Search Documents

By S. S. Solomons, V. H. Tillmann, L. Smaniotto

INTRODUCTION The Zinc Corporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) mines are situated at Broken Hill, New South Wales, Australia (refer Fig. 1). Both companies are wholly owned subsidiaries of Australian Mining and Smelting Limited (AM&S). Annual production from both mines is 2.3 million tonnes of lead, silver and zinc ore mined by a variety of underground methods. From 1911 to 1968, conventional overhand cut and fill stoping (both open and square set timber) was used almost exclusively, though some trials with shrinkage and sublevel stoping were undertaken. The trial stopes used short holes in conparison with today's sublevel open stopes. Mechanised cut and fill methods with regular rockbolt support were introduced in the early 1960's and undercut and fill stoping replaced square set timber stoping for pillar extraction in the late 1960's. Since 1968, increasing emphasis has been placed on longhole open stoping (LHOS) although some areas of the orebodies are comrnrnitted to the abovemehtioned methods since existing stope development makes it impracticable to change. In 1979, approximately half the total production was mined by LHDS and it is expected that the LHOS proportion will increase in the future. A vertical crater retreat method of longhole mining has also been successfully introduced to replace the undercut and fill stoping of some pillars and it is expected that this stoping method will be used in some future primary ore extraction. This paper reviews the progress of LHOS technology at ZC/NBHC with emphasis on the stope planning and design process and the importance of rock mechanics applications. The objective has been to maximise the primary extraction of the orebody giving due consideration to stability and safety. This has led to the design of a novel sloped wall longhole stoping method which should eliminate the formation of pillars by mining the orebody in a "continuous" manner incorporating a sloped sand interface between the blocks of ore being mined and the previously mined sandfilled stope. The expected results include the complete extract of the orebody without the formation of pillars and with minimal dilution of ore with sandfill. The evolution of the method can be best illustrated by following the mining progress of the relatively new Southern 'B1 Lode orebody at the NBHC mine. GEOLOGY Southern '8' Lode is the southern extension of the 'Bt Lode orebody, which is currently being mined further to the north in ZC/NBHC (refer Fig. 2). The ore block being developed and stoped extends for a vertical height of 90 metres from No. 17 level down to approximately ten metres above No. 19 level. The ore minerals are sphalerite and galena with the zinc:lead ratio averaging approximately 3:l with a minor amount of silver associated with the galena. There is a sharp contact between the ore and the country rock on the footwall and keel, while the hanging wall gradates into medium and low grade material. The gangue is primarily quartz together with garnet, biotite, feldspar, gahnite, sericite and minor apatite. In various horizons within the orebody, grey feldspar, quartz and garnet pegmatites occur as stratiform layers. The ore and country rock are competent with some inconpetent boundaries.

Jan 1, 1981

By H. H. Spain, R. C. Rumble, H. E. Stamm

This paper presents a reservoir analyzer study of the performance of the Woodbine formation in the East Texas basin. The study was made possible by the compilation of available information on the configuration. thickness and the pressure drawdown of the formation. The investigation was made of the pressure variations in the basin incident to production from the several Woodbine reservoirs. In addition, the apparent compressibility of Woodbine water was evaluated so that the potential water yield of the formation could be determined. The distribution of permeability of the Woodbine sand and the interference between producing areas were also investigated. In conjunction with this basic study of the Woodbine sand, an acceptable match of the production-pressure relationship in the East Texas Field was established on the analyzer. INTRODUCTION When production is taken from a reservoir contiguous to an aquifer, the resultant pressure gradient causes a water influx into the reservoir. For some years it has been the practice to predict the performance of water drive reservoirs with mathematical equations that relate the water influx into reservoirs to their pressure behavior. A rigorous solution of these equations is quite complex: hence, the conventional method requires the simplifying assumptions that the formation have constant thickness, permeability and poiosity, and that it have a known and regular shape. It is necessary to use performance records of the reservoir in question to determine the equation constants that make the results of the mathematical calculations duplicate the reservoir history. The values of the constants determined in this manner sometimes differ so greatly from theoretical or measured values that the constants appear unreasonable. The equation constants comprise such factors as the thickness, porosity and permeability of the formation, and the viscosity and compressibility of water. Usually the thickness, porosity and viscosity are known within a reasonable degree of certainty. whereas the formation permeability and the water compressibility are known with considerably less certainty. Hence. permeability and compressibility values are arbitrarily selected that will make the mathematical equations duplicate the reservoir behavior. In many reservoir studies the value of the compressibility of water thus selected has exceeded the reported value by a factor of from severalfold to manyfold. Whether this excessive value results from the inadequacy of the mathematical approach to take into account the shape irregularities and the heterogeneities of the aquifer, or is due to some type of formation compaction and decrease of porosity has not been established. Because of the significance of the potential water yield of formations with reference not only to oil reservoirs but to water resources as well, it is very important that a representative value for the effective water compressibility be determined. One of the best known examples of a field for which it has been possible in the past to predict the future reservoir pressure is the East Texas Field. Until about 1943 it was possible by means of mathematical equations to duplicate past pressure behavior and to predict with a high degree of accuracy the reservoir pressure of the field. Since 1943, however, the calculated pressures have deviated progressively from the observed pressures to such a degree that in recent years, it has

Jan 1, 1951

By Nicholas J. Grant, Bill C. Giessen

The phase diagram Ta-Ni has been treated repeatedly; investigations up to 1958 are summed up in Ref. 1. Since then, an equilibrium diagram has been presented by Kornilov and Pylaeva.2 They found the following intermediate phases: Ta2N; (CuA12 type),3 "TaNi" (p phase, Mo8Co7 type), TaNiz, and TaNi3 (Ticus type).5 Of these, the crystal structure of TaNin remained unknown, and no further literature reference was found. According to Kornilov and pylaeva,&apos; TaNil melts peri-tectically at 1420°C. A 5-g alloy of Ta + 66.7 at. pct Ni was prepared by inert-gas arc melting using 99.95 pct Ta rod (NRC-MG) and 99.9 pct Ni shot (Fisher). The weight loss after three melts was <2 mg; a microscopically homogeneous ingot resulted. As shown in Ref. 6, no oxygen or impurity pickup needed to be considered under these conditions. Specimens were annealed for 15 hr at 1350°C, 15 hr at 1205oC, and 15 hr at 875°C with subsequent powdering and stress relief for 10 min at 1350°C, 15 min at 1205oC, and 1 hr at 875oC, respectively. Micrographs and X-ray analysis (114.6 mm Norelco camera, filtered CuK, radiation) showed homogeneous one-phase alloys in the as-cast state and at all three temperatures, all having the same powder pattern except for broad lines in the as-cast state. From this it is concluded that either TaNi, melts congruently or its melting behavior is a transition between the eutectic and peritectic cases. Since it was found that very slight surface contamination on stress relieving can considerably alter the structure of similar phases (e.g.,TaPt3),7 patterns before and after stress relief were also compared; they were identical except for line broadening in the non-stressrelieved condition, and two faint impurity lines in the stress-relieved samples. The powder pattern is presented in Table I. All lines were accounted for by indexing with a tetragonal lattice, 0Yh- I4/mmm , with a, = 3.154 ± 0.001A, co = 7.905 * 0.002i and c/a = 2.506. The atomic positions are: 1000; 1/2, 1/2, 1/2] + 2Ta(a): 000; + 4Ni(e): *(002); z = 0.333 * 0.002 This proves TaNi2 to be a representative of the MoSiz (Cllb) type. The variable parameter was determined by grouping the visually estimated intensi- ties according to their 2 indices, plotting their F values, and varying z for best fit, which was obtained at z = 0.333= 1/3. Since absorption was not considered, only the relative intensities with similar 28 can be expected to agree. The interatomic distances are presented in Table 11; the standard error is *o.o2A, resulting chiefly from the uncertainty in z. These distances indicate a coordination number 10 for both kinds of atoms and show that the pseudohexagonal layers along (110) are rather un-distorted. The mean atomic volume of 13.1A3 is close to the Vegard&apos;s law value of 13.3A3, showing

Jan 1, 1964

By Frank H. Reed, P. W. Henline, Harold W. Jackman

A sumMary of the consumption of coal in 1945 shows that the coke industry ac-counted for 17 pct of the total coal used. No substitute for coke and the blast furnace in the reduction of iron ore has gained sufficient prominence so far to be given serious consideration. However, while the same slot-type ovens are being built and used now as were in use a few years ago, the problem of obtaining suitable coking coals, both high- and low-volatile, has forced many operators to revamp coal-blending facilities. Until the beginning of World War 11, high-temperature ooke plants were able to secure the required high-volatile and low-volatile coals from two or three seams and from three or four mines. Thus, many of our coke oven plants were able to operate with storage bins for two coals only. The vari-pnce in raw materials was not great, and uniformity of blend was a relatively simple problem. Since the beginning of World War 11, many and important changes have taken place. Demand for all coals increased greatly. Production, though kept as near maximum capacity as possible, could not meet the demands for coal generally, and particularly for the various kinds of coal which have proved to be satisfactory for specialized uses; coals were allocated as nearly as possible in the order of greatest need; storage piling was reduced to the minimum necessary to keep plants in operation; uniformity of quality could not be maintained, and with this last, uniformity of composition of blends for coking could not be maintained. Whereas before the war producers of metallurgical coke could fill their needs from three or four mines, by the end of the war it was not unusual to find shipments to a single coke oven plant coming from as many as 30 different mines, in a single month. Since many of the mines producing both high- and low-volatile coal for high-grade metallurgical coke are rapidly nearing de-pletion, the problem of seeking new sources and of blending a number of coals in each plant for the production of high-temperature coke is facing practically every producer in the United States at the present time, and is one which will probably continue for many years to come. Midwestern byproduct coke ovens in the Chicago and St. Louis areas use annually from 12 to 15 million tons of bituminous coals which are transported 500 to 700 miles from the Appalachian coal fields of Pennsylvania, West Virginia, and eastern Kentucky. Approximately two-thirds of this coal is high-volatile bituminous. The critical transportation problem confronting the nation in 1943, and the growing scarcity of the best Appalachian coking coals, prompted the Illinois Geological Survey to propose a research program in which would be studied the coking properties of blends of low-sulphur, high-volatile Illinois coal with the high- and low-volatile coals from the eastern fields. Such blends containing Illinois coal, if substituted for the all-eastern blends normally coked,

Jan 1, 1949

By K. Barron

The glass insert stressmeter, or photoelastic stressmeter, is an instrument designed to determine stress changes occurring in rocks. It has several potential advantages over other such devices in that it is a biaxial device, it is simple and it is cheap to make. The object of this study was to assess the behaviour of the meter under biaxial loads and to examine some of the problems associated with measurement and interpretation of the fringe pattern. This assessment has been carried out by comparing theoretical and laboratory behaviour of the meter. It has been shown that: a) There are certain optimum measuring points in the meter at which measurements should be made for best accuracy. The position of the points depends on the ratio, n, of the biaxial stresses. b) The meter&apos;s sensitivity can be assumed to be independent of the rock modulus E provided that the rock modulus is < 2.5 x 106 psi and not, as previous workers have assumed, if E < 5 x 106 psi. c) There are several methods of separating the principal stresses; some of these are unsatisfactory. A new method is proposed and discussed. d) The meter sensitivity decreases as the ratio of the biaxial stresses approaches unity; the accuracy thus also decreases. e) The axes of symmetry of the fringe pattern give an excellent indication of applied stress direction. f) Laboratory calibrations are in good agreement with theory. The glass insert or photoelastic stressmeter is an instrument designed to determine stress changes occurring in rocks. It has several potential advantages over other such devices in that it is a biaxial device, it is simple and it is cheap to make. This stressmeter has been described in detail.l,2 Basically it is a hollow glass cylinder that has at one end a light source and filters producing circularly polarized light. The glass cylinder and source are grouted into a borehole in rock and the face of the cylinder is viewed through a quarter wave plate and an analyser. If, after installation, a stress change occurs in the rock, then a distinct colored isochro-matic fringe pattern is seen in the meter. The fringe order at any point in the meter can be determined by counting the fringes and measuring the fractional fringe orders by the Tardy compensation method. The relation between the fringe order at any point and the applied stress change can be determined either by calculation or by calibration. The object of this study was to assess the behavior of this stressmeter under biaxial loading conditions and to examine some of the problems of interpretation of the fringe pattern. THEORY Hiramatsu et a14 have determined the stress distribution in a hollow cylindrical inclusion in an elastic host material when subject to uniaxial stress. Using this solution, the biaxial case of stress p in the x direction and stress q in the y direction (Fig. 1) can be solved by superposition. This has been done in Appendix 1. It is shown that the principal stress difference (s1 -s2) at any point (r,?) in the cylinder is given by:

Jan 1, 1965

By Bernt Ellingsaeter, Terkel Rosenqvist

IN the silicothermic reduction of magnesia, burned dolomite is treated with high grade ferrosilicon in an evacuated steel retort at temperatures between 1150° and 1200°C. The following reaction is assumed to occur MgO + CaO + 1/2 Si (Fe) - Mg(g) +- & Ca,SiO, + Fe with the equilibrium constant on the basis of thermodynamic data for the substances involved and assuming unit activity for all solid constituents, Kubaschewski and Evans&apos; calculated the magnesium pressure as a function of temperature logp,, (mmHg) = 15.06-1.61 T- log T- 13,16O/T. Pidgeon and King," who measured the magnesium pressure by means of a flow method, found values about three times the calculated ones. This may be caused by uncertainties in the thermodynamic data, but may also be caused by the formation of other reaction products, such as Ca,SiO,, which is known to be the stable silicate in equilibrium with lime. Whatever the exact reaction may be, it is evident that as long as all other factors are maintained constant the magnesium pressure will vary with the silicon activity, viz: p,, = &,. (p,,) ", where (p,,)" is the magnesium pressure by the reduction with silicon of unit activity. In the present investigation, p,,, was therefore measured for various grades of ferrosilicon and their silicon activities were calculated. The experimental method was similar to that used by Pidgeon and King. Briquettes of burned dolomite and Fe-Si alloys were placed in a 1 in. heat resistant steel tube and were heated to 1200°C. By means of a flow of purified hydrogen, the magnesium vapor was swept into a condenser filled with steel wool. From the amounts of hydrogen used and magnesium condensed the magnesium partial pressure was calculated. First a tube of 28 pct Cr steel, and later a tube of Kanthal D (a ferrous alloy with 22.6 pct Cr, 2 pct Co, and 4.5 pct Al), was used as a heat resistant tube. The latter tube showed the best heat resistance. The dolomite used had the following composition: 43.6 pct MgO, 55.5 pct CaO, 0.2 pct K,O + NalO, 0.2 pct Fe,O,, and 0.3 pct insoluble. The ferrosilicons were prepared from 98 pct Si of technical grade (0.7 pct Al, 0.3 pct Ca, and 1 pct Fe) by melting with various amounts of electrolytic iron of high purity. The alloys thus obtained were analyzed on their iron and silicon contents, which added up to between 99 and 100 pct. The amounts of reactants were chosen so that there would always be an excess of the oxides, and the average decrease in silicon content during the experiments would be about 1 pct. Most of the reaction occurred in the part of the reaction mixture facing the gas flow. The change in the silicon concentration in the part facing the condenser was, therefore, negligible. To facilitate the reaction, about 1 pct fluorspar was added to the briquette mixture. Fluorspar does not enter the reaction, but is known to act as a

Jan 1, 1957

By R. M. Hardgrove

PULVERIZED coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the difficulties incident to the burning of coal. In a cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverized in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. PROCESS OF BURNING CEMENT CLINKERS The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output. This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,1 in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. WET VS. DRY PLANTS The study presented here covers 88 plants, of which 41 are wet and 47 dry. Of

Jan 1, 1941

By Hans Lundberg

FOR the last 20 years, geophysical methods have been in practical use. The results accumulated during this time have been broad enough to enable us to formulate some general rules for conducting geophysical surveys to the best advantage. It is a well established fact that electrical and magnetic methods have aided the geologist to outline bodies of ore, to differentiate between various types of rocks hidden from view and also to determine the thick-ness of the layer of drift that covers the bedrock. Fundamental require-ments for a successful solution of a geophysical problem is the existence of physical differences between the various formations under investiga-tion. If such conditions exist, our problem becomes a physical, mathe-matical and geological analysis of the effects of these differences upon the structure of an arbitrarily produced, or already existing, field of force. Experience has shown that reliable and consistent results in analyzing such fields of force are obtained only if: (1) the methods and apparatus used are scientifically sound and designed to provide information with a maximum amount of accuracy, reliability, sensitivity, simplicity and speed of operation, and (2) the interpretation of the results of such an investigation is guided not only by rigid mathematical rules but also by common sense, based upon sound geological knowledge and imagination. Today, a number of methods are based upon sound principles, are highly sensitive and are well suited for field work. The instrumental developments have resulted in self-contained instruments, which permit the determination of field ratios and intensities with great accuracy. Magnetic surveys have almost become standardized. The electrical methods, mostly based on the determination of potential-drop ratios, or electromagnetic field ratios, are built as bridge circuits and it is easy to determine amplitude, as well as phase relationship of the various electrical and electromagnetic fields.

Jan 1, 1938

By R. Priestner, R. F. Krause

Solid, cylindrical crystals of a iron have been fractured at 10°K by the simultaneous application of tension and torsion stresses. Thus, a complex distribution of normal (sN) and shear (ss) stresses existed in a cleavage plane at fracture. In every crystal the clearage-plane normal was inclined to the specimen axis, so that a unique point, M*, in the operative cleavage plane was defined where the quantities sn and s2 N + s2 S) were maximized. It is shown that the maxirrzum resolved normal stress on the cleavage plane at fracture decreased as the resolved shear stress in the cleavage plane at M* increased. Thus, a normal stress la?*! for fracture was not satisfied. A fracture law which takes shear stress into account. and which predicts that (s2 N +s2S) should be constant, is to be preferred. However, the data is best represented by a linear dependence of sN on sS, sS which 110 physical significance can be attached. It is suggested that the fracture-nucleating -mechanism is a short-range one. A critical stress law has not yet been unequivocally established for the propagation of cracks in metals. Measurements of the tensile fracture stresses of variously oriented zinc single crystals1 failed to establish the normal stress law expressed by In Eq. [1], sN is the fracture stress, P, resolved normal to the fracture plane, and 0 is the angle between the fracture -plane normal and the stress axis. Similarly, a comprehensive investigation failed to verify the normal stress law for the tensile fracture of a-iron single crystals.&apos; However, a subsequent investigation,3 using iron from the same ingot, presented fracture data which obeyed the normal stress law. It has been shown previously4,5 that the Griffith criterion for fracture6 does not predict such a normal stress law. This result is of particular significance in considering the fracture of metals, such as zinc and iron, which may fail by cleavage. In these metals fracture propagates in a well-defined "cleavage" plane, whether or not an applied stress is normal to it. When the cleavage-plane normal deviates from the direction of application of a uniaxial stress, for example, the crack propagates under the combined action of normal (sN) and shear (ss) stresses. When the presence of a resolved shear stress in the crack plane is taken into account, the Griffith criterion is expressed by4

Jan 1, 1967

By A. V. Deforest, C. W. Macgregor, A. R. Anderson

One of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing or the A.S.T.M., 1938. The work of Mann.&apos; Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserves especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by P ALo plotting So = 1/A0 as a function of eo = ALr,o where A0 and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors.7&apos;8 It was shown that the true physical behavior of the material in the tension test could best be represented P by plotting the average true stress, S = 2P as a function of 6 = q&apos; = log —r = log ~9L where P, A, L, S, E, and q&apos; refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximin load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain dificulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece diameters to fracture under impact conditions offers considerable experimental difficulty. In order to make it feasible to

Jan 1, 1942

By E. W. Newman

During 1943 and 1944, there was an urgent need for certain grades of optical calcite (Iceland spar) for instruments for &apos; military uses. To find a supply of this material, prospecting was carried out in Montana, California and Colorado. Although some production was obtained by the work in California, the best results were from prospecting the large calcite veins of south central Montana. The bulk of the optical calcite mind during World War II has come from that area. The Bureau of Mines took an active part in the search for optical calcite in Montana. It examined most of the known calcite veins in the 70-mile distance between Wilsall, on the Shields River: and Absarokee, on the Still water River, and conducted exploration on several of the deposits. The Geological Survey also took an active part by mapping many of the veins. Actual mining of the calcite was performed at first by Calcite Operators, Inc., and later by the Metals Reserve Co., through an agent. A sorting plant was established at Clyde Park, where custom material could be sold. These activities stimulated mining by private operators. To be suitable for military uses, the calcite mined had to meet rigid specificstions as to both size and quality. Individual crystals had to be clear and transparent and if in the form of rhombs had to measure at least 7/8 in. on each edge. Some color and a few inclusions in the calcite were allowable, but material with incipient or developed cleavages, or showing twinning other than parallel to the base, was unacceptable. History of Deposits The existence of large veins of calcite in south central Montana has long been known, and for many years the farmers of this region have used the common vein calcite for producing grit for chicken feed. According to reports, the fist optical calcite produced from Montana came from the Cartwright deposit near Grey-cliff,&apos; but until recently the mining of optical calcite in Montana has been limited to spasmodic searching for small crystals suitable for making nicol prisms for saccharimeters and microscopes, or for mineral specimens. The possible need of substantial amounts of optical calcite for military uses began to appear late in 1942 and early in 1943, therefore the Polaroid company began searching for a source of supply in Montana and California. Work on the Wade property near Clyde Park was started on a small scale in the fall of 1942, by .4. H. Hansen, of Clyde Park. During the winter and spring of 1943, a modest quantity of optical calcite was mined and shipped to the Polaroid Corporation, Cambridge, Mass. Most of this was produced from the "Hansen vug," which was found close to the surface. Early in the summer of 1943, mining on the Wade property was undertaken by Calcite Operators, Inc., a company organized for mining optical calcite from the

Jan 1, 1948

By E. W. Newman

During 1943 and 1944, there was an urgent need for certain grades of optical calcite (Iceland spar) for instruments for &apos; military uses. To find a supply of this material, prospecting was carried out in Montana, California and Colorado. Although some production was obtained by the work in California, the best results were from prospecting the large calcite veins of south central Montana. The bulk of the optical calcite mind during World War II has come from that area. The Bureau of Mines took an active part in the search for optical calcite in Montana. It examined most of the known calcite veins in the 70-mile distance between Wilsall, on the Shields River: and Absarokee, on the Still water River, and conducted exploration on several of the deposits. The Geological Survey also took an active part by mapping many of the veins. Actual mining of the calcite was performed at first by Calcite Operators, Inc., and later by the Metals Reserve Co., through an agent. A sorting plant was established at Clyde Park, where custom material could be sold. These activities stimulated mining by private operators. To be suitable for military uses, the calcite mined had to meet rigid specificstions as to both size and quality. Individual crystals had to be clear and transparent and if in the form of rhombs had to measure at least 7/8 in. on each edge. Some color and a few inclusions in the calcite were allowable, but material with incipient or developed cleavages, or showing twinning other than parallel to the base, was unacceptable. History of Deposits The existence of large veins of calcite in south central Montana has long been known, and for many years the farmers of this region have used the common vein calcite for producing grit for chicken feed. According to reports, the fist optical calcite produced from Montana came from the Cartwright deposit near Grey-cliff,&apos; but until recently the mining of optical calcite in Montana has been limited to spasmodic searching for small crystals suitable for making nicol prisms for saccharimeters and microscopes, or for mineral specimens. The possible need of substantial amounts of optical calcite for military uses began to appear late in 1942 and early in 1943, therefore the Polaroid company began searching for a source of supply in Montana and California. Work on the Wade property near Clyde Park was started on a small scale in the fall of 1942, by .4. H. Hansen, of Clyde Park. During the winter and spring of 1943, a modest quantity of optical calcite was mined and shipped to the Polaroid Corporation, Cambridge, Mass. Most of this was produced from the "Hansen vug," which was found close to the surface. Early in the summer of 1943, mining on the Wade property was undertaken by Calcite Operators, Inc., a company organized for mining optical calcite from the

Jan 1, 1948

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

One of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing or the A.S.T.M., 1938. The work of Mann.&apos; Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserves especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by P ALo plotting So = 1/A0 as a function of eo = ALr,o where A0 and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors.7&apos;8 It was shown that the true physical behavior of the material in the tension test could best be represented P by plotting the average true stress, S = 2P as a function of 6 = q&apos; = log —r = log ~9L where P, A, L, S, E, and q&apos; refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximin load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain dificulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece diameters to fracture under impact conditions offers considerable experimental difficulty. In order to make it feasible to

Jan 1, 1942

By J. L. Bruce, G. W. Nicolson

ThE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydro-thern~ally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CeMent and Concrete Linings During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, howcver, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 11\2 pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with 12 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concretc and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1949

By R. L. Manegold

This paper outlines the reasons for and the application of suspended magnets above belt conveyors for the purpose of removing tramp iron to protect equipment. The design of a magnet strong enough to extract iron through a distance of 24 in. is described along with the proper method of application in the field. Advantages of the suspended magnet in contrast to the conventional magnetic pulley are also discussed. IN RECENT years there has been a decided trend toward bringing ores and coal out of open-pit and underground mines by long, sloping single-stage belt conveyors. Because the high investment cost of haulage conveyors dictates maximum speed and full loading for economy, conveyor belts are running faster than ever before, with a greater burden on the belts. In addition, larger blocks of ore are being mined and conveyed. Rougher use of large mining equipment generates more tramp iron; mechanical loading rejects nothing. Therefore the extraction of tramp iron and other deleterious materials for the protection of haulage conveyors at transfer points, chutes, and idlers is becoming an increasingly difficult job. In our experience, the best method of protecting long haulage conveyor belts is to extract the tramp iron, at least the large tramp iron, ahead of the main haulage conveyor or series of conveyors. It is most practical to collect the tramp iron at the earliest source possible, usually directly after the primary car unloading dump or after the primary crushers, which are ordinarily not affected by tramp iron, see Fig. 1. The coal or ore from its primary source is fed by chutes or feeders onto a buffer or shock belt conveyor, a short, ruggedly built conveyor system that can be considered somewhat expendable. Its primary function is to bring the ore up to speed for transmission to the haulage conveyor. There is no assured method of protecting this conveyor from tramp iron damage at its feed end. Likewise, there is a possibility, although remote if the magnet applied to this belt is installed correctly, that the tramp iron extraction process will damage the shock belt, which is, however, short and comparatively inexpensive. Magnetic head pulleys with their maximum effective range of about 8 or 10 in. cannot be considered for large installations, even though they are desirable because of the continuous and automatic tramp iron removal feature. Further, the most dangerous form of tramp iron with respect to potential damage to a haulage conveyor is the long rod, roof bolt, or rail segment, which is not extracted satisfactorily because of the limited tangential contact of such an iron shape with the magnet. Magnetic head pulleys are also undesirable because the dribble or fines from the head pulley discharge at the same point as the tramp iron. Screens must be used to separate the fines from the magnetics, resulting in additional expense and loss of head room. Magnetic detectors have been used with success, but they only indicate the presence of iron, and the conveyor belt must be stopped for its manual removal. The stoppage of any conveyor means that all preceding equipment must be stopped or a cascade of material on the idle conveyor will result. Occasionally combinations of detectors and magnetic head pulleys are used. The detector precedes the magnetic head pulley and detects only large pieces of tramp iron, while the magnetic pulley subsequently takes out the smaller ferrous metals. Suspended magnets overcome the disadvantages of magnetic head pulleys, detectors or a combination of both. There are several magnetic extraction problems involved in applying a suspended magnet at this

Jan 1, 1953

By G. S. Hume

During the war years the drilling activity in Canada has been steadily increasing and still further increase is expected in 1945. The production of oil, which in the past has come largely from the Turner Valley field in Alberta, shows a decline since 1942, the peak year. New discoveries made in 1944, however, give promise of replacing the decrease from Turner Valley where the crude-oil production in 1944 was nearly 1,800,000 bbl. less than in 1942, but with an increase of 145,000 bbl. in natural gasoline, a product of great value to the war effort. A very considerable part of the decline in Alberta has been offset by new production of more than a million barrels in 1944 from the Norman Wells field, in the Mackenzie River area of the Northwest Territories. It should not be forgotten, however, that this is largely due to the Canol development, a war project, the future of which is dependent on many factors not connected with an ordinary commercial operation. The year 1944 has been the best in new discoveries in Alberta for all time. The discovery of a new deep field at Jumping-pound, 20 miles west of Calgary, with the hopc of a type of product similar to that of Turner Valley is the culmination of many years of effort to interpret the subsurface structures in relation to the complicated surface foothills faulting and folding. In this case the subsurface structure on the Paleozoic limestone was inferred from geological investigations but precisely defined by seismograph. In addition to Jumpingpound the discovery of oil of 34.5 gravity at a depth of less than 5000 ft, in the Devonian of the Plains at Princess, 125 miles east of Calgary, is of great significance since this is the first substantial production from the Devonian in Alberta, although previously some oil had been obtained at two places from the Devonian in the foothills. The effect of this discovery is already apparent in the number of wells now drilling to the Devonian in the southern Plains. In southern Alberta a new producing area has been found in a Lower Cretaceous sand at Barnwell, a few miles west of Taber. Also, at Conrad, 20 miles southeast of Taber, an important new discovery has been made at a depth of about 3000 ft. in a sand in Jurassic shales, in a strali-graphic trap on the northeast flank of the Sweetgrass arch. In northeast Central Alberta an important extension has been found in the Lloydminster area, where only a few wells have so far been drilled. A new well 3 1/2 miles south of the previous producers found a coarser sand at the productive horizon and as a result will have an increased daily yield. At Blackfoot, 9 miles west of Lloydrninster, a new producing area in the Lower Cretaceous may have been discovered at a depth of 2004 ft. At the end of 1944 the well was being tested. Forty-four unsuccessful wildcat wells were drilled in Alberta in 1944. The decline of Turner Valley, the major producing field, was anticipated at the beginning of the war and in an effort to offset this and encourage new development the Dominion Government put into force tax concessions and other measures that,

Jan 1, 1945

By H. B. Heller, T. J. LaChapelle

Phosphorus nitride has been used as a diffusant for introducing phosphorus into silicon under various conditions. It has a temperature -dependent rate of decomposition beginning in the 500°C range, increasing very rapidly above 1000 C, producing gas -eous phosphorus and nitrogen. Best control was obtained with a two-temperature arrangement, with silicon at the proper higher diffusion temperature. It is an easier compound to use than the usual P2O5 because it is nonhygroscopic and yields temperature-controlled surface concentrations together with excellent final surfaces. Surface doping nearly as high as that produced by phosphorus pentoxide has been observed for sources at 850" to 900°C. Reproducible high sheet resistances were obtained by using slow flow rates (1 linear in. per min) and staggered-baffle gas mixing with the nitride at 550°C. Both inert gas (argon, nitrogen) and oxidizing ambients have been examined. Oxygen reacts to produce anhydrous P2O5, consuming the source at a rapid rate. Nitrogen, except for short diffusion times, suppressed the dissociation reaction and sometimes produced inferior surfaces. Argon appears to be a more useful ambient. PHOSPHORUS is a common impurity atom which may be introduced into a semiconductor lattice to create a p-n junction or an nn contact region. Various investigators1-4 have described techniques which can be used with either elemental phosphorus or certain of its compounds. This paper discusses a newly available compound of phosphorus, phos- some processes silicon wafers are precoated with a phosphate glass which acts as the doping source. Although a nonoxidizing form like elemental phosphorus or a phosphine can be used, most diffusion methods usually involve the use of phosphorus pentoxide. Because of the rapid volatility of this compound, a two-step process is often used, combining a gaseous deposition to introduce a predetermined quantity of phosphorus into the silicon with a later redistribution to obtain the desired distribution and surface concentration. Such a process usually involves predepositing phosphorus at surface concentrations greater than 1020 cm-&apos;. At such doping levels the phosphorus-diffusion coefficient appears to be strongly concentration-dependent.596 Distribution profiles5&apos;9 for these high concentrations of phosphorus do not follow Fick&apos;s laws, having extended subsurface regions which appear electrically to be nearly uniformly doped with ionized impurity atoms. Radioactive-tracer experiments also show near-surface anomalies in the distribution profile. Additionally, it has been shown1&apos; that the introduction of very high surface concentrations of impurity atoms into silicon (a step necessitated by the subsequent lowering of concentration during the redistribution) creates dislocations, even in material having no dislocations originally. For device fabrication the use of oxide masking introduces certain difficulties and limitations.7&apos;8 The standard practice of using phosphorus pentoxide as an impurity source adds other problems to these because of the speed and ease with which this compound reacts with moisture present in any gas in contact with it. In fact, P2O5 is one of the fastest and most effective drying agents for gases. Because it is such an excellent desiccant, completely anhydrous phosphorus pentoxide is difficult to obtain and is even more difficult to keep dry. Adequately dry gloved boxes must be used for storage and transfer of the chemical. The presence of even traces of moisture will cause formation of phosphoric acids which, during the high-temperature diffusion, results in polyphosphoric acids of variable composition. Such reaction by-products end up as gradually accumulating viscous fluids in the cooler parts of the diffusion furnace. The calculation of the final solute distribution for

Jan 1, 1964

By R. L. Manegold

This paper outlines the reasons for and the application of suspended magnets above belt conveyors for the purpose of removing tramp iron to protect equipment. The design of a magnet strong enough to extract iron through a distance of 24 in. is described along with the proper method of application in the field. Advantages of the suspended magnet in contrast to the conventional magnetic pulley are also discussed. IN RECENT years there has been a decided trend toward bringing ores and coal out of open-pit and underground mines by long, sloping single-stage belt conveyors. Because the high investment cost of haulage conveyors dictates maximum speed and full loading for economy, conveyor belts are running faster than ever before, with a greater burden on the belts. In addition, larger blocks of ore are being mined and conveyed. Rougher use of large mining equipment generates more tramp iron; mechanical loading rejects nothing. Therefore the extraction of tramp iron and other deleterious materials for the protection of haulage conveyors at transfer points, chutes, and idlers is becoming an increasingly difficult job. In our experience, the best method of protecting long haulage conveyor belts is to extract the tramp iron, at least the large tramp iron, ahead of the main haulage conveyor or series of conveyors. It is most practical to collect the tramp iron at the earliest source possible, usually directly after the primary car unloading dump or after the primary crushers, which are ordinarily not affected by tramp iron, see Fig. 1. The coal or ore from its primary source is fed by chutes or feeders onto a buffer or shock belt conveyor, a short, ruggedly built conveyor system that can be considered somewhat expendable. Its primary function is to bring the ore up to speed for transmission to the haulage conveyor. There is no assured method of protecting this conveyor from tramp iron damage at its feed end. Likewise, there is a possibility, although remote if the magnet applied to this belt is installed correctly, that the tramp iron extraction process will damage the shock belt, which is, however, short and comparatively inexpensive. Magnetic head pulleys with their maximum effective range of about 8 or 10 in. cannot be considered for large installations, even though they are desirable because of the continuous and automatic tramp iron removal feature. Further, the most dangerous form of tramp iron with respect to potential damage to a haulage conveyor is the long rod, roof bolt, or rail segment, which is not extracted satisfactorily because of the limited tangential contact of such an iron shape with the magnet. Magnetic head pulleys are also undesirable because the dribble or fines from the head pulley discharge at the same point as the tramp iron. Screens must be used to separate the fines from the magnetics, resulting in additional expense and loss of head room. Magnetic detectors have been used with success, but they only indicate the presence of iron, and the conveyor belt must be stopped for its manual removal. The stoppage of any conveyor means that all preceding equipment must be stopped or a cascade of material on the idle conveyor will result. Occasionally combinations of detectors and magnetic head pulleys are used. The detector precedes the magnetic head pulley and detects only large pieces of tramp iron, while the magnetic pulley subsequently takes out the smaller ferrous metals. Suspended magnets overcome the disadvantages of magnetic head pulleys, detectors or a combination of both. There are several magnetic extraction problems involved in applying a suspended magnet at this

Jan 1, 1953

By C. Perez-Rosales

A simplified method for evaluating specific surface of porous media is described. The theory takes as its point of departure a previous statistical method. Due to its simplicity, it is considered that the proposed method has certain advantages over methods currently used. By making some simplifications, the procedure for estimating specific surface is reduced to superposing, on an enlarged reproduction of a section of the sample to be analyzed, an evenly spaced grid and counting the number of intersections of the grid lines with the perimeter of pores. An indirect test of the theory is presented and the advantages of the method are discussed. INTRODUCTION The specific surface of a porous medium, defined as the surface area of the pores per unit bulk volume, is an important parameter with regard to flow of fluids through porous materials. In particular, it has long been recognized that specific surface is closely related to permeability. Since the internal surface of any porous material is extremely complex, the measurement of specific surface can only be accomplished by indirect means. It is considered that the best method&apos; in current use for determining specific surface is the statistical method of Chalkley, Cornfield and Parka who originally applied it for estimating volume-surface ratios of morphologic components, such as cells or nuclei. This method will be outlined later. A method which has been used extensively in determining specific surface is based on the adsorption of a vapor by the internal surface of porous media. However, this method does not yield the surface pertinent to fluid flow, since it includes the tiny molecular interstices which do not influence the permeability of the porous material.&apos; This method has been employed by Brooks and Purcell measure internal surface area of sedimentary rocks. The Kozeny equation, which relates the specific surface to the permeability of a porous medium, has found wide use in determination of specific surface. However, the KOzeny equation is not strictly correct. Large discrepancies have been found between theory and experiments.&apos; Consequently. the specific surface estimated by this method is subject to serious uncertainties. Finally, there are other methods for specific surface measurements which are based upon a variety of physical and chemical properties: the heat conduction by a gas, ionic adsorption phenomena and direct chemical reactions of the surface with other substances. This paper describes a simplified statistical method for determining specific surface of porous materials. It is considered that, due to its simplicity, it has certain advantages over the methods presently used. For its validity, it is required that the porous structure of the material under study be of a spatially random nature. This is not a serious limitation since the naturally occurring porous media have this characteristic. THEORY The method proposed in this paper takes as its point of departure the interesting result obtained by Chalkley et al The method shows that if a line of length r is dropped repeatedly at random over a section of a porous medium, and counts are made of the number of times the two end points fall within pore areas (denoted by h for "hits") and the number of times the line intersects the perimeter of pores (denoted by c for "cuts"), then in a very large number of throws where S is the internal surface of the sample (surface of pores) and V, the volume of the pores (Fig. 1). Since the specific surface S, and the porosity 4 are given, respectively, by S. = Sl V, and 4 = V,l V,, where V, is the total volume of the sample, it follows from Eq. 1

By J. R. Hornaday, A. E. Morris, N. A. Parlee, D. C. Carmichael

Rates of absorption and effusion of hydrogen in solid iron were measurede by a Sieverts type of apparatus. With clean a iron these rates are diffusion controlled down to 420°C and are represented by the equation D = 6.70 x e-&apos;100&apos; crn2 sec-I Certain surface impurities can affect these rates at all temper-atuves. Thin oxide films lower, the apparent diffusivity of annealed iron markedly. Cold-worked iron (75 pct) annealed at 430°C has practically the same solubility and diffusivity as anealed iron. THE mechanism of absorption and evolution of hydrogen in solid iron alloys is not fully understood despite the large number of investigations on the subject. While there appear to be many instances of simple solid-state diffusion control of rate, there are many cases where investigators have either concluded that surface reactions are rate controlling or that some "nondiffusible" hydrogen resides in discontinuities. The purposes of this research were 1) to develop a sound method for studying this absorption and evolution behavior, 2) to examine it in pure annealed iron, and 3) to determine the effects of important variables, such as cold work, surface condition, and composition. This paper relates the progress toward these objectives. Much of the present knowledge of the movement of hydrogen through iron alloys comes from permeability studies which involve the measurement of the rate of passage (under steady state conditions) through membranes of the order of 1 mm in thickness. This method is open to question on various grounds. If surface reactions are involved, two different surfaces operating under two different conditions must be considered. The presence of defects in the membrane even of microscopic dimensions may lead to erroneous results. A few people have studied evolution of hydrogen into vacuum, under carefully controlled (unsteady state) conditions, and some of the best diffusivity data come from these sources. Most of these methods measure rates of evolution only and thus do not make a rigorous test for reversibility of behavior. It appeared that an "unsteady state" method that would permit the measurement of both rates of evolution and absorption under controlled temperature, pressure, and other conditions would offer several advantages. Accordingly the modified Sieverts apparatus described below was designed and built. APPARATUS This apparatus is shown in Fig. 1. The sample bulb is detailed in Fig. 2. Hydrogen of 99.5 pct purity and argon of 99.99 pct purity were used. The hydrogen was deoxidized and dried by means of a Deoxo unit followed by a "Dri-erite" tower. The argon was only dried. The gas burette was graduated in tenths of a cubic centimeter, and, with the aid of a travelling magnifier, readings could be estimated to the nearest 0.01 cc. The level of mercury in the burette was adjusted by means of a leveling bulb operated by a fine screw adjustment. An electrical system, consisting of two slightly separated platinum electrodes inserted in one leg of the manometer and a small light bulb was used to obtain rapid accurate adjustment of the pressure. The capillary tubing of the Vycor sample bulb was 3 mm bore as was all tubing back to the gas burette. The samples were discs made from vacuum-melted Ferrovac-E iron of greater than

Jan 1, 1961