Search Documents

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915, when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps. Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible. Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blast-hole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Sucti shots were fired from either end by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1953

By R. O. Williams

Analytical representation of the thermodynamics of solutions is highly desirable from the standpoint of accuracy, compactness, and numerical manipulations. In particular, computer calculations are greatly implemented. Mathematical considerations show that previous expressions have one or more serious defects. This investigation shows a Fourier series to be satisfactory but that it is also possible to derive a new series which fits certain additional conditions. Included examples show the value of analytical expressions in giving a simple characterization of each system using some two to five parameters, the elimination of the Gibbs-Duhem integration, and the es timation of the error for the experimental function as well as derived functions. It is further shown that the present characterization provides easy comparison between systems. IN the past, thermodynamic calculations have depended to a considerable extent on tabular and graphical methods. As the volume and precision of such data increase such methods become less satisfactory. Specifically, the selection of the optimum representation and the estimation of errors require statistical methods which in turn require analytical representation. The utilization of such data require further manipulations which are best done analytically for maximum precision. For example, phase equilibria are determined by common tangents to free-energy curves: a graphical determination is normally of low accuracy. As computers are increasingly used analytical representations become almost mandatory. Insufficient mathematical consideration has been given previously to the selection of empirical expressions. Those expressions having some theoretical justification are generally too inflexible and mathematically unattractive. We consider the problem in some detail and show that a Fourier series can be effectively used. Also a new series is defined which has certain advantages. ANALYSIS We wish to consider the analytical representation of the heat of mixing, AH, the excess free energy, ?Gxs, and the excess entropy, ?sXS, as a function of composition, X, for binary solutions relative to the pure components in the same state. When a distinction is not required, we use W to denote any one of the above functions. One may use a Taylor expansion around X = 0 to generate a power series. As the derivatives are un- known we represent the series as W = A + BX + CX2 + DX3 + EX4 + ... [l] where the constants A , B, C , ..- are to be selected to provide some optimum fit. For the extremes of composition W is necessarily zero so it follows that A = 0 [2a] B +C + D + E +••• = 0 [2b] Nonelectrolytes, which we are considering, appear to satisfy the condition that d3W/dx3 = 0 [3] in the terminal regions. This is the basis of the a, ß, and Q functions used by Hultgren et al.' and others. While this condition does not have a strong theoretical basis it does appear desirable that any analytical relation should satisfy this condition. Darken2 and Turk-dogan and Darken3 have shown that many systems exhibit this behavior over an extended range from each terminal region, departure being restricted to a limited intermediate region. Since we have no a priori knowledge as to where this transition occurs we can require that this condition be satisfied only as a limit at the extreme compositions as a general condition. We will show later how more restricted conditions can be included in specific solutions. Darken2 has called this behavior the quadratic formalism; we call our application the limiting quadratic formalism, LQF. This condition applied to the above power series requires that D = 0 [4a] 4-3-2E +5-4-3_F + 6 • 5 . 4G + ••• =0 [4b] The form of the power series normally used, due to Margules,4 is W=X(1-X)(A + BX + CX2 + DX3 + EX4 + •••) [5] where A, B, C, --. are a new set of constants. (Guggenheim5 has given a variation of this expression in a more desirable form. Since, however, it is contained in the above expression it does not require separate consideration.) This form is precisely what results by incorporating the conditions in Eq. [2] into the power series and regrouping the constants. The LQF requires that B =C [6a] and 4.3.2(D-C) +5-4-3(E-D) + ••• =0 [6b] Thus, the correct form of the Margules expression with two adjustable parameters is w =X(1-X)[A + B +X2-2/3x3)] 171 and the EX4 term must be included before three adjustable parameters are permitted.

Jan 1, 1970

By E. F. Thomas

THE late George S. Rice was active in the inves--I- tigation of bumps, particularly in the last ten years of his career as chief mining engineer of the U. S. Bureau of Mines. Since most of his investigation was carried out in Great Britain, continental Europe, and—to a lesser extent—Canada, his thinking on prevention was influenced considerably by the experience of those countries. It is not surprising, therefore, that when he was called upon a few years before his retirement to investigate bumps in the U. S. and suggest ways to prevent them, he turned to longwall mining. A longwall method had been most successful in combating the bump hazard in mining coal under deep cover, especially in Great Britain, but the prevailing method there at the time was advancing longwall mining, which he knew was uneconomical under U. S. mining conditions. For this reason he proposed a modified retreating longwall system that he believed included the best features of the advancing method. As brought out by Rice,' if the cover is 2000 ft and 50 pct of the coal is extracted, the static load on the remaining pillars will be about 4000 psi, which exceeds the ultimate crushing strength in most instances. If the pillar coal is overloaded before a pillar line is established, then the abutment zone preceding a line of extraction is no place to split pillars or extract them by any method other than an open-end system. Rice therefore advocated open-end mining, preferably by longwall, but he was willing to compromise with long-face mining if the longwall method was not acceptable. Rice's system was put into operation in a mine in Harlan County, Kentucky,3 but subsequent experience has shown that it did not take into account two important factors—avoidance of pillar-line points and maintenance of adequate development in advance of the pillar-line abutment area. For ten years after Rice's retirement the USBM did little investigation and research on bumps, chiefly because so few were occurring that there was not much cause for alarm. But in 1951 there were three occurrences involving fatal injuries, and the Bureau began a statistical survey in that year. C. T. Holland, head of the department of mines at Virginia Polytechnic Institute, was retained as a consultant. The resulting study' of 117 case histories brought out these important conclusions: 1) Almost invariably the bump occurred in a locality affected by the abutment zones of one or more pillar lines. 2) In most cases the locality of the bump was influenced by the abutment zones of more than one pillar line. The term pillar-line point has been used for many years in the Appalachian region for such a situation. Point is used in the geographical rather than the mathematical sense. 3) In pillar-line extraction the following practices are safest in preventing bumps: a. The mine layout should provide for pillars of uniform size and shape along the extraction line. b. The mine layout should be planned so that no development need be done in the abutment zone of a pillar line. c. The layout should permit open-end extraction of pillar lines from the next goaf, so that it will not be necessary to resort to pocket mining, splitting pillars, or any practice that will involve driving in the direction of the goaf within the abutment zone. d. Pillars should be large enough to support area without undue roof and floor convergence before establishment of a pillar line. These are, of course, generalities, and while they are useful in laying out areas where bumps can be expected, they are of limited help in many mines that were committed to a system of mining before it was realized that they were subject to bumps. Under such conditions it becomes necessary to choose between the following alternatives: 1) Abandon the territory, except for pillars that offer no extraction problems. 2) Through experience select the pillars that are most heavily loaded, and, by augering, induce bumps from a safe vantage point so that impinged loads are relieved. This method was first developed at the Gary, W. Va. mines of U. S. Steel Corp. and later adapted to mining thick coal beds at Kaiser Steel's Sunnyside mine in Utah. No scientific method is available to determine where to drill within a loaded pillar. Although this method of unloading has worked very successfully at Gary—with one exception—

Jan 1, 1959

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915; when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps: Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible: Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn-drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blasthole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated' by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Such shots were fired from either end .by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1952

By T. A. Wilson, S. L. Hoyt

THE plastic deformation of slender single crystals of zinc has been described in some detail in the paper by Mark, Polanyi and Schmid,1 which has become a classic, and also by one of the present authors in a somewhat shorter account.' The study of single-crystal zinc is termed classical because zinc single crystals offer, perhaps, the best material yet available for the study of atomic behavior during deformation and the effect known as "strengthening" in metals. A considerable amount of additional work has also been done on single-crystal zinc, but as it is not closely related to the present paper it will not be considered. Throughout all the former work, the mechanism of plastic deformation first described by Mark, Polanyi and Schmid has been assumed to hold. This may be said to offer the strongest confirmation of its correctness. Even so, the picture of the process has never been as completely portrayed as is desirable. The first object of the present paper is to describe work that has been done in this field, and which is even yet being carried on, in the hope that a more complete picture may be obtained. Mathewson and Phillips' have recently described a new mechanism of the deformation of zinc based on their study of large rectangular crystals. One of their conclusions was that deformation produced twinning with a rotation of some of the basal planes into positions 94° removed from their original position; a position almost the same as that of the prismatic planes before twinning. A second conclusion was that fracture occurred along these basal planes in their new position, and, therefore that fractures previously regarded as prismatic were in reality basal. Such findings are of great significance and they raise a question as to the generality of such behavior. Professor Mathewson's opinion is that even the slender cylindrical single crystals behave in the same manner as his large rectangular crystals when strained by simple tension.

Jan 1, 1928

By Harold Earle Cook

The purpose of this paper is to state briefly the inspection requirements of the Bureau of Ordnance, the specifications governing the inspection, and the physical and chemical properties of the steel used in the construction of ordnance for our Navy. It would be of interest to evoke discussion on points in these specifications which do not tend to insure the production of the very best material for the purpose intended. In other words, what requirements of our specifications are useless and also in what manner are our specifications deficient? It might be well at the start to answer the first criticism of this paper which will probably be made, and that is that the title does not agree with the subject matter. Considering metallographic work as covering only the macroscopic and microscopic examination of metals, this paper will have gone beyond the subject; but it is believed that a broader definition of metallography is that it is the study of the relation of the internal structure of metals and alloys to their composition and to their physical and other properties. The internal structure of steel is dependent on its physical and its chemical properties. These physical properties are dependent on the chemical composition and the mechanical and thermal treatment of the steel. So it seems that this subtitle would not be entirely necessary and that the title " Metallography of Steel for Ordnance Purposes" would cover a study, not only of what we can learn of macroscopic and microscopic examination, but broadly of the whole subject of the specifications, the fulfillment of the requirements of which produce the structural conditions revealed by macroscopic and microscopic examination. I will refer but briefly at the beginning to the microscope and its uses in our inspection. It is only very recently that the Bureau of Ordnancc has furnished certain of its inspection offices with a portable Tassin outfit for the microscopic examination of steel. Since that

Jan 1, 1916

By GERALD A. WARING

ALASKA'S coal consumption is now about 130,000 tons annually. About one-quarter of this amount is used in the southeastern part of the territory and in settlements on the western coast and comes from Seattle and from British Columbia mines. About 60,000 tons is sub-bituminous coal from the Healy River mine in central Alaska, and is used mainly at Fairbanks, sixty miles to the north, for heating and the development of electric energy, for the city and the gold-dredging operations of the Fairbanks Exploration Co. The remaining 40,000 or 50,000 tons is bituminous coal from Matanuska Valley, in the south-central part of the territory. These coal deposits extend intermittently for about forty miles along the valley, which trends eastward from the upper end of Cook Inlet.

Jan 1, 1934

By JULIAN HINDS

Industrialization is raising the standard of living of people everywhere. The common man is demanding and getting more of everything. Perhaps more markedly than most other things, he is consuming more water. A hundred years ago water for domestic use, in all but a few large centers, was lugged from wells in buckets. This still is true in many rural areas, even in the enlightened United States of America. but pumps and pressure systems are rapidly replacing the "old oaken bucket," even on farms and in isolated country homes. Nevertheless, many still fail to see water as a ?commodity? in the same sense that coal, lumber, fertilizer, and bread are considered as commosities. Water is too frequently taken for granted.

Jan 1, 1949

By D. E. Light, J. Y. Somnay

The use of alkyl acid phosphates and their alkali salts as collectors for the uranium minerals brannerite and uranothorite was investigated. In particular a detailed flotation study was carried out using isooctyl acid phosphate as a promoter. Tests were conducted on an Elliot Lake ore analyzing 0.11% U 3 O 8, chiefly as brannerite, and approximately 9% pyrite. Pyrite was floated with conventional reagents; the flotation of brannerite from the sulfide tails was studied to determine the optimum pH and pulp density to employ with isooctyl phosphate. 4 uranium recovery of over 90% was possible with a selectivity index of 8.95 when these tails were floated at 17% solids and a pH of 1.7. The effect of various modifying agents was also investigated. Aluminum sulfate, lactic acid and sodium silicate improved the selectivity of collection yielding selectivity indices of 9.5 to 11.5. Ferric chloride was found to be a depressant for brannerite. A Bancroft ore which analyzed 0.13% U308, and contained uranothorite was also amenable to flotation using isooctyl acid phosphate. The composite uranium concentrate obtained assayed 0.41% U308 at a recovery of 95.3% and a ratio of concentration of 3.24. Previous investigations1,2 on the flotation of brannerite, pitchblende, uraninite and/or uranothorite from various Canadian ores showed that fatty acids, including oleic acid and tall oils, petroleum sulfo-nates and alkyl acid phosphates, were suitable collectors for these uranium minerals. Additional work carried out by the Mines Branch in Ottawa on brannerite ores from the Elliot Lake area3 used the tall oil Acintol FA-1, or FA-2, as a collector. A recovery of 92% of the uranium in a concentrate which contained about 55% of the weight and assayed 0.2% U3O8 was obtained from a feed of 0.1% U308 in this latter instance. Eigeles et a1.4 carried out flotation on pitchblende ores and found that the most promising results were obtained with alkyl acid phosphates and their alkali salts as collectors. Within the homologous series of alkyl phosphates, the best flotation characteristics were displayed by isooctyl phosphates. Further, isooctyl phosphate derivatives were much less sensitive to hardness forming salts than oleic acid, enabling all flotation tests to be made with tap water. This paper describes tests employing alkyl acid phosphates for the flotation of ores containing brannerite and uranothorite. The flotation work described herein was conducted in conjunction with the development of a leaching process for Elliot Lake, Ontario, brannerite ores. In this process pyrite in the ore was concentrated by flotation and roasted, providing sulfur dioxide which was used to produce sulfuric acid in situ in a liquid-solid extraction process. A 40% conversion to sulfuric acid was indicated at a leaching temperature of 80°C; this resulted in the extraction of 93% of the total uranium after a contact period of 6 hr. A rotary kiln was used as a leaching vessel. Preconcentration by flotation was studied in conjunction with the above process to reduce the bulk of solids for leaching and, consequently, capital expenditure. The materials and methods used in this study will be described initially. Then the results will be presented in two sections, the first dealing with the brannerite ore, and the second with the uranothorite. Finally an economic analysis of the results on the brannerite material will be made. MATERIALS AND METHODS The two ore samples examined were from uranium-producing mines. One was a brannerite ore, a uraniferous quartz pebble conglomerate from the Elliot Lake area, which contained 0.11% U3O8, 4.3% S and 4.5% total Fe. Mineralogical studies of similar samples indicated the presence of quartz, microcline, sericite, pyrite and minor quantities of rutile, pyrrho-tite and zircon. The other ore was from a biotite-rich pegmatite in the Bancroft area; feldspar, quartz and biotite formed the major gangue components. Uranothorite was the principal uranium mineral; the head assay was 0.13% U 3 O 8. Preparation of Feed: The ores were crushed to —10

Jan 1, 1963

By G. J. Dickman, W. N. Thomas

The factors involved in selecting, a drive system for a grinding mill, including gearing arrangement, motor selection, and electric-supply system limitations are reviewed. Equipment costs are evaluated on a dollar per horsepower basis and starting performance is analyzed, the latter making use of a recently developed computer program. The present interest in large-diameter grinding mills and the rapidly rising cost of the drive in proportion to the cost of the mill establishes a need to explore the drive system in detail. The drive for a 7 to 8,000 hp mill will cost from $350 to $600,000 which represents nearly half the total cost of the mill package, and requires as much building space as the mill proper. Some of the drive components require a longer time to manufacture and the installation time and costs are equal to those for the mill. It is apparent that the drive has become a dominant factor in the overall mill design consideration. A new plant requires a tremendous investment in both time and money. With the high degree of competition in the mining industry, low capital cost is an exceedingly important factor in the development of a project. It is just as important, however, to insure that the equipment is going to perform satisfactorily for the anticipated life of the project without adding unplanned operating, maintenance, and replacement costs. This is the position in which the engineer or designer usually finds himself and is really one of his primary functionsestablishing a realistic compromise between cost and performance. Large primary grinding mills can represent a major portion of the cost of a plant and the drive system accounts for a substantial part of this cost. These facts justify a careful analysis of the drive requirements and all of the factors involved in ultimately arriving at the best system for the lowest cost. A number of excellent papers have been published on various aspects of mill drives. The authors have used information from these papers in making a study of a drive for a 7600-hp, 32 x 12-ft autogenous mill. This was a broad investigation, including mechanical and electrical design, layout, performance, and maintenance considerations, and overall economics leading to the selection of the optimum system for that mill. This paper was developed from the study and includes information applicable to large mills in general. For a successful and economical application, the drive must be considered as a system and all of the components analyzed to determine their effect on the system. This requires the participation of the mill designer, gear, and other mechanical component manufacturers, motor manufacturer, plant designer, and operator. A careful analysis of the mill torque requirements is first necessary to provide a basis for selection of the mechanical and electrical drive components. Because of manufacturing limitations on the size and capacity of gearing available for these low-speed applications, an evaluation of costs for various gear ratios and configurations in conjunction with motor speeds is required. Consultation with the power-supply company is necessary to determine limitations on motor-starting disturbances and to analyze operating costs on the basis of existing rate structures and low characteristics. Finally, consideration must be given to the drive arrangement and its affect on plant layout, space requirements, and location of auxiliary equipment for the selected process. There are presently three basic schemes for driving a mill. The first is a direct drive by a motor operating at mill speed with no gearing. The second is by a higher-speed motor through a trunnion-connected gear drive. The third is by a motor through the more conventional pinion and ring-gear with the option of an interposing gear box to permit greater motor speed than pinion shaft speed. [(Fig. 1.)] Several manufacturers have or are presently developing motors which drive the mill directly without the use of gears. One arrangement has the motor armature intimately surrounding the mill shell-discharge spout or extension of the trunnion journal. The motor stator is then supported independently and surrounds the shell or trunnion-mounted rotor. Another variation utilizes an independent mill-speed motor connected to the trunnion by a drive shaft and flexible couplings.

Jan 1, 1972

By G. D. Just

INTRODUCTION Large scale underground mining involves the bulk handling of fragmented material. The cost and efficiency of the mining systems is there- fore significantly influenced by material flow characteristics. Flow problems may occur in the form of ore pass blockages which interrupt the free flow at extraction openings. The costs of such delays can be readily assessed and compared to the costs incurred in reducing blockages by improved fragmentation or larger ore passes. In practice the problem is more complex than this statement suggests because it is generally un- economic to design for zero ore blockages. Another major flow problem occurs in the form of relative movement of ore and waste as the fragmented material is extracted. This produces waste dilution in the recovered ore and influences total ore recovery. This flow problem is much more complex than the ore block- age phenomena. Many questions concerning the precise flow characteristics remain unanswered because of the variability of size distributions, particle shapes, material properties and the total extraction layout and design. Model studies can provide a visual and quantitative illustration of probable flow characteristics but full scale data collection is necessary to evaluate the precision of such information. The methods and types of data obtained must be carefully selected to recover the maximum volume of useful information for operational control and future design. It is essential that honest precision levels are assigned to the data and any subsequent analyses. Grade control data may give misleading short term information on flow characteristics because of the difficulty in knowing the true grade of the mass of material before extraction commences. However, in the long term control of extraction grades is vital to the profitable operation of the mining system. The most efficient extraction design and operational schedule can only be determined after all of the facts and variables are known. This is usually only possible after the orebody has been completely extracted. However, if design and operational personnel have a full appreciation of the nature and variability of material flow under different conditions the best possible results should be achieved. The most significant features of material flow are out- lined in this paper in order to provide mine planning and mine management personnel with some of the necessary information relating to material flow. Available facts and reliable figures from selected publications are noted in association with unbiased and hopefully accurate opinions of the relevance of the data to mine design and mine system control. Possible future developments and profitable areas for research into material flow problems are also detailed. MATERIAL FLOW AND MINING METHODS The effects of material flow on the design and operation of an integrated underground ore handling system is one factor which is common to most mining methods. Analysis of the system as detailed by Just, 1980, permits the identification of unit process objectives. For example, a typical underground ore handling system as illustrated in Figure 1, involves the following unit operations:- (i) Gravity flow of ore in stope (ii) Ore extraction at base of stope (iii) Ore haulage on the production level (iv) Dumping of ore into ore pass system (v) Gravity flow of ore in the ore pass (vi) Underground crushing of ore (vii) Haulage of crushed ore to shaft (viii) Hoisting of ore to the surface. Average flow rates in each of these unit operations can be misleading due to variability in incremental capacity caused by flow blockages and machine delays. Thus to effectively analyse the probable performance of the system, it is necessary to have a measure of the flow loading and haulage rate variability. Mechanical equipment performance specifications can be used to provide such information for loading, haulage and crushing; however, in the case of the gravity flow of material field measurements are required to relate the probability of "hang-ups" to the degree of fragmentation. Factors affecting the frequency of flow stoppages are, size, distribution and cohesiveness of broken material and the geometry and size of the flow channel. Ore pass channel design is relatively simple since regular cross-sectional shapes are used

Jan 1, 1981

By L. L. Handy

The development of a theory for miscible liquid displacement requires evaluation of the variables which affect growth of the mixing zone between solvent and displaced oil. Factors which appear to be important are individual fluid viscosities, viscosity ratios, flood rate, fluid densities, flow characteristics of the porous medium and molecular diffusion coefficients of the fluid components. The primary purpose of this paper is to evaluate diffusion effects. Theoretical treatments to date have been limited to floods for which the viscosity ratio is one. Two principal theories have been proposed. Von Rosenberg adapted for porous media a theory derived for capillary tubes by G. Taylor.' ,' In this theory molecular diffusion perpendicular to the direction of flow is a primary factor in sharpening the flood front. Slow floods give sharper fronts for a given distance traveled than fast floods. An alternative theory considers miscible liquid displacement as a statistical problem.3,4,5 Diffusion is not an important factor in this theory, but it leads to the same general type of equation as von Rosenberg's. Both theories predict S-shaped concentration profiles with the same dependence on distance traveled. The statistical or "dispersion" theory predicts rate independence, however. To supplement rate studies a direct measurement of a diffusion effect would be helpful in evaluating which of the two proposed mechanisms best describes miscible liquid displacement for one-to-one viscosity ratio systems. No quantitative theory has been proposed for floods in which a low-viscosity fluid displaces a high-viscosity fluid. It might be anticipated, however, that the extensive fingering observed in floods with adverse viscosity ratios would increase opportunities for an exchange of components between displaced and displacing liquids by a diffusional process. Even if molecular diffusion were not an important mixing mechanism for one-to-one viscosity ratio systems, it could be significant in systems with adverse viscosity ratios. METHOD FOR EVALUATING DIFFUSIONAL MIXING In solvent flooding the displacing liquid can become mixed with the displaced liquid by a number of processes; in general, either mechanical or diffusional in character. To evaluate the contribution of diffusion, a method was sought that would distinguish diffusional mixing from mechanical mixing. Suppose two soluble tracers are added to the displacing liquid and that one tracer has a diffusion coefficient much greater than the other. Then, if diffusion is important during miscible liquid displacement and if diffusional transport is primarily transverse to the direction of flow, substances with high diffusion coefficients will have sharper concentration profiles than those with comparatively low molecular diffusion coefficients. In order to have material balance the profiles for the two tracers must intersect. For one-to-one viscosity ratios the intersection would occur at the 50 per cent concentration point. It is generally assumed that diffusion in the direction of flow is negligible. This assumption appears reasonable because flow velocities are ordinarily orders of magnitude greater than diffusional velocities. If this is not a valid assumption, however, the shapes of the fronts will be further degraded by longitudinal diffusion. The effects of rate and molecular diffusion coefficients are the opposite for longitudinal diffusion to those for lateral diffusion. Higher rates or lower diffusion coefficients would tend to give sharper fronts. The double tracer method offers several unique advantages in evaluating effect of molecular diffusion. First, the method gives a direct measure of the effect of diffusion on mixing zone size. Second, the effect of a difference in diffusion coefficients is determined from a single experiment. Comparison of several experiments at different rates is not required. Third, the method is applicable for any viscosity ratio. Fourth, the method is unaffected by density differences between the two fluids which might result in rate dependent gravity effects. EXPERIMENTAL PROCEDURE Suitable tracers are substances whose diffusion coefficients differ as widely as possible, but whose adsorptions on rock surfaces is negligible. The two tracers selected were methanol and sucrose in water solutions. The approximate diffusion coefficients for methanol and sucrose, as given in the International Critical Tables, are 1.3 X 10-5 and 0.3 X 10-5 m2/sec, respectively. Concentrations in the water solutions were 200 gm/liter of solution for both methanol and sucrose. These high

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

Hydrogen forms a beta-stabilized system with titanium, with a beta eutectoid at about 300°C and 44 atomic pct H2. 'The solid solubility of hydrogen in alpha decreases from about 8 to about 0.1 atomic pct from 300°C to room temperature. Hydrogen has little effect on tensile properties, but decreases notch-bar toughness to a large degree. This latter effect appears to be the result of increased notch sensitivity. PRIOR to this investigation, only a small amount of information was available on the effect of hydrogen on the mechanical properties of titanium. The effects of the other interstitially soluble elements, carbon, oxygen, and nitrogen, had received detailed study. Jaffee and Campbell1 indicated that hydrogen up to 1 atomic pct did not affect tensile properties deleteriously. Pitler' indicated that 1 atomic pct H, in titanium reduced the impact strength appreciably, but his alloys contained appreciable amounts of oxygen, and it was difficult to attribute the embrittlement entirely to hydrogen. The high temperature portion of the equilibrium diagram for the Ti-H system was established by McQuillan," and his data generally corresponded with the results of Kirschfeld and Sieverts," Gibb and Kruschwitz," Bevington, Martin, and Mathews," and other investigators. The lower concentration limit of the hydride phase varied considerably among investigators, and Gibb and Kruschwitz9 ad shown that small amounts of contaminants in either titanium or hydrogen caused considerable variation in this lower limit. In view of this pronounced effect of contaminants, the extrapolated value of McQuillan's, about 48 atomic pct at the 325°C eutectoid, appeared the most reasonable. McQuillan's lowest experimental value was 54 atomic pct at a temperature of 450 °C. The density of titanium had been shown to decrease with increasing hydrogen content, but discrepancies were noted among the various investigations. The best values indicated that the density was decreased from 4.56 grams per cc at 0.27 atomic pctl to 3.84 grams per cc at 61.3 atomic pct? This investigation was conducted to determine the effects of hydrogen on a titanium, both in high purity and commercially pure metals, and on high purity a titanium alloys. Material and Fabrication The literature indicated that impurities in either the hydrogen or the titanium must be kept to a minimum. For this reason, the initial studies were made with high purity iodide-refined titanium. The vendor's analysis of the iodide titanium and the hydrogen content of the as-fabricated Y4 in. diameter rods are shown in Table I. Two 1 lb ingots were prepared by arc melting under argon in a water-cooled crucible, using a water,cooled tungsten electrode. This equipment has been described.' As-cast Brine11 hardness numbers of 88 and 58 for these ingots were low enough to insure that the high purity of the metal was maintained during arc melting. The ingots were hot forged to % in. diameter rods at 800°C, cleaned by grit blasting, and then cold swaged to Yz in. diameter rods. The rod was then air annealed at 725 "C, ground to remove scale, and cold swaged to Y4 in. diameter (75 pct reduction in area). The material was then annealed for 1 hr in argon at 800°C to develop an equiaxed a grain size of about 0.05 mm. Micro tensile specimens and microimpact specimens were machined from this rod prior to treatment in the Sieverts-type absorption apparatus. Two lots of commercially pure RC-55 titanium were also used in this investigation to determine the effects of hydrogen and the normal impurities on mechanical properties. The commercially pure RC-55 alloy was obtained in the form of % in. diameter rod. The analysis of this material is also given in Table I. The % in. diameter rods were hot swaged

Jan 1, 1955

By Richard H. Hopkins, R. W. Kraft

A new technique facilitating the rapid determination of the three-dimensional morphology of phases suspended in an opaque matrix is described. The vapidity of the technique is based upon continuous cinephotomicrographic recording of specimen microstructure as the specimen surface is removed under controlled conditions in an electrolytic cell. The advantages of the technique for determining spatial morphologies in opaque materials are illustrated by application of this method to the study of the configuration of faults in a specimen of directionally solidified CuAl2-Al eutectic alloy. A spatial model of the eutectic fault network deduced in this manner has substantiated the facts that faults in this alloy tend to lie parallel to one another in a direction close to that of the specimen growth axis and that the majority of faults tend to bridge lamellae rather than run parallel to them as growth proceeds. For the specimen studied fault density decreased as growth proceeded. ALTHOUGH metallographic observation is a powerful tool for investigating the correlation between structure and properties in metallic alloys, ordinary metallographic methods suffer the fundamental limitation that any conclusions concerning the three-dimensional structure of these opaque materials must rely upon inference from two-dimensional microsections. For this reason it is frequently impossible to make valid judgments regarding the true spatial distribution of the micro-constituents in specimens under investigation. Several techniques have been devised to circumvent the basic limitation of planar microsec-tioning and employed with varying success. These include construction of three-dimensional models of alloy microstructure from sequences of photomicrographs,1-3 quantitative deduction of spatial features based upon statistical studies of data from random and/or selected plane microsections,4-6 and selective dissolution of one phase in a two-phase alloy to reveal the topography of the phase remaining.' However these techniques also have certain obvious disadvantages. Construction of three-dimensional models is a very time-con- suming procedure due to the tedious polish-etch-photograph cycle needed to obtain the necessary photomicrographs to portray the spatial microstructure. Statistical methods by their very nature give only average values of the quantities being studied and cannot therefore give a detailed physical picture of the microstructure to be observed. Finally, the technique of selective dissolution is only applicable in systems where the phases are of vastly different chemical reactivity; it is of little use in the study of single-phase alloys. Since the determination of the three-dimensional structure of opaque materials is hindered by two facts—the materials are opaque to radiation in the visible spectrum and construction of spatial models of microstructure is quite laborious—two solutions to the problem suggest themselves: 1) use radiation of energy great enough to render the alloy transparent, i.e., some microradio-graphic method, or, 2) devise a rapid means to section and record alloy microstructure. Stereomicroradiography has indeed been used to study internal arrangements of phases in several materials8,9 but the method, in general, is limited to very thin specimens (due to X-ray absorption) and simple microstructures. It would seem then that development of a rapid, simple, and generally applicable technique for studying the details of alloy microstructures in three dimensions can best be undertaken by following the second approach above. Using this idea a new technique for rapid evaluation of spatial microstructures was developed based upon cinephotomicrographic recording of the micro-structure of a specimen undergoing controlled electrolytic dissolution. It was further felt that application of this technique to the careful study of the spatial configuration of faults in a CuAl2-Al eutectic alloy would yield information that could be correlated with the extensive data3,6,10-12 already compiled concerning the solidification and crystallography of this eutectic. The practicality and usefulness of similar methods for studying three-dimensional features in alloys has recently been illustrated by the study of dislocation loops in zinc13 and spheroidized structure in steel.14

Jan 1, 1965

By M. S. Azun

I do not at all agree with the basic points of the author's conclusion. The use of lognormal or normal model to respond to the attribute distribution function should be carefully questioned. If fitting a distribution function of regionalized variables is the main purpose, one may employ one of certain well-known families of distributions, such as Tukey's lambda functions. For instance, the distribution function of gold assay values studied by Krige (Krige, 1978) may fit the lognormal model well, but one should not exclude that the basic idea of using the distribution function of observed data is to have insight of the physical mechanism that gives rise to the regionalized variables. In Applied Geostatistics, there are many examples considering only lognormal or normal model for the distribution function of geostatistical data even if the observed distribution function has more than one mode. Of course, using lognormal or normal model always brings easy computation for the statistical properties of attribute under investigation. Still, I object to adopting any of those models without having any "statistical inference." As seen from the author's paper, lognormal and normal model produce the same average grade (0.746% copper) and almost the same sample variance. Therefore, which model explains the probabilistic behavior of ore deposit is always an important question that should be replied by the geostatistician using not the common sense but the statistical and probabilistic methods. For kriging procedures, such as linear kriging, one should describe either second order stationary properties or bivariate properties of regionalized variables. Second order properties, such as correlogram function or semivariogram function, are the inputs of the so-called kriging equations. Selecting one of any useable models for the observed second order properties, such as spherical model, is not easy since the models are not based on the correlations structure of the regionalized variables. How those models being used in Applied Geostatistics can be distinguished is another important problem. One may develop many fitting models to respond to the observed second order properties of regionalized variables. However, I suggest that the model should be based on the probabilistic behavior of geologic process. The author used spherical model for copper, wolfram, and silver grades from isotropic sector (Fig. 2, 4, 3b) and exponential model for silver grades obtained along raises in isotropic sector (Fig. 3a). It seems that those semivariograms given in Fig. 3b for isotropic sector and Fig. 4 may be described by the random model implying that regionalized variables do belong to renewal process (Azun, 1983). If I knew the total number of data points used in estimation, may prove that my conclusion is correct. Recalling the test for the first order sample correlogram value, the test procedure is introduced such that the independence is rejected if [Ir(1) I > Za/2 N1/2] where Za/2 is the a/2 percentile of standard normal random variable and N is the total number of samples used in estimation (Azun, 1983). For the other observed semivariogram functions I suggest the author might try to use the so-called "Markovian model" describing not only the correlation structure of regionalized variables, but also the physical mechanism that produces the regionalized variables. The Markovian model for correlogram function is, [p (h) = T 1ih , h>1 ,] The Markovian model for the other second order properties of ReV are also derived. [T veß], in the above equation, show, for example, structural change and mineralizational variation in a considered deposit, respectively (Azun, 1983). In selecting any model, it is not easy to search for the "best" response to the observed second order properties of ReV's. The Markovian model, based on a theoretical understanding of underlying mechanism, gives more information about the occurrence of regionalized variables and respond to all properties. Random model and the so-called hole effect structure can be easily defined as a special form of the Markovian model (Azun, 1983). An estimation of any second order properties of regionalized variables may be computed through (N-1) lag. However, the dependency between the regionalized variables may be deemed to have "died out" after the so-called stationarity width (range). In practice, the estimation is carried out through 25% of the total number samples available. Therefore, the large fluctuations around the zero level and variance for correlogram or covariogram function and semivariogram function, respectively, cannot be observed. Since the number of pairs involved in the estimation of higher second order properties is small, the estimation variance at those lags is large. There is no need to show higher order estimated second order properties. After using one of any kriging procedure for block estimation, the distribution function of average grades has the same mean as the drilling sample grades but

Jan 1, 1986

By G. A. Vissac

O. R. LYONS *—I wish to thank Mr. Vissac for his compliment. I hope that his paper is not only well received, but that it will serve to bring forth more papers on the subject of thermal drying. One of the primary purposes of the work performed by Battelle for Bituminous Coal Research in investigating the thermal drying of coal was to stimulate other investigators and to get them to contribute their knowledge in the form of papers such as this one. We at Battelle and the personnel of Bituminous Coal Research are very gratified that Mr. Vissac and other persons have responded in this matter of the thermal drying of coal. I wish to state that I think that Mr. Vissac's paper is a very clear and easily understood description of a method of calculating the design requirements for a screen type drier, and I think that it would be exceedingly valuable to operators and to those who intend to purchase any type of thermal drier and use it in the future, if the manufacturers or operators who have such information for other types of driers would provide the same type of information for the other makes of driers now on the market. 1 also wish to point out—an idea that is new to me, and I know is new to most of the operators of driers in the United States-—the idea of recovering the heat that is normally lost in the coal and in the exhaust gases. This heat is not being recovered at most (of the thermal drying operations in the United States, and the possibility of recovering it should be called to the attention of every single one of those operators. I know many of them have never given any thought to the matter, but they will be interested once they realize the ease with which it could be done and the savings that could be realized. I also wish to compliment Mr. Vissac for presenting the method of analysis that he uses to determine the difficulty of drying any particular coal. It is a very simple method, and yet it seems to me that it should be a very effective, very efficient method for determining the difficulty of drying for his particular problems. C. Y. HEINER*—I do not know that I can add anything very illuminating to what Mr. Vissac has said. I think anything that Mr. Vissac said in regard to coal drying is a contribution because, to my personal knowledge, he has studied the matter carefully for many years and made many valuable contributions. I am not too familiar with coal drying problems in the east, but I know in the west we have not made enough coal drying studies. I think coal operators too often just take the coal as it is and make more or less the best of it. There are relatively few washing plants in the west now, and so the problem has not come to the front as much as it probably will in the future. In this connection, it seems to me that this matter of drying the raw coal, as Mr. Vissac brings up, is an extremely important one. We have not a continuous miner ourselves, yet, but we expect to get some this year, and we think the percentage of fine coal-—that is, minus 3/16 in.—will double. We have about 20 pct minus 3/16 in. in the 8 in. by 0 size now, and we think we will likely have 40 pct, which will have a surface moisture of the order of 8 pct. To wash it satisfactorily, we will have to dry the raw coal first in order to screen it, and after that, I suppose, there will have to be dry cleaning of some sort. We have not really used dry cleaning on fines in the west yet to my knowledge, but it is a matter that has to be faced by the industry, and I am very hopeful that Mr. Vissac's study will assist us in that connection. W. L. McMORRIS*-In my company we are preparing largely metallurgical coal for a great number of byproduct coke plants. The most outstanding thing to me about the requirements of moisture in the finished product is that there is a different requirement for almost every coke plant. Each operator has a different set of factors on which he establishes his coking costs where they involve moisture. For our corporation operations in Birmingham, my company does not produce the coal, but in Birmingham they are getting away with moistures very much higher than our plant at Clairton, Pa., would tolerate. The moisture that we have to produce for the plants along the lakefront where they are subject to much more severe weather is something else again. We have not tackled heat drying, primarily because our customers do not know what heat drying will do to the coking characteristics of the coal. If the temperature of drying can be held down

Jan 1, 1950

By H. E. Stauss, J. Hino

INTEREST in silicon has arisen again in the past decade as a result of improvements in crystal rectifiers.' Although the preparation of silicon was first reported by Berzelius in 1880, the early product was of relatively low purity, and only the need for rectifiers in World War II led to the production of a 99.9+ pct pure powder. This material in crystalline form was consolidated into massive silicon for use, and the method developed was to melt it with selected added constituents as "doping" agents. Melting techniques, therefore, are of great importance. There are two basic problems in producing silicon ingots free of doping additions; one is the prevention of spitting and the other is prevention of cracking of the ingot during freezing. The most satisfactory arrangement yet developed for producing massive silicon is to melt and freeze in a cylindrical quartz crucible surrounded by a concentric heating element and concentric radiation shields or insulation. For example, use can be made of a tubular heater with a high frequency generator as the source of power and reflecting shields of alundum cylinders. The spitting of silicon is related to gas evolution, and the gas comes from two primary causes—adsorbed gas and the reaction products of silicon and the crucible. Gas is also released from bubbles contained in the quartz crucible walls. Improved removal of adsorbed gas can be achieved by means of controlled melting and freezing. The seriousness of the problem in vacuo is reduced with an electrically operated mechanical movement of the high frequency power coil. The upper portion of the powder charge is melted first and the high frequency coil lowered until the powder is completely molten. During cooling the high frequency coil is raised slowly. These means also reduce the final nonviolent extrusion of large beads of metal through the ingot top during freezing. Better control of spitting and bead extrusion is obtained when melting is done under helium at. atmospheric pressure instead of in vacuo. The problem of reaction between silicon charge and crucible in practice is confined to the reaction between silicon and quartz. This2 apparently is: Si + SiO2 + 2SiO The part that this reaction plays in spitting has not been isolated for separate study. SiO is a volatile vapor at the melting point; of silicon and is released freely during melting in vacuo, but hardly at all in helium at atmospheric pressure. The cracking of ingots is a major difficulty in melting silicon, and its prevention requires special melting techniques or the addition of "toughening" agents such as aluminum or beryllium.' The cracking of the ingots has been explained as being the result of the expansion that occurs upon freezing; although direct observation of freezing ingots reveals visible cracks on the surface only after a red heat has been reached, suggesting that cracking is the result of differential contraction of silicon and quartz. Silicon wets quartz, and the ingot adheres tightly to the crucible. Therefore as ingot and crucible cool, the two either have to pull apart, or at least one must crack. Surprisingly, in spite of the relative thinness of the quartz and the thickness of the ingot, the ingot and the crucible both crack. Microscopic and X-ray4 studies fail to show any plastic flow other than twinning in the ingots. Slow cooling fails to prevent cracking. Another possible solution to cracking is to weaken the crucible. Use of thin-walled crucibles finally led to success with fused quartz crucibles with a wall thickness of 0.25 to 0.50 mm. With such thin-walled fused quartz crucibles consistently uniform success is secured in producing sound ingots 30 mm in diam from the purest available grade of silicon (99.9+) without the use of any type of addition. Melts are made in the size range of 50 to 100 g. Omission of a deliberately added doping agent is not sufficient to insure pure ingots. The reaction of silicon with crucibles and the resultant solution of impurities in the silicon is well-established." In this laboratory, the presence of Al, Be, and Zr has been found spectroscopically in ingots melted in contact with alumina, beryllia, and zircon. The best crucible materials reported in the literature are MgO and SiO2. Use of MgO in this laboratory has resulted in a heavy deposit of magnesium on the furnace walls, showing that a reduction of the magnesia occurred and the resulting magnesium removed from the melt by volatilization. In the case of quartz, the silica is reduced and SiO liberated to deposit on the equipment walls. There probably is real danger that oxygen is dissolved in the ingot when either magnesia or silica is used as the crucible material. Preliminary analyses by Dean Walter in his vacuum unit in this laboratory6 indicate the presence of oxygen in undoped silicon melted in quartz.

Jan 1, 1953

By J. C. Swartz

New measurements of graphite and cementite solubilities in ferrite have been obtained to resolve disagreements among previous data. To measure graphite solubility, specimens of iron were equilibrated with rarious carburizing atmospheres at temperatures be-twee~z 480" and 1435°C. The carbon activity of each atmosphere relative to graphite was taken from published data. After quenching from each equilibration treatment the concentration of carbon (typically 10 pprn by wt) was determined from the height of the Snoek peak in the internal friction spectrum. A few inclividual analyses by combustion support the reszdts of Smith on the solubility of graphite near the eutectoid temperature. Combination of these combustion and internal friction analyses determines In a, (at 0.01 wt pct) = 24,000/RT - 12.72, where a, is the activtity relative to graphite in ferrite at fixed cornposition. The same specimens were used to determine the solubility of self-stressed cementite precipitates. The results indicate solubilities of 6.3, 23.2, and 68 pprn carbon by wt at respectively 400°, 500". and 600°C. The once large discrepancy between the cementite solubility determined by internal frictiori and that calculated from flee energy data has been almost completely resolved. A recent study1 (hereafter designated I) on the solubility of cementite in a iron did not fully resolve the disagreement among previous data. The remaining disagreement is illustrated by the phase diagram in Fig. L The data of I are represented by the line labeled "stress-free" cementite. They determine a heat of solution of cementite of (14.8 * 0.2) kcal per mole which contrasts with the (20 * 1) kcal per mole derived from Smith's graphite solubility2 and the formation energy of cementite.3 Toward resolving this disagreement we have obtained new data on the solubilities of graphite and cementite. METHODS As in I the Snoek peak in the internal friction spectrum was used to measure the concentration of carbon dissolved in ferrite. This method relies on the relation C=kQ-1 [1] in which C is the concentration of dissolved carbon, Q-I is the Snoek peak height, and k is a proportionality factor which is a function of the peak temperature, polycrystalline texture, and other parameters characteristic of the ferrite lattice. To determine true heats of solution via Eq. [1], it is necessary to establish that k is independent of the temperature from which the specimen is quenched. Some evidence on this point is contained in a separate report.* Additional evidence is shown by the data points in Fig. 1. These represent the Snoek peaks of two specimens carburized to about 10 ppm C, copper plated, and quenched first from 888º then from 588°C. The copper plate was removed before each Snoek peak measurement. These data show that there is no detectable dependence of k on quenching temperature. The solubility of graphite was determined by repeatedly carburizing various specimens of iron wire with gas mixtures of known carbon activity relative to graphite. To cover a wide temperature range within the a phase boundaries it is desirable to use as low a carbon concentration as is compatible with reasonable precision. With the present internal friction apparatus the best compromise of these desires is a concentration near 10 wt ppm. The dashed line in Fig. 1 was used to approximate the activity of carbon* for

Jan 1, 1970

By S. J. Sindeband

Prior to discussing the metallurgy of sintered chromium borides, it is pertinent to outline some of the reasoning behind this investigation and the purposes underlying the work. This study was initiated as an aproach to the ubiquitous problem of a material for service at high temperatures under oxidizing atmospheres, and it was undertaken with a view to raising the 1500°F (816°C) ceiling to 2000°F (1093°C) or better. For the reason that no small, but rather a major, lifting of the high temperature working limit was being attempted, it was felt appropriate that a completely new approach be taken to this problem. A summary of the thinking behind this approach was published recently by Schwarzkopf.' In briefest terms, it was postulated that the following requirements could be set up for a material which would have high strength at high temperatures. 1. The individual crystals of the material must exhibit high strength interatomic bonds. This automatically leads to consideration of highly refractory materials, since their high energy requirements for melting are related to the strength of their atom-to-atom bonds. 2. On the polycrystalline basis, high boundary strength, superimposed on the above consideration, would also be a necessity. Since this implies control of boundary conditions, the powder metallurgy approach would hold considerable promise. Such materials actually had been fabricated for a number of years, and the cemented carbide is the best example of these. Here a highly refractory crystal was carefully bonded and resulted in a material of extremely high strength. That this strength was maintained at high temperature is exhibited by the ability of the cemented carbide tool to hold an edge for extended periods of heavy service. Nowick and Machlin2,3 have analytically approached the problem of creep and stress-rupture properties at high temperature and developed procedures whereby these properties can be approximately predicted from the room temperature physical constants of a material. The most important single constant in the provision of high temperature strength and creep resistance is shown to be the Modulus of Rigidity. On this basis, they proposed that a fertile field for investigation would be that of materials similar to cemented carbides, which have Moduli of Rigidity that are among the highest recorded. The cemented carbide, however, does not have good corrosion resistance in oxidizing atmospheres and without protection could not be used in gas turbines and similar pieces of equipment. It would be necessary then to attempt the fabrication of an allied material based upon a hard crystal which had good corrosion resistance as well. It was upon these premises that the subject study was undertaken and at an early stage it was sponsored by the U.S. Navy, Office of Naval Research. Since then, it has been carried on under contract with this agency. Chromium boride provided a logical starting point for such research, since it was relatively hard, exhibited good corrosion resistance, and, in addition, was commercially available, since it had found application in hard-surfacing alloys with iron and nickel. That chromium boride did not provide a material that met the ultimate aim of the study results from factors which are subsequently discussed. This, however, does not detract from the basis on which the study was conceived, nor from the value of reporting the results which follow. Chromium Boride While work on chromium boride proper dates back to Moissan,4 there has been a dearth of literature on borides since 1906. Subsequent to Moissan, principal investigators of chromium boride were Tucker and Moody,5 Wede-kind and Fetzer,6 du Jassoneix,7,8,9 and Andrieux." These investigators were generally limited to studies of methods of producing chromium boride and detennining its properties. Some study, however, was devoted to the chromium-boron system by du Jassoneix,7 who did this chemically and metal-lographically. This system is not amenable to normal methods of analysis by virtue of the refractory nature of the alloys involved, and the difficulties of measurement and control of temperature conditions in their range. Dilatometric apparatus is nonexistent for operation at these temperatures. Du Jassoneix made use of apparent chemical differences between two phases observed under the microscope and reported the existence of two definite compounds, namely: Cr3B2 and CrB. These two compounds, he reported, had quite similar chemical characteristics, but were sufficiently different to enable him to separate them. The easiest method for producing chromium boride is apparently the thermite process, first applied by Wede-

Jan 1, 1950

By F. A. Forward, J. Halpern

A new process for extracting uranium from ores with carbonate solutions is described. Leaching is carried out under oxygen pressure to ensure that all the uranium is converted to the soluble hexavalent state. By this method), alkaline leaching can be used successfully to treat a greater variety of ores, including pitchblende ores, than has been possible in the past. The advantages of carbonate leaching over conventional acid leaching processes are enhanced further by a new method which has been developed for recovering uranium from basic leach solutions. This is achieved by reducing the uranium to the tetravalent state with hydrogen in the presence of a suitable catalyst. A high grade uranium oxide product is precipitated directly from the leach solutions. Vanadium oxide also can be precipitated by this method. The chemistry of the leaching and precipitation reactions are discussed, and laboratory results are presented which illustrate the applicability of the process and describe the variables affecting leaching and precipitation rates, recoveries, and reagent consumption. THE extractive metallurgy of uranium is influenced by a number of special considerations which generally do not arise in connection with the treatment of the more common base metal ores. Perhaps foremost among these is the very low uranium content of most of the ores which are encountered today, usually only a few tenths of one percent. A further difficulty is presented by the fact that the uranium often occurs in such a form that it cannot be concentrated efficiently by gravity or flotation methods. In these and other important respects, there is evident some degree of parallelism between the extractive metallurgy of uranium and that of gold and, as in the latter case, it has generally been found that uranium ores can best be treated directly by selective leaching methods. It is readily evident that this parallel does not extend to the chemical properties of the two metals. Unlike gold, which is easily reduced to metallic form, uranium is highly reactive. It tends to occur as oxides, silicates, or salts. Two ores are of predominant importance as commercial sources of this metal: pitchblende which contains uranium as the oxide, U3O51 and carnotite in which the uranium is present as a complex salt with vanadium, K2O-2UCV3V2O5-3H2O. These ores may vary widely in respect to the nature of their gangue constituents. Some are largely siliceous in composition, while others consist mainly of calcite. Sometimes substantial amounts of pyrite or of organic materials are present and these may lead to specific problems in treating the ore. Further complications may be introduced by the presence of other metal values such as gold, copper, cobalt, or vanadium whose re- covery has to be considered along with that of the uranium, or whose separation from uranium presents particular difficulty. In general, there are two main processes for recovering uranium in common use today.'.2 One of these employs an acid solution such as dilute sulphuric acid to extract the uranium from the ore. A suitable oxidizing agent such as MnO, or NaNO, is sometimes added if the uranium in the ore is in a partially reduced state. The uranium dissolves as a uranyl sulphate salt and can be precipitated subsequently by neutralization or other suitable treatment of the solution. The second process employs an alkaline leaching solution, usually containing sodium carbonate. The uranium, which must be in the hexavalent state, is dissolved as a complex uranyl tricarbonate salt, and then is precipitated either by neutralizing the solution with acid or by adding an excess of sodium hydroxide. The latter method has the advantage of permitting the solutions to be recycled, since the carbonate is not destroyed. This is essential if the process is to be economical, particularly with low grade ores. With each of these processes, there are associated a number of advantages and disadvantages and the choice between using acid or carbonate leaching is generally determined by the nature of the ore to be treated. In the past, more ores appear to have been amenable to acid leaching than to carbonate leaching and the former process correspondingly has found wider application. With most ores, acid leaching has been found to operate fairly efficiently and to yield high recoveries. One of the main disadvantages has been that large amounts of impurities, such as iron and aluminum, sometimes are taken into solution along with the uranium. This may give rise to a high reagent consumption and to difficulties in separating a pure uranium product. Excessive reagent consumption in the acid leach process also may result

Jan 1, 1955