Search Documents

By Stanley C. Herold

A few hates on the occurrence and significance of mud volcanoes in Colombia may be of interest at the present time, owing to the renewed activity in geological exploration of the coastal regions bordering the Caribbean Sea. The best-known volcanoes are found a few miles from the seacoast. One is situated to the south of Puerto Colombia; the second, to the east of Cartagena near the village of Turbaco; and the third, near the village of Puerto Escondido south of the Sinu River. Others are reported in more inaccessible localities. Usually they stand 2 1/2 or 3 ft. (0.762 or 0.914 m.) above the surrounding ground at the crater, though several craters from 10 to 20 ft. -(3.04 to 6.09 m.) "apart will often build up an extensive mound at low gradient. The shallow mound may cover 1/2 or 3/4 acre (0.2 to 0.3 ha.) with an elevation of 12 or 15 ft. (3.65 or 4.57 m.) at the, center. The craters are formed of hardened blue clay; the inside diameters vary from 14 to 24 in. (35.56 to 60.96 cm.). The rim is continuous, except on one side where there is usually a cut 3 or 4 in. deep, thus allowing an overflow. The craters are filled to the' rim-cut with a thick mixture of blue clay mud and water, which is kept in agitation by escaping gas. Fig. 1 shows the bubble in the act of bursting and Fig. 2 the appearance of the surface of the viscous fluid a second or so later. The frequency of the explosions is determined by the weight of the column of fluid in the neck of the volcano, consequently, such explosions are not synchronous in a group of craters. Ordinarily, there arc two or three explosions in about 3 minutes. The supply of gas is small but steady and sufficient pressure must accumulate before the bubble can enter the column of fluid. The water is derived from the surface and enters the scdirnentary strata not far distant from the volcano. During long dry seasons, as the supply of water fails the volcano dries and geyser action ceases. The temperature of the muddy fluid is normal; the gas is dry and inflammable. - No petroleum products come with the gas. On the surface of the fluid, there is sometimes a dark brown streaky scum, which

Jan 1, 1920

By H. W. Camp

RESEARCH is defined, scientifically, as a "sys- tematic investigation of some phenomenon, and also a search for hidden treasures." Chemists tell us that the hidden treasures of petroleum are far richer than the .products which have been best known to us. However, these secrets will be discovered only through intensive and systematic, as well as scientific, industrial research. Indeed, the scope of the subject is so great that such an intensive research program should be assumed by a centralized organization supported by the petroleum industry as a whole. Such organization would assume the responsibilities for investigation of new products and development of markets for such products. Gasoline, the chief product of the petroleum industry, has become a cheap commodity. The continual un-controlled overproduction of crude petroleum, the in-tensive competitive condition in the marketing of petro-leum products and the increase of refining efficiency and installing of cracking facilities, have all combined to lower the market value of gasoline. The lower cost of gasoline has all been passed on to the purchaser in the form of lower prices so that today the most important product can scarcely be manufactured at a profit. In other fields, manufacturing industries have diversified their products when faced by a similar situation. Thus, they have been able to widen their marketing outlook. Why cannot the petroleum industry employ the same tactics ? Right now we are hearing much discussion concerning the development of a wider market for existing petro-leum products and new products for existing or prospec-tive markets. For instance, we can cite recent develop-ments for use of propane, butane, and ethylene. Butane has been found to be an efficient and inexpensive re-frigerant, especially adapted to home refrigerating sys-tems. Propane and butane fractions of natural gasoline may be shipped under pressure and may be used as a substitute for acetylene in cutting torches in connection with oxygen. There is a possibility of substituting butane for gas oil in the carbureting of coal gas, as we know that butane contains practically the gas enrich-ment as the same volume of gas oil and should prove to be a superior product for this function. Ethylene, a hydrocarbon present in cracked gases, is finding an outlet for the artificial ripening of green fruits. The following table . shows the more general use of petro-leum products as now established.

Jan 4, 1928

W. E. WRATHER, Wichita Falls, Tex. (written discussion*).-The appearance of Mr. Brokaw?s with-the chemical composition of "paraffin dirt" will be welcomed by oil geologists who have worked in the Gulf Coast district. It is to be hoped that it will lead to a discussion of the subject which will throw some light on the relation this peculiar substance bears to the occurrence of oil deposits. The problem of locating oil pools in advance of drilling is at the best a very intangible matter in the district along the Gulf Coast, and it is therefore desirable to make the most of any clew which may be of the least assistance to this end. Geologists have been familiar with "paraffin dirt" for a number of years, and have informally discussed its value as a surface indication of oil. But doubtless owing largely to the fact that they have been unable to define its exact composition, very little information has appeared in print on the subject. The presence of this baffling and somewhat indeterminate substance is now quite generally accepted as one of the most reliable indications of a gas seepage. The question is whether paraffin dirt necessarily indicates that the escaping gas is an emanation from an oil deposit, or whether it merely indicates that marsh gas (urethane) has here escaped from its source in "the abundant decomposing vegetation entombed in the sediments of the old Mississippi Embayment, and the Gulf Coastal Plain. The presence of this material has been relied upon to a great extent, both by oil producers and geologists, in the location of wildcat wells, since the discovery that it was associated with gas seepages. It is quite true that other surface indications were often present at such localities, but if, in addition, paraffin dirt could be found in the vicinity, this fact was accepted as the final justification for drilling a test well, despite the fact that no one seemed to understand its chemical composition or to know why it should be associated with oil. In fact, for a long time it has generally been accepted that the name is a misnomer, that very little, if any, paraffin is present in it, or, for that matter, any other known fraction of crude oil.

Jan 7, 1918

FOLLOWING the presentation at the annual meet-ing of the paper "Recent Developments in Classi-fication," by A. M. Gaudin and W. L. Remick, the discussion presented below took place: H. N. Spicer : I haven't been able to study this paper closely, but I would like to ask 'Mr. Remick something regarding the work done by the mechanical classifier. The screen test given here would appear to show that the classi-fier did very, very poor work. The 44 per cent efficiency calculated from this equation is much lower than any ordinary operation. Nothing is stated regarding the de-tails. of the operation, the slope of the classifier, the dilu-tion, the speed, and such other factors that influence results. I would also like to know something of the material that was worked. The Manhattan schist that I have seen them digging out of the subways is of a flaky nature, so that in any classifier, you might get the factor of fine flakes floating over. Was the same material used in the hydrotator test? The screen tests vary a whole lot. Mr. Remick: You will notice the Dorr classifier han-dled the circulating load. This classifier naturally was run in closed circuit. I should like to be pardoned for quoting from Mr. Bates' paper of last year on "Classifica-tion in the Witwatersrand Mills." In this report only two efficiencies were given for the so-called straight type Dorr classifier. One was 44.6 per cent and the other 61.6. I don't know whether or not an average should be taken for the proper performance. I assume that that test was performed under better conditions, yet the efficiencies av-eraged only 53.1 per cent. I am afraid I am taking the words out of Professor Taggart's mouth, but he has told me that the Dorr classi-fier at Columbia is not the proper size to work with the Hardinge mill with which it is connected. This indicates only the inadvisability of putting commercial sized mat chines in a school laboratory. You cannot, he says, get the proper tonnage from the Hardinge mill to work the Dorr classifier and get the best results. Mr. Bates' results show higher efficiency with the lower capacity. Now, on the other hand, I assume that the classifier described in Mr. Bates' paper was probably run at the proper capacity.. It is a rather puzzling question.

Jan 4, 1927

By W. Irwin Moyer

Two methods for the rapid valuation of oil properties are in common use. The one best known and most widely used is the "per barrel" value, based on the present daily production of the well, without regard to its past performance or the history of the sand or pool from which it produces. The second method is the "time to pay out," or the length of time required for a well to place itself upon the credit side of the ledger, from which time the returns from its production (less the operating expenses) will be clear profit. The time basis for valuation is also commonly used in the appraisal of an undeveloped lease. In most oil fields, it is not thought good business to invest in production that will not pay out in at least 4 to 5 years. Nearly all buyers (except in certain regions of very persistent production like the deep-sand territory of the Appalachian field) expect wells to pay out in considerably less time than this. Like the barrel per day price, the time necessary for a well to pay out has been determined for each field, so that one frequently hears a field or district referred to as having a certain time to pay out. This is considered the norm for that field or district and the buyer and seller base their value, to greater or less extent, on their belief in the accuracy of this time. The writer long ago became convinced of the inaccuracy of the barrel per day method, except when greatly modified for local conditions, such as the age of the wells, their economic limit, operating conditions in the field, the future price of oil, and the persistence of the sand as a producer. When so modified, this method becomes more of an analytic or predicted probable yield valuation. While the appraiser may not go through each step in a valuation based on future returnable revenue, his knowledge of the field and the local conditions surrounding his leases make it possible for him to estimate a fair sales value that, in many cases, will be a close approximation to the truth. This is quite different from the commonly understood barrel per day value, in that the conditions surrounding the sale of one lease or property at a fair market value may

Jan 1, 1922

Discussion of the paper of E. C. HARDER, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2573 to 2586. I. C. WHITE, Morgantown, W. Va.-I have seen some of the great iron-ore deposits described in this paper. -One of these in the State of Minas Geraes appears to be an immense mountain of iron ore about 2,000 ft. in height. All over its surface from bottom to top may be seen large masses of rich iron ore, varying in weight from a few pounds to several tons, and from all that one can judge without exploitation, the quantity of available ore is certainly very large in this particular mountain. Whether it will prove a mere surface deposit or shell, like the famous Iron Mountain of Missouri, is for future exploration to determine. The question of transportation is the main factor in determining the availability for exportation of these Brazilian iron ores. There is no coal in Brazil that can be manufactured into coke without expensive previous treatment, since the best of the raw coal in the States of Rio Grande do Sul, Santa Catharina, and Parana, contains about 35 per cent. of ash, of which about 6 per cent. is sulphur, and coal of this composition cannot be utilized in iron smelting without purification. When I was chief of the Brazilian Coal Commission in 1904 to 1906, I had a cargo of this coal shipped to Balk, Germany, and treated in the great coal-testing plant of the Humboldt Engineering Works, located just across the Rhine from Cologne. It was found that by crushing and washing the Brazilian coal, it yielded 33 per cent. of briquetting coal, containing only 10 to 12 per cent. of ash (of which 1 per cent. was sulphur), and 42 per cent. of slack coal, with 25 per cent. of ash and low in sulphur, so that about 33 per cent. of the Brazilian coal could be converted into coke of fair quality, as shown by the following average of three analyses, using air-dried coal, of briquets made from the Barro Branco coal bed, State of Santa Catharina: Moisture 1.56 Volatile matter 31.66 Fixed carbon 56.73 Ash : 10.05 Total 100.00 Sulphur 1.34 Phosphorus 0.003 B.t.u 13,395

Jan 4, 1915

By H. F. Seifert

The classification and preparation of non-ferrous scrap mctals is a subject of interest to every individual and corporation that employs in its processes of manufacture non-ferrous metals and alloys and accurnulates in such manufacture scrap from these materials for disposition in the form of turnings, borings, short ends, punchings, clippings, grindings, washings, etc. All too frequently the disposition of such scrap is left to indivitluals who have no knowledge of the subject either from a metallurgical or a commercial standpoint, or both. Much money is thus lost whicli with a little more intelligent effort might be saved, and in this day of fierce competition and small profits such an opportunity cannot be ignored. The Mineral Resources of the United States for the year 1925, the latest issue available (Part 1, page 221), gives the secondary non-ferrous metals of certain classes recovered in the United States for the year 1924 to 1925 as shown in Table 1. The figures are tabulated simply to give the reader some idea of the scope of the secondary non-ferrous metal industry. Approximately 900,000 tons of an annual value of $244,000,000 were recovered in the year cited. In 1916 (again using thc Mineral Resources of the United States as authority) the tonnage reclaimed was approximately 632,000 tons and the value, because of the high prices for metals prevailing at that time, amounted to $265,000,000. It is not the purpose of this paper to discuss smelting and refining operations or the feasibility of an organization, primarily engaged in some other activity, conducting smelting and refining operations to convert its own non-ferrous scrap metals and alloys. The classification and preparation of these non-ferrous materials is a preliminary step, regardless of what subsequent operations the material may pass through or where these operations may be conducted. For that reason the subject can he readily discussed without any reference to subsequent activities. Space must be provided, with suitable handling facilities, scales and the necessary storage bins where the material may be accumulated. The scope of the activity, the nature of the industry and the tonnage handled will determine, in a large measure, what preparation, if any, it rrlay he desirable to give these scrap materials to put them in the best niarketable condition. By preparation is rneant largely what, for the want of a

By W. Irwin Moyer

Two methods for the rapid valuation of oil properties are in common use. The one best known and most widely used is the "per barrel" value, based on the present daily production of the well, without regard to its past performance or the history of the sand or pool from which it produces. The second method is the "time to pay out," or the lengt of time required for a well to place itself upon the credit side of the ledger, from which time the returns from its production (less the operating expenses) will be clear profit. The time basis for valuation is also commonly used in the appraisal of an undeveloped lease. In most oil fields, it is not thought good business to invest in production that will not pay out in at least 4 to 5 years. Nearly all buyers (except in certain regions of very persistent production like the deep-sand territory of the Appalachian field) expect wells to pay out in considerably less time than this. Like the barrel-per-day price, the time necessary for a well to pay out has been determined for each field, so that one frequently hears a field or district referred to as having a certain time to pay out. This is considered the norm for that field or district and the buyer and seller base their value, to greater or less extent, on their belief in the accuracy of this time. The writer long ago became convinced of the inaccuracy of the barrel-per-day method, except when greatly modified for local conditions, such as the age of the wells, their economic limit, operating conditions in the field, the future price of oil, and the persistence of the sand as a producer. When so modified, this method becomes more of an analytic or predicted probable-yield valuation. While the appraiser may not go through each step in a valuation based on future returnable revenue, his knowledge of the field and the local conditions surrounding his leases make it possible for him to estimate a fair sales value that, in many cases, will be a close approximation to the truth. This is quite different from she commonly understood barrel-per-day value, in that the conditions turrounding the sale of one lease or property at a fair market value may

Jan 1, 1923

By S. E. Bretherton

MOST metallurgists appreciate the great need of a process for the extraction and recovery of valuable metals from complex ore, where the presence of one metal increases the cost of extracting the other metals to such an extent that not any of the metals can be extracted at a profit. We need only refer to some of the mines in Colorado, Utah, and New Mexico, where oxidation has taken place and the sulphur, zinc, copper, and some of the iron and other metals have been leached out, large bodies of oxidized ore remaining, rich in lead, silver, and sometimes gold. These metals have been concentrated by the removal of the other metals, leaving a very desirable ore for treatment in the blast-furnace for the production of lead bullion, and recovery of the silver and gold. If lead is not present, the gold and silver are usually recovered by some method of milling, or the ore is shipped to a smelter, where it is mixed with lead ore or copper-iron sulphide ore from some other mine. In these same mines, when developed to greater depth below the leached or oxidized zone, the ore is found to contain the original mixture of sulphur, zinc, copper, etc., added to, or I should say left with, the lead, silver, and gold values; but instead of adding to the value of the ore, the presence of these elements, especially zinc, makes the copper, silver, and gold of less value, and often worthless. Such was the experience of the oldest mines in Leadville, Colo., until methods of mechanical separation of the lead from the zinc were developed sufficiently to allow of some profit by the making of a concentrate rich in zinc to be shipped to the zinc smelter, and sometimes a lead concentrate which could be shipped to the lead smelter; but even in these cases the waste of the different metals is a very serious matter. In the very best concentrating plants some zinc will be left in the lead concentrate, to be lost and to give considerable trouble in the lead-smelting furnace. On the other hand, some of the lead, with a large percentage of the copper and silver, will follow the zinc into the zinc concentrate, to be, perhaps, recovered y smelting the cinder or clinker left in the re-

Jan 7, 1914

By Raymond B. Ladoo

TIIe milling of talc, as is the case with many non-metallic minerals, until recently, has not received adequate technical consideration, for the talc industry has become of importance only within the last decade. At first, talc was used only in the massive form, for foot warmers, griddles, and so on, and milling methods were unnecessary. As the demand for ground talc increased, producers adopted the machinery used in the milling of flour; in fact, many talc mills were rebuilt flour mills. Improvement has been slow, but today several types of grinding and separating machinery are in use; many of them, however, are still inadequate and inefficient. To determine the best methods of milling talc, it is necessary to understand the essential properties a talc must possess to fit it for a particular use. For toilet purposes, whiteness, freedom from lime and grit, fineness of grain, and good "slip" are essential. As a paper filler or coating, the talc must be white, uniform, and fine grained, have a good slip, and be free from grit and iron; freedom from lime is a disputed point. Fibrous talc is supposed to be superior to massive on account of the interlocking of grains in the paper, thus increasing its strength; this point, though, is in doubt. In general, talc for the paper industry need not be of as high quality or as fine grained as that used for toilet purposes. Talc is usually bought by sample, for which reason it is difficult to state the essential properties for use in paint, rubber, roofing, and so on. The adoption of standard screen tests and standard grades by producers is necessary before an accurate basis for manufacturing or selling standards can be established. Off-color talcs might be utilized, as in Germany and Austria, by the establishment of standard grades of colored talcs. The machinery to be used depends on whether the talc is fibrous, foliated, or massive; hard or soft; of uniform or variable grade; pure or impure. In some cases, it is possible to change the mining practice or to utilize different sections of the deposit in order to vary some of these factors, but in many cases these factors are fixed, so the milling must be designed to suit the conditions.

Jan 1, 1922

Discussion of the paper of George C. Stone, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2401 to 2402. D. S. JACOBUS,* New York, N. Y.:-The engineers of the country are waking up to the possibilities of waste-heat boilers. As the cost of fuel increases, and as more attention is given to economies, it is evident that a great deal may lie gained by utilizing heat that has ordinarily been wasted. The art in the manufacture of' waste-heat boilers has. advanced so that it will now pay to install them under certain conditions where it would not have paid to install boilers constructed in accordance with older methods. In using boilers where the gases are at a comparatively low temperature, a great deal depends on the method of baffling the boiler in securing good results. The Babcock & Wilcox Co. has made a careful investigation of the laws of heat transfer and has applied the same to waste-heat boilers, which have been carefully tested under operating conditions, with the result that we now know what to expect with different arrangements of baffles and heating surfaces. The old idea of installing waste-heat boilers was to provide an arrangement where the draft loss would be a minimum, and little or no attention was paid to the effect of different systems of baffling on the steaming capacity of the boiler. In some instances, to secure a minimum draft loss no baffles were placed in the boilers. After making a most careful study of the subject it developed that this practice was bad, and that to obtain the best commercial economy, in place of endeavoring to obtain a minimum draft loss, an arrangement should be used that would lead to the maximum amount of heat transmission with a comparatively high draft loss. In nearly every case the amount of resistance of the gases fussing through the boiler involves the use of an induced-draft ,fan, but the additional capacity developed by the boiler over that which could be secured with the older designs, through arranging the heating surface properly and using proper baffles, much more than pays for the increase in the steam required to drive the fan.

Jan 12, 1913

By Burton Atkinson, David Johnston

Evaluation of Ellenburger reservoirs in West Texas has been an uncertain matker at best because of the lack of cores and suitable core-analysis method. Large amounts of oil arc produced from sections from which sample cuttings are obtained that contain litile porosity and no oil saturation. It has long been realized that the formation in some areas contained numerous fractures and solulion cavities that probably contained the major part of the oil present but the magnitude of the porous system conltaining oil has been unknown. Diamond coring cquipmene, used in the mining industry lor many years, has been developed for oil-field use to obtain high core recovery in fractured dolomite that is not possible with conventional coring equipment. A 36ft section of the core recovered from a fractured Ellenburger reseivoir waS analyzed by a unique but simple method to obtain the first defmite evaluation of one section of the producing formation. The cores and the method of analysis used are described and the results arc discussed in some detail. Discussion The first successful known analyses of cores recovered from the Ellenburger formation in the Permian Basin area were made on cores recovered with the use of diamond core heads. Conventionul coring methods previously used have had lour core recovery and standard methods of analysis have proved to be inadequate for evaluation of those cores that were recovered. Core Descriplion The Ellenburger formation to be dis cussed was cored using diamond core heads and oil-base drilling fluid. Of the total 103 ft cored to a depth of 8893 ft in the Ellenburger, 99 ft or 96 pct was recovered. The dolomite cores were described as gray to white, crystalline to coarscIy crystalline, with chert and calcite inclusions. Occasional shale partings ? to ¼ in. in width were noted. A small amount of green clay was found in some of the coarsely crystalline material. So intergranular porosity was found by inspection in any of the cores. The core urns highly fractured over most of its length with not more than two continuous feet that failed to contain fractures. The fractures Were nearly vertical and varied in width from those harely visible to as much as one millimeter. Scattered solution voids, or vugs, as large as 3 cm in diameter occurred in association with same •a

Jan 1, 1949

By J. M. Lommel

DURING an investigation into the effect of heat-treatment on the creep properties of the magnesium alloy ZW1, (1 pct Zn, 0.6 pct Zr), the previously published methods of final polishing were found to be unsatisfactory. A new diamond-polishing technique has been developed to facilitate the study of fine precipitates in this and other magnesium alloys, and is described in this note. The sectioning and coarse grinding techniques are those of Fox and Hall,' and Hess and Cieorge.' Pre- liminary mechanical polishing is done with 6-µ, and 1-µ( grades of diamond compound on 'Microcloth' using a lubricant of 'Hyprez' oil. When the conventional technique is used with a 1/4- µ diamond wheel for the final polishing of magnesium alloys, scratching is likely to result from the abrasive action of the 'Microcloth' nap on the soft metal surface. This problem has been overcome by the use of a cream on the wheel in order to separate the specimen surface from the polishing cloth. To prepare this cream, a solution of 6-ml tri-ethanolamine in 75-ml water is stirred into 12.5 g stearic acid at a constant temperature of 80o to 90°C. The cream is allowed to cool, and is then 'whipped' to a smooth consistency with 100-ml 'Hyprez' oil. Before polishing, the diamond loaded 'Microcloth' is moistened with a few drops of 'Hyprez' oil, then a small amount of cream is worked into the nap. For the best results a wheel speed of 500 rpm should be used for polishing, and the specimen should be held by hand with a light pressure while being rotated in the opposite direction to the wheel. After polishing it is necessary to swab the specimen thoroughly in methylated spirits to remove residual cream and oil from the surface in order to avoid uneven etching and drying stains. Fig. 1 shows the surface finish obtained on a specimen by polishing on a 1/4- µ diamond wheel using the cream, and Figs. 2 and 3 the precipitate observed in ZW1 after polishing, and etching for two seconds in nitric acid 15 pct in ethylene glycol. This new diamond-polishing technique has made a valuable contribution to the programme of metal-lographic research on ZW1 and has become a routine laboratory practice for other low alloy content magnesium alloys.

Jan 1, 1961

By S. Fisher Morris

The New River coal-field embraces that portion of the Appalachian coal formation which lies on the waters of the New River, principally in Fayette and Raleigh counties, West Virginia, covering a strip of territory about forty miles in length along the line of the Chesapeake and Ohio Railroad from Quinnimont to Kanawha Falls, where the New River empties into the Kanawha, the railroad following the banks of the river the whole distance. (See map.) Between Kanawha Falls and the Valley of the Ohio lies the great Kanawha region, and these two coal-fields possess a greater variety of coal than can be found in any other portion of the country, enabling them to furnish the best fuels for any of the various demands of manufacture or domestic use, the Kanawha region possessing many varieties of gas, hard splint, and cannel coal, and the New River region bituminous and semi-bitnminous, steam and coking coal. The New River, in its westward course towards the Kanawha, has cut its way entirely through the Sera1 conglomerate or No. XII of the Pennsylvania Reports, the Umbral red shales of No. XI appearing at the foot of the mountains at the eastern end of the region at Quinnimont, one of the upper ledges of the Conglomerate forming the summits; while at the western end, at Kanawha Falls, the top of the Conglomerate is nearly down to the level of the river, a portion of the " Lower Productive Measures" forming the greater portion of the mountains. These mountains rise abruptly from the banks of the river to a height of from 800 to 1200 feet, leaving only here and there narrow strips of bottom land, a few acres in extent; and as the measures consist principally of hard sandstones, shales, and conglomerates lying ill a nearly horizontal position, the mountain-sides are very precipitous, with many long and high cliffs, which, with the great height of the mountains, give the country a very rugged appearance. Along the sides of these mountains fronting on the New River and its many tributaries there are exposed the outcroppings of several veins of bituminous and. semi-bituminous coal, varying in thickness from a few inches to over four feet, five of them being workable, or

Jan 1, 1880

The officers and staff of the Petroleum Division are the servants of the members, and to the extent that the wishes of the members are made known and are practicable they will be carried out. The tentative plans outlined here are in general accord with previous custom, but modified by suggestions received recently from various members. The advice of all members is solicited, and it is hoped that the general expression on matters of policy can soon be facilitated by circulation of a questionnaire. Plans for two mid-year meetings of the Petroleum Division and for participation in the annual meeting at New York were inaugurated at the last annual meeting and are being carried forward as rapidly as possible in the belief that an early start will increase the possibility of finding the best available program material and permit the careful preparation, review, editing, and advance discussion of papers. While a number of papers have already been solicited, both members and nonmembers are hereby invited to submit additional papers, with the assurance that such papers will be given just as favorable consideration as the papers that have been requested. Mid-year meetings will be held at about the same time both in the Mid-Continent and California. The time will be selected if possible to coincide with the visits of President Lovejoy, who expects to be in California the last of September and in Texas early in October. Fort Worth, Dallas and Austin have been suggested for the Mid-Continent meeting. The Pacific Coast meeting will be held at Los Angeles. It is to be noted particularly that a Pacific Coast meeting was waived last year in favor of the annual meeting of the American Petroleum Institute, which was held at Los Angeles for the first time in nine years. It is hoped, and it was the understanding at the time among a number of individuals interested in both organizations, that in view of this action of the Petroleum Division the industry will give more than the usual support to the A.I.M.E. meeting this year. Ultimate Recovery is being considered as the keynote topic for the mid-year meetings. In view of trying financial conditions combined with an exceptionally high current potential rate of production, it is natural that the attention of the industry should be focused upon means of controlling production and reducing cost of operation. It seems that the Petroleum Division of the A.I.M.E., as a professional group, might

Jan 1, 1936

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given below. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers. Robert W. Hunt Medal and Prize THE partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes: first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the subcommittee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A subcommittee of three to five, including the Chairman of the Iron and Steel Division, shall be appointed by the Iron and Steel Division annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of .the Institute. 5. The recipient of the award shall be designated "The Hunt Medalist." Awards of the medal have been made as follows: 1920—-Robert Woolston Hunt. 192G—John A. Mathews. 1926—Charles Lewis Kinney, Jr. 1929—Edgar Collins Bain. 193G—James Aston. Awards of the prize have been made as follows: 1928—C. H. Herty, Jr. 1929—William E. Griffiths.

Jan 1, 1930

By Edmund C. Pechin

I REGRET that I am unable to present this subject in definite form and detail. All I shall attempt at this meeting is to lay before you some curious facts, the bearings and explanations of which must be reserved for future consideration. I hope before the next meeting to have carried experiments far enough to furnish a more important contribution to the science of iron metallurgy. The Wickersham process consists in the introduction into the molten metal, as it runs from the furnace, of air from the hot blast. Mr. Samuel Wickersham is the originator of the plan, as applied in practice, although Mr. Martien had the idea a long time ago, and, I believe, went to England about it. But at that time Mr. Bessemer was coming before the public with his invention, which engrossed the attention of iron-masters, and Mr. Martien accomplished nothing. The principal difficulty in our experiments at Dunbar was to get a practicable runner or trough, through which the molten metal should pass, and in which it should be exposed to the action of the Mast. The runner we used was ten feet long, and perforated on the sides to permit the entrance of the air-currents. When we used a cast-iron and fire-clay runner, the heat was so great that before we were more than half done with a run, the lower part of the runner was melted, and we had a magnificent Fourth of July display of fireworks until the blast was shut off. We had to abandon fire clay. The runner with which we have had the best success is made of wrong- ht-iron tubes, 29 inches in diameter, attached to a wrought-iron frame, and lined with a mixture of crushed conglornerate (quartz) and a little fire clay to give it cohesion. The wrought-iron shell curves inward over the upper edges, so as to catch and throw back into the current the flying sparks and particles of metal thrown out by ebullition. With this we have been able to run 12 to 14 tons at a heat with great ease. Mr. Wickersham has since prepared this material (pounded quartz) into a shaped brick or tile, with the necessary perforations for the passage of the air, which promises to answer every requirement for steady working. As regards the improvement in the quality of the iron, there seems to be no question. A large number of practical tests were made in

By Fred Wise, C. W. Wark

THE Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed. The oxide ore is not segregated. GENERAL METALLURGY The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxidized. The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices. On this basis metallurgical results are viewed in the light of an optimum tailing rather than a percentage of extraction. MILLING PRACTICE Crushing (Fig. 1).-There are three primary ore bins, one each for oxide ore, gougy sulphide ore, and hard sulphide ore. In front of each bin a substantial yard is maintained, which makes it possible to stockpile 2500 tons of oxidized ore, 1000 tons of hard sulphide ore, and 1000 tons of gougy sulphide ore. The bins are fed by a 60-hp. caterpillar bulldozer from the stockpiles. Fig. 1 shows the method and

Jan 1, 1940

By L. C. Armstrong

A. E. ROSS*—Mr. Armstrong in his paper stated that they had experienced considerable difficulty in drilling the quartz-feldspar intergrowths. The dia-mor~d loss was excessive and the diamond bits polished quite rapidly. Mr. Davidson, who presented the paper, stated that bortx stones in the range of 20 to 30 per carat had been used in the bits on this job. I would like to suggest the use of bits employing stones in the range of 60 to 100 per carat, an average of possibly 80 per carat. If these stones had been used the bits might have lasted longer and not polished so quickly. As a basis for this suggestion I would like to point out that in northern New York State we had at least two examples where bits employing stones in the range of 80 per carat had solved a difficult problem. Bits set with stones in the range of 20 to 30 per carat had been used previously and had failed. With the finer stones, the cost per foot of drilling decreased material1y. It should also be noted from a technical standpoint that the smaller stones require higher drilling speeds than the larger stones. Greater pressures are not normally necessary, and it is the higher speed which seems to be the major factor of importance. It should also be noted that the finer stones afford a greater number or cutting surfaces for the same carat weight in a bit. Then too, the smaller stones, by virtue of their size, serve as sharper cutting edges than larger stones. There is no doubt that the diamond bit employing smaller stones costs more to set than the bit using larger stones. However, with the technique developed at the shops of Sprague and Henwood, Inc., we feel that the relatively slight additional cost required to set these bits is more than paid for by the resultant lower drilling cost. We feel that the highest quality stone available is the most economical to use when hard fine grained rock is encountered. In summary, I would suggest that it might be possible to solve the problem presented in this paper by using a diamond bit employing stones at least as small as 80 per carat of the highest grade possible and by using the diamond bit at the highest speed available with modern drilling equipment. L. C. ARMSTRONG (author's reply) —It is generally agreed that the use of smaller, high-grade diamonds and of higher drilling speeds, as suggested by Mr. Ross, may be the best approach to the solution of the problem.

Jan 1, 1950

The officers and staff of the Petroleum Division are the servants of the members, and to the extent that the wishes of the members are made known and are practicable they will be carried out. The tentative plans outlined here are in general accord with previous custom, but modified by suggestions received recently from various members. The advice of all members is solicited, and it is hoped that the general expression on matters of policy can soon be facilitated by circulation of a questionnaire. Plans for two mid-year meetings of the Petroleum Division and for participation in the annual meeting at New York were inaugurated at the last annual meeting and are being carried forward as rapidly as possible in the belief that an early start will increase the possibility of finding the best available program material and permit the careful preparation, review, editing, and advance discussion of papers. While a number of papers have already been solicited, both members and nonmembers are hereby invited to submit additional papers, with the assurance that such papers will be given just as favorable consideration as the papers that have been requested. Mid-year meetings will be held at about the same time both in the Mid-Continent and California. The time will be selected if possible to coincide with the visits of President Lovejoy, who expects to be in California the last of September and in Texas early in October. Fort Worth, Dallas and Austin have been suggested for the Mid-Continent meeting. The Pacific Coast meeting will be held at Los Angeles. It is to be noted particularly that a Pacific Coast meeting was waived last year in favor of the annual meeting of the American Petroleum Institute, which was held at Los Angeles for the first time in nine years. It is hoped, and it was the understanding at the time among a number of individuals interested in both organizations, that in view of this action of the Petroleum Division the industry will give more than the usual support to the A.I.M.E. meeting this year. Ultimate Recovery is being considered as the keynote topic for the mid-year meetings. In view of trying financial conditions combined with an exceptionally high current potential rate of production, it is natural that the attention of the industry should be focused upon means of controlling production and reducing cost of operation. It seems that the Petroleum Division of the A.I.M.E., as a professional group, might

Jan 1, 1936