

Jan 1, 1945

By R. S. Kinasevich, D. D. Crabtree, D. W. Fuerstenau, T. P. Meloy, A. L. Mular

The effect of such variables as feed size, particle shape, cleavage, and hardness on the relative proportion of impact, abrasion, and chipping events in a tumbling mill is demonstrated. The concept of an average event, which is a combination of the three comminution mechanisms, is introduced. It is postulated that the average event in a particular mill determines not only the size distribution but also the energy-size reduction relationship for the comminution process. Fragmentation of particles in tumbling mills appears to result from a combination of impact, abrasion, and chipping grinding.' The relative rates of size reduction attributable to any of the basic grinding mechanisms must depend upon a number of variables, such as feed size, particle shape, hardness, and the number and kind of particles in the mill. The purpose of this paper is to show experimentally how these variables in the properties of materials affect the size distributions obtained by grinding the material's in a laboratory tumbling mill. The resulting size distributions will be intetpreted in terms of a combination of three comminution mechanisms. METHODS AND MATERIALS In this study, minerals of widely differing properties were ground either separately or as mixtures in laboratory mills using rods or balls for grinding media. The materials used include quartz, Tuolomne, limestone (99.8% CaCO3), barite, corundum, galena, pyrite, glass beads, and crushed glass. The mill used was 8 in. in diam. and 9-1/4 in. long. For the ball milling tests, 17.6 kg of steel balls (36: 7/8 in. balls, 178: 1 in. balls, and 44: 1-1/8 to 1-1/4 in. balls) were used. For the rod milling experiments, 17.6 kg of steel rods 9-1/16 in. long (25: 5/8 in., 10: 3/4 in., and 5: 7/8 in. in diam.) were used. In each test, 1 kg of solids were ground wet at 60% solids at 77 rpm. In all cases except where otherwise specified, the feed to the mill was 4 x 8 mesh material. Size distributions of the ground products were determined by a wet-dry sieving procedure with Tyler series sieves. Size distributions of mixed products containing limestone were determined by dissolving the limestone with acid and sizing the residue. EXPERIMENTAL RESULTS AND DISCUSSION If the size distribution of the product from a tumbling mill depends upon the relative proportion of impact and attrition (abrasion and chipping) events, altering the grinding conditions may change these proportions and consequently alter the size distribution of the product. Data to illustrate this point can be taken from Gaudin's classic 1926 paper.2 In one series of experiments, Gaudin ground quartz of different initial sizes for four hours in a laboratory ball mill with 7/8-in. balls. In Fig. 1, his data are reproduced as the cumulative fraction finer than the stated size for the following initial feed sizes: 13.3 x 9.4 mm, 6.7 x 4.7 mm, 2.6 x 1.6 mm, and 0.83 x 0.59 mm. As the feed size was decreased, a dramatic change in the shape of the size distribution curves took place, even though the amount of minus 100-mesh

Jan 1, 1964

By Alec M. Crowell, J. W. Sanders

While the production of crude oil and condensate in South Arkansas increased only 1.7 per cent over the 1940 figure, complete utilization of gas produced with the oil and condensate, and heretofore wasted, was beginning to be evidenced. There were 26,229,264 bbl. of oil and condensate produced in South Arkansas during 1941, as against 25,790,380 bbl. for the year 1940. (Fig. I.) Since 1936, deep producing sands have been discovered in 18 fields and during that period only 40 per cent of the total state production has come from Upper Cretaceous formations while 60 per cent came from the Lower Cretaceous and Jurassic formations. The gas produced with crude oil and condensate from the latter formation contains large quantities of hydrogen sulphide, the maximum being 6900 grains per 100 cu. ft. in the Patton pool of Lafayette County. Gas Utilization During the latter part of 1940 and the early part of 1941, pilot plants were placed in operation to determine whether the hydrogen sulphide and deleterious material in South Arkansas gases could be removed economically. The Federal Government desired to build a large aluminum plant in the Ouachita Valley and was seeking cheap fuel for the generation of electricity. The fact that the gases were produced with appreciable quantities of crude oil and condensate made it available at a very low price, since the state's conservation law prohibits the flaring of any gas. As a result of these experiments the first large-scale unit for the processing of gases containing hydrogen sulphide was placed in operation on Sept. I, 1941. The plant is in the Magnolia oil field, Columbia County. It processes residue gas from the Shell Oil Company's gasoline plant in that field and also raw gas from the Village field, 6 miles east of the Magnolia field. The gas entering the desulphuri-zation unit is laden with approximately 1400 grains of hydrogen sulphide per 100 cu. ft. and is stripped to a content of 4 grains per 100 cu. ft. The capacity of the plant is 15 million cu. ft. of gas treated daily under a pressure of 160 lb. per sq. in. The cost of treatment, exclusive of depreciation, is appreciably less than I per 1000 cubic feet. Two other plants of much greater capacity have been announced and priorities have been granted, which should bring the total amount of gas treated to 150 million cu. ft. daily. The gas to be treated will have a maximum hydrogen sulphide content of 4500 grains per 100 cu. ft. and will be processed under a pressure of 600 lb. per sq. in. These developments are something entirely new in field practice for the industry. The fact that this heretofore wasted gas is available at very low cost has led to the location of some eight war industries within the state, in addition to the alu-minum plant. Recovery OF Sulphur The Susearch Corporation and the Southern Acid and Sulphur Co. placed in operation during 1941 pilot plants to de-

Jan 1, 1942

By John T. Galey

Production of crude oil for 1940 in southwestern Pennsylvania was off nearly 70,000 bbl., largely as a result of the great number oi abandonments, together with the lack of extension of the Washington and Green County pools. Oil wells completed numbered 51, which is 26 more than last year, but the total initial production of 259 bbl. is only 18 bbl. greater than in 1939. There was an increase of 72 over last year for a total of 209f gas wells. However, 68 7 dry holes were drilled, which is 40 more than a year ago. Thus, 328f wells were drilled during the year, and rigs are erected or drilling is progressing on 59 t more. Shallow Development Oil.—Butler County led in number of oil wells completed, with a total of 27 for an initial production of only 69 bbl. Washington County, with 12 new oil wells, one of which made 40 bbl. from the Fifth sand in S. Franklin township, has 95 bbl., while in Allegheny County 9 wells gave an initial of 86 bbl. for the highest Per well average in the area. This initial was given a considerable boost by one 35-bbl and another 2;-bbl. well in West Deer township, where the Fourth sand produced at 1840 feet. Greene County had only one oil well completed during 1940, and Washington County had 12. The subnormal totals for these counties may be explained by the higher cost of completions and the declining price of crude. The first price change in crude during the year occurred on May 22, when a 25 cut was made. A second 25 cut was made July 12, and was followed by a 156 cut on .Aug. 28. This price held until Nov. 12, when there was a restoration of 156. On Dec. 17 a second 156 increase was put into effect, bringing the price to $I.So per barrel. Gas The large increase in the number of gas wells completed may be attributed to three factors; namely, the recently discovered production possibilities of moderately deep, hitherto little tested horizons, together with increased demand and price. The latter has been made possible by a recent decision of the court, which ruled restraining the public service Commision's prohibition of a raise in the minimum monthly charge to small consumers by one of the major gas companies. A portion of the revenue derived in this manner is being passed along to the producer in the form of higher prices in the field. This higher field rate will remain in effect until a new ruling is made, when it will be reduced in proportion to the reduction of the monthly minimum charge. In an effort to extend the chambers Dam Fifth sand oil pool southwest from Amwell township, Washington County, several wells have been drilled. One of these, in Morris township, washington County, had an initial of 3.2 million cu. ft. open flow from the Big Injun sand. This indicates an entirely new productive area for the latter horizon. Allegheny County had one spectacular well in South Fayette township-—at a depth of about 2500 ft. a 4-million-CU. ft.

Jan 1, 1941

By J. A. Botin, K. H. Singh

INTRODUCTION The Alfredo underground mine is one of the three mining operations of Rio Tinto Minera, S.A., all near the community of Rio Tinto in Huelva province of southwest Spain. The other two operations are Corta Atalaya open pit (Pyrite ore) and Cerro Colorado open pit (Copper ore 1. Underground mining of Alfredo Mine for pyrites started in the nineteenth century and continued without interruption until 1979 when it was discontinued due to economical reasons. In 1972, a new project was started for the mining of copper bearing ores on the footwall of the pyrite deposit. This copper ore is locally named “Cloritas” and it forms a nearly vertical and tabular shaped orebody which forms an envelope at the footwall of the San Dionisio pyrite orebody. Mining of the Cloritas commenced in 1975 using cut and fill stoping. In 1977, the original project was completely revised which led to the introduction of a bulk mining system to achieve a planned production of 3,000 tonnes of ore per day. This paper covers the economic and planning aspects of the mine and discusses the evolution of the mining method for the Cloritas orebody. A GENERAL DESCRIPTION OF THE CLORITAS OREBODY The “Masa San Dionisio” (figure 1 ) is a massive sulphide orebody located in the town of Rio Tinto, about 90 kilometres west of Sevilla, Spain. Extensive vein-type sulphide mineralization exists in the volcanic host rocks of the Masa San Dionisio. Within this area of stockwork veins, there is a higher concentration of copper in the form of chalcopyrite in a zone adjacent to and paralleling the contact with the massive sulphides. This copper envelope is locally referred to as the "Cloritas Orebody” and the ore within it is called "Cloritas”. The main zone of the Cloritas orebody, (figure 11, is tabular and nearly vertical having a length of 375-400 m east-west, a thickness of 20-50 m north-south, and a vertical extension of 500 m from the surface. In addition to this area, there is a second less important low grade area called zone 2A located to the north of the main zone below 26 Level which, in some sections, is not fully separated from the main zone. MINING METHODS Mining in Rio Tinto area can be traced back to the Phoenecians and the Romans. Modern day mining started with the demand for sulphuric acid during the last half of the nineteenth century. By 1971, more than 33 million tonnes of pyrite had been mined out of Alfredo Mine, (San Dionisio Orebody), using labor intensive drift and fill methods and also by open pit method. During the last decade, underground mining of the pyrite had become uneconomic due to lower prices and a slackening demand for pyrite, and the underground mining operations for pyrite were finally stopped in 1979. In 1971, a major change in the long range mining plans for Masa San Dionisio was established. Between 1971 and 1975, underground mining of pyrites was progressively reduced while open pit extraction was increased in

Jan 1, 1981

By Ralph E. Esarey, George V. Cohee

In Indiana, 349 wells were drilled for oil and gas in the year 1942. Of this number, 125 oil wells and 21 gas wells were successfully completed and 203 were dry holes. Drilling activity declined 37 per cent as compared with that of the year 1941. This reduction was brought about largely by Federal Conservation Order M-68, restricting drilling to one well on 40 acres, in order to save steel. This Order was later supplemented to permit closer spacing of wells drilled to sandstone formations in southwestern Indiana. Most of the drilling in 1942 was in the southwestern part of the state. Posey County ranked first, with 94 completions and 44 producers; Gibson County, second, with 77 completions and 38 producing oil wells and 2 gas wells. There were 58 drilling operations in the state at the end of the year. During 1942 a total of 589,734 ft. of hole was drilled, of which 231,702 ft. was wildcat footage. The total initial production of the oil wells completed was 9974 bbl. and of the gas wells, 11,148,000 cu. ft. (Table 2). Of the 349 wells completed, 122 were wildcat wells (Table 3); 26 were completed as oil wells; 17 were extensions to proven fields and 9 discovered new pools. Posey County was foremost in wildcat drilling, with 37 wells completed (Table 6). Thirty-five per cent of the wells drilled in 1942 were wildcat, as compared with 25.5 per cent in 1941. It is anticipated that the percentage of wildcat wells drilled in 1943 will be greater, although the total number ol ,wells drilled in the state will probably be less. The new discoveries in Indiana in I942 were, for the most part, one-well pools in the southwestern part—in Posey, Gibson and Spencer Counties (Table 4). Most of the development in pools took place in the . Hazelton and Kirksville pools in Gibson County, Mr. Vernon pool in Posey County and the Vernon Heights pool in Vander-burgh County. Deeper production was obtained from the Osage limestone in the Hazelton pool at a depth of 2402 ft., 650 ft. below the productive McClosky limestone. The well had an initial production of 140 barrels. Extensions to 17 pools in the southwestern part of the state were successfully completed (Table 5). An interesting development during 1942 was new production from the Devonian limestone in the Dodds Bridge pool, Sullivan County. The Ohio Oil Co. deepened one of its wells, which had been producing from a shallow sand, to the,Devonian, and it was completed for an initial production of 77 bbl. Five other Devonian producing wells were completed in that area. Crude-oil production in Indiana in 1942 was 6,609,000 bbl. (Table I). The Griffin field, Gibson and Posey Counties, which produced approximately 3,550,000 bbl., accounted for more than half of the state's production. The Mt, Vernon and New Harmony fields were next in importance of production, with 684,000 and 523,000 bbl., respectively. The price of crude oil was $1.22 a barrel for the old

Jan 1, 1943

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By George V. Cohee, Ralph E. Esarey

In Indiana, 349 wells were drilled for oil and gas in the year 1942. Of this number, 125 oil wells and 21 gas wells were successfully completed and 203 were dry holes. Drilling activity declined 37 per cent as compared with that of the year 1941. This reduction was brought about largely by Federal Conservation Order M-68, restricting drilling to one well on 40 acres, in order to save steel. This Order was later supplemented to permit closer spacing of wells drilled to sandstone formations in southwestern Indiana. Most of the drilling in 1942 was in the southwestern part of the state. Posey County ranked first, with 94 completions and 44 producers; Gibson County, second, with 77 completions and 38 producing oil wells and 2 gas wells. There were 58 drilling operations in the state at the end of the year. During 1942 a total of 589,734 ft. of hole was drilled, of which 231,702 ft. was wildcat footage. The total initial production of the oil wells completed was 9974 bbl. and of the gas wells, 11,148,000 cu. ft. (Table 2). Of the 349 wells completed, 122 were wildcat wells (Table 3); 26 were completed as oil wells; 17 were extensions to proven fields and 9 discovered new pools. Posey County was foremost in wildcat drilling, with 37 wells completed (Table 6). Thirty-five per cent of the wells drilled in 1942 were wildcat, as compared with 25.5 per cent in 1941. It is anticipated that the percentage of wildcat wells drilled in 1943 will be greater, although the total number ol ,wells drilled in the state will probably be less. The new discoveries in Indiana in I942 were, for the most part, one-well pools in the southwestern part—in Posey, Gibson and Spencer Counties (Table 4). Most of the development in pools took place in the . Hazelton and Kirksville pools in Gibson County, Mr. Vernon pool in Posey County and the Vernon Heights pool in Vander-burgh County. Deeper production was obtained from the Osage limestone in the Hazelton pool at a depth of 2402 ft., 650 ft. below the productive McClosky limestone. The well had an initial production of 140 barrels. Extensions to 17 pools in the southwestern part of the state were successfully completed (Table 5). An interesting development during 1942 was new production from the Devonian limestone in the Dodds Bridge pool, Sullivan County. The Ohio Oil Co. deepened one of its wells, which had been producing from a shallow sand, to the,Devonian, and it was completed for an initial production of 77 bbl. Five other Devonian producing wells were completed in that area. Crude-oil production in Indiana in 1942 was 6,609,000 bbl. (Table I). The Griffin field, Gibson and Posey Counties, which produced approximately 3,550,000 bbl., accounted for more than half of the state's production. The Mt, Vernon and New Harmony fields were next in importance of production, with 684,000 and 523,000 bbl., respectively. The price of crude oil was $1.22 a barrel for the old

Jan 1, 1943

By E. J. Whittenberger

OVER the past two decades, the Cr-Ni stainless steels, popularly termed 18-8 steels, have been used in ever increasing amounts in the aircraft, automotive, chemical, transportation, and building industries.' The contribution of nickel to these steels is associated with its strong austenite forming tendencies which assure good hot and cold forming characteristics, and with its beneficial influence upon corrosion resistance, especially in oxidizing acids. The adjustment of the chromium and nickel contents has been used advantageously in controlling the rollability and the response of the mechanical properties of these steels to cold reduction. With the advent of the jet age and the government stockpiling of nickel, considerable emphasis has been placed upon the development of satisfactory low nickel or nickel-free substitute austenitic stainless steels, especially for nonmilitary applications.2 Fer-ritic 17 pct Cr (AISI Type 430) stainless steel has been effectively substituted for the austenitic grades in applications with mildly corrosive exposure. However, the limited formability and ferromagnetic behavior of this grade do not permit its satisfactory use for many applications. To achieve better formability in a nenmagnetic steel and conserve nickel, a number of low nickel substitute austenitic grades of stainless steel have been developed in recent years. In most of these steels, manganese and nitrogen have been substituted for a portion of the nickel content, for example, 17 pct Cr-4 pct Ni-6 pct Mn (AISI Type 201), 18 pct Cr-5 pct Ni-8 pct Mn (AISI Type 202), and 16 pct Cr-1 pct Ni-17 pct Mn, all of which contain approximately 0.15 pct N.1 The precipitation of ferrite when large ingots of these Cr-Ni-Mn-N steels are heated to temperatures high enough for conversion to slabs on conventional universal slabbing mills has seriously affected the hot workability of these steels. This has been especially true in the case of the 16 pct Cr-1 pct Ni-17 pct Mn (sometimes referred to as 15 pct Cr-1 pct Ni-15 pct Mn) composition." Because it is possible that little, if any, nickel will be available for nonmilitary stainless steel applications in the event of a national emergency, a need has existed for a nickel-free austenitic stainless steel containing hot and cold forming characteristics similar to 18-8 steels and corrosion resistance at least comparable to the 17 pct Cr ferritic steel. The aforementioned deleterious effect of ferrite upon the hot working characteristics of the 16 pct Cr-1 pct Ni-17 pct Mn, steel indicates the importance of establishing the austenite-austenite plus ferrite phase boundaries as the first step in the development of nickel-free or low nickel substitute steels. This paper presents the data collected in an elevated temperature constitutional study of the Cr-Ni-Mn-N system at the South Works of the United States Steel Corp. Experimental Procedure The 300 compositions used in the investigation were melted in a 26 Ib induction furnace and cast in 3 14 in. diam by 18 in tall hot-tcpped ingot mo1ds.

Jan 1, 1958

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By H. E. Montgomery

Engineering trends for some years have been toward higher temperatures, both in process work and in steam generation. Progress in design has been dependent upon the development and evaluation of suitable alloys. Elementary knowledge of the limitations of copper-base alloys indicate their unsuitability for the higher ranges of operating temperatures; say, for steam to 950°F. Emphasis upon the more severe conditions perhaps is a reason why more complete evaluations have not been made for copper-base alloys over their range of suitability. However, the few studies made show clearly the need for more accurate evaluations. Some copper-base alloys long looked upon favorably because of superior room-temperature properties are not as desirable as some others perhaps not so "strong" and "hard," as measured by usual acceptance tests. Load-carrying capacity and structural stability arc two important factors. Structural stability as influenced by temperature, by presence of corrosive media, or by the effects of stress itself, frequently is a limiting factor. An early reference to creep properties of the cast copper-base alloys is that of Brown1 (Admiralty gun metal, Cu 87.5, Sn 10.1, Zn 2.3 and Pb 0.08). His tests were similar to present-day stress-rupture tests without measurement of creep elongrttion. Loading was in steps with usually 24 hr. between steps, and continued until failure. He advocated a "useful strength value" of 61/2 tons (I4,560 Ib.) per sq. in. at 572°F. (300°C.). A specimen broken in 1/2 hr. at 572°F. had a strength of 21 tons (26,880 Ib.) per sq. in. The strength values as determined by 1/2-hr. tests and those by the longer stress-rupturc start to differentiate at 392°F. (200°C). This is the temperature at which time at load began to play an important part. Bolton, Price and Hebemann2 give creep curves on 88-10-2 (A.S.T.M. B-60, CU 88, Sn 10, Zn 2) and steam or valve bronze (A.S.T.M. B-6I, Cu 87.50, Sn 6.00, Zn 3.75, Pb 1.70) at 500°F. Direct comparison of the two alloys under 7500 lb. per sq. in. stress showed the steam bronze (A.S.T.M. B-61) superior in creep strength to the 88-10-2 (A.S.T.M. B-60). The steam bronze shows no creep after 700 hr. (1540-hr. test). The 88-10-2 shows a rate of about 7.0 per cent in 100,000 hr. over the last 700 hr. of the test. Creep curves on the steam bronze are also given at the same temperature (500°F.) with loads of 6500 lb. per sq. in. and 8000 lb. per sq. in. These indicate "creep strengths" (creep rate within I per cent in 100,000 hr.) in excess of 8000 lb. per sq, in. for this alloy. It was found that higher percentages of tin are detrimental to creep resistance. This is caused by the presence of or formation during test of considerable alpha-delta eutectoid in the higher tin alloys. Bolton also states that the high

Jan 1, 1945

By Robert S. Dewey

Drilling in West Texas during 1942 was substantially less than in the previous year. In all. 1267 Wells were drilled, as compared with 2325 wells in 1941. Of these 1267 wells, 1052 oil wells, 10 gas wells and 69 dry holes were drilled in proven fields and 36 oil wells, one gas well and 99 dry holes were wildcat operations. Of the 36 wildcat wells completed as oil producers, 16 led to new field discoveries, three found new productive horizons in old fields, and 17 extended the productive limits of established fields. Where semiwildcat drilling took place along established productive trends, there was often no sharp demarcation between wildcat wells that extend field limits and normal development to fulfil lease obligations, other than the arbitrary classification of a well as a wildcat if it was drilled at a distance of 2 miles from a producing oil well. The dry hole drilled on the edge of a field may have proved a more hazardous operation than a semiwildcat drilled several miles from production but favorably located on structure. The percentage of successful wildcatting ranges from 26.5 down to 14 per cent, dependent upon the degree of inclusion of the semiwildcat operations. Irrespective of which figure was used, the West Texas area maintained its better than average exploratory position. No doubt a number of factors may have influenced the extent of the 1942 development. Among those arising from the economic dislocation attendant on the war effort, the following are worthy of note. Owing to inductions into the armed forces and shipyard competition for mechanically trained men, experienced drilling personnel was sharply reduced, thereby increasing drilling costs and well-completion hazards. Replacement labor has not met the same standard of responsibility or workmanship to which the oil industry has grown accustomed. Increased military consumption of aviation gasoline and other crude products, coupled with decreased domestic consumption of lower-octane gasoline, has stimulated the market demand for the types of sweet crude most readily processed with available refinery equipment to meet war requirements, and has depressed the market demand for the sour West Texas crudes. As a majority of the purchasers of West Texas crude normally ship a substantial portion of sour crude to the refineries on the Atlantic seaboard, the loss and diversion of tanker service between Gulf Coast and north Atlantic ports have further curtailed the market demand for this type of crude oil. As some purchasers of crude oil were able to move by pipe line their West Texas trunk-line capacity to Midwestern refining centers, they were not impelled to curtail purchases of West Texas crude. The varying ability of the purchasers of crude oil to market West Texas crude was reflected back to various fields to which they were connected, causing an unequal distribution of production as among fields and operators. The pipe-line runs from the West Texas-New Mexico area decreased from approximately 354,000 bbl. Per day in January to about 265,000 bbl. in December 1942. .Approximately 2,991,000 bbl. of West

Jan 1, 1943

By Robert S. Dewey

Drilling in West Texas during 1942 was substantially less than in the previous year. In all. 1267 Wells were drilled, as compared with 2325 wells in 1941. Of these 1267 wells, 1052 oil wells, 10 gas wells and 69 dry holes were drilled in proven fields and 36 oil wells, one gas well and 99 dry holes were wildcat operations. Of the 36 wildcat wells completed as oil producers, 16 led to new field discoveries, three found new productive horizons in old fields, and 17 extended the productive limits of established fields. Where semiwildcat drilling took place along established productive trends, there was often no sharp demarcation between wildcat wells that extend field limits and normal development to fulfil lease obligations, other than the arbitrary classification of a well as a wildcat if it was drilled at a distance of 2 miles from a producing oil well. The dry hole drilled on the edge of a field may have proved a more hazardous operation than a semiwildcat drilled several miles from production but favorably located on structure. The percentage of successful wildcatting ranges from 26.5 down to 14 per cent, dependent upon the degree of inclusion of the semiwildcat operations. Irrespective of which figure was used, the West Texas area maintained its better than average exploratory position. No doubt a number of factors may have influenced the extent of the 1942 development. Among those arising from the economic dislocation attendant on the war effort, the following are worthy of note. Owing to inductions into the armed forces and shipyard competition for mechanically trained men, experienced drilling personnel was sharply reduced, thereby increasing drilling costs and well-completion hazards. Replacement labor has not met the same standard of responsibility or workmanship to which the oil industry has grown accustomed. Increased military consumption of aviation gasoline and other crude products, coupled with decreased domestic consumption of lower-octane gasoline, has stimulated the market demand for the types of sweet crude most readily processed with available refinery equipment to meet war requirements, and has depressed the market demand for the sour West Texas crudes. As a majority of the purchasers of West Texas crude normally ship a substantial portion of sour crude to the refineries on the Atlantic seaboard, the loss and diversion of tanker service between Gulf Coast and north Atlantic ports have further curtailed the market demand for this type of crude oil. As some purchasers of crude oil were able to move by pipe line their West Texas trunk-line capacity to Midwestern refining centers, they were not impelled to curtail purchases of West Texas crude. The varying ability of the purchasers of crude oil to market West Texas crude was reflected back to various fields to which they were connected, causing an unequal distribution of production as among fields and operators. The pipe-line runs from the West Texas-New Mexico area decreased from approximately 354,000 bbl. Per day in January to about 265,000 bbl. in December 1942. .Approximately 2,991,000 bbl. of West

Jan 1, 1943

By Robert S. Dewey

More wells were drilled in West Texas† during 1944 than in any year since 1941. As compared with 1943, there was an 82.5 per cent increase in the total number of completed wells. The 1646 wells required an estimated 140,715 days to complete for a total of 7,632,249 ft. An average of 85 completion days was required to drill to an average of 4630 ft. This depth is approximately 100 ft. greater than that of the previous year. It is estimated that $100,000,000 was invested in drilled wells. As of Dec. 31, 1944, there were 270 field and 91 wildcat wells being drilled. While an identical number of wells were drilling Dec. 31, 1943, the proportion of wildcats increased in 1944 from 19.7 to 25.2 per cent. During 1944, oil wells were completed in 103 of the 164 fields in West Texas. Of the 1361 oil wells, 385 were in Slaughter, 116 in Fullerton, 63 in North Cowden, 62 in Fuhrman-Mascho, 59 in Wasson, 52 in Westbrook and 47 in North Ward. Approximately 22 per cent of the wildcat drilling was to pre-Permian formations. Despite the increasing proportion of wildcat wells drilled, the wildcat discovery rate has declined since the year 1942. AS compared with 1943, the number of wildcat wells drilled increased from 11.7 to 12.7 per cent and the footage in wildcat exploration increased from 13.3 to 13.8 per cent of the total. The monthly production of crude continued to increase to a peak of 15,336,000 bbl. in October 1944. As compared with a similar peak production in October 1943, there was a 37.3 per cent increase. The yearly production increased from 98,165,-ooo bbl. in 1943 to 159,943,000 bbl. in 1944, an increase of 62.8 per cent. Based upon an assumed average price of $1.00 per barrel and less 1/8 royalty, the gross return to the producer amounts to $140, 000,000. From 1943 to 1944, the average number of producing wells increased 6 per cent while the average daily production per well increased 53.1 per cent. The average daily production per well increased from 17.5 bbl. in 1943 to 26.8 bbl. in 1944. The proportion of flowing wells decreased from 50.5 per cent in January to 49.1 per cent in December 1944. Drilling With the continued shortage of labor and materials, drilling costs have risen sharply. Just how much is difficult to ascertain. Owing to competition for available drilling rigs, contractors are reluctant to assume drilling risks. In consequence, some contracts are let on a cost plus basis, or day work below some specified depth with the operator furnishing part of the consumable materials, such as mud and drilling bits. Contractors are having difficulty in maintaining full and effective drilling crews with insufficient and inexperienced labor. Service companies have inadequate labor and equipment to meet their appointments promptly. Pipe Lines The Gulf Pipe Line Co. increased the capacity of its 10-in. main line by filling in gaps amounting to 75 miles on the loops between Judkins and Weatherford, Texas.

Jan 1, 1945

By R. G. Hudson, H. W. Paxton

The activities of iron and chromium in their binary system have been measured by the Knudsen orifice technique. The system is close to ideal at 1200- 1250 C with slight positive deviations. The effect of this on the liquidus and solidus is discussed and these are calculated for two limiting assumptions. The vapor pressure of pure iron, pure chromium, and one alloy is compared with that obtained by the Langmuir free-evaporation technique. The results agree, indicating a vaporization coefficient close to 1. HERE are no reported data on the thermody-A namic activity of iron and chromium in the solid portions of the phase diagram. It is generally assumed'.' that the liquid solutions of iron and chromium obey Raoult's law. Chen and Chipman" have inferred that the liquid solution obeys Raoult's law. The minimum' in the solidus-liquidus curves for the iron-chromium system shows that there are deviations from ideality in either the solid or liquid or both. Because of the importance of developing reliable techniques for obtaining activity data in alloy systems at high temperatures and of the data so obtained, an investigation of the activity of iron and chromium in the binary at 1200-1250 C was undertaken using the Knudsen cell. Experimental The apparatus and experimental procedures used in this investigation were described in a previous paper." The various materials used for the construction of the Knudsen cell are listed in Table I. The metal used for the determination of the vapor pressure of chromium was 99.9 pet pure, obtained from A. D. Mackay, Inc. The iron was obtained as electrolytic grade from Fisher Scientific Company. The Fe-Cr alloys used are shown in Table 11. The largest error and controlling factor in the accuracy in the experiments reported here are introduced because of temperature uncertainty, which is estimated to be ±3 deg C. This introduces an uncertainty of 26 pet in the measured pressure. Experimental Results and Calculations The vapor pressures of pure iron and pure chromium were calculated from the measurements by the Knudsen equation3 on the assumption that only Cr or Fe atoms were present in the gas phase. For metal vapors, at the high temperatures and low pressures involved in these measurements this should be a reasonable assumption. Whitman" corrections for the cells were made. The data and results of pressure calculations are presented in Table I, and are plotted in Fig. 1. In addition the heat of vaporization at the absolute zero, ?E°°, has been calculated for chromium. These calculations are summarized in Table 111. The data used in these calculations are as follows kelley13 (F° - E°°/T ) Speiser, et al H (F° - E°°/T ) 010 where F" — standard free energy at temperature T It was necessary to calculate the total pressure above the alloys from the total weight loss W of the cell during a run, because of the fact that all attempts to collect and analyze the chromium and iron vapor effusing from the cell in the apparatus available failed. The failure resulted from the re-

Jan 1, 1959

By Robert J. Linney

IN the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the " 21 " Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. 1, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously developed sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel to footwall and hanging wall to make a bench, spalling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig. 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore; by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1945